Vigo VG02029ST, VG02029CH, VG02029STK2, VG02029STK1, VG02029CHK2 Specifications

FAUCET SPECIFICATIONS
Pull-Down Spray Kitchen Faucet
Model VG02029
MODEL VG02029
FEATURES
PACKING LIST
DIMENSIONS
MODEL #	HOLE	FAUCET	SPRAYER
	DIAMETER	HEIGHT	REACH
VG02029	1 3/8"	18"	9 1/4"
			18"
		9 1/4"
8 1/4"
NOTE: All faucets are compliant to CEC 2016 regulations. If you
have inquiries about your water flow, please email
[e-mail].

FUNCTION

BUTTON

8 1/4"

SIDE VIEW

	18"

9 1/4"

6 5/8"

2"

1 1/2" MAX.

SPRAY HOSE

FRONT VIEW

TOP VIEW

VG02029

THE MEASUREMENTS IN INCHES ARE ROUNDED TO THE NEAREST 3/8"

2

	PACKAGE CONTENTS				ASSEMBLY
		RUBBER RING		COUNTERWEIGHT	1. SHUT OFF WATER SUPPLY. REMOVE THE OLD FAUCET
					AND FLEXIBLE HOSES. CLEAN SINK SURFACE WITH A NON
					ABRASIVE CLEANER IN PREPARATION FOR THE NEW FAUCET.
								1
		METAL RING	PLASTIC HOLDER
				NUT
					2. THREAD FEMALE END OF METAL BRAIDED HOSE TO THE			2
					FAUCET (2).
					!	ENSURE THAT YOU USE PIPE TAPE AND DO NOT OVER
						TIGHTEN THE SUPPLY LINE NUTS AS THIS COULD CAUSE
		SPRAYER				PRODUCT FAILURE LEADING TO WATER DAMAGE.
	FAUCET	TWO METAL	ALLEN KEY (REMOVES HANDLE
	ASSEMBLY	BRAIDED HOSES
				TO ACCESS CARTRIDGE)
	REQUIRED TOOLS				3. POSITION THE FAUCET IN THE COUNTERTOP HOLE, FROM
	Adjustable wrench				BENEATH THE COUNTERTOP HOLE ASSEMBLE THE PLASTIC
	Allen key - supplied (to remove cartridge if needed)				HOLDER, RUBBER RING, AND METAL RING IN THE ORDER			3
					DEPICTED IN THE DIAGRAM. THEN THREAD METAL NUT ONTO
	Plumber's putty - optional				HOLLOW PIN. TIGHTEN THE METAL NUT UNTIL FAUCET IS
	Pipe tape				SECURE.
	Flat screwdrivers				!	ENSURE THAT PARTS ARE ASSEMBLED IN THE ORDER AS
	SAFETY TIPS
						DEPICTED IN DIAGRAM TO PREVENT DAMAGE TO FAUCET AND
						SUPPLY LINES.
	If you use soldering for the installation of the faucet,		the seats, cartridges and
	washers will have to be removed before using flame. Damage caused by
	improper soldering will void the warranty.
	Protect your eyes with safety glasses when cutting or soldering water supply
	lines.						STABILIZES FAUCET
	IMPORTANT POINTS						UNDER COUNTERTOP
	Prior to beginning installation, turn off the cold and hot water lines and open the						NUT
	hot and cold knobs on the old faucet to release pressure.
	When installing your new faucet, turn the connector nuts			finger-tight, then use
	one wrench to anchor the fitting and a second wrench to tighten the nut.				4. ATTACH SPRAY HOSE TO THE COPPER PIN (THE LONGEST
	Connections that are too tight will reduce the integrity of			the system and	PIN). PUSH IN THE TAB AND SLIDE THE SPRAY HOSE INTO THE
	potentially cause product failure which could lead to water damage.				COPPER PIN. IT WILL MAGNETICALLY ATTACH. ATTACH
					SUPPLIED COUNTERWEIGHT TO THE HOSE.
	Wrap all threaded connections with pipe tape available at your local hardware or
	plumbing supply store. Always wrap in a clockwise direction.				5. (IF NOT DONE ALREADY) ATTACH
	Not all necessary supplies to install your faucet are included, however, they are				SPRAYER TO FEMALE CONNECTION
	available wherever plumbing supplies are sold.				OF SPRAYER HOSE BY HAND AND			4
					TIGHTEN UNTIL SECURE. MAKE SURE
	Prior to installing the faucet please FLUSH THE HOT AND COLD WATER				THE BLACK WASHER WITH SCREEN IS
	SUPPLY LINES that are or will be connected to the new faucet to remove scale,				SEATED AND INSTALLED PROPERLY.
	solder or their impurities which could damage the faucet and potentially void the				!	USE WASHER WITH SCREEN AT
	warranty.
						CONNECTION POINT BETWEEN
						SPRAYER AND SPRAYER HOSE. THIS
						WILL STOP DEBRIS FROM TRAVELING	TAB
						INTO THE SPRAYER HEAD AND
	MAINTENANCE					EFFECTING ITS FUNCTIONALITY.
						PLEASE NOTE THAT THE SCREEN
						WASHER WILL NEED TO BE REMOVED
	Your new faucet is designed for years of trouble-free		performance.
						AND CLEANED APPROXIMATELY ONCE
	Keep it looking new by cleaning it periodically with a soft			cloth. Avoid abrasive		EVERY 3 MONTHS TO AVOID BUILD UP
						AND LOW WATER FLOW.
	cleaners, steel wool and harsh chemicals as these will scratch, dull, and/or				6. ATTACH THE FEMALE CONNECTIONS OF THE FLEXIBLE HOSES TO
	damage the	finish and void the warranty.
					THE COLD AND HOT WATER SUPPLY .
					!	ENSURE THAT YOU USE PIPE TAPE AND ADJUSTABLE WRENCH, DO NOT
	INSTALLATION					OVER TIGHTEN AS THIS COULD CAUSE PRODUCT FAILURE LEADING TO
						WATER DAMAGE.		6
	Installation must be done by a qualified licensed plumber.
	Prior to installation please read the instructions thoroughly, confirm that all parts				7. AFTER INSTALLATION IS COMPLETE,		TURN ON THE WATER SUPPLY AND ALLOW BOTH
	are included and visually inspect the unit for any defects.				HOT AND COLD WATER TO RUN SEPARATELY FOR AT LEAST TWO MINUTE EACH. WHILE
					WATER IS RUNNING, CHECK FOR LEAKS. IT IS IMPORTANT TO VIEW THE CONNECTIONS
	If you have any questions please contact the Vigo Technical Support
					AT THE MALE AND FEMALE FLEXIBLE HOSE CONNECTIONS. IF LEAKS ARE DETECTED,
	Department before proceeding with installation.				REFER BACK TO THE INSTRUCTIONS AND ADJUST ACCORDINGLY. TIGHTENING NUTS
					SLIGHTLY MAY STOP ANY MINOR LEAKS.

3

TROUBLESHOOTING

	PROBLEM	POTENTIAL CAUSE		CORRECTIVE ACTION
	1 - Leaks from handle	1.A - Cartridge unseated	1.A - Remove cartridge from housing, wash thoroughly with hot
	2 - Insufficient flow rate	1.B - Cartridge defective	water and reseat in housing.
	3 - Leak at connection points	2.A - Dirty aerator	1.B - Contact Vigo Technical Support for replacement.
		2.B - Clog in supply hose / line
	4 - Loose faucet body		2.A	- Remove and soak / clean with a non abrasive agent (i.e.
	5 - Sprayer button stops working
		3.A - Sprayer hose not tight	vinegar).
		3.B - Flexible hose leaking at body or connection point	2.B	- Remove sprayer or supply line and flush lines
		4. - Metal nut became loose	3.A	- Remove sprayer and check integrity of the black washer.
			Make sure the washer is seated properly and retighten.
		5.A - Debris in aerator	3.B	- Tighten hoses. If this does not resolve the issue, remove
		5.B - Wear and tear on button	the flexible hose and rethread, checking to make sure the
			connection is secure. Make sure to use pipe tape.
			4. - From under the counter, use an adjustable wrench and
			tighten the metal nut to the hollow pipe. Make sure the faucet is
			perpendicular to the counter.
			5.A	- Remove and clean aerator.
			5.B	- Contact Vigo Technical Support for replacement.

PARTS LIST - For any parts needed but not shown, please contact Vigo Technical Support

PART	PART #	FINISH	SUPPLY DATE INDICATOR (INTERNAL USE ONLY)
Sprayer Hose	74046	CH, ST, MB	P
Sprayer	78105	CH, ST, MB	P
Handle	78103	CH, ST, MB	P
Sedal Cartridge	74026	-	P
Metal braided Hose	74020	-	P
Sprayer Washer	74008	-	P
Black Washer with Screen	74010	-	P

TOLL FREE: (866) 591 - 7792

E-Mail: [e-mail]

www.vigoindustries.com

NSF / ANSI 61

4

VIGO INDUSTRIES, LLC ("VIGO")

FAUCET LIMITED LIFETIME WARRANTY

EFFECTIVE APRIL 1, 2013

VIGO offers the following limited warranty on each of its Faucet products (the "Product") and the components thereof. This warranty extends only to the original owner for personal household use. For commercial uses, additional limitations apply.

VIGO warrants the structure of the Product to be free from defects in workmanship and materials under normal use and service for the period commencing from the initial date of purchase by the owner, contractor, or builder, from VIGO or an authorized VIGO dealer, through the lifetime of the original owner or end-user.

VIGO warrants the cartridge component of the Product to be free from defects in workmanship and materials under normal use and service for a period of five (5) years from the initial date of purchase by the owner, contractor, or builder, from VIGO or an authorized VIGO dealer.

VIGO warrants the spray assembly and other mechanical components of the Product to be free from defects in workmanship and materials under normal use and service for a period of one (1) year from the initial date of purchase by the owner, contractor, or builder, from VIGO or an authorized VIGO dealer.

Subject to the Warranty Service provision below, any product reported to the authorized dealer or to VIGO as being defective within the warranty period will be repaired or replaced (with a product of equal value) at the option of VIGO. This warranty extends to the original owner and is not transferable to a subsequent owner.

Neither the distributor, authorized VIGO dealer, nor any other person has been authorized to make any affirmation, representation, or warranty other than those contained in this warranty. Any affirmation, representation, or warranty other than those contained in this warranty shall not be enforceable against VIGO or any other person.

VIGO reserves the right to modify this warranty at any time, it being understood that such modifications will not alter the warranty conditions applicable at the time of sale of the products in question.

Limitations

This warranty shall not apply to instances of incorrect operating procedures, breakages, or damages caused by fault through improper installation, carelessness, abuse, misuse, misapplication, improper maintenance, or alteration of the Product, as well as chemical or natural corrosion, accident, fire, flood, an act of God, or any other casualty. Avoid abrasive cleaners, steel wools, and harsh chemicals as these will scratch, damage, and / or dull the product and / or finish and void this warranty. The owner of the Product covered by the present warranty is entirely responsible for its proper installation and any applicable plumbing or electrical wiring. VIGO neither installs nor supervises the installation nor hires a contractor for this purpose; consequently, VIGO cannot be held responsible for any default, breakage, or damages caused thereby or resulting thereof, either directly or indirectly.

The owner must provide access to the components of the Product as described in the installation guide so that VIGO can execute the warranty specified herein. If such access is not available, all expenses to provide said access will be the responsibility of the owner.

This warranty does not apply to Products that have not been installed or operated in accordance with instructions supplied by VIGO and all applicable rules, regulations, and legislation pertaining to such installations.

This warranty does not apply unless the VIGO Product is installed by fully insured licensed professionals. Vigo strongly recommends that such licensed professionals have experience in the installation of bathroom and kitchen products. [Installation of certain products, including without limitation glass products (i.e., shower doors and glass sinks) by an inexperienced person may result in product failure including, but not limited to, glass breakage which could result in personal injury or death.]

VIGO is not liable for personal injuries or deaths to any persons or for any direct, special, incidental, or consequential damage, loss of time, loss of profits, inconvenience, incidental expenses, labor or material charges, or any other costs resulting from the use of the product or equipment or pertaining to the application of the present warranty, or resulting from the removal or replacement of any product or element or part covered by this warranty.

EXCEPT AS OTHERWISE PROVIDED ABOVE, VIGO MAKES NO WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE OR COMPLIANCE WITH ANY CODE.

In any case, VIGO cannot be held liable for any amount over and above the purchase price paid for the Product by the owner/end-user, contractor, or builder.

Commercial Limitations

In addition to the above conditions and limitations, the warranty period for products installed for commercial applications or used in commercial ventures is one (1) year from the initial date of purchase by the owner, contractor, or builder from an authorized dealer. VIGO is not responsible for loss of use or profit under any circumstances. If the product is used as a display, the warranty period begins from the date of purchase. This warranty gives the owner specific legal rights. The owner may also have other rights which can vary from one state or province to another.

Warranty Service

In order to obtain service provided under this warranty during regular business hours, contact the dealer or distributor who sold the unit, or contact VIGO directly. VIGO will provide the warranty service described above when the following conditions have been met: the failure is of the nature or type covered by the warranty; the user has informed an authorized VIGO Agent or VIGO's warranty service department representative of the nature of the problem during the warranty period; conclusive evidence (e.g., proof of purchase or installation) is provided to the foregoing by the user proving that the failure occurred or was discovered within the warranty period; an authorized independent service person or company representative has been permitted to inspect the product during regular business hours within a reasonable time after the problem was reported by the user. Vigo's warranty obligation shall be discharged upon tender of replacement or repair. The customer's refusal to accept the tender terminates VIGO's warranty obligations.

Certification may be ended by VIGO or certification agencies without notice.

5