21.5-INCH VALUE TFT-LED MONITOR (with SDI interface)
USER MANUAL
Please read this manual thoroughly before use, and keep it handy for future reference.
SAFETY INSTRUCTION ………………………………………………………….…… |
2 ~ 3 |
CAUTIONS …………………………………………………………….......................... |
4 |
FCC RF INTERFERENCE STATEMENT ……………………………....................... |
5 |
INSTALLATION ………………………………………………………………………….. |
6 |
CONNECTING WITH EXTERNAL EQUIPMENT …………………………………… |
7 |
REMOTE FUNCTIONS ………………………………………………………………… |
8 |
CONTROLS AND FUNCTIONS ……………………………………………………….. |
9 ~ 16 |
MOUNTING GUIDE …………………………………………………………………….. |
17 |
D-SUB CONNECTOR PIN ASSIGNMENTS ………………………………………… |
18 |
POWER MANAGEMENT ……………………………………………………………… |
19 |
SPECIFICATION ……………………………………………………………………… |
20 |
TROUBLE SHOOTING GUIDE …………………………………………………......... |
21 |
This Monitor was
Manufactured by ISO 9001
Certified Factory
- 1 -
Important Safety Instruction
1.Read these instructions.
2.Keep these Instructions.
3.Heed all warnings.
4.Follow all instructions.
5.Do not use this apparatus near water.
6.Clean only with dry cloth.
7.Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
8.Do not install near any heat sources such as radiators, heat registers,stoves, or other apparatus (including amplifiers) that produce heat.
9.Do not defeat the safety purpose of the polarized or grounding-type plug. Apolarized plug has two blades with one wider than the other. Agrounding type plug has two blades and a third grounding prong.
The wide blade or the third prong are provided for your safety.
If the provided plug does not fit into your outlet, consult an electrician for replacement of the bsolete outlet.
10.Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles and the point where they exit from the apparatus.
11.Only use attachment/accessories specified by the manufacturer.
12.Use only with the cart, stand, tripod, bracket or table specified by the manufacturer or sold with the apparatus. When a cart is used, use caution when moving
the cart/apparatus combination to avoid injury from tip-over.
13.Unplug this apparatus during lightning storms or when unused
for long periods of time.
14.Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus the apparatus has been exposed to rain or moisture does not operate normally or has been dropped.
- 2 -
-The apparatus shall not be exposed to dripping or splashing and that no objects filled with liquids, such as vases, shall be placed no the apparatus.
14 Minimum distances(e.g. 10cm) around the apparatus for sufficient ventilation.
“WARNING – To reduce the risk of fire or electric shock, do not expose the apparatus to rain or moisture.”
“The apparatus shall not be exposed to dripping or splashing and no objects filled with liquids, such as vases, shall be placed on the apparatus.”
This symbol is intended to alert the user to the presence of uninsulated: dangerous voltage with in the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
This symbol is intended to alert the user to the presence of important operating and maintenance(servicing) instructions in the literature accompanying the appliance.
- 3 -
CAUTION
The power supply cord is used as the main disconnect device, ensure that the socket-outlet is located/installed near the equipment and is easily accessible.
ATTENTIONN
Le cordon d`alimentation est utillsé comme interrupteur général. La prise de courant doit être située ou installée à proximité du matériel et être facile d`accès
NEVER REMOVE THE BACK COVER
Removal of the back cover should be carried out only by qualified personnel.
DO NOT USE IN HOSTILE ENVIRONMENTS
To prevent shock or fire hazard, do not expose the unit to rain or moisture.
This unit is designed to be used in the office or home. Do not subject the unit to vibrations, dust of corrosive gases.
KEEP IN A WELL VENTILATED PLACE
Ventilation holes are provided on the cabinet to prevent the temperature from rising. Do not cover the unit or place anything on the top of unit.
AVOID HEAT
Avoid placing the unit in direct sunshine or near a heating appliance.
TO ELIMINATE EYE FATIGUE
Do not use the unit against a bright back ground and where sunlight or other light sources will shine directly on the monitor.
BE CAREFUL OF HEAVY OBJECT
Neither the monitor itself nor any other heavy object should rest on the power cord. Damage to a power cord can cause fire or electrical shock.
- 4 -
NOTE
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures.
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio, TV technician for help.
-Only shielded interface cable should be used.
Finally, any changes or modifications to the equipment by the user not expressly approved by the grantee or manufacturer could void the users authority to operate such equipment.
DOC COMPLIANCE NOTICE
This digital apparatus does not exceed the Class A limits for radio noise emissions from digital apparatus set out in the radio interference regulation of Canadian Department of communications.
- 5 -
Before setting up the monitor, ensure that the power to the monitor and other attached devices are turned off.
Notice: Stand & Screws are optional
A.Connecting the stand
1.Place the monitor with its front facing downward on a soft cloth.
2.Assemble the Stand Base into the Stand Body in the correct direction using the included screws in the accessory box.
Stand Base |
Stand Body |
FS4x10 screws
3.Once assembled take the monitor up carefully and face the front side.
B.Positioning your display
Adjust the position of the panel in various ways for maximum comfort. (Tilt Range: -3°~75°)
-3˚ |
75˚ |
- 6 -
A. Rear Connection
1 |
2 |
3 |
4 |
5 |
6 |
7 |
8 |
9 |
10 |
11 |
12 |
13 |
1.SDI OUT
2.SDI IN
3.AV2 IN
4.AV1 OUT
5.AV1 IN
6.TRIGGER IN
7 & 8. AUDIO R&L (AV1 & AV2)
9.PC STEREO IN (VGA & DVI)
10.VGA
11.DVI
12.HDMI
13.DC 12V
- 7 -
Loading...