ViewSonic PA503X, PA503W, PA503S User Manual

4 (1)

PA500S/PA503S/PA500X/PA503X/

PA503W

DLP Projector

User Guide

IMPORTANT: Please read this User Guide to obtain important information on installing and using your product in a safe manner, as well as registering your product for future service. Warranty information contained in this User Guide will describe your limited coverage from ViewSonic Corporation, which is also found on our web site at http://

boxin the upper right corner of our website. “Antes de operar su equipo lea cu idadosamente las instrucciones en este manual”

Model No. VS16955/VS16905/VS16956/VS16909/VS16907

Compliance Information

FCC Statement

This device complies with part 15 of FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

Consult the dealer or an experienced radio/TV technician for help.

Warning: by the party responsible for compliance could void your authority to operate the equipment.

For Canada

CAN ICES-3 (B)/NMB-3(B)

CE Conformity for European Countries

The device complies with the EMC Directive 2014/30/EU and Low Voltage Directive 2014/35/EU.

Following information is only for EU-member states:

The mark is in compliance with the Waste Electrical and Electronic Equipment Directive 2012/19/EU (WEEE).

The mark indicates the requirement NOT to dispose the equipment including any spent or discarded batteries or accumulators as unsorted municipal waste, but use the return and collection systems available.

If the batteries, accumulators and button cells included with this equipment, display the chemical symbol Hg, Cd, or Pb, then it means that the battery has a heavy metal content of more than 0.0005% Mercury or more than, 0.002% Cadmium, or more than 0.004% Lead.

i

Important Safety Instructions

1.Read these instructions.

2.Keep these instructions.

3.Heed all warnings.

4.Follow all instructions.

5.Do not use this unit near water.

6.Clean with a soft, dry cloth.

7.Do not block any ventilation openings. Install the unit in accordance with the manufacturer’s instructions.

8.Do not install near any heat sources such as radiators, heat registers, stoves,

9.Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade and the third! outlet, consult an electrician for replacement of the obsolete outlet.

10.Protect the power cord from being walked on or pinched particularly at plugs. Convenience receptacles and the point where they exit from the unit. Be sure that the power outlet is located near the unit so that it is easily accessible.

"" # $ &

"' * & + & & the manufacturer, or sold with the unit. When a cart is used, use caution when moving the cart/unit combination to avoid injury from tipping over.

13. Unplug this unit when unused for long periods of time.

"; < = < unit has been damaged in any way, such as: if the power-supply cord or plug is damaged, if liquid is spilled onto or objects fall into the unit, if the unit is exposed to rain or moisture, or if the unit does not operate normally or has been dropped.

ii

Declaration of RoHS2 Compliance

This product has been designed and manufactured in compliance with Directive 2011/65/EU of the European Parliament and the Council on restriction of the use of certain hazardous substances in electrical and electronic equipment (RoHS2 Directive) and is deemed to comply with the maximum concentration values issued by the European Technical Adaptation Committee (TAC) as shown below:

Substance

Proposed Maximum

Actual Concentration

Concentration

 

 

Lead (Pb)

0.1%

< 0.1%

Mercury (Hg)

0.1%

< 0.1%

Cadmium (Cd)

0.01%

< 0.01%

Hexavalent Chromium (Cr6+)

0.1%

< 0.1%

Polybrominated biphenyls (PBB)

0.1%

< 0.1%

Polybrominated diphenyl ethers (PBDE)

0.1%

< 0.1%

Certain components of products as stated above are exempted under the Annex III of the RoHS2 Directives as noted below:

Examples of exempted components are:

1.@ J J lamps (CCFL and EEFL) for special purposes not exceeding (per lamp):

(1)Short length ( 500 mm): maximum 3.5 mg per lamp.

(2)Medium length ( 500 mm and 1,500 mm): maximum 5 mg per lamp.

(3)Long length ( 1,500 mm): maximum 13 mg per lamp.

2.Lead in glass of cathode ray tubes.

3.Q J & X 'Y &

4.Lead as an alloying element in aluminium containing up to 0.4% lead by weight.

5.Copper alloy containing up to 4% lead by weight.

6.Lead in high melting temperature type solders (i.e. lead-based alloys containing 85% by weight or more lead).

7.Electrical and electronic components containing lead in a glass or ceramic other than dielectric ceramic in capacitors, e.g. piezoelectronic devices, or in a glass or ceramic matrix compound.

iii

Copyright Information

Copyright © ViewSonic® Corporation, 2017. All rights reserved. Macintosh and Power Macintosh are registered trademarks of Apple Inc.

Microsoft, Windows, Windows NT, and the Windows logo are registered trademarks of Microsoft Corporation in the United States and other countries.

ViewSonic, the three birds logo, OnView, ViewMatch, and ViewMeter are registered trademarks of ViewSonic Corporation.

VESA is a registered trademark of the Video Electronics Standards Association. DPMS and DDC are trademarks of VESA.

PS/2, VGA and XGA are registered trademarks of International Business Machines Corporation.

Disclaimer: ViewSonic Corporation shall not be liable for technical or editorial errors or omissions contained herein; nor for incidental or consequential damages resulting from furnishing this material, or the performance or use of this product.

In the interest of continuing product improvement, ViewSonic Corporation reserves! - ment may change without notice.

No part of this document may be copied, reproduced, or transmitted by any means, for any purpose without prior written permission from ViewSonic Corporation.

Product Registration

To fulfill possible future product needs, and to receive additional product information as it becomes available, please visit your region section on ViewSonic’s website to register your product online.

The ViewSonic CD also provides an opportunity for you to print the product registration form. Upon completion, please mail or fax to a respective ViewSonic office. To find your registration form, use the directory “:\CD\Registration”. Registering your product will best prepare you for future customer service needs. Please print this user guide and fill the information in the “For Your Records” section. For additional information, please see the “Customer Support” section in this guide.

 

For Your Records

Product Name:

PA500S/PA503S/PA500X/PA503X/PA503W

 

ViewSonic DLP Projector

Model Number:

VS16955/VS16905/VS16956/VS16909/VS16907

Document Number:

PA500S/PA503S/PA500X/PA503X/PA503W_UG_ENG

 

Rev. 1A 06-13-17

Serial Number:

________________________________________

Purchase Date:

________________________________________

Product disposal at end of product life

The lamp in this product contains mercury which can be dangerous to you and the environment. Please use care and dispose of in accordance with local, state or federal laws.

ViewSonic respects the environment and is committed to working and living green. Thank you for being part of Smarter, Greener Computing. Please visit ViewSonic website to learn more.

USA & Canada: http://www.viewsonic.com/company/green/recycle-program/ Europe: http://www.viewsoniceurope.com/eu/support/call-desk/

Taiwan: http://recycle.epa.gov.tw/recycle/index2.aspx

iv

Table of contents

Important safety

 

instructions .......................

2

Introduction......................

4

Projector features .................................

4

Shipping contents.................................

4

Controls and functions .........................

5

Positioning your projector

............................................

9

Choosing a location..............................

9

Projection dimensions........................

10

Connection ......................

13

Connecting a computer or monitor ....

14

Connecting Video source devices ......

15

Playing sound through the projector ..

16

Operation ........................

17

Starting up the projector.....................

17

Using the menus.................................

18

Utilizing the password function .........

19

Switching input signal........................

21

Adjusting the projected image ...........

22

Magnifying and searching for details

 

............................................................

23

Selecting the aspect ratio ...................

23

Optimizing the image.........................

24

Setting the presentation timer ............

28

Hiding the image................................

29

Locking control keys..........................

29

Operating in a high altitude environment

............................................................

29

Using the CEC function .....................

30

Using the 3D functions ......................

30

Using the projector in standby mode

 

...........................................................

31

Adjusting the sound ...........................

31

Shutting down the projector ..............

32

Menu operation..................................

33

Maintenance ...................

43

Care of the projector ..........................

43

Using the dust filter (optional

 

accessory) ..........................................

43

Lamp information ..............................

45

Troubleshooting .............

48

Specifications ..................

49

Dimensions ........................................

49

Ceiling mount installation .................

49

IR control table ..................................

50

RS232 command table.......................

51

Timing chart ......................................

61

Projector specifications......................

65

Copyright information...

66

1

Important safety instructions

Your projector is designed and tested to meet the latest standards for safety of information technology equipment. However, to ensure safe use of this product, it is important that you follow the instructions mentioned in this manual and marked on the product.

Safety Instructions

1.Please read this manual before you operate your projector. Save it for future reference.

2.Do not look straight at the projector lens during operation. The intense light beam may damage your eyes.

3.Refer servicing to qualified service personnel.

4.Always open the lens shutter or remove the lens cap when the projector lamp is on.

5.In some countries, the line voltage is NOT stable. This projector is designed to operate safely within a mains voltage between 100 to 240 volts AC, but could fail if power cuts or surges of ±10 volts occur. In areas where the mains voltage may fluctuate or cut out, it is recommended that you connect your projector through a power stabilizer, surge protector or uninterruptible power supply (UPS).

6.Do not block the projection lens with any objects when the projector is under operation as this could cause the objects to become heated and deformed or even cause a fire. To temporarily turn off the lamp, press BLANK on the projector or remote control.

7.The lamp becomes extremely hot during operation. Allow the projector to cool for approximately 45 minutes prior to removing the lamp assembly for replacement.

8.Do not operate lamps beyond the rated lamp life. Excessive operation of lamps beyond the rated life could cause them to break on rare occasions.

9.Never replace the lamp assembly or any electronic components unless the projector is unplugged.

10.Do not place this product on an unstable cart, stand, or table. The product may fall, sustaining serious damage.

11.Do not attempt to disassemble this projector. There are dangerous high voltages inside which may cause death if you should come into contact with live parts. The only user serviceable part is the lamp which has its own removable cover.

Under no circumstances should you ever undo or remove any other covers. Refer servicing only to suitably qualified professional service personnel.

12.Do not place this projector in any of the following environments.

-Space that is poorly ventilated or confined. Allow at least 50 cm clearance from walls and free flow of air around the projector.

-Locations where temperatures may become excessively high, such as the inside of a car with all windows rolled up.

-Locations where excessive humidity, dust, or cigarette smoke may contaminate optical components, shortening the projector's life span and darkening the picture.

-Locations near fire alarms

-Locations with an ambient temperature above 40°C / 104°F

-Locations where the altitudes are higher than 3000 m (10000 feet).

2

13.Do not block the ventilation holes. If the ventilation holes are seriously obstructed, overheating inside the projector may result in a fire.

-Do not place this projector on a blanket, bedding or any other soft surface.

-Do not cover this projector with a cloth or any other item.

-Do not place inflammables near the projector.

14.Always place the projector on a level, horizontal surface during operation.

-Do not use if tilted at an angle of more than 10 degrees left to right, nor at angle of more than 15 degrees front to back. Using the projector when it is not fully horizontal may cause a malfunction of, or damage to, the lamp.

15.Do not stand the projector on end vertically. Doing so may cause the projector to fall over, causing injury or resulting in damage to the projector.

16.Do not step on the projector or place any objects upon it. Besides probable physical damage to the projector, doing so may result in accidents and possible injury.

17.Do not place liquids near or on the projector. Liquids spilled into the projector may cause it to fail. If the projector does become wet, disconnect it from the power supply's wall socket and call your local service center to have the projector serviced.

18.This product is capable of displaying inverted pictures for ceiling mount installation.

Use only qualified ceiling mount kit for mounting the projector and ensure it is securely installed.

19.When the projector is under operation, you may sense some heated air and odor from its ventilation grill. It is a normal phenomenon and not a product defect.

20.Do not use the Security bar for transporting or installation. It should be used with a commercially available theft prevention cable.

21.CAUTION

Possibly hazardous optical radiation emitted from this product. Do not stare at operating lamp. May be harmful to the eyes. Risk Group 2

Warning

THIS APPARATUS MUST BE EARTHED.

When installing the unit, incorporate a readily accessible disconnect device in the fixed wiring, or connect the power plug to an easily accessible socket-outlet near the unit. If a fault should occur during operation of the unit, operate the disconnect device to switch the power supply off, or disconnect the power plug.

Safety instructions for ceiling mounting of the projector

We want you to have a pleasant experience using your projector, so we need to bring this safety matter to your attention to prevent damage to person and property.

If you intend to mount your projector on the ceiling, we strongly recommend that you use a proper fitting projector ceiling mount kit and that you ensure it is securely and safely installed.

If you use an inappropriate projector ceiling mount kit, there is a safety risk that the projector may fall from the ceiling due to an improper attachment through the use of the wrong gauge or length screws.

You can purchase a projector ceiling mount kit from the place you purchased your projector. We recommend that you also purchase a separate security cable and attach it securely to both the anti-theft lock slot on the projector and the base of the ceiling mount bracket. This will perform the secondary role of restraining the projector should its attachment to the mounting bracket become loose.

3

Introduction

Projector features

The projector integrates high-performance optical engine projection and a user-friendly design to deliver high reliability and ease of use.

Some of the features may not be available on your projector. Actual performance may vary and subject to model specifications.

Power saving function decreasing the power consumption of the lamp by up to 70% when no input signal can be detected for a set period of time.

Presentation timer for better control of time during presentations

Supports 3D display

Color Management allowing color adjustments to your liking

Less than 0.5W power consumption when power saving mode is turned on

Screen Color correction allowing projection on surfaces of several predefined colors

Quick auto search speeding up the signal detecting process

Color modes providing choices for different projection purposes

One-key auto-adjustment to display the best picture quality (only for analog signal)

Digital keystone correction to correct distorted images

Adjustable color management control for data/video display

Ability to display 1.07 billion colors

Multi-language On-Screen Display (OSD) menus

Switchable normal and economic modes to reduce the power consumption

Component HDTV compatibility (YPbPr)

HDMI CEC (Consumer Electronics Control) function allows synchronized power ON/ OFF operation between the projector and a CEC-compatible DVD player device connected to the HDMI input of the projector

The apparent brightness of the projected image will vary depending on the ambient lighting conditions, selected input signal contrast/brightness settings, and is directly proportional to projection distance.

The lamp brightness will decline over time and may vary within the lamp manufacturers specifications. This is normal and expected behavior.

Shipping contents

1.Projector

2.Power Cord

3.Quick Start Guide

4.Remote Control & Batteries

5.VGA Cable

6.Replacement lamp (optional) (Please contact qualified service personnel for changing the lamp)

7.Soft carry case (optional)

8.VGA-Component adapter (optional)

9.Dust filter (optional)

4

Controls and functions

Projector

Power indicator light

Temperature indicator light

Lamp indicator light

Focus ring

Zoom ring

Power

Toggles the projector between standby mode and Power ON.

/ (Keystone keys)

Manually corrects distorted images resulting from an angled projection.

Left/ Right/ Up/ Down

Selects the desired menu items and makes adjustments when the On-Screen Display (OSD) menu is activated.

Menu

Turns on the On-Screen Display (OSD) menu.

Exit

Goes back to previous OSD menu, exits and saves menu settings.

Source

Displays the source selection bar.

(Help)

Displays the HELP menu with a long press for 3 seconds.

Blank

Hides the screen picture.

Enter

Enacts the selected On-Screen Display (OSD) menu item when the On-Screen Display (OSD) menu is activated.

Color Mode

Selects an available picture setup mode.

(Volume Up)

Increases the volume level.

(Volume Down)

Decreases the volume level.

5

Remote control

To use the remote mouse control keys (Page Up, Page Down), see "Using the remote PgUp/PgDn function" on page 7 for details.

On/ Off

Toggles the projector between standby mode and Power ON.

COMP

Selects source from Computer In port for display.

VIEDO

Selects source from VIDEO or S- VIDEO port for display.

HDMI

Selects source from HDMI port for display.

Auto Sync

Automatically determines the best picture timings for the displayed image.

Source

Displays the source selection bar.

/ (Keystone keys)

Manually corrects distorted images resulting from an angled projection.

Enter

Enacts the selected On-Screen Display (OSD) menu item.

Left/ Right/Up/ Down

Selects the desired menu items and makes adjustments.

Menu

Turns on the On-Screen Display (OSD) menu.

(Information)

Displays the INFORMATION menu.

Exit

Exits and saves menu settings.

6

Aspect

Displays the aspect ratio selection bar.

Freeze

Freezes the screen picture.

Pattern

Displays embedded test pattern.

Blank

Hides the screen picture.

PgUp (Page Up)/PgDn (Page Down)

Operates your display software program (on a connected PC) which responds to page up/down commands (like Microsoft PowerPoint).

Only available when a PC input signal is selected.

Eco Mode

Displays the lamp mode selection bar.

(Volume Up)

Increases the volume level.

(Volume Down)

Decreases the volume level.

(Mute)

Toggles the projector audio between on and off.

(Zoom In)

Magnifies the projected picture size.

(Zoom Out)

Reduces the projected picture size.

Color Mode

Displays the color mode selection bar.

Remote control code

The projector can be assigned to 8 different remote control codes, 1 to 8. When several adjacent projectors are in operation at the same time, switching the remote control codes can prevent interference from other remote controls. Set the remote control code for the projector first before changing that for the remote control.

To switch the code for the projector, select from among 1 to 8 in the SYSTEM > Remote Control Code menu.

To switch the code for the remote control, press ID set and the number button corresponding to the remote control code set in the projector OSD together for 5 seconds or more. The initial code is set to 1. When the code is switched to 8, the remote control can control every projector.

If different codes are set on the projector and remote control, there will be no response from the remote control. When that happens, a message will display to remind you to switch the code for the remote control.

Using the remote PgUp/PgDn function

The capability of operating your computer with the remote control gives you more flexibility when delivering presentations.

1.Set the input signal to a PC signal.

2.Connect the projector to your PC or notebook with a USB cable prior to using the remote control in place of your computer’s mouse. See "Connecting a computer or monitor" on page 14 for details.

7

3.To operate your display software program (on a connected PC) which responds to page up/down commands (like Microsoft PowerPoint), press PgUp/PgDn.

Remote control effective range

Refer to the illustration about the location of the InfraRed (IR) remote control sensor(s). The remote control must be held at an angle within 30 degrees perpendicular to the projector's IR remote control sensor(s) to function correctly. The distance between the remote control and the sensor(s) should not exceed 8 meters (~ 26 feet).

Make sure that there are no obstacles between the remote control and the IR sensor(s) on the projector that might obstruct the infra-red beam.

Approx. 30°

Replacing the remote control batteries

1.To open the battery cover, turn the remote control over to view its back, press on the finger grip on the cover and slide it down in the direction of the arrow as illustrated.

2.Remove any existing batteries (if necessary) and install two AAA batteries observing the battery polarities as indicated in the base of the battery compartment. Positive (+) goes to positive and negative (-) goes to negative.

3.Refit the cover by aligning it with the base and pushing it back down into position. Stop when it clicks into place.

WARNING

Avoid leaving the remote control and batteries in an excessive heat or humid environment like the kitchen, bathroom, sauna, sunroom or in a closed car.

Replace only with the same or equivalent type recommended by the battery manufacturer.

Dispose of the used batteries according to the manufacturer's instructions and local environment regulations for your region.

Never throw the batteries into a fire. There may be danger of an explosion.

If the batteries are drained or if you will not be using the remote control for an extended period of time, remove the batteries to avoid damage to the remote control from possible battery leakage.

8

Positioning your projector

Choosing a location

Your room layout or personal preference will dictate which installation location you select. Take into consideration the size and position of your screen, the location of a suitable power outlet, as well as the location and distance between the projector and the rest of your equipment.

Your projector is designed to be installed in one of the following possible installation locations:

1.Front Table

Select this location with the projector placed near the floor in front of the screen. This is the most common way to position the projector for quick setup and portability.

2.Front Ceiling

Select this location with the projector suspended upside-down from the ceiling in front of the screen.

Purchase the projector ceiling mount kit from your dealer to mount your projector on the ceiling.

Set Front Ceiling in the SYSTEM > Projector Position menu after you turn the projector on.

3.Rear Ceiling

Select this location with the projector suspended upside-down from the ceiling behind the screen.

Note that a special rear projection screen and the projector ceiling mounting kit are required for this installation location.

Set Rear Ceiling in the SYSTEM > Projector Position menu after you turn the projector on.

4.Rear Table

Select this location with the projector placed near the floor behind the screen.

Note that a special rear projection screen is required.

Set Rear Table in the SYSTEM > Projector Position menu after you turn the projector on.

9

Projection dimensions

The "screen" mentioned below refers to the projection screen usually consisting of a screen surface and a support structure.

Please see "Projector specifications" on page 65 for the native display resolution of this projector.

PA500S/PA503S/PA500X/PA503X

4:3 image on a 4:3 screen

(b)

(a)

(d)

(c)

(f)

(e)

4:3 image on a 16:10 screen

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

(e): Screen

 

 

(f): Center of lens

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

4:3 image on a 4:3 Screen

 

 

 

 

 

 

 

 

 

 

(a) Screen Size

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

(b) Projection distance

 

(c) Image

 

 

 

 

 

 

 

(d) Vertical offset

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

min.

 

max.

 

height

 

 

 

 

 

 

min.

max.

 

 

 

 

 

inch

 

mm

 

inch

 

mm

 

inch

mm

 

inch

mm

 

inch

 

mm

inch

 

mm

 

 

 

60

 

1524

94

 

2385

 

103

2623

 

36

914

 

 

3.6

 

 

91.4

3.6

 

 

91

 

 

 

70

 

1778

110

 

2782

 

120

3060

 

42

1067

 

4.2

 

 

106.7

4.2

 

 

107

 

 

 

80

 

2032

125

 

3179

 

138

3497

 

48

1219

 

4.8

 

 

121.9

4.8

 

 

122

 

 

 

90

 

2286

141

 

3577

 

155

3935

 

54

1372

 

5.4

 

 

137.2

5.4

 

 

137

 

 

 

100

 

2540

156

 

3974

 

172

4372

 

60

1524

 

6.0

 

 

152.4

6.0

 

 

152

 

 

 

110

 

2794

172

 

4372

 

189

4809

 

66

1676

 

6.6

 

 

167.6

6.6

 

 

168

 

 

 

120

 

3048

188

 

4769

 

207

5246

 

72

1829

 

7.2

 

 

182.9

7.2

 

 

183

 

 

 

130

 

3302

203

 

5167

 

224

5683

 

78

1981

 

7.8

 

 

198.1

7.8

 

 

198

 

 

 

140

 

3556

219

 

5564

 

241

6121

 

84

2134

 

8.4

 

 

213.4

8.4

 

 

213

 

 

 

150

 

3810

235

 

5962

 

258

6558

 

90

2286

 

9.0

 

 

228.6

9.0

 

 

229

 

 

 

160

 

4064

250

 

6359

 

275

6995

 

96

2438

 

9.6

 

 

243.8

9.6

 

 

244

 

 

 

170

 

4318

266

 

6756

 

293

7432

 

102

2591

 

10.2

 

 

259.1

10.2

 

 

259

 

 

 

180

 

4572

282

 

7154

 

310

7869

 

108

2743

 

10.8

 

 

274.3

10.8

 

 

274

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

10

 

 

 

 

 

 

4:3 image on a 16:10 Screen

 

 

 

(a) Screen Size

 

 

 

 

 

 

 

(b) Projection distance

(c) Image

 

 

(d) Vertical offset

 

 

 

 

min.

max.

height

 

min.

max.

 

inch

mm

inch

 

mm

inch

mm

inch

mm

inch

 

mm

inch

 

mm

60

1524

83

 

2106

91

2317

32

808

3.2

 

81

3.2

 

81

70

1778

97

 

2457

106

2703

37

942

3.7

 

94

3.7

 

94

80

2032

111

 

2809

122

3089

42

1077

4.2

 

108

4.2

 

108

90

2286

124

 

3160

137

3476

48

1212

4.8

 

121

4.8

 

121

100

2540

138

 

3511

152

3862

53

1346

5.3

 

135

5.3

 

135

110

2794

152

 

3862

167

4248

58

1481

5.8

 

148

5.8

 

148

120

3048

166

 

4213

182

4634

64

1615

6.4

 

162

6.4

 

162

130

3302

180

 

4564

198

5020

69

1750

6.9

 

175

6.9

 

175

140

3556

194

 

4915

213

5406

74

1885

7.4

 

188

7.4

 

188

150

3810

207

 

5266

228

5793

79

2019

7.9

 

202

7.9

 

202

160

4064

221

 

5617

243

6179

85

2154

8.5

 

215

8.5

 

215

170

4318

235

 

5968

258

6565

90

2289

9.0

 

229

9.0

 

229

180

4572

249

 

6319

274

6951

95

2423

9.5

 

242

9.5

 

242

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

PA503W

16:10 image on a 16:10 screen

(b)

(a)

(d)

(c)

(f)

(e)

16:10 image on a 4:3 screen

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

(e): Screen

(f): Center of lens

 

 

 

11

 

 

 

 

 

 

16:10 image on a 16:10 Screen

 

 

 

(a) Screen Size

 

 

 

 

 

 

 

(b) Projection distance

(c) Image

 

 

(d) Vertical offset

 

 

 

 

min.

max.

height

 

min.

max.

 

inch

mm

inch

 

mm

inch

mm

inch

mm

inch

 

mm

inch

 

mm

60

1524

79

 

2000

87

2200

32

808

0.0

 

0

0.0

 

0

70

1778

92

 

2333

101

2567

37

942

0.0

 

0

0.0

 

0

80

2032

105

 

2667

115

2933

42

1077

0.0

 

0

0.0

 

0

90

2286

118

 

3000

130

3300

48

1212

0.0

 

0

0.0

 

0

100

2540

131

 

3333

144

3667

53

1346

0.0

 

0

0.0

 

0

110

2794

144

 

3667

159

4033

58

1481

0.0

 

0

0.0

 

0

120

3048

157

 

4000

173

4400

64

1615

0.0

 

0

0.0

 

0

130

3302

171

 

4333

188

4767

69

1750

0.0

 

0

0.0

 

0

140

3556

184

 

4667

202

5133

74

1885

0.0

 

0

0.0

 

0

150

3810

197

 

5000

217

5500

79

2019

0.0

 

0

0.0

 

0

160

4064

210

 

5333

231

5867

85

2154

0.0

 

0

0.0

 

0

170

4318

223

 

5667

245

6233

90

2289

0.0

 

0

0.0

 

0

180

4572

236

 

6000

260

6600

95

2423

0.0

 

0

0.0

 

0

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

16:10 image on a 4:3 Screen

 

 

 

(a) Screen Size

 

 

 

 

 

 

(b) Projection distance

(c) Image

 

 

(d) Vertical offset

 

 

 

 

 

 

height

 

 

 

 

 

 

 

min.

max.

 

min.

max.

 

inch

mm

inch

 

mm

inch

mm

inch

mm

inch

 

mm

inch

 

mm

60

1524

74

 

1887

82

2075

30

762

0.0

 

0

0.0

 

0

70

1778

87

 

2201

95

2421

35

889

0.0

 

0

0.0

 

0

80

2032

99

 

2516

109

2767

40

1016

0.0

 

0

0.0

 

0

90

2286

111

 

2830

123

3113

45

1143

0.0

 

0

0.0

 

0

100

2540

124

 

3145

136

3459

50

1270

0.0

 

0

0.0

 

0

110

2794

136

 

3459

150

3805

55

1397

0.0

 

0

0.0

 

0

120

3048

149

 

3774

163

4151

60

1524

0.0

 

0

0.0

 

0

130

3302

161

 

4088

177

4497

65

1651

0.0

 

0

0.0

 

0

140

3556

173

 

4403

191

4843

70

1778

0.0

 

0

0.0

 

0

150

3810

186

 

4717

204

5189

75

1905

0.0

 

0

0.0

 

0

160

4064

198

 

5031

218

5535

80

2032

0.0

 

0

0.0

 

0

170

4318

210

 

5346

232

5881

85

2159

0.0

 

0

0.0

 

0

180

4572

223

 

5660

245

6226

90

2286

0.0

 

0

0.0

 

0

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

There is 3% tolerance among these numbers due to optical component variations. It is recommended that if you intend to permanently install the projector, you should physically test the projection size and distance using the actual projector in situ before you permanently install it, so as to make allowance for this projector's optical characteristics. This will help you determine the exact mounting position so that it best suits your installation location.

12

Connection

When connecting a signal source to the projector, be sure to:

1.Turn all equipment off before making any connections.

2.Use the correct signal cables for each source.

3.Ensure the cables are firmly inserted.

In the connections shown below, some cables may not be included with the projector (see "Shipping contents" on page 4). They are commercially available from electronics stores.

The connection illustrations below are for reference only. The connecting jacks available on the projector vary with each projector model.

For detailed connection methods, see pages 14-16.

Below is the connection method for each connector that you may find on your projector.

HDMI

HDMI cable

connector

 

Computer

(for selected models)

or

 

A/V device

 

Mini USB

USB cable

 

 

 

socket

 

Computer

 

 

RS232

RS232 cable

 

 

 

 

 

Computer

Computer

VGA cable

 

 

 

In

or

Computer

 

 

Component Video to VGA

A/V device

(D-Sub) adapter cable

 

13

Computer

VGA cable

 

 

 

Out

or

 

 

VGA to DVI-A cable

Monitor

 

 

Audio

Audio cable

 

in

or

Computer

 

Audio cable

(for Component signal)

 

 

 

 

A/V device

Video

Video cable

(for selected models)

A/V device

 

connector

 

 

 

Audio Out

Speakers

Connecting a computer or monitor

Connecting a computer

1.Take the supplied VGA cable and connect one end to the D-Sub output socket of the computer.

2.Connect the other end of the VGA cable to the Computer 1 or Computer 2 signal input socket on the projector.

3.If you wish to use the remote mouse control function, take a USB cable and connect the larger end to the USB port of the computer, and smaller end to the Mini USB socket on the projector. See "Using the remote PgUp/PgDn function" on page 7 for details.

Many notebooks do not turn on their external video ports when connected to a projector. Usually a key combo like FN + F3 or CRT/LCD key turns the external display on/off. Locate a function key labeled CRT/LCD or a function key with a monitor symbol on the notebook. Press FN and the labeled function key simultaneously. Refer to your notebook's documentation to find your notebook's key combination.

Connecting a monitor

If you want to view your presentation close-up on a monitor as well as on the screen, you can connect the Monitor Out signal output socket on the projector to an external monitor with a VGA cable following the instructions below:

14

1.Connect the projector to a computer as described in "Connecting a computer" on page 14.

2.Take a suitable VGA cable (only one supplied) and connect one end of the cable to the D-Sub input socket of the video monitor.

Or if your monitor is equipped with a DVI input socket, take a VGA to DVI-A cable and connect the DVI end of the cable to the DVI input socket of the video monitor.

3.Connect the other end of the cable to the Monitor Out socket on the projector.

The Monitor Out output only works when Computer 1 connection is made to the projector. To use this connection method in the standby mode, turn on the Active VGA Out function under the POWER MANAGEMENT > Standby Settings menu.

Connecting Video source devices

You can connect your projector to various Video source devices that provide any one of the following output sockets:

HDMI

Component Video

Video (composite)

You need only connect the projector to a Video source device using just one of the above connecting methods, however each provides a different level of video quality. The method you choose will most likely depend upon the availability of matching terminals on both the projector and the Video source device as described below:

Best video quality

The best available video connection method is HDMI. If your source device is equipped with an HDMI socket, you can enjoy uncompressed digital video quality.

See "Connecting an HDMI device" on page 15 for how to connect the projector to an HDMI source device and other details.

If no HDMI source is available, the next best video signal is Component video (not to be confused with composite video). Digital TV tuner and DVD players output Component video natively, so if available on your devices, this should be your connection method of choice in preference to (composite) video.

See "Connecting a Component Video source device" on page 16 for how to connect the projector to a component video device.

Least video quality

Composite Video is an analog video and will result in a perfectly acceptable, but less than optimal result from your projector, being the least video quality of the available methods described here.

See "Connecting a composite Video source device" on page 16 for how to connect the projector to a composite Video device.

Connecting audio

You can make use of the projector speaker in your presentations, and also connect separate amplified speakers to the Audio Out socket of the projector. The audio output is controlled by the projector Volume and Mute settings.

Connecting an HDMI device

You should use an HDMI cable when making connection between the projector and HDMI devices.

15

1.Take an HDMI cable and connect one end to the HDMI output port of the video device.

2.Connect the other end of the cable to the HDMI input port on the projector.

In the unlikely event that you connect the projector to a DVD player via the projector’s HDMI input and the projected picture displays wrong colors, please change the color space to YUV. See "Changing HDMI input settings" on page 21 for details.

Connecting a Component Video source device

Examine your Video source device to determine if it has a set of unused Component Video output sockets available:

If so, you can continue with this procedure.

If not, you will need to reassess which method you can use to connect to the device.

1.Take a VGA (D-Sub)-Component adaptor cable and connect the end with 3 RCA type connectors to the Component Video output sockets of the Video source device. Match the color of the plugs to the color of the sockets; green to green, blue to blue, and red to red.

2.Connect the other end of the VGA (D-Sub)-Component adaptor cable (with a D-Sub type connector) to the Computer 1 or Computer 2 socket on the projector.

If the selected video image is not displayed after the projector is turned on and the correct video source has been selected, check that the Video source device is turned on and operating correctly. Also check that the signal cables have been connected correctly.

VGA-Component adapter

(ViewSonic P/N: CB-00008906)

Connecting a composite Video source device

Examine your Video source device to determine if it has a set of unused composite Video output sockets available:

If so, you can continue with this procedure.

If not, you will need to reassess which method you can use to connect to the device.

1.Take a Video cable and connect one end to the composite Video output socket of the Video source device.

2.Connect the other end of the Video cable to the Video socket on the projector.

If the selected video image is not displayed after the projector is turned on and the correct video source has been selected, check that the Video source device is turned on and operating correctly. Also check that the signal cables have been connected correctly.

You need only connect to this device using a composite Video connection if Component Video input is unavailable for use. See "Connecting Video source devices" on page 15 for details.

Playing sound through the projector

You can make use of the projector speaker in your presentations, and also connect separate amplified speakers to the Audio Out socket of the projector.

16

Operation

Starting up the projector

1.Plug the power cord into the projector and into a

wall socket. Turn on the wall socket switch

(where fitted).

2. Press Power to start the projector. As soon as the lamp lights up, a "Power On Ring Tone" will

be heard. The Power indicator light stays blue when the projector is on.

(If necessary) Rotate the focus ring to adjust the image clearness.

If the projector is still hot from previous activity, it will run the cooling fan for approximately 90 seconds before energizing the lamp.

To maintain the lamp life, once you turn the projector on, wait at least 5 minutes before turning it off.

To turn off the ring tone, see "Turning off the Power On/Off Ring Tone" on page 31 for details.

3.If the projector is activated for the first time, select your OSD language following the on-screen instructions.

4.Switch all of the connected equipment on.

5.The projector will start to search for input signals. The current input signal being scanned appears in the upper left corner of the screen. If the projector doesn't detect a valid signal, the message 'No Signal' will continue to be displayed until an input signal is found.

You can also press Source to select your desired input signal. See "Switching input signal" on page 21 for details.

If the frequency/resolution of the input signal exceeds the projector's operating range, you will see the message 'Out of Range' displayed on a blank screen. Please change to an input signal which is compatible with the projector's resolution or set the input signal to a lower setting.

See "Timing chart" on page 61 for details.

17

ViewSonic PA503X, PA503W, PA503S User Manual

Using the menus

The projector is equipped with On-Screen Display (OSD) menus for making various adjustments and settings.

The OSD screenshots below are for reference only, and may differ from the actual design.

Below is the overview of the OSD menu.

Main menu icon

Highlight

Sub-menu

Current input signal

To use the OSD menus, please select your language first.

Status

Go to the previous page or to exit.

1.Press Menu to turn the OSD menu on.

3.Press to highlight Language and press Enter.

2.Use / to highlight the

SYSTEM menu.

4.Use / / / to select a preferred language.

5.Press Enter to go back to main menu and press Menu to leave the OSD menu.

18

Utilizing the password function

For security purposes and to help prevent unauthorized use, the projector includes an option for setting up password security. The password can be set through the On-Screen Display (OSD) menu. For details of the OSD menu operation, please refer to "Using the menus" on page 18.

You will be inconvenienced if you enable the password function yet forget the password somehow. Do make a note of your password, and keep the note in a safe place for later recall.

Setting a password

Once a password has been set and the power on lock is enabled, the projector cannot be used unless the correct password is entered every time the projector is started.

1.Open the OSD menu and go to the SYSTEM > Security Settings menu.

2.Press Enter and the Security Settings page is displayed.

3.Highlight Power On Lock and select On by pressing /.

4.As pictured to the right, the four arrow keys

( , , , ) respectively represent 4 digits (1, 2, 3, 4). According to the password you desire to set, press the arrow keys to enter six digits for the password.

5.Confirm the new password by re-entering the new password.

Once the password is set, the OSD menu returns to the Security Settings page.

6.To leave the OSD menu, press Exit.

If you forget the password

If the password function is activated, you will be asked to enter the six-digit password every time you turn on the projector. If you enter the wrong password, the password error message as pictured to the right is displayed lasting for 5 seconds, and the message 'INPUT PASSWORD' follows. You can retry by

entering another six-digit password, or if you did not record the password in this user manual, and you absolutely do not remember it, you can use the password recall procedure. See "Entering the password recall procedure" on page 20 for details.

If you enter an incorrect password 5 times in succession, the projector will automatically shut down in a short time.

19

Loading...
+ 53 hidden pages