Velodyne Acoustics SPL-800, SPL-1000, and SPL-1200 User Manual

0 (0)
Home Theater Subwoofer
SPL-800, SPL-1000,
and SPL-1200
Series II
Owner's Manual
Caution: To reduce the risk of electric shock, do not remove cover (or back). No user-serviceable
parts inside. Refer servicing to qualified service personnel.
The lighting flash with arrowhead symbol is intended to alert the user to the presence of uninsulated
of electric shock to persons.
The exclamation point symbol is intended to alert the user to the presence of important operating and
maintenance (servicing) instructions in the literature accompanying the subwoofer.
1. Read Instructions -- All safety and operating instructions should be read before the subwoofer is operated.
2. Retain Instructions -- The safety and operating instructions should be retained for future reference.
3. Heed Warnings -- All warnings on the subwoofer and in the operating instructions should be adhered to.
4. Follow Instructions -- All operating and use instructions should be followed.
5. Water and Moisture -- The subwoofer should
not
be used near water -- for example, near a bathtub, washbowl,
kitchen sink, laundry tub, in a wet basement, near a swimming pool, or the like.
6. Carts and Stands -- The subwoofer should be used only with a cart or stand recommended by the manufacturer
to avoid injury from tipover.
7. Wall or Ceiling Mounting -- The subwoofer should be mounted to a wall or ceiling only as recommended by
the manufacturer.
8. Ventilation -- The subwoofer should be situated so that its location or position does not interfere with its proper
ventilation. For example, the subwoofer should not be situated on a bed, sofa, rug, or similar surface that
may block the ventilation openings; or placed in a built-in installation such as a bookcase or cabinet that may
impede the flow of air through the ventilation openings.
9. Heat -- The subwoofer should be situated away from heat sources such as radiators, heat registers, stoves,
or other subwoofers that produce heat.
10. Power Sources -- The subwoofer should be connected to a power supply only of the type described in the
operating instructions or as marked on the subwoofer.
11. Power-Cord Protection -- Power-supply cords should be routed so that they are not likely to be walked on
or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience
receptacles, and the point at which they exit from the subwoofer.
12. Caution: To prevent electrical shock, match wide blade of plug to wide slot, fully inserted.
13. Cleaning -- The subwoofer should be cleaned only as recommended by the manufacturer.
14. Nonuse Periods -- The power cord of the subwoofer should be unplugged from the outlet when left unused for
a long period of time.
15. Object and Liquid Entry -- Care should be taken so that objects do not fall and liquids are not spilled onto the
enclosure.
16. Damage Requiring Service -- The subwoofer should be serviced by qualified service personnel when:
a. The power-supply cord or plug has been damaged.
b. Objects have fallen or liquid has been spilled into the subwoofer.
c. The subwoofer has been exposed to rain.
d. The subwoofer does not appear to operate normally or exhibits a marked change in performance.
e. The subwoofer has been dropped or damaged.
17. Servicing -- The user should not attempt to service the subwoofer beyond what is described in the operating
instructions.
18. Overloading -- Do not overload wall outlets, extension cords, or integral convenience receptacles as this can
result in a risk of fire or electric shock.
19. Replacement parts -- When replacement parts are required, be sure the service technician has used replacement
parts specified by the manufacturer or have the same characteristics as the original part. Unauthorized
substitutions may result in fire, electric shock, or other hazards.
20. Safety Check -- Upon completion of any service or service of repairs to this product, ask the service technician
to perform safety checks to determine that the product is in proper operating condition.
All other servicing should be referred to qualified service personnel.
IMPORTANT SAFETY INSTRUCTIONS
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
1
Vorsicht: Zur Vermeidung von Gefahr durch elektrischen Schlag, Deckel (oder Rückwand) nicht
abnehmen. Produkt enthält keine Anwenderteile. Reparatur und Wartung nur von qualifiziertem
Fachpersonal vornehmen lassen.
Das Blitzsymbol dient als Hinweis auf unisolierte „gefährliche Spannungen“ innerhalb des Gehäuses,
deren Werte eine Berührungsgefahr für den Menschen darstellen können.
Das Symbol mit dem Ausrufungszeichen dient als Hinweis auf wichtige, in den Unterlagen des Subwoofers
enthaltene Bedienungs- und Wartungsvorschriften.
1. Anleitungen lesen - Alle Sicherheits- und Bedienungsanleitungen vor Inbetriebnahme des Subwoofers aufmerksam
durchlesen.
2. Anleitungen aufbewahren - Die Sicherheits- und Bedienungsanleitungen zur späteren Bezugnahme aufbewahren.
3. Warnungen beachten - Alle Warnungen am Subwoofer und in der Bedienungsanleitung unbedingt beachten.
4. Anleitungen befolgen - Alle Bedienungs- und Gebrauchsanleitungen genau befolgen.
5. Wasser und Feuchtigkeit - Subwoofer nicht in der Nähe von Wasser aufstellen, d.h. neben einer Badewanne,
Spüle, Waschmaschine, in einem feuchten Keller, in der Nähe des Swimmingpools o.ä..
6. Rollwagen und Ständer - Subwoofer nur mit einem vom Hersteller empfohlenen Rollwagen oder Ständer benutzen.
7. Wand- oder Deckenbefestigung - Subwoofer nur den Herstellerempfehlungen gemäß an der Wand oder Decke
befestigen.
8. Belüftung - Subwoofer so aufstellen, daß die erforderliche Belüftung nicht behindert wird. D .h., Subwoofer nicht auf
einer weichen Oberfläche wie einem Bett, Sofa, Teppich o.ä. aufstellen, die die Belüftungsöffnungen blockieren
kann. Subwoofer gleichfalls nicht in einem Regal oder Schrank unterbringen, worin die Luftzufuhr behindert wird.
9. Wärme - Subwoofer nicht in der Nähe von Wärmequellen, wie Heizkörpern, Wärmespeichern, Öfen oder anderen
wärmeerzeugenden Subwoofern aufstellen.
10. Netzanschluß - Subwoofer nur an eine der in der Bedienungsanleitung beschriebenen oder auf dem Subwoofer
angegebenen Stromquellen anschließen.
11. Netzkabelschutz - Netzkabel so verlegen, daß nicht daraufgetreten wird oder sie durch darauf-oder
dagegengestellte Gegenstände eingeklemmt werden können. Die Anschlußstellen des Netzkabels an Steckdosen
und am Subwoofer dabei besonders beachten.
12. „Vorsicht“: Zur Vermeidung von Gefahr durch elektrischen Schlag sicherstellen, daß der Schutzkontakt
des Steckers vollständig in die Steckdose eingeführt ist.
13. Reinigung - Subwoofer nur den Herstellerempfehlungen gemäß reinigen.
14. Betriebsfreie Zeiträume - Netzkabel des Subwoofers aus der Steckdose ziehen, wenn er über einen längeren
Zeitraum nicht benutzt wird.
15. Beschädigungen durch Gegenstände oder Flüssigkeiten - Es ist darauf zu achten, daß keine Gegenstände auf
das Gehäuse fallen oder Flüssigkeiten darauf verschüttet werden.
16. Beschädigungen, die eine Reparatur erforderlich machen - Subwoofer sollte von qualifiziertem Fachpersonal
repariert werden, wenn:
a. Das Netzkabel oder der Stecker beschädigt sind.
b. Gegenstände oder Flüssigkeiten in den Subwoofer gelangt sind.
c. Der Subwoofer dem Regen ausgesetzt wurde.
d. Der Betrieb des Subwoofers gestört ist oder seine Leistung deutlich nachgelassen hat.
e. Der Subwoofer fallengelassen oder beschädigt wurde.
17. Reparatur und Wartung - Durch den Benutzer auszuführende Wartungsmaßnahmen des Subwoofers sind auf die
in der Bedienungsanleitung angegebenen Prozeduren beschränkt.
18. Überlastung - Zur Vermeidung von Brandgefahr und elektrischem Schlag Wandsteckdosen,
Verlängerungskabel bzw . eingebaute Steckdosen nicht überlasten.
19. Ersatzteile - Wenn Ersatzteile benötigt werden, sicherstellen, daß der Servicetechniker entweder die vom
Hersteller angegebenen Ersatzteile benutzt oder Teile, die den Originalteilen entsprechende Kennwerte
besitzen. Die Verwendung von Ersatzteilen, die nicht zugelassen sind, kann Brände, elektrischen Schlag
oder andere Gefahren verursachen.
20. Sicherheitsprüfung - Nach Beendigung von Wartungs- oder Reparaturmaßnahmen an diesem Produkt vom
Servicetechniker Sicherheitsprüfungen zum Nachweis des ordnungsgemäßen Betriebszustandes vornehmen
lassen.
Alle anderweitigen Servicemaßnahmen von qualifiziertem Wartungspersonal durchführen lassen.
2
WICHTIGE SICHERHEITSHINWEISE
VORSICHT
GEFÄHRLICHE SPANNUNG
NICHT ÖFFNEN
Attention: Afin d’éviter tout risque d’électrocution, ne pas enlever le boitier (ou partie arrière de
l’enceinte). A ucune pièce ne doit être manipulée par l’utilisateur . P our tout entretien, v ous référer à un
personnel de service qualifié.
Le symbol de l’éclair avec la flèche sert à avertir l’utilisateur de la présence d’un “voltage dangereux”
non isolé dans l’enceinte du produit d’une magnitude pouvant constituer un risque
d’électrocution de personnes.
Le symbol du point d’exclamation sert à avertir l’utilisateur que d’importants conseils de fonctionnement
et de maintenance (entretien) sont fournis avec l’enceinte d’extrêmes graves.
1. Lire le mode d’emploi - Tous les conseils de sécurité et de fonctionnement doivent être lus avant de mettre en
marche l’enceinte.
2. Garder le mode d’emploi - Il est conseillé de conserver les conseils de sécurité et de fonctionnement pour un
éventuel usage futur.
3. Avertissements - Il est important de se conformer à tous les conseils de fonctionnement concernant l’enceinte
et à toutes les instructions inscrites sur l’enceinte.
4. Suivre les conseils - Tous les conseils d’utilisation et de fonctionnement doivent être suivis à la règle.
5. Eau et humidité - Ne pas utiliser l’enceinte près d’une source d’eau - par exemple, près de la baignoire, d’une
bassine de lavage, d’un évier de cuisine, d’un bac à lavage, dans un sous-seul mouillé, près d’une piscine…
6. Pieds et Supports - N’utiliser que des pieds et supports recommandés par le fabricant.
7. Assemblage mural ou au plafond - Se conformer uniquement aux instructions du fabricant pour fixer l’enceinte
sur un mur ou sur un plafond.
8. Ventilation - Il est important de placer l’enceinte de telle sorte qu’elle ne gêne pas sa propre ventilation. Par
exemple, ne pas placer l’enceinte sur un lit, un canapé, sur la moquette, ou sur toute surface similaire qui
bloque les ouvertures de ventilation ; ne pas poser l’enceinte dans une meuble encastré ou fermé telle qu’une
bibliothèque ou un meuble qui empêche l’air de circuler par les ouvertures de ventilation de l’enceinte.
9. Chaleur - Placer l’enceinte loin de toute source de chaleur tels que radiateurs, compteurs thermiques, fours ou
autres enceintes dégageant de la chaleur.
10. Sources d’électricité - Ne brancher l’enceinte que dans une prise du type décrit dans le mode d’emploi ou
comme indiqué par le fabricant.
11 . Protection du cordon électrique - Les cordons électriques doivent être fixés pour éviter que toute personne ne
marche dessus et que rien ne puisse être placé sur ou contre eux - faire tout particulièrement attention aux
cordons branchés dans des prises électriques, à des réceptacles et à leurs points de sorties de l’enceinte.
12. ”Attention : Afin d’éviter tout choc électrique, introduire la lame la plus large de la fiche dans la borne
correspondante de la prise et pousser jusqu’au fond”.
13. Nettoyage - Pour le nettoyage de l’enceinte, suivre scrupuleusement les instructions du fabricant.
14. Périodes de non-utilisation - Le cordon électrique de l’enceinte doit rester débranché si l’enceinte reste
inutilisée pendant une longue période de temps.
15 . Infiltration d’objet ou de liquide - Faire attention à ce qu’aucun objet ne tombe et à ce qu’aucun liquide ne soit
versé sur l’enceinte.
16 . Dommages nécessitant réparation - L’enceinte ne doit être réparée que par du personnel qualifié lorsque :
a. le cordon électrique ou la prise ont été endommagés.
b. Des objets sont tombés ou du liquide a été versé sur l’enceinte.
c. L’enceinte a été exposée à la pluie.
d. L’enceinte ne semble pas fonctionner normalement ou indique un changement de performance.
e. L’enceinte est tombée par terre ou a été endommagée.
17. Entretien - L’utilisateur ne doit pas tenter de réparer l’enceinte au-delà de ce qui est décrit dans le mode
d’emploi.
18. Surcharge - Ne pas surcharger les prises murales, les rallonges, ou les prises femelles encastrées de
commodité. On risquerait un incendie ou un choc électrique.
19. Pièces de rechange - Lorsque le remplacement d’une pièce s’avère nécessaire, s’assurer que le technicien
utilise la pièce spécifiée par le fabriquant, ou une pièce possédant les mêmes caractéristiques que la pièce
d’origine. Les substitutions non autorisées peuvent provoquer des incendies ou des chocs électriques, ou
présenter d’autres dangers.
20. Contrôle de sécurité - Après toute intervention technique sur ce produit (neuf ou réparé), demander au
technicien de procéder à un contrôle de sécurité pour vérifier qu’il est en bon état de marche.
Toute autre réparation doit être référée à du personnel qualifié.
3
IMPORTANTES CONSIGNES DE SECURITE
ATTENTION
Risque d’électrocution
Ne pas ouvrir
continued. . .
Congratulations!
Congratulations on your purchase of a Velodyne subwoofer system. This
system represents the state of the art in home audio reproduction and will
provide you with years of listening pleasure when properly cared for. Read
and follow this instruction manual to insure safe and proper system
connection and operation.
Caution!
Please observe the following instructions to insure safe and proper system
operation.
Note: Do not leave unit in direct sunlight or use in high humidity
environments!!!
Warning!
To prevent fire or shock hazard, do not expose this equipment to rain or
moisture. To avoid electrical shock, do not open speaker enclosure or amp
chassis cover. Please observe all warnings on the equipment itself. There
are no user serviceable parts inside. Please refer all service questions to
your authorized Velodyne dealer.
Prior to installation-
Please unpack the system carefully. This unit is heavy. Use caution when
lifting or moving to avoid injury. Remove all staples used to seal the carton
as they can scratch the cabinet. Please save the carton and all packaging
materials for future use. Packing this unit in any other carton may result
in severe damage when shipping. Record the serial number in the space
provided on the warranty card or log onto www.velodyne.com.
4
• Signal sensing auto turn on/off (defeatable)
• Variable volume control
• Selectable phase control (0
°
or 180
°
)
• Frequency response of 28 - 120 Hz (SPL-800 Series II), 24 - 120Hz (SPL-
1000 Series II), 22-120Hz (SPL-1200 Series II)
• Magnetically shielded for video use (SPL-1000 Series II and SPL-1200
Series II)
• Multiple staggered low-pass crossovers; 12dB/octave initial, 48dB/
octave ultimate
• Driver Displacement Control circuit prevents over excursion and amp
clipping
• Blue power indicator LED
• High-excursion EPDM rubber surround
• Oversized spider for linearity at high excursion
Prepare for Installation
Your new Velodyne subwoofer provides for a number of installation
options. Read all the installation information below in order to determine
which installation option is best for your system. Remember to perform
all installation procedures with system power turned off to prevent
possible damage.

Placement

True subwoofers operate at extremely low frequencies which are primarily
omni-directional. While it is recommended that the subwoofer be placed
on the same plane as the satellite speakers, room and system conditions
often dictate otherwise. Keep in mind that frequency response and output
level can be drastically influenced by placement, depending on the
acoustic properties of the listening room. Typically, the optimum location
continued. . .
5
Product Features
• 8" (6.5" piston diameter) subwoofer with 2.5" high-temp voice coil and
107 ounce magnet/204 ounce motor structure; 10" (8" piston diameter)
or 12" (9.7" piston diameter) subwoofer with 3" voice coil and 162 ounce
magnet/346 ounce motor structure
• Built-in 2000 watts Dynamic/1000 watts RMS high efficiency class D
amplifier
• Adjustable (40 to 120Hz) low-pass crossover (defeatable)
• Line-level (RCA) inputs and outputs
• Speaker-level inputs with 5 way binding post connections
continued. . .
Regardless of where you install your Velodyne subwoofer, it must remain
in an upright position (woofer facing forward). Using, shipping, or
otherwise storing the subwoofer in any other position for an extended
period of time may result in damage to the unit not covered by warranty.
The SPL-1000 Series II and SPL-1200 Series II are magnetically shielded to
reduce the amount of stray magnetic energy emitted from the speaker's
motor structure. This greatly increases flexibility when placing the unit
close to video monitors as there is very little stray magnetism. Certain types
of televisions are particularly sensitive to stray magnetic fields. If your
television produces distorted colors after installing your subwoofer,
simply increase the distance between your television and the subwoofer,
until normal color and operation is returned.
Your new Velodyne subwoofer, like any good speaker system, requires
proper positioning within the listening space to provide maximum
performance. Improperly placed speakers may degrade the sound quality
and reduce your listening pleasure. Depending on the size and type of
furnishings in the room, perfect placement may not be possible. Finding
the best location for your environment will likely require some
experimentation. We suggest you experiment with the location during
setup to find what sounds best to you when seated in your typical listening
position.
6
for a subwoofer is tucked away in a corner of your listening room. This
location will usually offer the greatest output levels and optimum low
frequency extension. The worst location for a subwoofer is typically far
away from any walls, and close to the center of your room. Avoid these
locations when possible. When using a pair of Velodyne subwoofers in
stereo, it is preferable to place each subwoofer by the satellite of the same
channel.
Caution! This subwoofer has electronics built into the cabinet. Do not
place the cabinet next to sources of heat such as furnace registers,
radiators, etc. Do not place the unit near sources of excessive moisture,
such as evaporative coolers, humidifiers, etc. The power cord should be
routed in such a way that it will not be walked on, pinched, or compressed
in any way that could result in damaging the insulation or wire.
Loading...
+ 15 hidden pages