7" ANGLE SANDER
PLEASE READ AND FOLLOW ALL WARNINGS
Read Operating Instructions
Always become familiar with all the
instructions and warnings before
operating any power tool.
Always Wear Approved
Eye Protection
Impact resistant eye protection
should meet or exceed the
standards as set forth in the United
States ANSI Z87.1, Occupational
and Educational Eye and Face
Protection. Look for the marking
Z87.1 on your eye protection to
insure that it is an approved style.
For further information, ANSI Z87.1,
Occupational and Educational Eye
and Face Protection, is available
from the American National
Standards Institute, Inc., 11 West
42nd Street, New York, NY 10036.
Hearing Protection is
Recommended
Hearing protection should be used
when the noise level exposure
equals or exceeds an 8 hour timeweighted average sound level of 85
dBA. Process noise, reflective
surfaces, other tools being
operated nearby, all add to the
noise level present in your work
area. If you are unable to determine
your noise level exposure, we
recommend the use of hearing
protection.
Avoid Prolonged Exposure to
Vibration
Tools can vibrate during use.
Prolonged exposure to vibration or
very repetitive hand and arm
movements, can cause injury.
Stop using any tool if discomfort,
tingling feeling or pain occurs. You
should consult your physician
before resuming use of the tool.
90 PSIG Maximum
This tool is designed to operate at
an air pressure of 90 pounds per
square inch gauge pressure (90
PSIG) maximum, at the tool. Use of
higher air pressure can, and may
cause injury. Also, the use of higher
air pressure places the internal
components under loads and
stresses they were not designed for,
causing premature failure. The air
supply should be clean and dry,
preferably lubricated. For best results,
drain the moisture from your
compressor daily.
Universal Tool
A Division of Florida Pneumatic Manufacturing Corporation
851 Jupiter Park Lane, Jupiter, Florida 33458
Toll Free 1-800-327-9403
Read these instructions carefully before attempting to install, operate
or service this Florida Pneumatic product. Failure to comply with the
instructions could result in personal injury and/or property damage!
Retain these instructions for future reference.
FPMC
WARNING:
ONLY USE ACCESSORIES THAT ARE
RATED TO RUN AT THE MAXIMUM
SPEED (RPM) OR LOWER.
Some dust created by power sanding,
sawing, grinding, drilling, and other
construction activities contains chemicals
known to cause cancer, birth defects or
reproductive harm. Some examples of
these chemicals are:
• Lead from lead-based paints
• Crystalline silica from bricks, cement
and other masonry products
• Arsenic and chromium from chemically treated lumber
Your risk from these exposures varies,
depending on how often you do this type
of work. To reduce your exposure to
these chemicals, work in a well-ventilated
area and work with approved safety
equipment such as those dust masks that
are specially designed to filter out
microscopic particles.
PL0233
UT8766S
devices as furnished by the manufacturer. Where an air tool is modified or
altered, the modifier shall provide the
safeguards to enable it to be safely used
in the operations intended and to comply
with any applicable provisions as
contained in ANSI B186.1.
Tool Installation
Pressure regulators shall be used to limit
air pressure to the rated pressure where
the supply pressure exceeds the tool’s
rated pressure. Air hoses and lines shall
be relieved of compressed air before
being disconnected or disjointed, unless
there is automatic valve closing protection at the joint being separated. Synthetic lubricants which can cause
deterioration of elastomer seals shall not
be used in air systems of air tools.
Tool Maintenance
It shall be the tool owner’s and/or
employer’s responsibility to assure that
tools are maintained in a safe operating
condition. Tool maintenance and repair
shall be performed by authorized,
trained, competent personnel. Tools shall
be disconnected from their compressed
air supply before repairs are attempted.
Repairs shall be consistent with the
manufacturer’s recommended procedures. Tool, hoses and fittings shall be
replaced if unsuitable for safe operation.
It shall be the tool owner’s and/or
employer’s responsibility to keep required
rating markings and warnings on the tool
in legible condition.
Safety Instructions
The following instructions are furnished
as general guidelines for use of your
pneumatic tool. They cannot comprehensively cover all possible or conceivable uses of the subject tool. For
additional information on the safe use
of air tools, we advise you to obtain a
copy of ANSI B186.1 Safety Code for
Portable Air Tools, available from the
following source:
American National Standards
Institute, Inc.
11 West 42nd Street
New York, NY 10036.
The use of the word “shall” in the
following instructions, indicates that
adherence to the particular requirement is necessary to conform to ANSI
B186.1.
Tool Application and Usage
Portable tools shall be used only for
the purposes intended in their design
and within the capacity for which they
were intended and rated. It shall be
the tool owner’s and/or employer’s
responsibility to instruct each operator
in the safe use of the tool. Tools shall
not be used without guards and safety
Description
Universal Tool 7" angle sander has a powerful 1.7 horsepower motor and is ideal for
all sander applications. Includes a side handle for increased operator control and
rear exhaust.
Replacement Parts for UT8766S
UT8766S
UT8766S
7" ANGLE SANDER 7" ANGLE SANDER
Limited Warranty
Universal Tool warrants its tools to be free from defects in material and workmanship for one year
from the date of purchase. This warranty does not apply to tools which have been abused,
misused, modified or repaired by someone other than Universal Tool or its authorized service
centers. If a Universal Tool proves defective in material of workmanship within one year after
purchase, return it to any authorized service center or to Universal Tool, freight prepaid. Please
enclose your name, address and adequate proof of purchase date with a brief description of the
defect. Universal Tool will, at its option, repair or replace defective tools, free of charge. Repairs or
replacements are warranted as described above for the remainder of the warranty period. Universal Tool's sole liability and your exclusive remedy under this warranty is limited to repair or replacement of the defective tool. There are no other warranties expressed or implied and Universal Tool
shall not be liable for incidental, consequential or special damages, or any other damages, costs or
expense of repair or replacement as described above.
Max Wheel Size.................................................................................................................. 7"
Spindle size.................................................................................................................5/8"-11
Free speed ..........................................................................................................7,500 RPM
Weight................................................................................................................................6.6 lbs.
Length...........................................................................................................................12-1/2"
Average air consumption........................................................................................10 CFM
Recommended hose size.......................................................................................1/2" I.D.
Air inlet......................................................................................................................3/8" NPT
Maximum air pressure...............................................................................................90 psi
Parts Breakdown for UT8766S
Specifications
NO PART NO DESCRIPTION
1 987001 REGULATOR
2-1 9OB-02 O-RING
2-2 9288303 O-RING
3 987003 INLET BUSHING
4 987004 HOUSING COVER
5 987005 CLAMP NUT
6 987006 WASHER
7 987007 SPRING
8 987008 VALVE
9 987009 WASHER
10 9OB-04 O-RING
11 9288306 VALVE STEM
12 9OB-03 SNAP RING
13 987013 HOUSING
14 987014 SNAP RING
15 987015 SPRING
16 987016 LEVER PIN
17 987017 LEVER
18 987018 PIN
19 987019 WASHER
20 987020 SPRING HOLDER
21 987021 WASHER
22 987022 SPRING
23 987023 GOVERNOR VALVE
24 987024 PIN
25 987025 GOVERNOR WEIGHT (2)
26 987026 GOVERNOR PIN (2)
27 987027 GOVERNOR CAGE
28 987028 WASHER
29 987029 BEARING (2)
NO PART NO DESCRIPTION
30 987030 REAR PLATE
31 987031 ROTOR BLABE (4)
32 987032 ROTOR
33 981326 PIN (2)
34 987034 CYLINDER
35 987035 FRONT PLATE
36 9870408 BEARING
37 987037 BEVEL GEAR
38 987038 SILENCER
39 987039 ANGLE HOUSING
40 9870011 O-RING (2)
41 987041 SILENCER (2)
42 9AGD100-22 EXHAUT SLEEVE (2)
43 987043 SCREW (2)
44 987044 HANDLE
45 987045 SPACER
46 987046 BEARING
47 987047 RETAINING RING
48 987048 BEVEL GEAR
49 987049 BEARING (2)
50 987050 KEY
51 987051 SHAFT
52 987052 FACE PLATE
53 9870S53 DISC NUT
54 92HG4-32 SCREW (7)
55 987055 DISC NUT
56 987056 STOP SPANNER
57 987057 DISC SPANNER
58 987058 SNAP RING
59 987059 STAINLESS MESH (2)
60 9870S60 BACKING PAD
Loading...