Operating Manual
For Easy Clicker
UR2-211
1 Introduction |
3 Button Functions |
|
This remote control is designed to operate most Digital, Analog Cable boxes, IPTV set top boxes and TVs.
2 Replacing Batteries
Before you program or operate the remote control, you must install two new AA alkaline batteries.
STEP1 Remove the battery compartment cover from the backofyourremotecontrol.
STEP2 Check battery polarity carefully, and install the batteries as shown in the illustration below.
STEP3 Replace the battery compartment cover.
Macro Button
For future use
Universal Remote Control, Inc.
www.universalremote.com
OCE-0082E Rev 08 (14/03/14)
4 Programming the Remote Control
*Note : In this section, when you are instructed to press a [DEVICE] button, that means you should press either the CBL or TV button, depending on which device you are programming the remote to operate.
A. Quick Set-Up Method
(Refer to the Section B Quick Set-up table of codes)
STEP1 Turn on the component you want to program. To program your TV, turn on the TV.
STEP2 Press and hold the [DEVICE] key for 5 seconds until the Device LED will blink once and stays on. Continue to hold the [DEVICE] key and press the number key assigned to your brand in the Quick Setup Code Table and release both [DEVICE] key and the number key to save the code. The Device LED will blink twice to confirm that the code is stored.
STEP3 Point the remote control at the component.
STEP4 Press the power button. If it turns off, it is programmed for your component. If it does not turn off, use the PreProgrammed 3-Digit code Method or Scanning Method.
Repeat the steps above for all components (CBL, TV).
B. Quick Set-up Code Tables
CBL
QuickNumber |
Manufacturer/Brand |
|
|
0 |
PACE DTA |
1 |
SA/CISCO, SAMSUNG, PACE DIGITAL |
2 |
MOTOROLA DIGITAL |
3 |
MOTOROLA DTA |
4 |
EVOLUTION DTA |
5 |
CISCO IPTV |
6 |
ADB IPTV |
7 |
TECHNICOLOR |
8 |
AMINO 140/540 IPTV |
9 |
MOTOROLA IPTV |
TV
QuickNumber |
Manufacturer/Brand |
0SANYO
1SONY
2SAMSUNG
3LG
4TOSHIBA
5PANASONIC
6PHILIPS
7HITACHI
8SHARP
9VIZIO
C.Manual Programming
Theremotecontrolcanbeprogrammed by entering a three-digit code number that corresponds to particular brands and models of equipment. The threedigit code numbers are listed in the code tables sections of this instruction manual.
STEP1 Turn on the equipment that you want the remote control to operate (Cable Box or TV).
STEP2 Press the [DEVICE] button and the [OK/SEL] button simultaneously for 3 seconds. The corresponding device LED will turn on indicating that it is ready to be programmed. The LED will remain on for 30 seconds. The next step must be entered while the LED is on.
STEP3 Point the remote control toward the equipment and enter the three-digit code number assigned to your
brand from the code tables. If there are more than one three-digit number listed for your brand, try one code number at a time until your equipment turns off.
*Note: You can verify that you have selected the correct code by pressing the [POWER] button. The equipment should turn back on. Then try all of the functions on the remote control (i.e. volume, mute, etc.) to ensure you have the correct code. If any of the functions do not operate as they should, repeat the instructions from STEP 3 above using the next three digit code number from the brand list.
STEP4 Store the three-digit code by pressing the same [DEVICE] button once again. The device LED will blink twice to confirm that the code has been stored.
D. Auto Search Method
If none of the three digit code numbers assigned to your brand of equipment works, or the code table does not list your brand, you can use the Auto Search Method to find the correct three-digit code number for your equipment by following steps:
STEP1 Turn on the equipment that you want the remote control to operate (Cable Box or TV).
STEP2 Press the [DEVICE] button and the [OK/SEL] button simultaneously for 3 seconds. The device LED will turn on indicating that it is ready to be programmed. The LED will remain on for 30 seconds. The next step must be entered while the LED is on.
STEP3 Press the [CH5] or [CH6] button one at a time or keep it pressed. The remote will emit a series of Power ON/OFF code signals. Release the [CH5] or [CH6] button as soon as the equipment turns off.
*Note: You can verify that you have selected the correct code by pressing the [POWER] button. The equipment should turn back on. Then try all of the functions on the remote control (i.e. volume, mute, etc.) to ensure you have the correct code. If any of the functions do not operate as they should, repeat the instructions from STEP 3 above to continue the Auto Search Method.
STEP4 Press the same [DEVICE]
Loading...