Operating Manual
For Easy Clicker
UR3-SR3
Universal Remote Control, Inc.
www.universalremote.com
1 Introduction
This remote control is designed to operate most Digital and Analog Cable Boxes, as well as TVs, and a DVD player.
2 Replacing Batteries
Before you program or operate the remote control, you must install two new AAA alkaline batteries.
STEP1 Remove the battery compartment cover from the back of your remote control.
STEP2 Check battery polarity carefully, and install the batteries as shown in the illustration below.
STEP3 Replace the battery compartment cover.
Install two
AAA alkaline batteries as shown here
1
3 Button Functions
4 ProgrammingtheRemoteControl.
*Note : In this section, when you are instructed to press a [DEVICE] button, that means you should press either the CBL, TV, or DVD button, depending on which device you are programming the remote to operate.
A. Quick Set-Up Method
STEP1
Turn on the component you want to program. To program your TV, turn on the TV.
STEP2
Press and hold the [DEVICE] key for 5 seconds until the Device LED will blink once and stays on. Continue to hold the [DEVICE] key and press the
2
number key assigned to your brand in the Quick Set-up Code Table and release both [DEVICE] key and the number key to save the code. The Device LED will blink twice to confirm that the code is stored.
STEP3 Point the remote control at the component.
STEP4 Press the [DEVICE] button. If it turns off, it is programmed for your component. If it does not turn off, use the Pre-Programmed 3-Digit code Method or Scanning Method.
Repeat the steps above for all components (CBL, TV, DVD).
B. Quick Set-up Code Tables
CBL |
|
Quick Number |
Manufacturer/Brand |
0PACE DTA
1SA/CISCO, SAMSUNG, PACE DIGITAL
2MOTOROLA DIGITAL
3MOTOROLA DTA
4EVOLUTION DTA
5CISCO IPTV
6ADB IPTV
7TECHNICOLOR
8AMINO 140/540 IPTV
9MOTOROLA IPTV
TV
Quick Number
0SANYO
1SONY
2SAMSUNG
3LG
4TOSHIBA
5PANASONIC
6PHILIPS
7HITACHI
8SHARP
9VIZIO
Manufacturer/Brand
3
DVD
Quick Number |
Manufacturer/Brand |
0HITACHI
1SONY
2PHILIPS
3SAMSUNG
4PHILIPS MAGNAVOX
5PANASONIC
6LG
7JVC
8DENON
9PIONEER
C.Manual Programming
The remote control can be programmed by entering a threedigit code number that corresponds to particular brands and models of equipment. The three-digit code numbers are listed in the code tables sections of this instruction manual.
STEP1 Turn on the equipment that you want the remote control to operate Cable Box, TV and DVD.
STEP2 Press the [DEVICE] button and the [OK/SEL] button simultaneously for three seconds. The corresponding device LED will turn on indicating that it is ready to be programmed. The LED will remain on for 20 seconds. The next step must be entered while the LED is on.
STEP3 Point the remote control toward the equipment and enter the three-digit code number assigned to your brand from the code tables. If there are more than one three-digit number listed for your brand, try one code number at a time until your equipment turns off.
*Note : You can verify that you have selected the correct code by pressing the [MUTE] button. The equipment should turn on or off.
STEP4 Store the three-digit code by pressing the same [DEVICE] button once again. The device LED will
4
blink twice to confirm that the code has been stored.
*Note : Try all the functions on the remote control. If any of the functions do not operate as they should, repeat the instructions from Step 2 using the next three-digit code number from the same brand list.
D. Auto Search Method
If none of the three digit code numbers assigned to your brand of equipment works, or the code table does not list your brand, you can use the Auto Search Method to find the correct three-digit code number for your equipment by following steps:
STEP1 Turn on the equipment that you want the remote control to operate (Cable Box, TV, or DVD).
STEP2 Press the [DEVICE] button and the [OK/SEL] button simultaneously for three seconds. The device LED will turn on indicating that it is ready to be programmed. The LED will remain on for 20 seconds. The next step must be entered while the LED is on.
STEP3 Press the [CH5] or [CH6] button one at a time or keep it pressed. The remote will emit a series of Power ON/OFF code signals. Release the [CH5] or [CH6] button as soon as the equipment turns off.
*Note : You can verify that you selected the correct code by pressing the [MUTE] button. The equipment should turn On or Off.
STEP4 Press the same [DEVICE] button to store the code. The Device LED will blink twice to confirm that the code has been stored.
E.To find the Three-Digit Code that Was Programmed using the Auto Search
Method
STEP1 Press the appropriate [DEVICE] button and the [OK/SEL] button simultaneously for three seconds. The device LED will turn on for 20 seconds. The next step must be performed while the LED is on.
5
STEP2 Press the [INFO] button. The device LED will blink a number of times indicating the number of each digit for the code. Each digit is separated by a one second interval of the LED being off.
Example : One blink, then three blinks, then eight blinks indicates the code number 138.
*Note : Ten blinks indicates the number 0.
F. Programming a Second TV to the DVD Button
STEP1 Press the [DVD] button and the [OK/SEL] button simultaneously for 3 seconds. The DVD LED will turn on for 20 seconds. The next step must be performed while the LED is on.
STEP2 Press the [TV] button.
STEP3 Point the remote control toward the TV and enter the three-digit code for your TV from the TV codes table.
STEP4 Store the three-digit code by pressing the [DVD] button. The device LED will blink twice to confirm that the code has been stored.
G. Programming for Advanced Functions.
In the CABLE device mode, the A,B,C,D and blank macro buttons can be programmed to act as a 'Macro' or Favorite Channel button. This allows you to program up to five 2-digit channels, four 3-digit channels or three 4-digit channels that can be accessed with ONE button press.
*Note : The A,B,C and D buttons are not programmable if you have a Digital Cable Box made by Pace, Pioneer or Scientific-Atlanta.
STEP1 Press the [CBL] button to select the CBL mode.
STEP2 Press the [MACRO] button and [OK/SEL] button simultaneously for 3 seconds. The [CBL] button will turn on for 20 seconds.
STEP3 Enter the the 2, 3 or 4-digit code for the channel you want programmed first (for example, 007) using the Number Pad, then press the [STOP] button. Then enter the code for the next channel (for example,
6
Loading...