Uniden UBC760XLT User Manual

urMen

BANK

LI L2 L3

U0C76OXLT BOOM HI

^ojtca^

I214S

1-20

2t-F0

41-60

vOL-5)-3qi.

□

□ □

©

@

( D ©

( r» i“i »_' C

~i C

I C' '_'

>

'.L' C _i

L4

L5

DLT .

661-80-808l-ai(00-(00

PRI L/0 OLY LMT MLD SCN SRC

□

□ □

©

®

©

0

LMT

SRC

L/0

® ® © ©

OFF

SCAN

MAN

PRI

HOLD

□

□ □

CLEAR

Bearcat

UBC 760XLT

100 Channel

Mobile/Base Scanner

о

Welcome to the world of computerized radio scanning. The Uniden Bearcat® 760 XLT is the resuit ofyears of research and development, and incorporates many un­ ique, state-of-the-art design concepts. Microelectronics allows so many sophisti­ cated features to be included in such a small, stylish unit The Uniden Bearcat® 760XLT uses the most recent technological advances to satisfy the highest per­ formance standards that can be achieved in a hand held unit The custom inte­ grated circuits, microprocessor, liquid crystal display, and other components have been designed to give the Uniden Bearcab® 760XLT high quality performance while maintaining low battery drain.

Uniden, one of the world leaders in radio scanners, has designed and manufac­ tured this unit to give you years of trouble free use. We are sure you will be proud to own the Uniden Bearcat® 760XLT, and to insure thatyou get the most out of all the features, please read this operating guide completely before using your scan­ ner.

WARNING

UNIDEN DOES NOT REPRESENT THIS UNIT TO BE WATER-PROOFED. TO REDUCE THE RISK OF ELECTRICAL SHOCK, FIRE HAZARD, OR DAM­ AGE TO THE UNIT, DO NOT EXPOSE TO RAIN OR MOISTURE.

For future reference, write in the model number and serial number below. You' will find them on the back of the unit.

Model No, _____	Serial No.
Purchased from;	___ Date
Unpacking

Carefully remove the unit from the shipping carton and check the contents against the following list;

*Bearcat Scanner

*DC Power Cord

*AC Adapter

*Mobile Mounting Bracket

*Telescopic Antenna

*Operating Guide [read it and save)

If any of these items are missing or if there are signs of physical damage, DO NOT attempt to operate the unit. Notify your dealer immediately.

NO TE: Keep the shipping carton and packing materiais, as well as all the printed ma­ terial. This carton serves as an excellent method to transport your new scanner for service or any other reason. .

On/Off, Volume - Turns the unit on or off, and controls the audio output level.

Squelch - Eliminates the annoying "rushing" sound that is present be­ tween transmissions when no sig­ nal is being received Proper adjust­ ment of this control keeps the re­ ceiver quiet and allows scanning until a signal is received

3.Sc<m - Press to start scanning all fre­ quencies programmed into memory that are not locked out.

4.Manual - Press to stop scanning.

Press again to manually step to the hext channel. Press the chahnel humberand then press the manual key to go directly to that channel.

Priority - The priority key samples channel 1 every two seconds re­ gardless of other operationai set­ tings.

Contraisi arid Functions

-®)

6.Hold - Press to stop and hold the search function on the current fre­ quency. Press again to manually step up to the preceding frequency

7.Loop Function - Program 5 fre­ quency bands U to L5,

To program these frequency bands it is only necessary to input an up­ per frequency and a lower frequen­ cy to specify a search range within one band.

8. Delay - The delay key provides a 2 second delay on any channel to re­ ceive a reply transmission on the same frequency before resuming search or scan. Delay is retained in memory.

9.Limit - Enter the low atad high li­ mits of the search range. Press to manually step the search frequency down.

10. Search - Press to search for new ac­ tive frequencies within preset ranges of any band

I I.Lockout/Clear -		Press	to lockout
the reception of frequencies on se­
lected	channels	during	scanning.
Lockout	is retained in		memory.

Press again to deselect lockout.

Pressing the lockout for 2.5 seconds will clearall the locked out frequen­ cies.

12 Numeric Keypad ("0-9" and ".") Used to program all frequencies in­ to memory and for direct channel access. During the scan mode these keys are utilized to select or deselect any of the 5 memory banks.

13. Enter - The "E" key is used to enter frequencies into the scanning memory.

	r-1	S-TT
¡4 Memory Lock - This unique		fea­

ture is used to lock the keypad to prevent accidental entries and is lo­ cated on the back panel

15 External Speaker - The external speaker Jack allows you to use an alternate speaker in case of a high noise environment. Use Uniden model ESP 25 external speaker for best results.

16. Tape Out - This jack allows you to con nect to any standard tape recor­ der in order to record transmissions