Uniden SC230 User Manual

0 (0)

SC230

OWNER’S

MANUAL

OWNER’S MANUAL

SC230

OWNER’S

MANUAL

OWNER’S MANUAL

Precautions

Before you use this scanner, please read and observe the

following.

IMPORTANT!

This scanning radio has been manufactured so that it will

not tune to the radio frequencies assigned by the FCC for

cellular telephone usage. The Electronic Communications

Privacy Act of 1986, as amended, makes it a federal

crime to intentionally intercept cellular or cordless

telephone transmissions or to market this radio when

altered to receive them. The installation, possession, or

use of this scanning radio in a motor vehicle may be

prohibited, regulated, or require a permit in certain states,

cities, and/or local jurisdictions. Your local law

enforcement officials should be able to provide you with

information regarding the laws in your community.

Changes or modifications to this product not expressly

approved by Uniden, or operation of this product in any

way other than as detailed by this Operating Guide, could

void your authority to operate this product.

EARPHONE WARNING!

Be sure to use only a monaural earphone with this

scanner. You can also use an optional 32 Ω stereo

headset. Use of an incorrect earphone or stereo headset

might be potentially hazardous to your hearing.

The output of the phone jack is monaural, but you will

hear it in both headphones of a stereo headset.

Set the volume to a comfortable audio level coming from

the speaker before plugging in the monaural earphone or

a stereo headset of the proper impedance (32 Ω).

Otherwise, you might experience some discomfort or

possible hearing damage if the volume suddenly

becomes too loud because of the volume control or

squelch control setting. This might be particularly true of

the type of earphone that is placed in the ear canal.

Precautions

WARNING!

Uniden does not represent this unit to be waterproof.

To reduce the risk of fire or electrical shock, do not

expose this unit to rain or moisture.

Motorola

, PL

, Private Line

, DPL

, and Digital

Private Line

are registered trademarks of Motorola, Inc.

NASCAR

is a registered trademark of the National

Association for Stock Car Auto Racing, Inc.

Uniden

and Bearcat

are registered trademarks of

Uniden America Corporation.

Close Call

™

is a proprietary trademarks of Uniden

America Corporation.

Other trademarks used throughout this manual are the

property of their respective holders.

Contents

The FCC Wants You to Know ............................................................ 7

Scanning Legally ............................................................................... 7

Introduction.......................................................................................... 9

Feature Highlights ............................................................................. 11

About This Manual........................................................................... 14

How the Scanner’s Controls Are Represented in This Manual ... 15

Entering Text ............................................................................... 15

Understanding Scanning .................................................................. 16

Understanding the Scanner’s Memory ............................................ 16

What is Scanning?........................................................................... 16

What is Searching? ......................................................................... 16

What is CTCSS/DCS?..................................................................... 17

Using the Scanner at the Racetrack................................................ 19

Conventional Scanning.................................................................... 19

Where To Get More Information...................................................... 20

Included With Your Scanner............................................................. 22

Setting Up Your Scanner .................................................................. 23

Using Internal Batteries ................................................................... 23

Using Rechargeable Batteries......................................................... 25

Using AC Power .............................................................................. 26

Connecting the Antenna .................................................................. 26

Connecting an Earphone/Headphone ..............................................27

Connecting an Extension Speaker ...................................................27

Attaching the Belt Clip ......................................................................27

Attaching the Wrist Strap..................................................................28

Installing the Demo Software............................................................28

A Look At The Keypad......................................................................29

A Look At The Display ......................................................................32

Using Menu ......................................................................................33

Using Func .......................................................................................33

Using the Scroll Control....................................................................33

Basic Operation ................................................................................. 34

Turning On the Scanner and Setting the Squelch ........................... 34

Scanning Systems........................................................................... 34

Scanning Preprogrammed Races ................................................... 35

Before You Get To The Track ..................................................... 35

When You Get To The Track....................................................... 35

Selecting Systems to Scan...............................................................36

Selecting System Channel Groups...................................................37

Locking/Unlocking Systems..............................................................37

Locking/Unlocking Channels ............................................................37

Temporarily Holding On a System................................................... 38

Holding On a Channel ..................................................................... 38

Quick-Storing Channels................................................................... 38

Quickly Recalling Channels............................................................. 39

Other Settings.................................................................................... 40

Displaying System Information ........................................................ 40

Viewing Memory Used ................................................................ 40

Viewing the Firmware Version .................................................... 40

Contents

Adjusting the Key Beep .................................................................. 40

Locking/Unlocking the Keypad ....................................................... 40

Turning Power Save On or Off ........................................................ 40

Priority Scan ................................................................................... 40

Using the Backlight ......................................................................... 41

Initializing the Scanner’s Memory ................................................... 41

Using the PC Control and Cloning Options ..................................... 42

Connecting Your Scanner to a Personal Computer .................... 42

Cloning the Scanner ................................................................... 43

Using the Menu ................................................................................. 44

Programming Radio Systems .......................................................... 46

Quickly Programming Racing Systems ........................................... 47

Manually Programming Racing Systems ........................................ 49

Editing the Car ............................................................................ 49

Entering/Editing a Car Number ................................................... 50

Editing a Driver ...........................................................................50

Setting a Car’s Quick Key ........................................................... 51

Editing a Car’s Channel .............................................................. 51

Deleting a Car ............................................................................. 51

Setting Lockout On A Car ........................................................... 52

Programming Conventional Systems.............................................. 52

Entering/Editing Conventional Channel Groups ......................... 53

Entering/Editing Conventional Channels .................................... 53

Programming/Editing Optional Settings......................................... 55

System-Level Settings ....................................................................55

Editing the System Name ...........................................................55

Editing the System Quick Key (Conventional Systems Only) ..... 55

Setting System Lockout .............................................................. 56

Setting the System Hold Time ....................................................56

Setting the Channel Delay Time ................................................. 57

Setting Data Skip ........................................................................ 57

Deleting Systems ........................................................................ 58

Copying Systems........................................................................ 58

Group-Level Settings ...................................................................... 58

Entering/Editing the Group Name ............................................... 58

Setting the Group Quick Key ......................................................59

Setting Group Lockout ................................................................ 60

Deleting Groups .......................................................................... 60

Channel-Level Settings................................................................... 60

Editing the Channel Name (Conventional Systems Only) .......... 60

Setting Channel Priority .............................................................. 61

Setting Channel Alert .................................................................. 62

Setting CTCSS/DCS ................................................................... 62

Setting Channel Modulation ........................................................ 63

Setting Channel Attenuation ....................................................... 64

Setting the Frequency Step ........................................................ 64

Setting Channel Lockout ............................................................. 65

Deleting Channels ...................................................................... 65

Copying/Pasting Channels ......................................................... 66

Contents

Searching and Storing ......................................................................67

Service Search ................................................................................67

Quick Search ................................................................................... 68

CTCSS/DCS Search .......................................................................68

Custom Search ................................................................................68

Editing a Custom Search Range ................................................ 69

Auto Search and Store ............................................................... 70

Selecting a System ......................................................................70

Storing a System .........................................................................71

Using the Close Call Feature ............................................................72

Setting Close Call Options ...............................................................73

Close Call Hits .................................................................................74

Search and Close Call Options ........................................................75

Managing Locked-Out Frequencies ................................................75

Unlocking All Frequencies ........................................................... 75

Reviewing Locked Out Frequencies ............................................75

Searching for Subaudible Tones .....................................................75

Screening Out Paging Systems .......................................................76

Finding Repeater Output Frequencies ........................................... 76

Setting the Maximum Auto Store Value .......................................... 77

Setting the Modulation Type ........................................................... 77

Setting Attenuation ......................................................................... 78

Setting Data Skip ............................................................................ 78

Setting the Delay Time .................................................................... 78

Setting the Search Frequency Step ................................................ 79

Using Weather Alert (SAME) ........................................................... 80

Searching For a Weather Broadcast .............................................. 80

Turning Weather Alert On/Off ......................................................... 80

Programming a SAME Group.......................................................... 81

Setting WX Alert Priority ................................................................. 82

Care and Maintenance ......................................................................83

Troubleshooting ................................................................................ 85

Specifications .................................................................................... 87

Optional Accessories ....................................................................... 89

Planning ............................................................................................ 90

Collecting Information ..................................................................... 90

Filling Out The Racing System Worksheet ..................................... 92

Race Name.................................................................................. 92

Car #/Driver-Frequency-Priority-CTCSS/DCS ............................ 92

Racing System Worksheet ............................................................. 93

Filling Out The Conventional System Worksheet ........................... 94

System Name and Quick Key ..................................................... 94

Group Name and Quick Key ....................................................... 94

Frequency-Alpha Tag-Priority-CTCSS/DCS ............................... 94

Conventional System Worksheet ................................................... 95

Preprogrammed Systems ................................................................ 96

One-Year Limited Warranty ............................................................. 97

The FCC Wants You to Know

This scanner has been tested and found to comply with

the limits for a scanning receiver, pursuant to Part 15 of

the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference in a

residential installation. This scanner generates, uses, and

can radiate radio frequency energy and, if not installed

and used in accordance with the instructions, may cause

harmful interference to radio communications.

However, there is no guarantee that interference will not

occur in a particular installation. If this scanner does

cause harmful interference to radio or television

reception, which can be determined by turning the

scanner on and off, you are encouraged to try to correct

the interference by one or more of the following

measures:

• Reorient or relocate the receiving antenna

• Increase the separation between the scanner and the

receiver

This device complies with Part 15 of the FCC Rules.

Operation is subject to the following two conditions:

1) This device may not cause harmful interference, and

2) this device must accept any interference received,

including interference that may cause undesired operation.

Scanning Legally

Your scanner covers frequencies used by many different

groups, including police and fire departments, ambulance

services, government agencies, private companies,

amateur radio services, military operations, pager services,

and wireline (telephone and telegraph) service providers.

It is legal to listen to almost every transmission your scanner

can receive. However, there are some transmissions that

you should never intentionally listen to. These include:

• Telephone conversations (cellular, cordless, or other

private means of telephone signal transmission)

• Pager transmissions

• Any scrambled or encrypted transmissions

The FCC Wants You to Know

According to the Electronic Communications Privacy Act

(ECPA), you are subject to fines and possible

imprisonment for intentionally listening to, using, or

divulging the contents of such a conversation unless you

have the consent of a party to the conversation (unless

such activity is otherwise illegal). This scanner has been

designed to prevent the reception of cellular telephone

transmissions and the decoding of scrambled

transmissions. This is done to comply with the legal

requirement that scanners be manufactured so they are

not easy to modify to pick up these transmissions. Do not

open your scanner’s case to make any modifications that

could allow it to pick up transmissions that are illegal to

monitor. Modifying or tampering with your scanner’s

internal components or using it in a way other than as

described in this manual could invalidate your warranty

and void your FCC authorization to operate it.

In some areas, mobile use of this scanner is unlawful or

requires a permit. Check the laws in your area. It is also

illegal in many areas (and a bad idea everywhere) to

interfere with the duties of public safety officials by

traveling to the scene of an incident without authorization.

Introduction

Your SC230 scanner is a state-of-the-art scanner radio

with automatic scanning capabilities. You can store fre-

quencies such as racing, police, fire/emergency, marine,

air, and other communications into the scanner. You can

carry it with you wherever you go, use it at home as a

base unit, or install it in your vehicle as a mobile unit.

You can use the scanner’s scroll control to quickly select

channels and frequencies, and you can automatically

program channels in a system using the AutoStore

feature.

Use your scanner to monitor:

• Automobile races

• Public safety systems

• Police and fire departments (including rescue and

paramedics)

• NOAA weather transmissions

• Business/Industrial radio

• Utilities

• Marine and amateur (ham radio) bands

• Air band

• Railroad

This table lists the frequency ranges, default frequency

step, default mode (AM or Narrowband FM), and type of

transmissions you can hear for each range.

Frequency

Range

(MHz)

Step

(kHz)

Mode Transmission

25.0-26.960 5 AM Petroleum/

Broadcast Band

26.965-

27.405

5 AM Citizens Band Class D

27.410-

27.995

5 AM Business Band

28.0-29.680 20 NFM 10 Meter

Amateur Band

Introduction

Frequency

Range

(MHz)

Step

(kHz)

Mode Transmission

29.7-49.990 10 NFM VHF Low Band

50.0-54.0 20 NFM 6 Meter

Amateur Band

108.0-

136.9750

25 AM Aircraft Band

137.0-

143.9875

12.5 NFM Military Band

144.0-

147.995

5NFM2 Meter

Amateur Band

148.0-

150.7875

12.5 NFM Military Band

150.800-

161.995

5 NFM VHF High Band

162.0-174.0 12.5 NFM Federal

Government

216.0-

224.9800

20 NFM 1.25 Meter Amateur

Band

400.0-

405.9875

12.5 NFM Miscellaneous

406.0-

419.9875

12.5 NFM Federal Land Mobile

420.0-

449.9875

12.5 NFM 70 cm

Amateur Band

450.0-

469.9875

12.5 NFM UHF

Standard Band

470.0-512.0 12.5 NFM UHF TV Band

806.0-

823.9875

12.5 NFM Public Service Band

849.0125-

868.9875

12.5 NFM Public Service Band

894.0125-

956.0000

12.5 NFM Public Service Band

1240.0000-

1300.0000

25 NFM 25 cm

Amateur Band

Feature Highlights

General

Close Call

RF Capture Technology - you can set the

scanner so it detects and provides information about

nearby radio transmissions. See “Using the Close Call

Feature” on Page 72 for more information.

Dynamically Allocated Channel Memory - your

scanner’s memory is organized so that it more closely

matches how radio systems actually work, making it easier

to program and use your scanner and determine how

much memory you have used and how much you have left.

Preprogrammed Races - your scanner is

preprogrammed with NASCAR Nextel, Busch, Craftsman,

Indy, ARCA, and Champ series races.

Quick Race Programming – lets you quickly and easily

enter information about a specific race.

Quick Keys – You can set the scanner so you can select

a race or systems and groups by pressing a single key.

This makes it easy to listen to or quickly lock out those

systems or groups you don’t want to scan.

Quick Car Select – You can set the scanner so you can

select and listen to a car by pressing a single key.

Pager Screen – You can set the scanner so it ignores hits

generated by common pager frequencies while using the

Close Call or search features.

Ten Service Searches - frequencies are preset in

separate public safety, news, amateur radio, marine,

railroad, air, CB radio, FRS/GMRS, racing, and special

searches, to make it easy to find specific transmissions.

Lockout – You can lock out any system, group,

frequency, or channel while scanning. If you lock out a

system or group, any channels belonging to that system

or group are also locked out.

You can lock out up to 200 frequencies. The scanner

skips locked-out frequencies while using the Close Call

feature or while searching.

Feature Highlights

CTCSS and DCS Squelch Modes – prevent

interference from stations not using the mode you select.

Dropout Delay – You can set whether the scanner

pauses at the end of a transmission to wait for a reply.

You can set the delay time for each system you scan, and

while searching and using the Close Call feature.

Attenuator – You can set the scanner’s attenuator to

reduce the input strength of strong signals by about 18 dB

received by the scanner.

Repeater Reverse – You can set the scanner so it

switches to the input frequency on a conventional

repeater system.

Channel Alert – You can set the scanner so it alerts you

when there is activity on any channel you specify.

Memory Check – Lets you see at a glance how much

total memory is left.

Frequency Step – Lets you select a frequency step

(5, 6.25, 7.5, 10, 12.5,15, 20, 25, 50 or 100 kHz) for

manual mode and chain search mode. The scanner’s

auto step feature lets you set the scanner so it automati-

cally chooses the correct step.

Quick Recall – Lets you quickly select a specific channel

by choosing the system, group, and channel.

Scan/Search Delay – You can set the scanner so it

remains on a frequency up to 5 seconds after the last

transmission to wait for a possible reply.

Text Tagging – You can name each race system, con-

ventional system, group, channel, custom search range,

and SAME group, using up to 16 characters per name.

Unique Data Skip – Allows your scanner to skip

unwanted data transmissions and reduces birdies.

Duplicate Frequency Alert – Alerts you if you try to enter

a duplicate name or frequency already stored in the

scanner.

Feature Highlights

Memory Backup – If power is lost or disconnected, the

scanner retains the frequencies you programmed in its

memory.

22 Bands – Includes 22 bands, with Aircraft and 800 MHz.

Note: The scanner’s frequency coverage is not continuous

and does not include the cellular telephone band.

Weather

Weather Search – Lets your scanner receive your local

NOAA weather transmission.

SAME Weather Alert – Lets your scanner alert you when

a SAME weather alert is transmitted on a NOAA weather

channel. The scanner also displays the transmitted alert

type. This helps you quickly find out about severe

weather in your area and lets you avoid false alarms.

Service Search – Lets you quickly select and search the

scanner’s preprogrammed frequencies.

Custom Search – Lets you program up to 10 custom

search ranges. You can search any of these ranges

simultaneously.

CTCSS/DCS Search – Lets the scanner search for CTCSS

or DCS tones. You can identify up to 50 CTCSS tones

and 104 DCS tones.

Quick Search – Lets you search from the currently-tuned

frequency if you are searching a conventional system.

Auto Store

Frequency AutoStore – Automatically stores all active

frequencies within a system you select.

Priority

Priority Scan – Priority channels let you keep track of

activity on your most important channel(s) while

monitoring other channels for transmissions.

Priority Plus – You can set the scanner so it scans only

the priority channels

Feature Highlights

Backlight and Power

LCD Back Light – Makes the display easy to see in dim

light. You can adjust the back light so it turns on when you

press a key, when squelch breaks during a transmission,

or manually.

Low Battery Alert – The scanner alerts you if the

batteries need to be recharged or replaced.

Battery Save – You can set the scanner so it reduces the

amount of power it needs if there are no transmissions.

Key Controls

Key Lock – You can deactivate the scanner’s keys to help

prevent accidentally changing the scanner’s programming.

Key Beep – You can control whether the scanner beeps

when you press a key.

PC Control and Cloning

PC Control – You can transfer programming data to and

from your scanner and your personal computer, and

control the scanner using a computer. This helps you find

frequencies listed on the Internet and load them into the

scanner.

Clone Mode – You can clone all programmed data,

including the contents of the scanner’s memory, menu

settings, and other parameters from one SC230

scanner to another SC230 scanner.

On-Air Cloning – You can clone all programmed data

over the air from one SC230 scanner to another SC230

scanner using a personal computer and a radio transmitter.

About This Manual

The screen displays used in this manual are

representations of what might appear when you use your

scanner. Since what you see depends on the frequencies

for your area and the settings you select, you might notice

some differences between what is in this manual and

what appears on your scanner.

Feature Highlights

How the Scanner’s Controls Are

Represented in This Manual

To help navigate the scanner’s menus, the steps shown in

this manual show the displays you see and the keys you

press or control you operate to get a desired result.

This example shows you how to use the scanner’s menu

to edit an existing system name. It shows you the key to

press ( ) to select a menu option and the option you

see (Program System) when you press . It also

instructs you to turn the scroll control (shown as

) to

view a series of choices then select one choice (Edit Name).

 Program System  E  

Select the system  E 



Edit Name  E

To get the most from this manual, review the contents to

become familiar with the basic functions available.

If you are new to scanning, be sure to read “Understand-

ing Scanning” on Page 16 for a quick background on the

technology. The first thing you’ll need to do is install bat-

teries in the scanner. Then you need to connect the

included antenna to the scanner. See “Setting Up Your

Scanner” on Page 23 if you need any help doing this.

Entering Text

To enter a letter, turn the scroll control until the

character you want appears, To enter a number, press a

number key. To enter a decimal point, press .

To move the cursor to the left, hold then press /4

or rotate the scroll control to the left. To move the cursor to

the right, hold then press 6/ or rotate the scroll

control to the right.

To clear a character, press No twice. To clear all

characters, press No 3 times. To accept an entry, press E

or press down on the scroll control.

Func

Understanding Scanning

This section provides you with background on how

scanning works. You don’t really need to know all of this

to use your scanner, but some background knowledge

will help you get the most from your SC230.

Understanding the Scanner’s Memory

Your scanner’s memory is organized in an architecture

called Dynamic Allocated Channel memory. This type of

memory is organized differently and more efficiently than

the bank/channel architecture used by traditional scanners.

Dynamic Allocated design matches how radio systems

actually work much more closely, making it easier to

program and use your scanner and determine how much

memory you have used and how much you have left.

Instead of being organized into separate banks and

channels, your scanner’s memory is contained in a pool.

You simply use as much memory as you need in the pool to

store as many frequencies and alpha tags as you need.

No memory space is wasted, and you can tell at a glance

how much memory you have used and how much

remains.

What is Scanning?

Unlike standard AM or FM radio stations, most two-way

communications do not transmit continuously. Your

SC230 scans programmed channels until it finds an

active frequency, then stops on that frequency and

remains on that channel as long as the transmission

continues. When the transmission ends, the scanning

cycle resumes until the scanner receives another

transmission.

What is Searching?

The SC230 can search each of its 22 bands and up to 10

banks together to find active frequencies. This is

different from scanning because you are searching for

frequencies that have not been programmed into the

scanner. When you select frequency bands to search, the

scanner searches for any active frequency within the

Understanding Scanning

lower and upper limits you specify. When the scanner

finds an active frequency, it stops on that frequency as

long as the transmission lasts. If you think the frequency

is interesting, you can program it into the scanner’s

memory. If not, you can continue to search.

What is CTCSS/DCS?

Your scanner can monitor systems using a Continuous

Tone Coded Squelch System (CTCSS) and Digital Coded

Squelch (DCS) system, which allow squelch to open only

when the tone you have programmed with a specific

frequency is received along with a transmission.

CTCSS and DCS are subaudible tone signaling systems

sometimes referred to as PL or DPL (Motorola’s

trademarked terms for Private Line and Digital Private

Line respectively). CTCSS and DCS are used only for FM

signals and are usually associated with both amateur and

commercial two-way frequencies. These systems make

use of a special subaudible tone that accompanies a

transmitted signal.

CTCSS and DCS are used for many purposes. In many

cases, CTCSS and DCS are used to restrict access to a

commercial repeater, so that only those units, which

transmit the correct tone along with their signal can “talk”

to the repeater.

CTCSS and DCS are also used in areas that receive

interference where there are several stations with output

frequencies close to each other. When this occurs, you

might hear multiple communications on the same

frequency. The stations might even interfere with each

other to the point where it is impossible to clearly receive

any of the stations. A scanner equipped with CTCSS and

DCS (like your scanner) can code each received

frequency with a specific CTCSS or DCS frequency.

Then, when you receive multiple signals, you only hear

the transmission with the CTCSS or DCS tone you

programmed. If you do not receive the correct tone with a

signal, the scanner’s squelch remains closed and you

hear nothing.

Understanding Scanning

You can search for the following CTCSS frequencies and

DCS codes.

CTCSS Frequencies (Hz)

DCS Codes (Octal)

67.0 69.3 71.9 74.4 77.0 79.7

82.5 85.4 88.5 91.5 94.8 97.4

100.0 103.5 107.2 110.9 114.8 118.8

123.0 127.3 131.8 136.5 141.3 146.2

151.4 156.7 159.8 162.2 165.5 167.9

171.3 173.8 177.3 179.9 183.5 186.2

189.9 192.8 196.6 199.5 203.5 206.5

210.7 218.1 225.7 229.1 233.6 241.8

250.3 254.1

023 025 026 031 032 036 043 047

051 053 054 065 071 072 073 074

114 115 116 122 125 131 132 134

143 145 152 155 156 162 165 172

174 205 212 223 225 226 243 244

245 246 251 252 255 261 263 265

266 271 274 306 311 315 325 331

332 343 346 351 356 364 365 371

411 412 413 423 431 432 445 446

452 454 455 462 464 465 466 503

506 516 523 526 532 546 565 606

612 624 627 631 632 654 662 664

703 712 723 731 732 734 743 754

Understanding Scanning

Using the Scanner at the Racetrack

Keeping up with the action at the racetrack is easy and

fun. You can hear drivers communicating with their pit

crews, officials communicating with drivers and crews,

and track workers communicating with everybody.

Each user at the racetrack transmits and receives on one

or more frequencies.

The scanner organizes racetrack frequencies by the

name of the race you are scanning and by car number.

For example, you might hear drivers and their pit crews

on the car number frequencies and officials and the news

media on the race frequencies. When you are scanning,

the scanner stops very briefly on each channel to see if

there is activity. If there isn’t, the scanner quickly moves

to the next channel. If there is, then the scanner pauses

on the transmission until it is over.

You can activate one racing system and as many

conventional systems as you want at the same time.

Within a racing system, each driver can have multiple fre-

quencies stored, but only one of their frequencies is

unlocked at any one time. If you select a driver frequency,

their other frequencies are automatically locked.

Conventional Scanning

Conventional scanning is a relatively simple concept.

Each group of users in a conventional system is assigned

a single frequency (for simplex systems) or two

frequencies (for repeater systems). Any time one of them

transmits, their transmission always goes out on the

same frequency. Up until the late 1980s, this was the

primary way that radio systems operated.

Even today, there are many 2-way radio users who

operate using a conventional system:

• Aircraft

• Amateur radio

• FRS/GMRS users

• Broadcast AM/FM/TV stations

• Many business radio users

Understanding Scanning

When you want to store a conventional system, all you

need to know is the frequencies they operate on.

When you are scanning a conventional system, the

scanner stops very briefly on each channel to see if there

is activity. If there isn’t, the scanner quickly moves to the

next channel. If there is, then the scanner pauses on the

transmission until it is over.

Simplex Operation

Simplex systems use a single frequency for both transmit

and receive. Most radios using this type of operation are

limited to line-of-sight operation. This type of radio is

frequently used at construction job sites, and with

inexpensive consumer radios such as GMRS/FRS radios.

The range is typically 1-8 miles, depending upon the

terrain and many other factors.

Repeater Operation

Repeater systems use two frequencies: one transmits from

the radio to a central repeater; the other transmits from the

repeater to other radios in the system. With a repeater-

based system, the repeater is located on top of a tall

building or on a radio tower that provides great visibility to

the area of operation. When a user transmits (on an input

frequency), the signal is picked up by the repeater and

retransmitted (on an output frequency). The user’s radios

always listen for activity on the output frequency and

transmit on the input frequency. Since the repeater is

located very high, there is a very large line of sight.

Typical repeater systems provide coverage out to about a

25-mile radius from the repeater location.

Where To Get More Information

By itself, this manual really only provides part of what you

need to know to have fun scanning – how to program and

use the scanner. The included conventional frequency

guide will give you a good head start on the other part of

what you need to know – what frequencies have

interesting content.

Understanding Scanning

Information On The Internet

The Internet is a great source for current frequencies and

information about scanning. Many web sites have lists of

frequencies for your area. You can use a search engine to

find and use them.

Make a list of the agencies you want to listen to, then look

up the frequencies and systems used by those agencies.

Here are a few useful sites:

• http://www.scannermaster.com * - frequency

resources and home of Police Call.

You can also call them at 1 800 SCANNER (hours are

from 9:00 a.m. to 5:30 p.m. Eastern Time Monday

through Friday).

• http://www.radioreference.com

- the Internet's

premier source for user-supported radio system

information.

• http://www.bearcat1.com - frequency information

from National Communications.

• http://svartifoss2.fcc.gov/reports/index.cfm

conventional frequency information on file with the US

Government

• http://groups.yahoo.com/group/SC230

- a group

for people interested in discussing the SC230.

* - These web sites are not affiliated with Uniden Corporation.

To purchase another copy of the conventional frequency

guide, contact your local dealer or:

Uniden Parts Department

(800) 554-3988

(Hours are from 8:00 a.m. to 5:00 p.m.Central Time

Monday through Friday.)

For more information about Uniden and our other

products, visit http://www.uniden.com.

Included With Your Scanner

If any of these items are missing or damaged,

immediately contact your place of purchase or Uniden

Customer Service at: (800) 297-1023, 8:00 a.m. to 5:00

p.m., Central, Monday through Friday.

Setting Up Your Scanner

Owners

Scanner

AC Adapter

Frequency Guide

Belt Clip

Manual

Antennas

Wrist Strap

Batteries

Connection

Cable

SC230

OWNER’S

MANUAL

OWNER’S MANUAL

Included With Your Scanner

Setting Up Your Scanner

These guidelines will help you install and set up your new

scanner:

• If your scanner receives interference or electrical

noise, move the scanner or its antenna away from the

source.

• To improve the scanner’s reception, use an optional

external antenna designed for multi-band coverage.

(You can purchase this type of antenna at a local

electronics store). If the optional antenna has no

cable, use 50-70 Ω coaxial cable for lead-in.

A mating plug might be necessary for the optional

antennas.

• Use an optional mono earphone or mono headset

with proper impedance (32 Ω) for private listening.

Read the precautions on the inside front cover of this

Owners Manual.

• Do not use the scanner in high-moisture

environments such as the kitchen or bathroom.

• Avoid placing the scanner in direct sunlight or near

heating elements or vents.

Using Internal Batteries

You can power your scanner using two alkaline, or

rechargeable AA batteries.

Setting Up Your Scanner

Before installing batteries, set the switch in the battery

compartment to match the type of batteries you will use.

Select REG. ALK. BATT. for non-rechargeable battery

types and NI-MH. BATT. for rechargeable battery types.

See also “Using Rechargeable Batteries” on Page 25

when you use rechargeable batteries.

1. Remove the battery cover and set the battery switch.

2. Install 2 AA batteries, matching the polarity symbols

(+ -).

WARNING!

Set REG. ALK. BATT./NI-MH. BATT. to NI-MH. BATT.

for use only with rechargeable batteries.

Never attempt to recharge non-rechargeable batteries.

Non-rechargeable batteries can get hot and can even

burst if you try to recharge them.

Setting Up Your Scanner

3. Replace the cover.

When flashes and the scanner beeps every 15

seconds, replace both batteries.

Using Rechargeable Batteries

You can also use two rechargeable batteries to power

your scanner. Before you use rechargeable batteries, you

must charge them.

The scanner has a built-in circuit that lets you recharge

batteries while they are in the scanner. To charge the

batteries, set REG. ALK. BATT./NI-MH. BATT. inside the

battery compartment to NI-MH. BATT., install the

batteries in the scanner, and connect the supplied

AC adapter to the scanner's DC 6V jack (see “Using AC

Power” on Page 26).

WARNING!

Do not connect the AC adapter to the scanner if non-

rechargeable batteries (such as alkaline batteries) are

installed in the scanner and

REG. ALK. BATT./NI-MH. BATT. is set to

NI-MH. BATT. , or if you are unsure of the switch's

position. Non-rechargeable batteries can get hot and

can even burst if you try to recharge them.

Setting Up Your Scanner

Before you use rechargeable batteries for the first time,

charge them for 14 hours to bring them to a full charge.

Discharged batteries take about 14 hours to fully

recharge.

Using AC Power

You can power the scanner using the supplied 6V,

500 mA AC adapter.

To use the scanner on AC power, plug the AC adapter

into a standard AC outlet.

If rechargeable batteries are installed and REG. ALK.

BATT./NI-MH. BATT. is set to NI-MH. BATT., the adapter

powers the scanner and recharges the installed batteries

at the same time.

Connecting the Antenna

To attach the supplied stub antenna to the connector on

the top of your scanner, align the slots around the

antenna's connector with the tabs on the scanner's BNC

connector. Then slide the antenna's connector down over

the scanner's connector and rotate the antenna

connector's outer ring clockwise until it locks into place.

Connecting an Optional Antenna

The scanner's BNC connector makes it easy to connect a

variety of optional antennas, including an external mobile

antenna or outdoor base station antenna.

Note: Always use 50-ohm, RG-58, or RG-8, coaxial cable

to connect an outdoor antenna. If the antenna is over 50

feet from the scanner, use RG-8 low-loss dielectric

coaxial cable. You can get a BNC adapter at your local

electronics store.

Setting Up Your Scanner

Connecting an Earphone/Headphone

For private listening, you can plug a

/8-inch (3.5 mm)

mini-plug earphone or headphones (not supplied) into the

headphone jack on top of your scanner.

This automatically disconnects the internal speaker.

See “Earphone Warning” at the front of the manual for

important information about using an earphone/

headphone.

Connecting an Extension Speaker

In a noisy area, an optional amplified extension speaker,

positioned in the right place, might provide more

comfortable listening. Plug the speaker cable's

/8-inch

(3.5-mm) mini-plug into your scanner's jack.

WARNING!

If you connect an external speaker to the scanner's

headphone jack, never connect the audio output line

to a power supply and ground. This might damage the

scanner.

Attaching the Belt Clip

To make your scanner easier to carry when you are on

the go, use the supplied belt clip. Use a Phillips

screwdriver and the supplied screws to attach the clip to

the scanner.

Setting Up Your Scanner

Attaching the Wrist Strap

To keep your scanner safely close at hand, use the

supplied wrist strap. Push the small loop on one end of

the wrist strap through the lug on the right side of the

scanner, then thread the other end of the wrist strap back

through the small loop to secure it.

Installing the Demo Software

You can operate your scanner using a personal computer

and the free demo software available at

http://www.uniden.com.

Download the software, then double-click on the install

package to begin installation. The SC230 Install

program installs the software. You must install the

software to use the scanner with your computer.

After you install the SC230 Install program, start it by dou-

ble clicking on the desktop icon or by selecting it in the

Start Programs list.

You can upgrade the included software to a full version by

purchasing a registration key at http://www.uniden.com.

Setting Up Your Scanner

A Look At The Keypad

Your scanner's keys have various functions labeled on

the key tops and below the keys. To select the function

labeled on a key, simply press the key. To select the

function labeled below a key, hold down on the left

side of the scanner then press the key. appears on

the display.

If your scanner's keys seem confusing at first, the follow-

ing information should help you understand each key's

function.

Key Name Description

CAR/

CAR – Selects a car in scan mode.

+ – Locks and unlocks

the keypad.

Hold/

Hold – Holds the scan or the

frequency search.

+ – Quickly turns the

Close Call feature on or off (see

“Setting Close Call Options” on

Page 73).

Scan/Srch Scan – Scans the stored channels.

+ Srch – Starts quick search

or quickly accesses the

search menu.

Func

Setting Up Your Scanner

L/O L/O – Lets you lock out a selected

channel or skip a specified

frequency.

+ L/O – Press quickly to lock

and unlock a selected system in

Scan or Scan Hold mode and

review search lockout frequencies

in Search or Search Hold mode.

Press and hold for more than 2

seconds to unlock all groups and

channels in a system.

/ – Press and hold for more than

2 seconds to turn the scanner on

or off. Press quickly to cancel a

prompt.

+ – Turns the display

backlight on or off.

1-9, 0/Race 1-9 – Enters a frequency, enters

quick key numbers, selects a

custom search range in Custom

Search mode, and selects systems

by quick key in scan mode.

0/Race – Selects the race quick

key, enters a frequency, and

selects a custom search range in

Custom Search mode.

+ 1-9, 0/Race – Selects

groups by quick key in scan mode.

1/Pri 1 – Enters a 1.

+ Pri – Selects the priority

mode in scan hold mode.

Key Name Description

Func

+ 69 hidden pages