DOOR PANEL INSTALLATION GUIDE |
® |
|
|
|
|
Overlay Door Panel
Preparation and Installation
Instructions
The Built-In Undercounter Leader Since 1962 |
U-LINE.COM |
|
|
Overlay Door Panel
Door panel Preparation
A Full overlay door panel completely covers the door frame and handle to give you a built-in appearance. See your U-Line dealer for the optional Full Overlay Door Panel Kit.
Full Overlay Door Panel Kit Part Number
|
2175 |
Black |
|
|
U-OL2175B |
|
|
2175 |
White |
|
|
U-OL2175W |
|
|
2115 & 2160 |
Black |
|
|
U-OL2115B |
|
|
2115 & 2160 |
White |
|
|
U-OL2115W |
|
Included In Kit: |
|
|
|
|
||
• |
1x Replacement Handle |
• |
2x |
Hinge Plates |
||
• |
2x |
Pivot Plate |
|
• |
1x |
Door Closer |
• |
1x |
Overlay Cap |
|
• |
2x |
Pivot Posts |
• |
8x |
#6x2” Drywall Screw |
• |
8x |
8-32 x1/2” Screws |
|
• |
2x |
8-32 x 3/8” Screws |
|
|
|
IMPORTANT
•The door panel must not weigh more than 20lbs.
•It is important to ensure that all drilled holes are drilled to the correct depth in order to avoid splits in the wood when hardware is installed.
•Rear view of wood panel for right-hand hinge shown. Use mirror image for left hand hinges.
•Appliance will need up to 34 1/2” to the under side of the counter to leave room for leveling adjustments
1.Determine cabinet toe kick height, by measuring the difference between the surface the appliance will rest on and the bottom of the adjacent cabinetry. Adjust panel height according to the height of you cabinetry’s Toe Kick.
2.Cut the overlay to the dimensions in Table A & B.
3.Drill hole for upper door hinge (top of panel) using a
#16 drill bit (0.177” diameter) x 11/16” deep (See diagram below)
4.Drill hole for lower door hinge 5/16” diameter x 1/4” deep (See diagram below)
Table A (Width) |
|
Model |
Width |
2175 |
23 3/4” |
2115 & 2160 |
14 3/4” |
Table B (Height) |
|
|
|
|
Toe Kick |
Height |
|
Toe Kick |
Height |
|
||||
3 3/4” |
29 3/4” |
|
4 1/4” |
29 3/8” |
3 7/8” |
29 3/4” |
|
4 3/8” |
29 1/4” |
4“ |
29 5/8” |
|
4 1/2” |
29 1/4” |
4 1/8” |
29 1/2” |
|
|
|
|
|
|
|
|
Note: Table B dimensions will vary based on the level of the floor. If floor is uneven, cut panel to the next longer dimension and adjust level legs to achieve proper fit
BACK SURFACE MUST BE A FLUSH FLAT SURFACE
FOR PANEL DOORS USE A BACKER BOARD
|
|
.750 |
|
|
MIN |
23.750 |
|
Detail A |
*75 Series |
14.750 |
|
|
|
|
|
*BI2115 & 2160 Series |
SEE DETAIL |
|
|
|
|
|
A |
13/16
15/32 |
|
3/8 |
3/16 |
C |
C
Detail B
1/4
5/16
CHAMFER 1/32" X 45°
D
3/8 |
D
13/32
SEE DETAIL
B
U-Line Door Panel Installation Guide |
1 |