Turbosound TCX-15B, TCX-15, TCX-18B, TCX-10, TCX-12 User Manual

...
4 (1)
Turbosound TCX-15B, TCX-15, TCX-18B, TCX-10, TCX-12 User Manual

Q u ic k S t a r t G u id e

TCX series

Models covered by this Quick Start Guide

TCX-8, TCX-10, TCX-12, TCX-15, TCX-15B, TCX-18B

Thank you for choosing a TURBOSOUND loudspeaker product for your application. If you would like further information about this or any other TURBOSOUND product, please visit our website at www.turbosound.com. A detailed user guide on this product range is available from ftp://ftp.turbosound.com

Unpacking the loudspeaker

After unpacking the unit please check carefully for damage. If damage is found, please notify your supplier at once. You, the consignee, must instigate any claim. Please retain all packaging in case of future re-shipment.

System requirements

TCX series two-way loudspeakers operate as passive systems and require only one amplifier channel for correct operation; the internal passive crossover network built into each enclosure splits the frequency range appropriately between the LF driver and the HF driver. TCX loudspeakers are equipped with two Speakon NL4 connectors wired in parallel with a 4-way barrier strip connector, providing input and loop-through connections to additional TCX series loudspeakers.

To avoid wasting amplifier power you should use heavy-duty speaker cable with a minimum²), andwirepsize of 12 gauge (1.5mm referably²) for10 gauge (2.5mm longer runs. For extreme cable lengths be aware of cable impedance and resistive losses. Always observe the correct polarity as shown.

Amplifier considerations

TCX series loudspeaker enclosures should be driven by high quality power amplifiers designed for true professional use. Power amplifiers should be capable of delivering long term broadband power equal to the loudspeaker’s program power rating at its stated nominal impedance. The use of under-powered amplifiers must be avoided as heavily clipped signals can cause permanent loudspeaker damage.

Model

TCX-8

TCX-10

TCX-12

TCX-15

TCX-15B

TCX-18B

 

 

 

 

 

 

 

Impedance

8Ω

8Ω

 

 

 

 

 

 

 

Amplifier power

400w

500w

600w

800w

2000w

2000w

 

 

 

 

 

 

 

System Controllers

TCX systems can be used with Turbosound LMS-D24 or LMS-D26 controllers to provide improved performance as well as vital operating and system security features. If you do not have a controller, please contact your Turbosound dealer for further details. Turbosound LMS-D2X controllers provide preset slots into which you can load TCX loudspeaker model parameters, available as a free download. To use your TCX loudspeaker with a Turbosound controller:

1.Download and install the presets for TCX loudspeakers from ftp://ftp.turbosound.com/tech_data

2.Power up the controller(s) and associated power amplifiers.

3.Press RECALL to select the appropriate program from the preset menu using the ÔA’ ROTARY ENCODER.

4.Press RECALL again to accept the preset. The controller will un-mute and is then ready for use.

TCX Series Quick Start Guide v1.1 - Page - 1

Quick Start Guide

TCX series

Networking capability with LMS series controllers

LMS-D2X controllers are designed to offer control and monitoring of system parameters over a BvNet network in real time using a PC and TurboDriveª software. The controllers are equipped with network cards to allow the building of comprehensive networked loudspeaker systems.

Download the TurboDrive™ software from the supplied CD or from ftp://ftp.turbosound.com/tech_data/software/ and follow the installation instructions.

Install the drivers. If connecting via RS232 there is no need to install drivers. If connecting via USB install the USB drivers which can be found on the CD that came with your Linea Research USB interface.

Networking multiple devices to a PC: BvNet is the method of connecting multiple devices and this is done with the Linea Research USB & RS232 Interface (available from Turbosound). The interface enables devices to be connected to a PC either using RS232 or using USB. EIA485 is the network protocol among the networked devices and is carried over CAT5-type cables. Minimum system requirements are: PC with Pentium processor, Windows NT, 2000, XP, or Vista, CD ROM drive or internet access, RS232 or USB port.

RS232: Connect your computer to the BvNet interface using a standard 9-pin serial cable. External power is required for RS232 operation and this should be provided by the Linea Research Accessory Power Supply.

USB: Connect your computer to the BvNet interface using a USB Type A to USB Type B cable. External power is not required when using USB.

Connect networked devices via RJ45 CAT5 cables.

Launch the TurboDriveª software.

Application Authorisation: TurboDriveª prompts for an Authorisation Code on the first launch which is PJLUWZ.

Select the COM port from Network > Com Port.

Click the Online toolbar button.

Click on one of the devices that appear in the tree view to Launch the panel.

When the progress bar indicates ready, adjust the controls as required.

Please refer to the TurboDriveª User Guide for further information on networking.

Mounting and fixing

TCX series cabinets are designed with multiple internal rigging points to suit many possible mounting methods in permanent installations. The table below summarises the mounting accessories required for each model in permanent installations

Model

Wall mount

Ceiling mount

OmniMountª

Speaker stand

Eyebolts

 

 

 

 

 

 

TCX-8

WB-20

CB-55

120 series

PA-100

EB-8

 

 

 

 

 

 

TCX-10

WB-55

CB-55

120 series

PA-90

EB-10/18

 

 

 

 

 

 

TCX-12

WB-55

CB-55

120 series

PA-90

EB-10/18

 

 

 

 

 

 

TCX-15

WB-55

CB-55

120 series

PA-90

EB-10/18

 

 

 

 

 

 

TCX-15B

N/A

N/A

N/A

PA-90/100

EB-10/18

 

 

 

 

 

 

TCX-18B

N/A

N/A

N/A

PA-90/100

EB-10/18

 

 

 

 

 

 

Use with speaker poles and speaker stands

Use speaker poles such as the PA-90 or PA-100 on top of a bass cabinet to raise the mid/high cabinets to above head height for better audience coverage.

For portable use remove the plastic bung covering the pole mount socket. Fit the speaker pole into the pole mount socket on the TCX bass cabinet and mount the TCX two-way cabinet to the top of the pole. TCX cabinets are compatible with standard 35mm speaker stands to raise mid/high cabinets to above head height for better audience coverage. Mount the cabinet on to the top of the speaker stand and tighten all adjusting screws. Always use caution when lifting the loudspeaker.

TCX Quick Start Guide v1.1 - Page - 2

Loading...
+ 4 hidden pages