1N4741A THRU 1M200Z
GLASS PASSIVATED JUNCTION SILICON ZENER DIODE
VOLTAGE - 11 TO 200 Volts Power - 1.0 Watt
DO-41
FEATURES
•Low profile package
•Built-in strain relief
•Glass passivated junction
•Low inductance
•Typical IR less than 5.0 A above 11V
•High temperature soldering :
260 /10 seconds at terminals
• Plastic package has Underwriters Laboratory Flammability Classification 94V-O
MECHANICAL DATA
Case: Molded plastic, DO-41
Epoxy: UL 94V-O rate flame retardant
Lead: Axial leads, solderable per MIL-STD-202, method 208 guaranteed
Polarity: Color band denotes cathode end
Mounting position: Any
Weight: 0.012 ounce, 0.3 gram
MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS
Ratings at 25 ambient temperature unless otherwise specified.
|
SYMBOL |
VALUE |
UNITS |
Peak Pulse Power Dissipation on TA=50 (Note A) |
PD |
1.0 |
Watts |
Derate above 50 |
|
6.67 |
mW/ |
Peak forward Surge Current 8.3ms single half sine-wave |
IFSM |
10 |
Amps |
superimposed on rated load(JEDEC Method) (Note B) |
|
|
|
Operating Junction and Storage Temperature Range |
TJ,TSTG |
-55 to +150 |
|
NOTES:
A.Mounted on 5.0mm2(.013mm thick) land areas.
B.Measured on 8.3ms, single half sine-wave or equivalent square wave, duty cycle = 4 pulses per minute maximum.
1N4741A THRU 1M200Z
*ELECTRICAL CHARACTERISTICS (TA=25 unless otherwise noted) VF=1.2V max, IF=200mA for all types.
Type No. |
Nominal Zener |
Test current |
Maximum Zener Impedance (Note 4.) |
Leakage Current |
Surge Current |
||||
(Note 1.) |
Voltage Vz @ IZT |
IZT |
@ TA=25 |
||||||
|
|
|
|
|
|||||
|
volts |
mA |
ZZT @ IZT |
ZZk @ IZK |
IZK |
IR |
VR |
Ir - mA |
|
|
(Notes2. And |
|
Ohms |
Ohms |
mA |
A Max |
Volts |
(Note 5.) |
|
|
3.) |
|
|
||||||
|
|
|
|
|
|
|
|
||
1N4741A |
11 |
23 |
8.0 |
700 |
0.25 |
5.0 |
8.4 |
414 |
|
1N4742A |
12 |
21 |
9.0 |
700 |
0.25 |
5.0 |
9.1 |
380 |
|
1N4743A |
13 |
19 |
10 |
700 |
0.25 |
5.0 |
9.9 |
344 |
|
1N4744A |
15 |
17 |
14 |
700 |
0.25 |
5.0 |
11.4 |
304 |
|
1N4745A |
16 |
15.5 |
16 |
700 |
0.25 |
5.0 |
12.2 |
285 |
|
1N4746A |
18 |
14 |
20 |
750 |
0.25 |
5.0 |
13.7 |
250 |
|
1N4747A |
20 |
12.5 |
22 |
750 |
0.25 |
5.0 |
15.2 |
225 |
|
1N4748A |
22 |
11.5 |
23 |
750 |
0.25 |
5.0 |
16.7 |
205 |
|
1N4749A |
24 |
10.5 |
25 |
750 |
0.25 |
5.0 |
18.2 |
190 |
|
1N4750A |
27 |
9.5 |
35 |
750 |
0.25 |
5.0 |
20.6 |
170 |
|
1N4751A |
30 |
8.5 |
40 |
1000 |
0.25 |
5.0 |
22.8 |
150 |
|
1N4752A |
33 |
7.5 |
45 |
1000 |
0.25 |
5.0 |
25.1 |
135 |
|
1N4753A |
36 |
7.0 |
50 |
1000 |
0.25 |
5.0 |
27.4 |
125 |
|
1N4754A |
39 |
6.5 |
60 |
1000 |
0.25 |
5.0 |
29.7 |
115 |
|
1N4755A |
43 |
6.0 |
70 |
1500 |
0.25 |
5.0 |
32.7 |
110 |
|
1N4756A |
47 |
5.5 |
80 |
1500 |
0.25 |
5.0 |
35.8 |
95 |
|
1N4757A |
51 |
5.0 |
95 |
1500 |
0.25 |
5.0 |
38.8 |
90 |
|
1N4758A |
56 |
4.5 |
110 |
2000 |
0.25 |
5.0 |
42.6 |
80 |
|
1N4759A |
62 |
4.0 |
125 |
2000 |
0.25 |
5.0 |
47.1 |
70 |
|
1N4760A |
68 |
3.7 |
150 |
2000 |
0.25 |
5.0 |
51.7 |
65 |
|
1N4761A |
75 |
3.3 |
175 |
2000 |
0.25 |
5.0 |
56.0 |
60 |
|
1N4762A |
82 |
3.0 |
200 |
3000 |
0.25 |
5.0 |
62.2 |
55 |
|
1N4763A |
91 |
2.8 |
250 |
3000 |
0.25 |
5.0 |
69.2 |
50 |
|
1N4764A |
100 |
2.5 |
350 |
3000 |
0.25 |
5.0 |
76.0 |
45 |
|
1M110Z |
110 |
2.3 |
450 |
4000 |
0.25 |
5.0 |
83.6 |
- |
|
1M120Z |
120 |
2 |
550 |
4500 |
0.25 |
5.0 |
91.2 |
- |
|
1M130Z |
130 |
1.9 |
700 |
5000 |
0.25 |
5.0 |
98.8 |
- |
|
1M150Z |
150 |
1.7 |
1000 |
6000 |
0.25 |
5.0 |
114.0 |
- |
|
1M160Z |
160 |
1.6 |
1100 |
6500 |
0.25 |
5.0 |
121.6 |
- |
|
1M180Z |
180 |
1.4 |
1200 |
7000 |
0.25 |
5.0 |
136.8 |
- |
|
1M200Z |
200 |
1.2 |
1500 |
8000 |
0.25 |
5.0 |
152.0 |
- |
NOTE:
1.Tolerance and Type Number Designation. The type numbers listed have a standard tolerance on the nominal zener voltage of ±5%.
2.Specials Available Include:
A.Nominal zener voltages between the voltages shown and tighter voltage tolerances.
B.Matched sets.
3.Zener Voltage (VZ) Measurement. Guarantees the zener voltage when measured at 90 seconds while maintaining the lead temperature (TL) at 30±1 , from the diode body.
4.Zener Impedance (ZZ) Derivation. The zener impedance is derived from the 60 cycle ac voltage, which results when an ac current having an rms value equal to 10% of the dc zener current (IZT or IZK) is superimposed on IZT or IZK.
5.Surge Current (Ir) Non-Repetitive. The rating listed in the electrical characteristics table is maximum peak, non-repetitive, reverse surge current of 1/2 square wave or equivalent sine wave pulse of 1/120 second duration superimposed on the test current, IZT, per JEDEC registration; however, actual device capability is as described in Figure 5.