Trotec TTR 55 E Operating Manual

Download

Page 1

TTR 55 E

OPERATING MANUAL

DEHUMIDIFIER

TRT-BA-TTR55E-TC-004-EN

Page 2

Notes regarding the operating manual................................. 1

Safety .....................................................................................1

You can download the current version of the operating manual and the EU declaration of conformity via the following link:

Information about the device................................................3

Transport and storage...........................................................4

Assembly and installation.....................................................5

Operation ...............................................................................6

Errors and faults....................................................................7

Maintenance ..........................................................................8

Technical annex...................................................................12

Disposal ...............................................................................13

Notes regarding the operating manual

Symbols

Warning of electrical voltage

This symbol indicates dangers to the life and health of persons due to electrical voltage.

Warning

This signal word indicates a hazard with an average risk level which, if not avoided, can result in serious injury or death.

Caution

This signal word indicates a hazard with a low risk level which, if not avoided, can result in minor or moderate injury.

Notice

This signal word indicates important information (e.g. material damage), but does not indicate hazards.

Info

Information marked with this symbol helps you to carry out your tasks quickly and safely.

Follow the manual

Information marked with this symbol indicates that the operating manual must be observed.

TTR 55 E

https://hub.trotec.com/?id=41255

Safety

Read this manual carefully before starting or using the device. Always store the manual in the immediate vicinity of the device or its site of use!

Warning Read all safety warnings and all instructions.

Failure to follow the warnings and instructions may result in electric shock, fire and/ or serious injury.

Save all warnings and instructions for future reference.

This appliance can be used by children aged from 8years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision.

• Do not use the device in potentially explosive rooms.

• Do not use the device in aggressive atmosphere.

• Set the device up in an upright and stable position.

• Let the device dry out after a wet clean. Do not operate it when wet.

• Do not use the device with wet or damp hands.

• Do not expose the device to directly squirting water.

• Never insert any objects or limbs into the device.

• Do not cover or transport the device during operation.

• Do not sit on the device.

• This appliance is not a toy! Keep away from children and animals. Do not leave the device unattended during operation.

• Check accessories and connection parts for possible damage prior to every use of the device. Do not use any defective devices or device parts.

1 EN

Operating manual – dehumidifier TTR 55 E

Page 3

• Ensure that all electric cables outside of the device are protected from damage (e.g. caused by animals). Never use the device if electric cables or the power connection are damaged!

• The electrical connection must correspond to the specifications in chapter Technical data.

• Insert the mains plug into a properly secured mains socket.

• Observe the device's power input, cable length and intended use when selecting extensions to the power cable. Completely unroll extension cables. Avoid electrical overload.

• Before carrying out maintenance, care or repair work on the device, remove the mains plug from the mains socket. Hold onto the mains plug while doing so.

• Switch the device off and disconnect the power cable from the mains socket when the device is not in use.

• Do not under any circumstances use the device if you detect damages on the mains plug or power cable. If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard. Defective power cables pose a serious health risk.

• When positioning the device, observe the minimum distances from walls and other objects as well as the storage and operating conditions specified in the Technical data chapter.

• Ensure that the air inlet and outlet are not obstructed.

• Ensure that the side of the device where the air inlet is found is kept free of dirt and loose objects.

• Only transport the device in an upright position with an emptied condensation tank or drain hose.

• Discharge the collected condensate before transport and storage. Do not drink it. Health hazard!

Intended use

Only use the device for drying and dehumidifying room air, while adhering to and following the technical data.

Intended use comprises:

• dehumidifying and drying:

– living rooms, bedrooms, bathrooms and basements – laundries, holiday homes, camper vans, boats

• maintaining the dryness of:

– storage spaces, archives, laboratories, garages – bathrooms, wash rooms, changing rooms etc.

Improper use

• Do not place the device on wet or flooded ground.

• Do not place any objects, e.g. clothing, on the device.

• Do not use the device outdoors.

• Any unauthorised modifications, alterations or structural changes to the device are forbidden.

• Any operation other than as described in this manual is prohibited. Non-observance renders all claims for liability and guarantee null and void.

Personnel qualifications

People who use this device must:

• be aware of the dangers that occur when working with electric devices in damp areas.

• have read and understood the operating manual, especially the Safety chapter.

Maintenance tasks which require the housing to be opened must only be carried out by specialist companies for cooling and air-conditioning or by Trotec.

EN 2

Operating manual – dehumidifier TTR 55 E

Page 4

Residual risks

Warning of electrical voltage

Work on the electrical components must only be carried out by an authorised specialist company!

Warning of electrical voltage

Before any work on the device, remove the mains plug from the mains socket! Hold onto the mains plug while pulling the power cable out of the mains socket.

Warning

Dangers can occur at the device when it is used by untrained people in an unprofessional or improper way! Observe the personnel qualifications!

Warning

The device is not a toy and does not belong in the hands of children.

Warning

Risk of suffocation! Do not leave the packaging lying around. Children may use it as a dangerous toy.

Notice

Do not operate the device without an inserted air filter! Without the air filter, the inside of the device will be heavily contaminated. This could reduce the performance and result in damage to the device.

Behaviour in the event of an emergency

1. Switch the device off.

2. In an emergency, disconnect the device from the mains feed-in: Hold onto the mains plug while pulling the power cable out of the mains socket.

3. Do not reconnect a defective device to the mains.

Information about the device

Description of the device

The device operates on the desiccant principle and comes equipped with an ioniser, a fan low in noise and maintenance, and a power cable with plug.

The fully automatic control and the condensation tank(2) with integrated overflow protection ensure fault-free operation.

The fan sucks in damp room air via the air inlet(3) with air filter(1), the condenser and the desiccant wheel located behind it.

Within the internal regeneration circuit the air is led via a heating element, it dries the desiccant wheel and leads the moist, warm air through the condenser. At the cooler condenser, heat is withdrawn from the room air and cooled below dew point. The water vapour contained in the room air precipitates in form of condensate.

Depending on the room air temperature and the relative humidity, the condensed water either drops continuously through the integrated drain nozzle into the condensation tank(2) below. The drier air which is prepared in this way mixes with the air in the room. Due to the continuous circulation of the room air through the device, the relative humidity inside the installation space is gradually reduced to the fixed humidity value (45 % RH).

A float is attached inside the condensation tank(2), which in case of a filled condensation tank interrupts the dehumidification via a microswitch. When switching off, the device emits an acoustic signal (3x) and the condensation tank indicator light on the control panel(6) is illuminated (see chapter Operating elements). The indicator light only goes out again once the emptied condensation tank(2) is reinserted. The device returns to the previously selected operation mode.

Negatively charged ions, which charge the oxygen molecules of the ambient air and bind suspended matter and dust particles in the air, are produced by means of the ionisation function.

3 EN

Operating manual – dehumidifier TTR 55 E

Page 5

Device depiction

Transport and storage

Notice

If you store or transport the device improperly, the device may be damaged. Note the information regarding transport and storage of the device.

Transport

To make the device easier to transport, it is fitted with a carry handle.

Before transporting the device, observe the following:

• Switch the device off.

• Hold onto the mains plug while pulling the power cable out of the mains socket.

• Do not use the power cable to drag the device.

• Drain the remaining condensate from the device and the condensation drain hose (see chapter Maintenance).

After transporting the device, observe the following:

• Set up the device in an upright position after transport.

• Leave the device to rest for one hour before switching it back on. Otherwise the device could be damaged and no longer work properly. Any warranty claims will be voided in this case.

No. Designation

1 Air filter

2 Condensation tank

3 Air inlet

4 Air outlet

5 Air flap

6 Control panel

7 Handle

Storage

Before storing the device, proceed as follows:

• Drain the remaining condensate from the device and the condensation drain hose (see chapter Maintenance).

• Empty and clean the condensation tank prior to storage.

When the device is not being used, observe the following storage conditions:

• dry and protected from frost and heat

• in an upright position where it is protected from dust and direct sunlight

• with a cover to protect it from invasive dust if necessary

• Place no further devices or objects on top of the device to prevent it from being damaged.

EN 4

Operating manual – dehumidifier TTR 55 E

Page 6

Assembly and installation

Scope of delivery

• 1x Device

• 1x Air filter

• 1x Manual

Unpacking the device

1. Open the cardboard box and take the device out.

2. Completely remove the packaging.

3. Fully unwind the power cable. Make sure that the power cable is not damaged and that you do not damage it during unwinding.

Start-up

When positioning the device, observe the minimum distance from walls or other objects as described in the Technical data chapter.

• When positioning the device, particularly in wet areas, secure it locally with an RCD (residual current device) which complies with the respective regulations.

Notes regarding the dehumidification performance

The dehumidification performance depends on:

• the layout of the room

• the room temperature

• the relative humidity

The higher the room temperature and relative humidity, the greater the dehumidification performance.

For use in living rooms, a relative humidity of approx. 50 to 60% is sufficient. In storage facilities and archives, the humidity should not exceed approx. 50%.

Inserting the air filter

Notice

• Make sure that the air filter is installed before switching the device on.

• Before restarting the device, check the condition of the power cable. If there are doubts as to the sound condition, contact the customer service.

• Set the device up in an upright and stable position.

• Do not create tripping hazards when laying the power cable or other electric cables, especially when positioning the device in the middle of the room. Use cable bridges.

• Make sure that extension cables are completely unrolled.

• When positioning the device, keep a sufficient distance to heat sources.

Inserting the condensation tank

• Ensure that the float inside the condensation tank is inserted correctly.

• Ensure that the condensation tank is empty and inserted correctly.

Connecting the power cable

• Insert the mains plug into a properly secured mains socket.

• Make sure that no curtains or other objects interfere with the air flow.

5 EN

Operating manual – dehumidifier TTR 55 E

Page 7

Operation

FULL

POWER ION UPPER

BELOW

WIDE

AUTO

CONT

DRY

MUTE

POWER ION SWING TIMER SELECT

1516

• After being switched on, the device operates fully automatically until the float indicates that the condensation tank is full and the device switches itself off.

• Avoid open doors and windows.

Operating elements

Switching the device on

Once you have completely installed the device as described in the Start-up chapter, you can switch it on.

1. Press the Power button(17).

2. Check whether the condensation tank indicator light(8) is out.

3. Select the desired operation mode by use of button13.

Info

If the target humidity value is not reached within 24hours, the device switches off automatically regardless of the operating mode. The device also switches off if the target value was reached for a short time but the heating could not cool down sufficiently. After reaching the target value, the heating requires a certain time (approx.6min) to cool down. If the target value is reached within 24hours and the heating always has sufficient time to cool down, the device will remain in operation even for weeks.

No. Operating element

8 FULL:

Condensation tank indicator light; is illuminated when the condensation tank is full. POWER: Is illuminated when the device is switched on.

9 ION:

Is illuminated when ionisation mode is activated.

10 WIDE:

Is illuminated when the air flap is fully pivoted from bottom to top. BELOW: Is illuminated when the air flap is only pivoted in the lower angle range. UPPER: Is illuminated when the air flap is only pivoted in the upper angle range.

11 One of the indicators is illuminated when the switch-off

timer is activated by means of the TIMER button (1 = one hour, 2 = two hours, 4 = four hours, 8 = eight hours).

12 The corresponding indicator light of the selected

operation mode is illuminated. AUTO: Normal operation mode CONT: Continuous operation DRY: Eco mode MUTE: Low-noise operation mode

13 Button to select the operation mode

14 Button to activate and set the switch-off timer

15 Button to adjust the position of the air flap

16 Button to activate the ionisation function

17 Power button; switches the device on or off.

EN 6

Operating manual – dehumidifier TTR 55 E

Normal operation mode (AUTO)

The device regulates the dehumidification performance according to the room air's humidity level and the fan stage:

• Above a humidity of 70 %, heater and fan work at the

highest level.

• With a humidity level between 50 % and 70 % the heater

works in low stage and the fan in medium stage.

• Below 50 % humidity, the heater is switched off and the

fan works at the lowest stage.

Start normal operation mode as follows:

1. Repeatedly press the button for the selection of the operation mode(13) until the indicator light AUTO(12) is illuminated.

Continuous operation mode (CONT)

In continuous operation mode, the device dehumidifies the air constantly, regardless of the humidity. This special function improves the clothes drying process by continuous operation of the dehumidifier at full capacity.

Start the continuous operation mode as follows:

1. Repeatedly press the button for the selection of the operation mode(13) until the indicator light CONT(12) is illuminated.

Eco mode (DRY)

In eco mode, the device works at the lowest heating level. The fan rotates at medium speed. Thus, the energy consumption is reduced.

Start eco mode as follows:

1. Repeatedly press the button for the selection of the operation mode(13) until the indicator light DRY(12) is illuminated.

Page 8

Low-noise operation mode (MUTE)

In low-noise operation mode, the device works at the lowest heating level. The fan rotates at minimum speed.

Start low-noise operation mode as follows:

1. Repeatedly press the button for the selection of the operation mode(13) until the indicator light MUTE(12) is illuminated.

Ionisation function (ION)

When activating the ionisation function, the ion generator produces negatively charged ions. These ions charge the oxygen molecules of the ambient air and bind suspended matter and dust particles in the air. This way the ambient air is cleaned, which improves human well-being.

Start the ionisation function as follows:

1. Press the button for the activation of the ion generator(16) until the indicator light ION(9) is illuminated.

Switch-off timer

Use the switch-off timer to automatically switch off the device after a specified time interval (1, 2, 4 or 8 hours).

Start the switch-off timer as follows:

1. Repeatedly press button14 until one of the indicator lights(11) is illuminated and thus indicates the set switchoff time value in hours.

2. Press button14 again to disable the switch-off timer.

Shutdown

Warning of electrical voltage

Do not touch the mains plug with wet or damp hands.

• Switch off the device.

• Wait for approx. 2 minutes.

– Due to the follow-up time of the internal components,

the device only switches off completely after approx. 2 minutes.

• Hold onto the mains plug while pulling the power cable out

of the mains socket.

• Empty the condensation tank, if need be.

• Clean the device according to the Maintenance chapter.

• Store the device according to the Storage chapter.

Errors and faults

The device has been checked for proper functioning several times during production. If malfunctions occur nonetheless, check the device according to the following list.

The device does not start:

• Check the power connection.

• Check the power cable and mains plug for damages.

• Check the on-site fusing.

• Check the condensation tank for correct seating.

• Check the room temperature. Observe the device's permissible operating range according to the technical data.

• Wait for 10minutes before restarting the device. If the device is not starting, have the electrics checked by a specialist company or by Trotec.

The device is running, but there is no formation of condensate:

• Check the float in the condensation tank for dirt. If necessary, clean the condensation tank. The float must be able to move freely.

• Check the room temperature. Observe the device's permissible operating range according to the technical data.

• Ensure that the relative room humidity complies with the technical data.

• Check the preselected desired humidity level. The humidity in the room must be above the selected range. If required, select another operation mode by use of button13.

• Check the air filter for dirt. If necessary, clean or replace the air filter.

• From the outside, check the condenser for dirt (see chapter Maintenance). If the condenser is dirty, have it cleaned by a specialist company or by Trotec.

The device is loud or vibrates:

• Check whether the device is set up in a stable and upright position.

Condensate is leaking:

• Check the device for leaks.

The device gets very warm, is loud or loses power:

• Check the air inlets and air filter for dirt. Remove external dirt.

• From the outside, check the device for dirt (see chapter Maintenance). If the inside of the device is dirty, have it cleaned by a specialist company for cooling and airconditioning or by Trotec.

Notice

Wait for at least 3 minutes after maintenance and repair work. Only then switch the device back on.

Your device still does not operate correctly after these checks?

Please contact the customer service. If necessary, bring the device to a specialist company for cooling and air-conditioning or to Trotec for repair.

Notice

For reasons of safety, the device switches off automatically after a period of 24hours.

7 EN

Operating manual – dehumidifier TTR 55 E

Page 9

Maintenance

Maintenance intervals

Maintenance and care interval before every

start-up

Empty condensation tank and drain hose

Check the air inlets and outlets for

X X

dirt and foreign objects and clean if necessary

Clean the exterior

Visually check the inside of the device for dirt

Check the air filter for dirt and

X X

foreign objects and clean or replace if necessary

Replace air filter

Check for damage

Check the attachment screws

Test run

as needed at least every

2 weeks

X X

at least every 4 weeks

at least every 6 months

at least annually

EN 8

Operating manual – dehumidifier TTR 55 E

Page 10

Maintenance and care log

Device type: .............................................

Device number: ....................................

Maintenance and care interval

Empty condensation tank and drain hose

Check the air inlets and outlets for dirt and foreign objects and clean if necessary

Clean the exterior

Visually check the inside of the device for dirt

Check the air filter for dirt and foreign objects and clean or replace if necessary

Replace air filter

Check for damage

Check the attachment screws

Test run

Remarks:

1. Date: ................................