Trotec TTK 54 E, TTK 96 E, TTK 127 E Operating Manual

Download

Page 1

TTK 54 E

OPERATING MANUAL

DEHUMIDIFIER

TRT-BA-TTK54E-TC2019-28-001-EN

Page 2

Notes regarding the operating manual................................. 2

Safety .....................................................................................2

You can download the current version of the operating manual and the EU declaration of conformity via the following link:

Information about the device................................................5

Transport and storage...........................................................6

Assembly and installation.....................................................6

Operation ...............................................................................7

Errors and faults..................................................................10

Maintenance ........................................................................12

Technical annex...................................................................15

Disposal ...............................................................................18

Notes regarding the operating manual

Symbols

Danger

This symbol indicates dangers to the life and health of persons due to extremely flammable gas.

Warning of electrical voltage

This symbol indicates dangers to the life and health of persons due to electrical voltage.

Warning

This signal word indicates a hazard with an average risk level which, if not avoided, can result in serious injury or death.

Caution

This signal word indicates a hazard with a low risk level which, if not avoided, can result in minor or moderate injury.

Note

This signal word indicates important information (e.g. material damage), but does not indicate hazards.

Info

Information marked with this symbol helps you to carry out your tasks quickly and safely.

Follow the manual

Information marked with this symbol indicates that the operating manual must be observed.

TTK 54 E

https://hub.trotec.com/?id=40260

Safety

Read this manual carefully before starting or using the device. Always store the manual in the immediate vicinity of the device or its site of use!

Warning Read all safety warnings and all instructions.

Failure to follow the warnings and instructions may result in electric shock, fire and/ or serious injury.

Save all warnings and instructions for future reference.

This appliance can be used by children aged from 8years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision.

• Do not use the device in potentially explosive rooms.

• Do not use the device in aggressive atmosphere.

• Set the device up in an upright and stable position.

• Let the device dry out after a wet clean. Do not operate it when wet.

• Do not use the device with wet or damp hands.

• Do not expose the device to directly squirting water.

• Never insert any objects or limbs into the device.

• Do not cover or transport the device during operation.

• Do not sit on the device.

• This appliance is not a toy! Keep away from children and animals. Do not leave the device unattended during operation.

• Check accessories and connection parts for possible damage prior to every use of the device. Do not use any defective devices or device parts.

2 EN

dehumidifier TTK 54 E

Page 3

• Ensure that all electric cables outside of the device are protected from damage (e.g. caused by animals). Never use the device if electric cables or the power connection are damaged!

• The electrical connection must correspond to the specifications in chapter Technical data.

• Insert the mains plug into a properly secured mains socket.

• Observe the device's power input, cable length and intended use when selecting extensions to the power cable. Completely unroll extension cables. Avoid electrical overload.

• Before carrying out maintenance, care or repair work on the device, remove the mains plug from the mains socket. Hold onto the mains plug while doing so.

• Switch the device off and disconnect the power cable from the mains socket when the device is not in use.

• Do not under any circumstances use the device if you detect damages on the mains plug or power cable. If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard. Defective power cables pose a serious health risk!

• When positioning the device, observe the minimum distances from walls and other objects as well as the storage and operating conditions specified in the Technical data chapter.

• Make sure that the air inlet and outlet are not obstructed.

• Make sure that the suction side is kept free of dirt and loose objects.

• Do not remove any safety signs, stickers or labels from the device. Keep all safety signs, stickers and labels in legible condition.

• Only transport the device in an upright position with an emptied condensation tank or drain hose.

• Discharge the collected condensate before transport and storage. Do not drink it. Health hazard!

Safety warnings for dehumidifiers filled with R290

• Only position the device in rooms where potentially leaking refrigerant cannot accumulate.

• Only position the device in rooms where there is no permanent source of ignition (e.g. open flames, an active gas appliance or an electric heater).

• Please note that the refrigerant is odourless.

• Only install the device in compliance with the national installation regulations.

• Observe the national gas regulations.

• Only install, operate and store the device TTK 54 E in a room measuring more than 4m2.

• Store the device in a way that no mechanical damage can occur.

• Please note that the connected ducts must not contain any sources of ignition.

• R290 is a refrigerant that complies with European environmental regulations. No part of the cooling circuit may be perforated.

• Do not drill through or burn.

• Do not use any means other than those recommended by the manufacturer for accelerating the defrosting process.

• Every person working with or at the refrigerant circuit must be able to provide a certificate of qualification issued by a body accredited by the industry, demonstrating their competence in the safe use of refrigerants based on a procedure well-known in the industry.

• Service work may only be carried out in accordance with the manufacturer's specifications. If maintenance and repair work require the support of additional persons, the person trained in handling flammable refrigerants shall continuously supervise the work carried out.

• Unventilated rooms, in which the device is installed, operated or stored, must be built in a way to ensure that potentially leaking refrigerant cannot accumulate. This serves to avoid fire or explosion hazards resulting from an ignition of the refrigerant by an electric furnace, cooking stove or another ignition source.

• The entire refrigerant circuit is a maintenance-free, hermetically sealed system and may only be maintained or repaired by specialist companies for cooling and airconditioning or by Trotec.

Intended use

Only use the device for drying and dehumidifying room air, while adhering to and following the technical data.

In addition, the device may also be used as a kind of clothes dryer to dry wet laundry.

Intended use comprises:

• dehumidifying and drying:

– living rooms, bedrooms, bathrooms and basements – laundries, holiday homes, camper vans, boats

• maintaining the dryness of:

– storage spaces, archives, laboratories, garages – bathrooms, wash rooms, changing rooms etc.

EN 3

dehumidifier TTK 54 E

Page 4

Improper use

The device is not intended for industrial use.

• Do not place the device on wet or flooded ground.

• Do not place any objects, e.g. clothing, on the device.

• Do not use the device outdoors.

• Any unauthorised modifications, alterations or structural changes to the device are forbidden.

• Any operation other than as described in this manual is prohibited. Non-observance renders all claims for liability and guarantee null and void.

Personnel qualifications

People who use this device must:

• be aware of the dangers that occur when working with electric devices in damp areas.

• have read and understood the operating manual, especially the Safety chapter.

Maintenance tasks which require the housing to be opened must only be carried out by specialist companies for cooling and air-conditioning or by Trotec.

Safety signs and labels on the device

Residual risks

Danger Natural refrigerant propane (R290)!

H220 – Extremely flammable gas. H280 – Contains gas under pressure; may explode if heated.

P210 – Keep away from heat, sparks, open flames and other ignition sources. No smoking. P377 – Leaking gas fire: Do not extinguish, unless leak can be stopped safely. P410+P403 – Protect from sunlight. Store in a wellventilated place.

Warning of electrical voltage

Work on the electrical components must only be carried out by an authorised specialist company!

Warning of electrical voltage

Before any work on the device, remove the mains plug from the mains socket! Hold onto the mains plug while pulling the power cable out of the mains socket.

Note

Do not remove any safety signs, stickers or labels from the device. Keep all safety signs, stickers and labels in legible condition.

The following safety signs and labels are attached to the device:

TTK54E

Follow the manual

This symbol indicates that the operating manual must be observed.

Follow the repair manual

Disposal, maintenance and repair work of the refrigerant circuit may only be carried out in accordance with the manufacturer's specifications and by persons having a certificate of qualification. A corresponding repair manual is available from the manufacturer upon request.

Warning

Dangers can occur at the device when it is used by untrained people in an unprofessional or improper way! Observe the personnel qualifications!

Warning

The device is not a toy and does not belong in the hands of children.

Warning

Risk of suffocation! Do not leave the packaging lying around. Children may use it as a dangerous toy.

Note

Do not operate the device without an inserted air filter! Without the air filter, the inside of the device will be heavily contaminated. This could reduce the performance and result in damage to the device.

Behaviour in the event of an emergency

1. Switch off the device.

2. In an emergency, disconnect the device from the mains feed-in: Hold onto the mains plug while pulling the power cable out of the mains socket.

3. Do not reconnect a defective device to the mains.

4 EN

dehumidifier TTK 54 E

Page 5

Information about the device

MODE ON/OFFTIMERTURBO

ION

O

Full

Dryer

SMDCont.

Description of the device

The device uses the principle of condensation to automatically dehumidify rooms.

The fan sucks damp room air through the air inlet, the air filter, the evaporator and to the condenser located behind it. The air is cooled at the cold evaporator until it is below the dew point. Water vapour contained in the room air precipitates on the evaporator fins as condensation or rime. The dehumidified, cooled air is slightly warmed at the condenser and blown out again. The drier air thus conditioned mixes with the air in the room. The humidity in the room where the device is positioned is reduced as air constantly circulates through the device.

Depending on the air temperature and the relative humidity, the condensed water either drops continuously or only during the defrost phase through the integrated drain nozzle into the condensation tank below. It is fitted with a float to measure the filling level.

The device has a control panel for operating and controlling the functions.

Once the maximum filling level of the condensation tank is reached or if the tank is not installed correctly, the condensation tank indicator light on the control panel will be illuminated and an error code will be displayed as well (see chapter Operating elements). The device switches off. The indications only disappear once the emptied condensation tank is reinserted.

Optionally, the condensed water can be drained by attaching a hose at the condensation connection.

The device can reduce the relative humidity of a room to approx. 35%.

In addition, the device may also be used as a kind of clothes dryer to dry wet laundry in living or working spaces.

Because of the heat radiation generated during operation, the room temperature may rise slightly.

Device depiction

No. Designation

1 Control panel

2 Transport handle

3 Wheels

4 Air inlet with air filter

5 Power cable holder

6 Condensation drain hose

7 Condensation drain hose connection

8 Condensation tank with filling level indicator

EN 5

dehumidifier TTK 54 E

9 Air outlet

Page 6

Transport and storage

Assembly and installation

Note

If you store or transport the device improperly, the device may be damaged. Note the information regarding transport and storage of the device.

Transport

To make the device easier to transport, it is fitted with a carry handle.

To make the device easier to transport, it is fitted with wheels.

Before transporting the device, observe the following:

• Switch off the device.

• Hold onto the mains plug while pulling the power cable out of the mains socket.

• Do not use the power cable to drag the device.

• Drain the remaining condensate from the device and the condensation drain hose (see chapter Maintenance).

• Only wheel the device on a level and smooth surface.

After transporting the device, observe the following:

• Set up the device in an upright position after transport.

• Leave the device to rest for 12to24hours, so the refrigerant can accumulate within the compressor. Wait 12to24hours before switching the device back on! Acting contrary might lead to compressor damage and a malfunctioning device. If so, any warranty claims will be voided.

Scope of delivery

• 1x Device

• 1x condensation drain hose, length: 0.6 m, diameter: 14 mm

• 1x air filter

• 1x Manual

Unpacking the device

1. Open the cardboard box and take the device out.

2. Completely remove the packaging.

3. Fully unwind the power cable. Make sure that the power cable is not damaged and that you do not damage it during unwinding.

Start-up

When positioning the device, observe the minimum distance from walls or other objects as described in the Technical data chapter.

Storage

Before storing the device, proceed as follows:

• Drain the remaining condensate from the device and the condensation drain hose (see chapter Maintenance).

• Empty and clean the condensation tank and the condensation drain hose prior to storage.

• Hold onto the mains plug while pulling the power cable out of the mains socket.

When the device is not being used, observe the following storage conditions:

• Only store the device in a room measuring more than 4m2.

• dry and protected from frost and heat

• in an upright position where it is protected from dust and direct sunlight

• with a cover to protect it from invasive dust, if necessary

• Place no further devices or objects on top of the device to prevent it from being damaged.

• Before restarting the device, check the condition of the power cable. If there are doubts as to the sound condition, contact the customer service.

• Only position the device in rooms where potentially leaking refrigerant cannot accumulate.

• Only position the device in rooms where there is no permanent source of ignition (e.g. open flames, an active gas appliance or an electric heater).

• Set the device up in an upright and stable position.

6 EN

dehumidifier TTK 54 E

Page 7

• Do not create tripping hazards when laying the power

10 11 12 13 14

1718

1920212223

cable or other electric cables, especially when positioning the device in the middle of the room. Use cable bridges.

• Make sure that extension cables are completely unrolled.

• When positioning the device, keep a sufficient distance to heat sources.

• Make sure that no curtains or other objects interfere with the air flow.

• When positioning the device, particularly in wet areas, secure it locally with an RCD (residual current device) which complies with the respective regulations.

Inserting the air filter

Note

• Make sure that the air filter is installed before switching the device on.

Operation

Notes:

• Avoid open doors and windows.

• After being switched on, the device operates fully automatically.

• The fan permanently runs in dehumidification mode until the set nominal value is reached. The fan keeps running for approx. 3minutes and then switches off.

Operating elements

Inserting the condensation tank

• Ensure that the float inside the condensation tank is inserted correctly.

• Ensure that the condensation tank is empty and inserted correctly.

Connecting the power cable

• Insert the mains plug into a properly secured mains socket.

No. Designation Meaning

10 TIMER LED Illuminated when the timer is

activated

11 Fan speed LEDs Fan speed indication:

Low Med(ium) High (low + med.)

12 Full LED Condensation tank full or not

inserted correctly

13 Dryer LED Laundry drying mode is enabled

14 Cont. LED Continuous operation is enabled

15 Comfort LED Comfort mode is enabled

16 Power LED Illuminated during operation

17 ON/OFF button Power button:

switching the device on and off

18 MODE button Selection button for operating

modes:

Dehumidification (not indicated) Dryer = laundry drying function Cont. = continuous operation Comfort = comfort mode

19 Increase value button Setting the relative room

humidity Setting the number of hours for the timer function

EN 7

dehumidifier TTK 54 E

Page 8

No. Designation Meaning

20 Segment display Indication of the current relative

room humidity level Indication of the relative room humidity level during set-up Indication of the number of hours during timer programming Display of error codes

21 Decrease value button Setting the relative room

humidity Setting the number of hours for the timer function

22 FAN button Setting high, medium or low fan

speed

23 TIMER button Switches the timer function on

or off.

Info

An acoustic signal is emitted each time a setting is activated.

Switching the device on

Once you have completely installed the device as described in the Start-up chapter, you can switch it on.

1. Press the ON/OFF button(17).

ð The device starts in dehumidification mode.

Setting the operating mode

• Dehumidification

• Continuous operation

• Comfort mode

• Laundry drying function

Dehumidification

The device keeps running until reaching the desired relative room humidity. Once the desired relative room humidity is exceeded, the compressor and ventilation switch back on.

In this operating mode, the desired relative room humidity can be set at any time in increments of 5% within a setting range of 35% to 85%.

1. Press the MODE button(18) until only the Power LED(16) is lit.

2. Press the Increase value(19) or Decrease value button(21) to select the relative room humidity.

ð The desired relative room humidity is indicated in the

segment display(20) for approx.5seconds. Then the current relative room humidity is displayed again.

Setting the desired relative room humidity

You can only change the relative room humidity in dehumidification mode.

1. Press the Increase value(19) or Decrease value button(21) to set the relative room humidity. Setting is possible within the range between 35% and 85% in steps of 5%.

ð The desired relative room humidity is indicated in the

segment display(20) for approx.5seconds. Then the current relative room humidity is displayed again.

Setting the fan speed

With this function you can choose between low, medium and high fan speed. The fan speed can only be adjusted in

dehumidification mode. The default setting for the laundry drying function is the highest level.

1. Repeatedly press the FAN button(22) to select a fan speed.

Continuous operation

The device dehumidifies the air constantly and regardless of the relative room humidity. The desired relative room humidity cannot be adjusted in this operating mode.

1. Press the MODE button(18) until the Cont. LED(14) is lit.

ð Continuous operation is selected.

Info

For continuous operation the condensation drain hose can be connected in order to continuously drain the accumulating condensate.

Comfort mode

Comfort mode ensures an agreeable humidity level ranging between 45% and 55%. Depending on the room temperature the device automatically regulates the convenient humidity level choosing a value from 45% – 50% – 55%.

In this operating mode it is not possible to regulate the humidity level manually.

1. Press the MODE button(18) until the Comfort LED(15) is lit to switch comfort mode on or off.

Setting the timer

For the device to switch on or off automatically after a predefined number of hours (max. 24hrs) you can programme the timer.

The timer can be programmed in increments of 0.5hours (0 to 10h) or in increments of 1hour (10 to 24h).

The timer can be set in all operating modes.

You can activate the function regardless of the device being switched on or off.

Note

Do not leave the operating device unattended in a freely accessible room with an activated timer.

8 EN

dehumidifier TTK 54 E

Page 9

Automatic switch-on

ü The device is switched off.

1. Press the TIMER button(23) to programme automatic switch-on.

ð The TIMER LED(10) is lit. ð The segment display(20) indicates the number of hours

until automatic switch-on. Standard: 0.0

2. Press the Increase value(19) and Decrease value buttons(21) to set a number of hours until automatic switch-on.

ð The number of hours is indicated on the segment

display(20) for approx.5s. Then the current humidity level of the room will be indicated.

ð The timer setting equals the desired number of hours. ð After the predefined time, the device switches itself on.

Automatic switch-off

ü The device is switched on.

1. Press the TIMER button(23) to programme automatic switch-off.

ð The TIMER LED(10) is lit. ð The segment display(20) indicates the number of hours

until automatic switch-off. Standard: 0.0

2. Press the Increase value(19) and Decrease value buttons(21) to set a number of hours until automatic switch-off.

ð The number of hours is indicated on the segment

display(20) for approx.5s. Then the current humidity level of the room will be indicated.

3. The device keeps running until the given switch-off time has expired or until the device is switched off manually.

ð The timer setting equals the desired number of hours. ð After the predefined time, the device switches itself off.

Auto stop function

If the water tank is full, not inserted correctly or the relative room humidity has been reached, the device will stop automatically.

Operation with hose attached to the condensation connection

For continuous operation or unattended dehumidification, please connect the supplied condensation drain hose to the device.

ü A suitable hose (diameter: 14mm) is ready for use. ü The device is switched off.

1. Remove the rubber plug.

2. Push one end of the hose onto the hose connection.

Note

You can deactivate automatic switch-on and switch-off by setting the respective number of hours back to 0 or by manually switching the device on or off. If error codeP2 is indicated on the segment display(20), the timer is also disabled. A full condensation tank can cause the device to be switched off before the set number of hours until automatic switch-off have elapsed.

Memory function

After a power failure during operation the device will automatically be switched back on after a while. The selected settings are saved. Any programmed timer settings will not be saved.

EN 9

dehumidifier TTK 54 E

Page 10

3. Guide the other hose end to a suitable drain or sufficiently dimensioned collection container. Please note that the hose must not be kinked.

Remove the hose if you want to collect the condensate in the condensation tank again. Allow the hose to dry prior to storage. The hose can be connected in any operating mode for continuous operation.

Automatic defrost

At low ambient temperatures, ice may form on the evaporator during dehumidification. The device will then carry out an automatic defrost. Dehumidification is briefly interrupted during defrosting. The fan keeps running. Error codeP1 for automatic defrost will be indicated on the segment display(20).

The duration of the defrost process can vary. Do not switch off the device during automatic defrost. Do not remove the mains plug from the mains socket.

Drying laundry

In addition, the device may also be used as a kind of clothes dryer to dry wet laundry in living or working spaces.

When positioning the device or a clothes horse, please observe the minimum distances specified in the technical data.

For drying laundry the following values should be selected:

• cupboard dry = 46 % relative humidity

• iron dry = 58 % relative humidity

• slightly dried = 65 % relative humidity

If necessary, use a measuring device to determine the humidity level.

The relative humidity cannot be adjusted in this operating mode.

The maximum operating time in this mode is 10hours.

1. Press the MODE button(18) until the Dryer LED(13) is lit.

ð The function for drying laundry is activated.

Shutdown

Warning of electrical voltage

Do not touch the mains plug with wet or damp hands.

• Switch off the device.

• Hold onto the mains plug while pulling the power cable out of the mains socket.

• If necessary, remove the condensation drain hose and any residual fluid from it.

• Empty the condensation tank, if need be.

• Clean the device according to the Maintenance chapter.

• Store the device according to the Storage chapter.

Errors and faults

The device has been checked for proper functioning several times during production. If malfunctions occur nonetheless, check the device according to the following list.

The device does not start:

• Check the power connection.

• Check the power cable and mains plug for damage.

• Check the on-site fusing.

• Check the filling level of the condensation tank and empty it if necessary. The Full LED(12) must not light up. Error codeP2 must not be indicated on the segment display(20).

• Check the condensation tank for correct seating.

• Check the room temperature. Observe the device's permissible operating range according to the technical data.

• Wait for 10minutes before restarting the device. If the device is not starting, have the electrics checked by a specialist company or by Trotec.

The device is running, but there is no formation of condensate:

• Check the float in the condensation tank for dirt. If necessary, clean the condensation tank. The float must be able to move freely.

• Check the room temperature. Observe the device's permissible operating range according to the technical data.

• Ensure that the relative room humidity complies with the technical data.

• Check the preselected relative room humidity. The humidity in the room must be above the selected range.

• Check the air filter for dirt. If necessary, clean or replace the air filter.

• Check whether the device is running in comfort mode. In this case, the compressor switches off automatically once the relative room humidity is below 45%.

10 EN

dehumidifier TTK 54 E

Page 11

• From the outside, check the condenser for dirt (see chapter Maintenance). If the condenser is dirty, have it cleaned by a specialist company or by Trotec.

• The device might carry out an automatic defrost. During automatic defrost, the device does not dehumidify.

The device is loud or vibrates:

• Check whether the device is set up in a stable and upright position.

Condensate is leaking:

• Check the device for leaks.

The compressor does not start:

• Check the room temperature. Observe the device's permissible operating range according to the technical data.

• Ensure that the relative room humidity complies with the technical data.

• Check the preselected relative room humidity. The humidity in the room must be above the selected range.

• Check whether the device is running in comfort mode. In this case, the compressor switches off automatically once the relative room humidity is below 45%.

• Check whether the overheating protection of the compressor has tripped. Disconnect the device from the mains and let it cool down for approx. 10minutes before reconnecting it.

• The device might carry out an automatic defrost. During automatic defrost, the device does not dehumidify.

Error codes

The following error messages can be displayed on the segment display(20):

Error code Cause Remedy

AS Fault at humidity

sensor

ES Fault at temperature

sensor

E3 General fault at the

device

EC Leaking refrigerant Switch the device off and

P1 Automatic defrost This is not a fault. Wait for a

P2 Condensation tank

full or not inserted correctly

Disconnect the device briefly from the mains. Should the error still be displayed after the restart, please contact the customer service.

contact the customer service.

brief period. The indication will disappear the moment the automatic defrost process is completed.

Empty the condensation tank or check the condensation tank for correct fit.

The device gets very warm, is loud or loses power:

• Check the air inlets and air filters for dirt. Remove external dirt.

• From the outside, check the device for dirt (see chapter Maintenance). If the inside of the device is dirty, have it cleaned by a specialist company for cooling and airconditioning or by Trotec.

Note

Wait for at least 3 minutes after maintenance and repair work. Only then switch the device back on.

Your device still does not operate correctly after these checks?

Please contact the customer service. If necessary, bring the device to a specialist company for cooling and air-conditioning or to Trotec for repair.

EN 11

dehumidifier TTK 54 E

Page 12

Maintenance

Maintenance intervals

Maintenance and care interval before every

start-up

Check the air inlets and outlets for

X X

dirt and foreign objects and clean if necessary

Clean the exterior

Visually check the inside of the device for dirt

Check the air filter for dirt and

X X

foreign objects and clean or replace if necessary

Replace the air filter

Check for damage

Check the attachment screws

Test run

Empty the condensation tank and/ or drain hose

Maintenance and care log

Device type: .............................................

as needed at least every

2weeks

X X

at least every 4weeks

at least every 6months

Device number: ....................................

at least annually

Maintenance and care interval

Check air inlets and outlets for dirt and foreign objects and clean if necessary

Clean the exterior

Visually check the inside of the device for dirt

Check the air filter for dirt and foreign objects and clean or replace if necessary

Replace the air filter

Check for damage

Check the attachment screws

Test run

Empty the condensation tank and/or drain hose

Comments

1. Date: ...................................

Signature: ................................

5. Date: ...................................

Signature: ................................

9. Date: ...................................

Signature: ................................

13. Date: .................................

Signature: ................................

2. Date: ....................................