Tripp Lite IS1000HG, IS1800HG, IS500HG, 93-2530 User Manual

0 (0)
Tripp Lite IS1000HG, IS1800HG, IS500HG, 93-2530 User Manual

IS Medical Grade

IMPORTANT SAFETY INSTRUCTIONS.

 

SAVE THESE INSTRUCTIONS.

Isolation Transformers

1111 W. 35th Street Chicago, IL 60609

Customer Support:

(773) 869-1234 www.tripplite.com

CAUTION!

DO not connect to an ungrounded outlet. DO not use with extension cords or adapters that eliminate the connection to ground. The isolation transformer is designed for indoor use only. Install the isolation transformer away from heat emitting appliances such as radiators or heat registers. Do not install where excessive moisture or other conductive contaminants are present. Do not use with life support appliances if a malfunction or failure could cause failure or significantly alter the performance of the life-support device. Do not use in the presence of a flammable anaesthetic mixture with air, oxygen or nitrous oxide.

Installation

1.Connect Your Isolation Transformer to Your AC Power Line

Plug the power cord into a standard, 3-wire grounded, 120V AC, 60 Hz utility outlet. Note: the isolation transformer only meets UL60601-1 when plugged into a hospital-grade outlet.

2. Connect Equipment to Your Isolation Transformer

Plug the AC power cords of your equipment into your isolation transformer. Do not use extension cords or adapters that eliminate the connection to ground. Connect equipment that requires a external connection to ground to the isolation transformer’s potential equalization conductor, labeled “ ” on the unit.

3. Turn Your Isolation Transformer On

Flip the lighted switch to provide clean AC power to the isolation transformer’s receptacles. “ ” is the ON position, “ ” the OFF.

Do not overload your isolation transformer. Excess load on the isolation transformer will cause one or both of its circuit breakers to trip; if it does, the outlets will cease to provide power. Reduce the load on the isolation transformer down to your unit’s Output Power rating by unplugging excess equipment, then depress the circuit breaker button(s) to reset the breaker(s) and restore power.

Maintenance

Your isolation transformer requires no routine maintenance. There are no user-serviceable parts inside your isolation transformer; do not open it for any reason.

Specifications

 

Output Power (Watts)

Outlets

 

IS250HG

250 W

2 NEMA 5-15RHG

IS500HG

500 W

4 NEMA 5-15RHG

IS1000HG

1000 W

4 NEMA 5-15RHG

IS1800HG

1800 W

6 NEMA 5-15/20RHG

Surge and Noise Suppression

Your isolation transformer is a surge suppressor that protects against surges on its input line and on its outlets. It also suppresses disruptive EMI/RFI line noise on the utility power line.

Medical/Hospital Grade Protection

(UL60601-1 Listed)

Your isolation transformer is UL60601-1 listed, classified as Class 1,Type B,Continuous Operation,Ordinary Equipment. The isolation transformer is Faraday-shielded and reduces the cumulative leakage currents of all connected equipment below 100 microamps. As a further safety measure, your isolation transformer is equipped with a hospital grade plug and receptacles to reduce the risk of accidental equipment disconnection.

2-Year Limited Warranty

Seller warrants this product, if used in accordance with all applicable instructions, to be free from original defects in material and workmanship for a period of 2 years from the date of initial purchase. If the product should prove defective in material or workmanship within that period, Seller will repair or replace the product, in its sole discretion. To obtain service under this warranty you must obtain a Returned Material Authorization (RMA) number from Tripp Lite or an authorized Tripp Lite service center. Products must be returned to Tripp Lite or an authorized Tripp Lite service center with transportation charges prepaid and must be accompanied by a brief description of the problem encountered and proof of date and place of purchase.

This warranty applies only to the original purchaser who must have properly registered the product within 10 days of purchase.

THIS WARRANTY DOES NOT APPLY TO NORMAL WEAR OR TO DAMAGE RESULTING FROM ACCIDENT, MISUSE, ABUSE OR NEGLECT. SELLER MAKES NO EXPRESS WARRANTIES OTHER THAN THE WARRANTY EXPRESSLY SET FORTH HEREIN. EXCEPT TO THE EXTENT PROHIBITED BY APPLICABLE LAW, ALL IMPLIED WARRANTIES, INCLUDING ALL WARRANTIES OF MERCHANTABILITY OR FITNESS, ARE LIMITED IN DURATION TO THE WARRANTY PERIOD SET FORTH ABOVE; AND THIS WARRANTY EXPRESSLY EXCLUDES ALL INCIDENTAL AND CONSEQUENTIAL DAMAGES.

WARNING: The individual user should take care to determine prior to use whether this device is suitable, adequate or safe for the use intended. Since individual applications are subject to great variation, the manufacturer makes no representation or warranty as to the suitability or fitness of these devices for any specific application.

Do not use Tripp Lite Isolation Transformers for life support devices in which a malfunction or failure of a Tripp Lite UPS System could cause failure or significantly alter the performance of a life-support device.

The policy of Tripp Lite is one of continuous improvement. Specifications are subject to change without notice.

Regulatory Compliance Identification Numbers

For the purpose of regulatory compliance certifications and identification, your Tripp Lite product has been assigned a unique series number. The series number can be found on the product nameplate label, along with all required approval markings and information. When requesting compliance information for this product, always refer to the series number. The series number should not be confused with the marking name or model number of the product.

This product designed and engineered in the USA.

Warranty Registration

Visit www.tripplite.com/warranty today to register the warranty for your new Tripp Lite product. You’ll be automatically entered into a drawing for a chance to win a FREE Tripp Lite product!*

*No purchase necessary. Void where prohibited. Some restrictions apply. See website for details.

IMPORTANTES CONSIGNES

IS Medical Grade

DE SÉCURITÉ. CONSERVEZ

Transformateurs d'isolation

CES INSTRUCTIONS EN LIEU SÛR.

 

1111 W. 35th Street • Chicago, IL 60609 USA

Service à la clientèle :

+1 (773) 869-1234 www.tripplite.com

MISE EN GARDE !

NE PAS relier à une prise non mise à la terre. NE PAS utiliser de rallonges électriques ou d'adaptateurs qui coupent la connexion de mise à la terre. Le transformateur d'isolation est conçu uniquement pour un usage intérieur. Installez le transformateur d'isolation loin des appareils producteurs de chaleur tels que les radiateurs ou les registres de chaleur. Ne l'installez pas en présence d'humidité excessive ou d'autres impuretés conductrices. Ne le raccordez pas à des appareils de maintien des fonctions vitales si leur dysfonction ou leur défaillance pourrait causer une panne ou pourrait modifier de manière significative l’exécution de ces dispositifs. Ne pas utiliser en présence d'un mélange anesthésique inflammable composé d'air, d'oxygène ou d'oxyde de nitrate.

Entretien

Votre transformateur d'isolation n'exige aucun entretien courant. Il n'y a pas de pièces à l'intérieur du transformateur d'isolation que l'utilisateur puisse réparer par lui-même ; ne l'ouvrez pas quelqu'en soit la raison.

Spécifications

 

Courant à la sortie (watts)

Prises

 

IS250HG

250

W

2 NEMA 5-15RHG

IS500HG

500

W

4 NEMA 5-15RHG

IS1000HG

1000

W

4 NEMA 5-15RHG

IS1800HG

1800

W

6 NEMA 5-15/20RHG

service autorisé Tripp Lite avec frais de transport prépayés et doivent être accompagnés d'une brève description du problème rencontré et d'une preuve de la date et de la place d'achat. Cette garantie ne s'applique qu'à l'acheteur original qui doit avoir enregistré le produit dans les dix jours de son achat.

CETTE GARANTIE NE S'APPLIQUE PAS À L'USURE NORMALE OU AUX DÉGÂTS CAUSÉS PAR UN ACCIDENT, UN EMPLOI ABUSIF OU À LA NÉGLIGENCE. LE VENDEUR NE DONNE AUCUNES GARANTIES EXPRESSES AUTRES QUE LA GARANTIE EXPRESSÉMENT ÉTABLIE ICI. SAUF DANS L'ÉTENDUE INTERDITE PAR LES LOIS APPLICABLES, TOUTES GARANTIES IMPLICITES, Y COMPRIS TOUTES GARANTIES DE COMMERCIABILITÉ OU DE CONVENANCE, SONT LIMITÉES EN DURÉE À LA PÉRIODE ÉTABLIE CI-DESSUS, ET CETTE GARANTIE EXCLUT EXPRESSÉMENT TOUS DÉGÂTS ACCIDENTELS OU CORRÉLATIFS.

Installation

1.Reliez votre transformateur d'isolation à votre ligne d'alimentation électrique c.a.

Branchez le cordon d'alimentation dans une prise de secteur c.a. trifilaire standard de 120 V à 60 Hz avec mise à la terre. Note : le transformateur d'isolation n'est conforme à la norme UL60601-1 que s'il est relié à une prise de qualité hôpital.

2.Reliez le matériel à votre transformateur d'isolation

Branchez les cordons d'alimentation c.a. de votre matériel sur votre transformateur d'isolation. N'utilisez pas de rallonges électriques ou d'adaptateurs qui coupent la connexion de mise à la terre. Reliez le matériel qui exige une connexion de mise à la terre externe à la barre de régulation de tension du transformateur d'isolation, marquée « » sur l'unité.

3.Mettez votre transformateur d'isolation sous tension

Appuyez sur l'interrupteur lumineux pour alimenter les bornes du

transformateur d'isolation en courant

c.a. sans parasite. « »

indique la position MARCHE et «

», la position ARRÊT.

Ne surchargez pas votre transformateur d'isolation. Toute surcharge du transformateur d'isolation provoquera le déclenchement d'au moins un de ses deux disjoncteurs, ce qui coupera l'alimentation électrique aux prises. Réduisez t-3>la charge du transformateur d'isolation au niveau de l'intensité nominale de votre unité en débranchant l'excès de matériel, puis appuyez sur les boutons des disjoncteurs déclenchés pour les ramener à leur position initiale et rétablir le courant.

Suppression de surtension et de bruit

Votre transformateur d'isolation est un suppresseur de surtension offrant une protection contre les surtensions sur sa ligne d'entrée et sur ses prises. Il supprime également le bruit de ligne sur l'alimentation secteur causé par des interférences électromagnétiques et du brouillage radioélectrique.

Protection de qualité Médicale/hôpital

(homologué UL60601-1)

Votre transformateur d'isolation est homologué UL60601-1, d e c l a s s e 1 , t y p e B , à f o n c t i o n n e m e n t c o n t i n u e t équipement standard. Le transformateur est doté d'une cage

de Faraday et réduit le taux de fuite de courant cumulatif de tout matériel branché à moins de 100 microampères. À titre de mesure de sécurité supplémentaire,votre transformateur d'isolation est muni d'une prise de courant et de bornes de qualité hôpital pour réduire le risque de déconnexion accidentelle du matériel.

GARANTIE LIMITÉE D'UN AN

Le vendeur garantit ce produit, quand il est utilisé selon les instructions applicables, être exempt de tout vice de matériel ou de fabrication pour une période de 1 an à partir de la date d'achat initial. Si le produit s'avérait avoir un vice de matériel ou de fabrication durant cette période, le Vendeur réparera ou remplacera le produit, à sa seule discrétion. Pour obtenir un service sous cette garantie, vous devez obtenir un numéro d'autorisation de renvoi de matériel (ARM) de Tripp Lite ou d'un centre de service autorisé Tripp Lite. Les produits doivent être renvoyés à Tripp Lite ou à un centre de

AVERTISSEMENT : L'utilisateur individuel devrait s'assurer de déterminer avant utilisation si cet appareil est approprié, adéquat ou sécuritaire pour l'usage prévu. Puisque les utilisations individuelles sont sujettes à d'importantes variations, le fabricant ne fait aucune déclaration ni n'émet aucune garantie de qualité commerciale ou d'adaptation à une utilisation particulière pour cet appareil.

Ne raccordez pas les Transformateurs d'isolation Tripp Lite à des appareils de maintien des fonctions vitales si leur dysfonction ou leur défaillance pourrait causer une panne ou pourrait modifier de manière significative l'exécution de ces dispositifs.

La politique de Tripp Lite vise à une amélioration constante des produits. Les spécifications ci-jointes peuvent être modifiées sans préavis.

Numéros d'identification de conformité aux règlements

À des fins de certification et d’identification de conformité aux règlements, votre produit Tripp Lite a reçu un numéro de série unique. Ce numéro se retrouve sur la plaque signalétique du produit, avec les inscriptions et informations d'approbation requises. Lors d'une demande d'information de conformité pour ce produit, utilisez toujours le numéro de série. Il ne doit pas être confondu avec le nom de la marque ou le numéro de modèle du produit.

Ce produit a été conçu et fabriqué aux États-Unis.

Loading...
+ 2 hidden pages