Trend DWS/DS10/F, DWS/DS12/F Additional information

Monocrystalline

Diamond Steels

DWS/DS10/F
DWS/DS12/F

DIAMOND STEELS
DWS/DS10/F - 10 inch
DWS/DS12/F - 12 inch

Thank you for purchasing this Trend product
which should give lasting performance if used
in accordance with these instructions.

The following symbol is used throughout these
instructions.

Denotes risk of personal injury, loss

of life or damage to the tool in case of
non-observance of the instructions.

SAFETY

Please read and understand these instructions
before use.

PLEASE KEEP THESE INSTRUCTIONS IN
A SAFE PLACE.

Users must be competent in using
woodworking equipment before using
our products. Ensure working position is
comfortable. Please keep children and visitors
away from tools and work area. All tools have
a residual risk, so must therefore be handled
with caution.

ENVIRONMENTAL PROTECTION

Recycle raw materials instead of disposing
as waste.

Packaging should be sorted for environmental­friendly recycling. The product and its
accessories at the end of its life should be
sorted for environmental-friendly recycling.

GUARANTEE

All Trend products guaranteed against any
defects in either workmanship or material,
except products that have been damaged due
to improper user or maintenance.

INST/DWS/DS v3.1

INTENDED USE

Diamond steels sharpen blunt knives easily
in seconds with little pressure applied. They
have an exceptional life span and will sharpen
both professional and domestic type blades.
Unlike a traditional steel which merely re-aligns
the edge (eventually leaving the blade rounded
and blunt) a diamond steel removes material
from the blade in each stroke maintaining a
sharp edge.

Ideal for domestic, butchery, catering and

n

fishing.

Diamond steel tools have a fine grade

n

with 600 grit (nom. 25 micron).

All cutting edges are very sharp and
care must be taken to prevent injury.

Never sharpen blades towards the
hand or body.

TECHNICAL DATA

Monocrystalline

diamonds

Pre-nickel plated

steel base

The monocrystalline diamonds are bonded
through an electroless process to a precision
ground pre-plated nickel stainless steel base.

Fine grade = 600 grit (nom. 25 micron)

w

diamonds

Nickel

Steel base

© Trend Machinery & Cutting Tools Ltd. 2014 E&OE
® All trademarks acknowledged

GB

Trend Machinery & Cutting Tools Ltd.

Tel: [phone]
[e-mail]
www.trend-uk.com

USA

Trend Routing Technology Inc.

Tel: [phone]
[e-mail]
www.trend-usa.com

RECYCLABLE

OPERATION

Correct Method of Sharpening a Knife

MAINTENANCE

Please only use Trend original spare parts and
accessories.
This product has been designed to operate over
a long period of time with minimum maintenance.
Continual satisfactory operation depends upon
proper care and regular cleaning.

Cleaning

n Clean with a damp cloth or use on a Trend

cleaning block Ref. DWS/CB/A.

n Hand wash only and dry thoroughly.

Lubrication

n Use dry only. Do not lubricate.

Storage

n Always return product to its packaging after

use.

1.

n Alternate strokes on either side of the

blade, slowly and softly at 20°. Bring
the knife down the length of the steel as
shown in the diagrams.

Use a shallow angle for a fine or filleting

n

edge. Use a steeper angle to achieve a
boning edge.

Clean with a damp cloth or a cleaning

n

block Ref. DWS/CB/A.

2.

20

n Serrated/scallop edged knives can be

sharpened by running the serrated edge
up and down the length of the steel.
Turn the blade over and wipe once on
the flat side to remove any burr created.

3.

Ensure tool and sharpener are held
securely when sharpening.

Ensure work height and position
is comfortable.

After use store sharpener carefully.

Our policy of continuous improvements mean that
specifications may change without notice. Trend
Machinery & Cutting Tools Ltd. cannot be held
liable for any material rendered unusable, or for
any form of consequential loss.