Transition Networks REDUNDANT E-FL-RED-SIC User Manual

32.11 Kb
Loading...

Specifications:

Fiber Connection:

 

ST type connectors (SMA type available

 

 

upon request)

Fiber Optic Cable Maximum Distance:

6,600 feet (2 kilometers)

Fiber Optic Cable Recommended:

62.5 / 125 µm multimode fiber

Optional

 

100 / 140 µm multimode fiber

 

 

85 / 125 µm multimode fiber

 

 

50 / 125 µm multimode fiber

Dimensions:

 

5.50” x 3.00” x 1.00”

 

 

(13.97cm x 7.62cm x 2.54cm)

Environment:

 

0–70 degrees C, 5%–90% humidity

 

 

non-condensing, 0–10,000 feet altitude

Limited Warranty:

 

Two years

LED's:

 

 

Fiber Port: Link -

Lit green LED indicates the Slide-In Card is receiving link

 

pulsed from a 10Base FL (or FOIRL) compliant device.

Enable -

Lit green LED indicates current link between fiber

 

connections. Only the active enable (1 or 2) LED will

 

appear.

 

Fault -

Lit red LED indicates a break in both fiber links 1 and 2.

SQE Switch:

The SQE (Signal Quality Error) heartbeat selection jumper can be positioned ON to enable the SQE or positioned OFF to disable the SQE. The SQE jumper is located on top of the transceiver printed wiring circuit board. The transceiver SQE is set to the OFF position at the factory. (Refer to Figure 1 on the front page of this guide.)

SQE Enable Position (ON): The transceiver SQE is positioned ON when connected to a workstation or DTE.

SQE Disable Position (OFF): The transceiver SQE is positioned OFF when connected to a Hub or Repeater.

Redundant 10BaseFL Slide-In Card User’s Guide

Model #: E-FL/RED-SIC

Manual #: 7339.B 5/94

About the Redundant 10BaseFL Slide-In Card:

The TRANSITION Networks, P/N E-FL/RED-SIC, is a slide-in card that provides a reliable backup feature for the fiber optic connection. The fiber optic cable can extend the transmission distance up to 6,600 feet (2 kilometers).

Figure 1 Crossview of the Fiber Redundant Slide-In Card

Installation Considerations:

Personnel can hot swap, install or remove a Slide-In Card with the hub unit power

The Slide-In cards can only be installed one way, with the components facing up. Carefully guide the Slide-In Card along the card guides, until the Slide-In Card flat connector and internal backplane meet. Carefully seat the connector into the backplane slot. Firmly push the card into the slot until the Slide-In Card face plat is flat against the back of the hub frame. Tighten the thumbscrews of the installed Slide-In Card into the threaded holes on the hub unit.

Technical Support:

For more information about this product or other TRANSITION Networks products your local TRANSITION Networks distributor.

Direct numbers are listed below:

 

 

TN Main Phone Numbers:

(800)

325-2725 or (612) 941-7600

TN Technical Support Number:

(800)

260-1312

TN Fax Number:

(612)

941-2322

FCC Regulations:

Note: This equipment has been tested and found to comply with the limits for a C digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to reasonable protection against harmful interference when the equipment is operate commercial environment. This equipment generates, uses, and can radiate radio f quency energy and, if not used in accordance with the

instruction manual, may cause harmful interference to radio communications. Op of this

equipment in a residential area is likely to cause harmful interference in which cas user will be required to correct the interference at his own cost.

Canadian Regulations:

Note: This digital apparatus does not exceed the Class A limits for radio noise for apparatus set out on the radio interference regulations of the Canadian Departmen Communications.

Trademark Notice:

Ethernet is a registered trademark of the Xerox Corporation, Inc. TRANSITION Networks is a trademark of TRANSITION Networks, Inc.

Re

P/N