Transition Networks POINTSYSTEM CPSMC0800-100, CPSMC0800-100 User Manual

778.32 Kb
Loading...

Transition Networks

CPSMC0800-100

8-Slot PointSystem™ Chassis

User’s Guide

(revision A)

CPSMC0800-100 PointSystem™ Chassis

Compliance Information

UL Listed

C-UL Listed (Canada)

CISPR22/EN55022 Class A + EN55024

CE Mark

FCC Regulations

This equipment has been tested and found to comply with the limits for a class A digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case the user will be required to correct the interference at the user’s own expense.

Canadian Regulations

This digital apparatus does not exceed the Class A limits for radio noise for digital apparatus set out on the radio interference regulations of the Canadian Department of Communications.

Le présent appareil numérique n'émet pas de bruits radioélectriques dépassant les limites applicables aux appareils numériques de la class A & B prescrites dans le Règlement sur le brouillage radioélectrique édicté par le ministère des Communications du Canada.

European Regulations Warning

This is a Class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures.

Achtung !

Dieses ist ein Gerät der Funkstörgrenzwertklasse A. In Wohnbereichen können bei Betrieb dieses Gerätes Rundfunkstörungen auftreten, in weichen Fällen der Benutzer für entsprechende Gegenmaßnahmen werantwortlich ist.

Attention !

Ceci est un produit de Classe A. Dans un environment domestique, ce produit risque de créer des interférences radioélectriques, il appartiendra alors à l’utilsateur de prende les measures spécifiques appropriées

CAUTION: THE RJ CONNECTORS ON THE INDIVIDUAL MEDIA CONVERTER SLIDE-IN-MODULES ARE NOT INTENDED FOR CONNECTION TO THE PUBLIC TELEPHONE NETWORK. Failure to observe this caution could result in damage to the public telephone network.

Der Anschluss dieses Gerätes an ein öffentlickes Telekommunikationsnetz in den EG-Mitgliedstaaten verstösst gegen die jeweligen einzelstaatlichen Gesetze zur Anwendung der Richtlinie 91/263/EWG zur Angleichung der Rechtsvorschriften der Mitgliedstaaten über Telekommunikationsendeinrichtungen einschliesslich der gegenseitigen Anerkennung ihrer Konformität.

Trademark Notice

All trademarks and registered trademarks are the property of their respective owners.

Copyright Restrictions

© 2003 Transition Networks.

All rights reserved. No part of this work may be reproduced or used in any form or by any means – graphic, electronic, or mechanical – without written permission from Transition Networks.

Printed in the U.S.A.

33270.A

Tech Support: 7am-6pm CST (GMT -6:00) 1-800-260-1312 International: 00-1-952-941-7600

2

CPSMC0800-100 PointSystem™ Chassis

Table of Contents

1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

1.1 Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

1.2 Unpacking the CPSMC0800-100 Equipment . . . . . . . . . . . . . . . . .5

2 Slide-in-Modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

2.1

Media Converter Slide-in-Modules . . . . . . . . . . . . . . . . . . . . . . . . .

6

 

2.1.1

Calculating Power Consumption . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

6

 

2.1.2 Installing Media Converter Slide-in-Modules . . . . . . . . . . . . . . . . . . . . .

7

 

2.1.3

Replacing Media Converter Slide-in-Modules . . . . . . . . . . . . . . . . . . . . .

8

2.2

Managment Modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

.9

 

2.2.1

Three Types of Management Modules . . . . . . . . . . . . . . . . . . . . . . . . .

.9

 

2.2.2 Installing the Management Modules . . . . . . . . . . . . . . . . . . . . . . . . . . .

10

 

2.2.3

Replacing the Management Modules . . . . . . . . . . . . . . . . . . . . . . . . . .

11

3 Powering the CPSMC0800-100 . . . . . . . . . . . . . . . . . . . . . . .12

3.1 Primary Power Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12

3.2 Auxilliary Power Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13

4 CPSMC0800-100 Chassis . . . . . . . . . . . . . . . . . . . . . . . . . . . .14

4.1 Installing the CPSMC0800-100 Chassis . . . . . . . . . . . . . . . . . . . .14

4.1.1 Standard 19-Inch Rack Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . .14

4.1.2 Table-Top Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15

4.2 Cascade Option . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16 4.3 Connecting the Slide-in-Modules to the Network . . . . . . . . . . . . .17 4.4 Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18

5

SNMP Agent in the Management Module . . . . . . . . . . . . . .

. 19

 

5.1

SNMP Hardware Connections . . . . . . . . . . . . . . . . . . . . . . . . . .

.19

 

5.2

SNMP Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

20

6

Fault Isolation and Correction . . . . . . . . . . . . . . . . . . . . . . . .

21

Technical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22

Cable Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23

Contact Us . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24

Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25

Tech Support: 7am-6pm CST (GMT -6:00) 1-800-260-1312 International: 00-1-952-941-7600

3

CPSMC0800-100 PointSystem™ Chassis

1 Introduction

1.1Description

The Transition Networks PointSystem™ CPSMC0800-100 is a 19-inch, rack-mount- able chassis for selected Transition Networks Media Converter Slide-In-Modules. The CPSMC0800-100 allows the network administrator to connect various copper and fiber-optic network media over protocols that include Ethernet, Fast Ethernet, DS3/E3, and OC-12. The CPSMC0800-100 provides installation space for up to eight (8) single-slot or four (4) dual-slot Media Converter Slide-in-Modules in the front of the unit.

Management Module Installed Slide-In-Module

Open Slot

Power Inlet

TXPWR

RXLNK

RESET

TERM

INIT

12C

12C-1

PWR

LKS

LKM

TX

 

RX

TX

 

RX

SPD PWR

FRX FLNK

CRX CLNK

TX

10/100SX

RX

10/100TX

CFETF110

 

 

 

 

 

 

 

 

50/60 Hz

 

 

 

 

DB-9

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Input Power:

 

 

 

 

 

 

 

 

 

 

 

Singlemode

 

 

Multimode

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

110-240 VAC

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

1.6A max. (60W max)

 

10BASE-T

 

INPORT

OUTPORT

MCCM10 MGMTMASTER

 

 

 

 

 

 

 

PWR

LKS

LKM

TX

Singlemode

RX

TX

Multimode

RX

 

SPD PWR

FRX FLNK

CRX CLNK

TX

10/100SX

RX

10/100TX

CFETF110

CPSMC-0800

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

8-Slot Chassis

introduction

The CPSMC0800-100 also comes equipped with an AC or DC power supply. An optional AC or DC power supply with Instant Fail Over operation is also available. The primary power supply is accessed through the Power Inlet on the front panel, while auxilliary power is accessed through the Auxilliary Power Inlet, located on the back panel.

Auxilliary Power Inlet

Four fans, two for the power supplies and two for the Slide-In-Modules, help remove heat from the chassis.

With installed PointSystem™ Management Module(s) (TN part number CPSMM120, -200, or -210), the CPSMC0800-100 can be managed and monitored via:

An SNMP application such as Transition Networks FocalPoint™ management software installed at a remote Network Management Station (NMS).

A remote Web browser.

A command-line interface (CLI) at an attached terminal.

A command-line-interface (CLI) at a remote Telnet connection.

The management features include:

Power control (slot on, slot off, in rush limit) for each individual slot.

Internal temperature monitor.

Fan failure monitor.

Chassis power consumption monitor.

Power supply type identification.

Power supply condition monitor.

Fail-over power detection.

The Management Modules also make it possible to control up to eight (8) cascaded CPSMC0800-100 chassis, which can accomodate up to 55 installed Media Converter Slide-in-Modules.

Tech Support: 7am-6pm CST (GMT -6:00) 1-800-260-1312 International: 00-1-952-941-7600

4

CPSMC0800-100 PointSystem™ Chassis

2.1Unpacking the CPSMC0800-100 Equipment

Use the following list to verify the shipment:

 

Item

Part Number

8-Slot chassis with AC power supply

CPSMC0800-100

8-Slot chassis with DC power supply

CPSMC0810-100

Power Cord

(varies by country)

External AC Power Supply

CPSMP-180 (optional)

External DC Power Supply

CPSMP-190 (optional)

1-slot Master Management Module

CPSMM-100 (optional)

2-slot Master Management Module

CPSMM-200 (optional)

FocalPoint™ Software Disk

FPS (provided with CPSMM-200)

Expansion Management Module

CPSMM-210 (optional)

Management Module Cascade Connector

6026 (optional)

Rack Mount Ears

CPSRE-238 (optional)

Selectable Media Converter Slide-in-Module(s)

(various P/N) - (optional)

User’s Guide

33270

introduction

Tech Support: 7am-6pm CST (GMT -6:00) 1-800-260-1312 International: 00-1-952-941-7600

5

CPSMC0800-100 PointSystem™ Chassis

2 Slide-in-Modules

2.1Media Converter Slide-in-Modules

Transition Networks Media Converter Slide-in-Modules, installed in slots at the front of the chassis, allow the network administrator to connect various copper and fiberoptic network media over protocols that include Ethernet, Fast Ethernet, DS3/E3, and OC-12 as well as many others (see www.transition.com for a complete listing.)

NOTE: Refer to the documentation that comes with each Media Converter Slide-in- Module for cable, connector, and LED indicator information specific to that Media Converter Slide-in-Module.

2.1.1Calculating the Power Consumption

CAUTION: Before installing the Media Converter Slide-in-Modules, refer to the power consumption data for each individual Media Converter Slide-in-Module (provided in the User’s Guide shipped with each Media Converter Slide-in- Module). The combined power consumption of all devices must not exceed the available power supply. Failure to observe this caution could result in diminishing system reliability.

In other words, the combined wattage of the CPSMC0800-100 8-Slot chassis plus all Slide-In-Modules must be less than the available power.

Contact Transition Networks Tech Support to ensure the power requirements for your specific application do not exceed the available power.

modules-in-slide

Tech Support: 7am-6pm CST (GMT -6:00) 1-800-260-1312 International: 00-1-952-941-7600

6

CPSMC0800-100 PointSystem™ Chassis

2.1.2Installing the Media Converter Slide-in-Modules

CAUTION: Wear a grounding device and observe electrostatic discharge precautions when installing the Media Converter Slide-in-Module(s) into the chassis. Failure to observe this caution could result in damage to, and subsequent failure of, the Media Converter Slide-in-Module(s).

NOTE: Media Converter Slide-in-Modules can be installed in any installation slot, in any order.

To install the Media Converter Slide-in-Module into the CPSMC0800-100 8-Slot chassis:

1.Remove the Media Converter Slide-in-Module protective plate from the installation slot by removing the one (1) screw that secures the plate to the front of the chassis.

NOTE: If the Slide-in-Module requires two slots, remove the protective plates from two (2) adjacent installation slots.

2.Align the Media Converter Slide-in-Module with the chassis installation slot so that the panel fastener screw is at the left of the Media Converter Slide-in- Module.

TXPWR

RXLNK

RESET

TERM

INIT

12C

12C-1

PWR

LKS

LKM

TX

 

RX

TX

 

RX

SPD PWR

FRX FLNK

CRX CLNK

TX

10/100SX

RX

10/100TX

CFETF110

 

 

 

 

 

 

50/60 Hz

 

 

 

 

DB-9

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Input Power:

 

 

 

 

 

 

 

 

 

 

 

Singlemode

 

 

Multimode

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

110-240 VAC

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

1.6A max. (60W max)

 

10BASE-T

 

INPORT

OUTPORT

MCCM10 MGMT MASTER

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

PWR

FLNK

CLNK

RX

10/100TX

CFETF110

CPSMC-0800

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

8-Slot Chassis

PWR

 

 

 

 

 

 

 

LKS

LKM

TX

Singlemode

RX

TX

Multimode

RX

Panel Fastener Screw

3.Carefully slide the Media Converter Slide-in-Module into the installation slot.

NOTE: Ensure that the Media Converter Slide-in-Module is firmly seated against the back of the chassis.

4.Install the Media Converter Slide-in-Module by carefully rotating the attached panel fastener screw clockwise to secure the Media Converter Slide-in-Module to the chassis.

5.Repeat steps 1 through 4 for additional Media Converter Slide-in-Module(s).

modules-in-slide

Tech Support: 7am-6pm CST (GMT -6:00) 1-800-260-1312 International: 00-1-952-941-7600

7

CPSMC0800-100 PointSystem™ Chassis

2.2.3Replacing the Media Converter Slide-in-Modules

CAUTION: Wear a grounding device and observe electrostatic discharge precautions when replacing Media Converter Slide-in-Module(s). Failure to observe this caution could result in damage to, and subsequent failure of, the Media Converter Slide-in-Module(s).

NOTE: The Media Converter Slide-in-Modules are hot-swappable.

To replace a Media Converter Slide-in-Module:

1.Remove the Media Converter Slide-in-Module to be replaced by loosening the one (1) screw that secures the Slide-in-Module to the CPSMC0800-100 chassis front. Slide the Media Converter Slide-In-Module from the CPSMC0800-100 chassis.

2.Align the replacement Media Converter Slide-in-Module with the chassis installation slot so that the panel fastener screw is to the left.

TXPWR

RXLNK

RESET

TERM

INIT

12C

12C-1

PWR

LKS

LKM

TX

 

RX

TX

 

RX

SPD PWR

FRX FLNK

CRX CLNK

TX

10/100SX

RX

10/100TX

CFETF110

 

 

 

 

 

 

50/60 Hz

 

 

 

 

DB-9

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Input Power:

 

 

 

 

 

 

 

 

 

 

 

Singlemode

 

 

Multimode

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

110-240 VAC

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

1.6A max. (60W max)

 

10BASE-T

 

INPORT

OUTPORT

MCCM10 MGMT MASTER

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

PWR

FLNK

CLNK

RX

10/100TX

CFETF110

CPSMC-0800

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

8-Slot Chassis

PWR

 

 

 

 

 

 

 

LKS

LKM

TX

Singlemode

RX

TX

Multimode

RX

Panel Fastener Screw

3.Carefully slide the replacement Media Converter Slide-in-Module into the installation slot.

NOTE: Ensure that the Media Converter Slide-in-Module is firmly seated against the back of the chassis.

4.Install the replacement Media Converter Slide-in-Module by carefully rotating the attached panel fastener screw clockwise to secure the Media Converter Slide-in-Module to the chassis.

modules-in-slide

Tech Support: 7am-6pm CST (GMT -6:00) 1-800-260-1312 International: 00-1-952-941-7600

8

+ 18 hidden pages