Transition Networks Milan MIL-SM2401MAF User Manual

1.17 Mb
Loading...

MIL-SM2401MAF

24-Port 10/100 BASE-TX POE

Two combo ports

10/100/1000BASE-T/1000Base-X SFP Advanced Managed Switch

USER GUIDE

Rev.1.01

Nov-2009

FCC Warning

This Equipment has been tested and found to comply with the limits for a Class-A digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy. It may cause harmful interference to radio communications if the equipment is not installed and used in accordance with the instructions. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna

Increase the separation between the equipment and receiver

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected

Consult the dealer or an experienced radio/TV technician for help

CE Mark Warning

This is a Class-A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures.

Transition Networks

 

MIL-SM2401MAF

Contents

 

 

FCC Warning.................................................................................................................

 

i

CE Mark Warning

..........................................................................................................

i

INTRODUCTION ..........................................................................................................

 

1

Features .......................................................................................................................

 

1

Software Features ........................................................................................................

2

Package Contents ........................................................................................................

6

HARDWARE DESCRIPTION.......................................................................................

7

Physical Dimension ......................................................................................................

7

Front Panel...................................................................................................................

 

7

LED Indicators ..............................................................................................................

 

8

Rear Panel..................................................................................................................

 

10

Desktop Installation ....................................................................................................

10

Attaching Rubber Pads........................................................................................

10

Rack-mounted Installation ..........................................................................................

11

Power On....................................................................................................................

 

11

NETWORK APPLICATION........................................................................................

12

Small Workgroup ........................................................................................................

 

12

Segment workgroup....................................................................................................

13

DC Power Input ..........................................................................................................

 

14

CONSOLE MANAGEMENT.......................................................................................

15

Connecting to the Switch............................................................................................

15

Login in the Console Interface....................................................................................

15

CLI Management ........................................................................................................

 

16

Commands Level.................................................................................................

16

Commands Set List .............................................................................................

18

 

System Commands Set .................................................................

18

 

Port Commands Set.......................................................................

21

 

Trunk Commands Set ....................................................................

25

24-Hour Technical Support: 1-800-260-1312

International: 00-1-952-941-7600

i

Transition Networks

 

MIL-SM2401MAF

 

VLAN Commands Set....................................................................

26

 

Spanning Tree Commands Set......................................................

31

 

QOS Commands Set .....................................................................

35

 

IGMP Commands Set ....................................................................

37

 

Mac / Filter Table Commands Set..................................................

38

 

SNMP Commands Set...................................................................

40

 

Port Mirroring Commands Set........................................................

41

 

802.1x Commands Set...................................................................

42

 

TFTP Commands Set ....................................................................

45

 

UPS Commands Set......................................................................

46

 

PoE Commands Set.......................................................................

47

 

System log Commands Set............................................................

48

 

SNTP Commands Set....................................................................

49

WEB-BASED MANAGEMENT...................................................................................

50

About Web-based Management .................................................................................

50

Preparing for Web Management.................................................................................

50

System Login..............................................................................................................

 

50

Port status ..................................................................................................................

 

51

View the Port Information ....................................................................................

53

Port Statistics..............................................................................................................

 

53

Administrator ..............................................................................................................

 

54

IP Address...........................................................................................................

 

55

Switch Setting......................................................................................................

55

Basic ............................................................................................................

 

55

Advanced .....................................................................................................

56

Misc Configuration........................................................................................

58

Console Port Information.....................................................................................

59

Port Controls........................................................................................................

 

60

Trunking ..............................................................................................................

 

61

Aggregator setting........................................................................................

61

Aggregator Information.................................................................................

63

24-Hour Technical Support: 1-800-260-1312

International: 00-1-952-941-7600

 

ii

 

Transition Networks

MIL-SM2401MAF

 

Aggregator State Activity..............................................................................

64

Forwarding and Filtering......................................................................................

65

 

IGMP Snooping............................................................................................

65

 

Static MAC Address .....................................................................................

66

VLAN configuration..............................................................................................

68

 

Port-based VLAN .........................................................................................

68

 

802.1Q VLAN ...............................................................................................

71

Spanning Tree.....................................................................................................

76

 

System Configuration ...................................................................................

77

 

Per Port Configuration..................................................................................

78

Port Mirroring.......................................................................................................

80

SNMP Management ............................................................................................

82

Security Manager ................................................................................................

83

SNTP Configuration.............................................................................................

84

802.1X Configuration...........................................................................................

85

 

System Configuration ...................................................................................

85

 

Per port Configuration ..................................................................................

86

 

Misc Configuration........................................................................................

87

System Log..........................................................................................................

87

Save Configuration..............................................................................................

89

TFTP Update Firmware ..............................................................................................

89

Configuration Backup .................................................................................................

90

TFTP Restore Configuration................................................................................

90

TFTP Backup Configuration ................................................................................

91

Factory Default ...........................................................................................................

91

System Reboot ...........................................................................................................

92

Power Status ..............................................................................................................

92

PoE Status..................................................................................................................

93

TROUBLESHOOTING ...............................................................................................

96

Incorrect connections..................................................................................................

96

 

Faulty or loose cables ...........................................................................

96

 

Non-standard cables .............................................................................

96

24-Hour Technical Support: 1-800-260-1312

International: 00-1-952-941-7600

 

 

iii

Transition Networks

MIL-SM2401MAF

 

Improper Network Topologies ...............................................................

97

Diagnosing LED Indicators .........................................................................................

97

Diagnosing PoE problems ..........................................................................................

97

TECHNICAL SPECIFICATION ................................................................................

100

APPENDIX

...............................................................................................................

103

Console Port .................................................................................Pin Assignments

103

Cables ......................................................................................................................

 

104

100BASE-TX/10BASE ...............................................................-T Pin Assignments

104

2 Gigabit Copper/SFP .......................................................(mini-GBIC) combo port:

105

24-Hour Technical Support: 1-800-260-1312

International: 00-1-952-941-7600

iv

Transition Networks

MIL-SM2401MAF

Introduction

The 24 10/100TX plus 2 Mini-GBIC/Copper managed PoE switch is a multi-port Switch that can be used to build high-performance switched workgroup networks. This switch is a store-and-forward device that offers low latency for high-speed networking and allows the switch to auto-learn and store source address in an 8K-entry MAC address table. The switch is targeted at workgroup, department or backbone computing environment.

The 24 10/100TX plus 2 Mini-GBIC/Copper managed PoE switch has 24x auto-sensing 10/100Base-TX RJ-45 ports and all ports support PoE injector function. The switch has 2 auto-detected Giga port for higher connection speed. Also, the switch provides one extra 48VDC power input for the power supply input connection.

Features

24 10/100 plus 2 Mini-GBIC /Gigabit Copper combo switch with 24 PoE injectors and build in 200W AC power

Confirms to IEEE802.3 10BASE-T, 802.3u 100BASE-TX, 802.3ab 1000BASE-T, 802.3z Gigabit Fiber, 802.3af Power over Ethernet

Provides extra DC 48V input with redundant function and management power status through RS-232 port

High Back-Plane bandwidth 8.8Gbps

Supports IEEE802.1w Rapid Spanning Tree

Supports IGMP Snooping and IGMP Query mode for Multi-media application

Port Mirror and Bandwidth Control supported

Supports GVRP function

End point insert mode remote power feeding

Supports IEEE802.3x Flow Control

Flow Control with full duplex

24-Hour Technical Support: 1-800-260-1312

International: 00-1-952-941-7600

1

Transition Networks

MIL-SM2401MAF

Back Pressure with half duplex

Supports Port Based VLAN /802 .1Q Tag VLAN

Supports IEEE802.3ad Port Trunk with LACP

Supports Spanning Tree protocol IEEE 802.1d

Supports IEEE 802.1p Class of Service

Supports IEEE 802.1x User Authentication

Supports Broadcast Storm Filter

Supports DHCP Client

Supports SNTP

Supports System Event Log

Management by Web/SNMP/Telnet/Console

Software Features

 

SNMP management

 

Telnet management

Management

Web management

 

RS-232 terminal console for command line interface

 

management

 

 

 

RFC 1157 SNMP

 

RFC 1213 MIB II

 

RFC 1643 Ethernet like

SNMP MIB

RFC 1493 Bridge MIB

RFC 2674 VLAN MIB

 

 

private MIB

 

RFC 1628 UPS MIB

 

RFC3621 Power Ethernet MIB

 

 

 

 

24-Hour Technical Support: 1-800-260-1312

International: 00-1-952-941-7600

2

Transition Networks

MIL-SM2401MAF

Cold start

Link down

Link up,

Type of Trap

Authorization fail

Trap stations up to 3

Private trap for power supply device

RFC 2030 SNTP

RFC 2821 SMTP (option)

RFC Standard RFC 1492 TACACS+ (option)

RFC 1215 Trap

RFC 1757 RMON 1

TFTP

Software Upgrade

Console

Support IEEE802.3ad with LACP function

Up to 7 trunk groups and group members up to 4

Port Trunk

The trunk port within 24-port 10/100TX and extension module

IEEE802.1d Spanning Tree

Spanning Tree

IEEE802.1w Rapid Spanning Tree

Port based VLAN

IEEE802.1Q Tag VLAN

VLAN

VLAN groups up to 256

The VLAN ID can be assigned from 1 to 4094

Per system supports high and low queues

The priority service rule: first come first service, all High

Class of Service

before Low, WRR for High or low weight

24-Hour Technical Support: 1-800-260-1312

International: 00-1-952-941-7600

3

Transition Networks MIL-SM2401MAF

 

Supports 3 settings: Disable, Low or High priority

Port Based Priority

When set to “Disable”, the income packet will follow QOS

policy; Otherwise, the packet will follow port priority

 

 

setting to “High/Low” queue

 

 

IGMP

IGMP snooping for multimedia application and supports

256 groups

 

 

 

Port Security

Ingress and egress MAC address filter and static source

MAC address lock

 

 

 

 

Global system supports 3 mirroring types: RX, TX and

Port Mirror

Both packet

 

The maximum of port mirror entries is up to 25

 

 

Bandwidth Control

Per port supports bandwidth control

Per level 100Kbps

 

 

 

 

IEEE802.1x User-Authentication and can report to

 

RADIUS server

802.1x Authentication

 

Reject

 

Accept

 

 

 

Authorize

 

 

Disable

 

 

DHCP

DHCP client

 

 

 

Packet filter

Broadcast storm filter

 

 

 

 

 

 

24-Hour Technical Support: 1-800-260-1312

International: 00-1-952-941-7600

4

Transition Networks MIL-SM2401MAF

 

Null: no PD presents

Fault status detect

Overload: current support over 475mA @ DC 48V and

over 50 milliseconds

 

 

DR fail: PD discovery resistor is not in the limited range

 

 

 

Displays current PD parameters:

 

Discover-resistor detected value

Parametric

 

Current

 

Voltage

information

 

Power consumption

 

 

 

Classification current

 

 

Determined class

 

 

 

Port Disable/Enable

Port configuration

PD detect control (enable/disable)

control

Classification detect control (enable/disable)

 

DC disconnect detect control

 

 

 

System detects status:

Mode status

 

I –sample

 

V-sample

 

 

 

R-detect

 

 

SNTP

RFC 2030 Simple Network Time Protocol

 

 

 

SMTP

RFC2821 Simple Mail Transfer protocol (option)

 

 

 

System Log

System Log record up to 1000 entries

 

 

 

 

 

 

24-Hour Technical Support: 1-800-260-1312

International: 00-1-952-941-7600

5

Transition Networks

MIL-SM2401MAF

Power supply monitoring function for AC power, DC

power

Power monitor

Additional DC power supply can be installed with PoE switch, and PoE-UPWM

Power testing

Supports power supply testing (CLI)

 

 

Package Contents

Unpack the contents of the 24 10/100TX plus 2 Mini-GBIC/Copper managed PoE switch and verifies them against the checklist below:

24 10/100TX plus 2 Mini-GBIC/Copper managed PoE switch x 1

Power Cord x 1

Rubber Pad x 1

Rack-mounted kit x 1

RS-232 cable x 1

User Manual x 1

Compare the contents of the 24 10/100TX plus 2 Mini-GBIC/Copper managed PoE switch package with the standard checklist above. If any item is missing or damaged, please contact the local dealer for exchanging.

24-Hour Technical Support: 1-800-260-1312

International: 00-1-952-941-7600

6

Transition Networks

MIL-SM2401MAF

Hardware Description

This chapter mainly describes the hardware of the 24 10/100TX plus 2 Mini-GBIC/Copper managed PoE switch and gives a physical and functional overview on the certain switch.

Physical Dimension

The physical dimension of 24 10/100TX plus 2 Mini-GBIC/Copper managed PoE switch is 440mmx 280mm x 44mm (W x D x H)

Front Panel

The front panel of the 24 10/100TX plus 2 Mini-GBIC/Copper managed PoE switch consists of 24x 10/100Base-TX RJ-45 ports (Auto MDI/MDIX), 2 auto-detected Gigabit Copper/Mini-GBIC ports, and one console port. The LED Indicators are also located on the front panel of the Switch.

Front panel of the 24 10/100TX plus 2 Mini-GBIC/Copper managed PoE switch

RJ-45 Ports (Auto MDI/MDIX): 24x 10/100 N-way auto-sensing for 10Base-T or 100Base-TX connections.

In general, MDI means connecting to another Hub or Switch while MDIX means connecting to a workstation or PC. Therefore, Auto MDI/MDIX would allow connecting to another Switch or workstation without changing non-crossover or

24-Hour Technical Support: 1-800-260-1312

International: 00-1-952-941-7600

7

Transition Networks

MIL-SM2401MAF

crossover cabling.

2 Giga port: Traditional RJ-45 ports can be used for uplinking wide-band paths in short distance (< 100 m), or the appropriate replaceable mini-GBIC ports can be used for the application of wideband uplinking and long distance transmissions to fit the field request flexibly.

LED Indicators

The LED indicators display a real-time indication of systematic operation status. There are three LED-Indicators (Link/Activity, Full duplex, power forwarding) for each UTP port and one power LED for the system unit. The following table provides descriptions of the LED statuses and meaning.

 

 

 

LED indicators

 

 

 

 

 

LED

Status

Description

 

 

 

 

 

 

Green

Power On

 

Power

 

 

 

 

OFF

Power is not connected

 

 

 

 

 

LNK/ACT

Green

The port is connecting with the device.

 

 

 

 

 

 

 

 

24-Hour Technical Support: 1-800-260-1312

International: 00-1-952-941-7600

 

 

 

8

Transition Networks

MIL-SM2401MAF

 

 

 

 

 

 

 

 

BLINK

The port is receiving or transmitting data.

 

 

 

 

 

 

 

 

OFF

No device attached.

 

 

 

 

 

 

 

 

 

 

 

 

 

Orange

The port is operating in Full-duplex mode.

 

 

FDX

 

 

 

 

 

OFF

In Half-duplex mode

 

 

 

 

 

 

 

 

Green

The PoE Injector function is on and power is

 

 

 

forwarding the attached PD device

 

 

 

 

 

 

Power Forwarding

 

 

 

 

 

OFF

The PoE injector function disables

 

 

 

 

 

 

 

 

Green

The port is connecting with the device and

 

 

 

operating at speed of 1000Mbps

 

 

 

 

 

 

 

 

 

 

 

 

Orange

The port is connecting with the device and

 

 

 

operating at speed of 100Mbps

 

 

LNK/ACT (25 & 26

 

 

 

 

 

 

 

port /Giga port)

 

 

 

 

 

 

 

 

 

BLINK

The port is receiving or transmitting data.

 

 

 

 

 

 

 

 

OFF

No device attached

 

 

 

 

 

 

 

FDX/COL (25 & 26

Orange

The port is operating in Full-duplex mode

 

 

port /Giga port)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

24-Hour Technical Support: 1-800-260-1312

International: 00-1-952-941-7600

 

 

 

 

9

Transition Networks

MIL-SM2401MAF

BLINK

Collision of Packets occurs in the port

OFF

In Half-duplex mode

Rear Panel

The two fans, two console ports, and the 3-pronged power plugs are located at the rear panel of 24 10/100TX plus 2 Mini-GBIC/Copper managed PoE switch shown as below. The switch also provides one DC 48V input for the extra power connection and one DC 48V internal power supply for the power redundant. The two-console ports are for connecting with UPS device to manage UPS device or connect with the power supply device for managing it.

The rear panel of the 24 10/100TX plus 2 Mini-GBIC/Copper managed PoE switch

Desktop Installation

Set the switch on a sufficiently large flat space with a power outlet nearby. The surface where you put your switch should be clean, smooth, level and sturdy. Make sure there is enough clearance around the switch to allow attachment of cables, power cord and allow air circulation.

Attaching Rubber Pads

1.Make sure mounting surface on the bottom of the switch is grease and dust free.

24-Hour Technical Support: 1-800-260-1312

International: 00-1-952-941-7600

10

Transition Networks

MIL-SM2401MAF

2.Remove adhesive backing from the Rubber Pads.

3.Apply the Rubber Pads to each corner on the bottom of the switch. These footpads can prevent the switch from shock/vibration.

Rack-mounted Installation

The switch come with a rack-mounted kit and can be mounted in an EIA standard size, 19-inch Rack. The switch can be placed in a wiring closet with other equipment. Perform the following steps to rack mount the switch:

1.Position one bracket to align with the holes on one side of the switch and secure it with the smaller bracket screws. Then attach the remaining bracket to the other side of the switch.

2.After attaching both mounting brackets, position the 24 10/100TX plus 2 Mini-GBIC/Copper managed PoE switch in the rack by lining up the holes in the brackets with the appropriate holes on the rack. Secure the switch to the rack with a screwdriver and the rack-mounting screws.

[Note] For proper ventilation, allow about at least 4 inches (10 cm) of clearance on the front and 3.4 inches (8 cm) on the back of the switch. This is especially important for enclosed rack installation.

Power On

Connect the power cord to the power socket on the rear panel of the switch. The other side of power cord connects to the power outlet. The internal power supply of the Switch works with AC voltage range of 100-240V and Frequency of 50~60Hz. Check the power indicator on the front panel to see if power is properly supplied.

24-Hour Technical Support: 1-800-260-1312

International: 00-1-952-941-7600

11

Transition Networks

MIL-SM2401MAF

Network Application

This section provides a few samples of network topology in which the switch is used. In general, the 24 10/100TX plus 2 Mini-GBIC/Copper managed PoE switch with its large address table (8K MAC address) and high performance are ideal for interconnecting networking segments.

PC, workstations, and servers can communicate each other by directly connecting with 24 10/100TX plus 2 Mini-GBIC/Copper managed PoE switch. The switch automatically learns node addresses, which are subsequently used to filter and forward all traffic based on the destination address.

24 10/100TX plus 2 Mini-GBIC/Copper managed PoE switch provides PoE injector function on every Ethernet port which can provide the power to the PD device, such as AP or switch. It can solve the problem of the PD device position limitation of power supply.

Using Uplink port, the Switch can connect with another switch or hub to interconnect other small-switched workgroups to form a larger switched network. Meanwhile, you can also use fiber ports to connect switches.

Small Workgroup

24 10/100TX plus 2 Mini-GBIC/Copper managed PoE switch can be used as a standalone switch to which personal computers, server, printer server, are directly connected to form a small workgroup.

24-Hour Technical Support: 1-800-260-1312

International: 00-1-952-941-7600

12

Transition Networks

MIL-SM2401MAF

Small Workgroup Application

Segment workgroup

For enterprise networks where large data broadcasts are constantly processed, this switch is an ideal solution for department users to connect to the corporate backbone.

In the illustration below, two managed PoE switches with PCs, print server, local server, wireless AP (IEEE 802.3af compliant), and IP camera (IEEE 802.3af compliant) attached are both connect to the core switch. All the devices in this network can communicate with each other through the core switch.

Segment workgroup Application

24-Hour Technical Support: 1-800-260-1312

International: 00-1-952-941-7600

13

Transition Networks

MIL-SM2401MAF

DC Power Input

The 24 10/100TX plus 2 Mini-GBIC/Copper managed PoE switch has a DC 48V power input for the extra power supply connection. The DC 48V power input can be used as a power backup when the AC power is down or no AC power supply in the installation. The AC power and the DC 48V power can be connected at the same time, but the switch will use the DC 48V as the master power input and the AC power as the secondary or backup power input. The following figures are example of the application. In the figure, the DC 48V power input connects with the power supply device and through the RS-232 connection to manage the power supply device.

24-Hour Technical Support: 1-800-260-1312

International: 00-1-952-941-7600

14

Transition Networks

MIL-SM2401MAF

Console Management

Connecting to the Switch

The console port is a female DB-9 connector that enables a connection to a PC or terminal for monitoring and configuring the Switch. Use the supplied RS-232 cable with a male DB-9 connector to connect a terminal or PC to the Console port. The Console configuration (out of band) allows users to set switch for remote terminal as if the console terminal were directly connected to it.

Login in the Console Interface

When the connection between switch and PC is ready, turn on the PC and run a terminal emulation program or Hyper Terminal and configure its communication parameters to match the following default characteristics of the console port:

Baud Rate: 9600 bps

Data Bits: 8

Parity: none

Stop Bit: 1

Flow control: None

The settings of communication parameters

After finishing the parameter settings, click “OK“. When the blank screen shows up, press Enter key to bring out the login prompt. Key in the ‘root’ (default value) for the

24-Hour Technical Support: 1-800-260-1312

International: 00-1-952-941-7600

15

Transition Networks

MIL-SM2401MAF

both User name and Password (use Enter key to switch), then press Enter key and the Main Menu of console management appears right after as below. The figure shown below is a login screen:

Console login screen

CLI Management

The system supports console management—CLI command. After logging in to the system, a command prompt shows up. To enter CLI management interface, enter “enable” command. The following tables list the CLI commands and description.

Commands Level

 

Modes

 

Access

 

Prompt

 

 

Exit Method

 

 

About This Mode

 

 

 

Method

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

The user commands

 

 

 

Begin a

 

 

Enter logout

 

available at the user

 

User EXEC

session with

switch>

 

 

level are a subset of

 

 

or quit.

 

 

 

 

your switch.

 

 

 

 

 

those available at the

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

privileged level.

 

 

 

 

 

 

24-Hour Technical Support: 1-800-260-1312

 

International: 00-1-952-941-7600

 

 

 

16

 

 

 

 

 

 

 

Transition Networks

 

 

 

MIL-SM2401MAF

 

 

 

 

 

 

 

 

 

 

 

Use this mode to

 

 

 

 

 

• Perform basic tests.

 

 

 

 

 

• Display system

 

 

 

 

 

information.

 

 

 

 

 

 

 

 

 

 

 

The privileged

 

 

Enter the

 

 

command is advance

Privileged

 

enable

 

Enter disable

mode

 

command

switch#

Privileged this mode to

EXEC

 

to exit.

 

while in user

 

• Display advance

 

 

 

 

 

 

EXEC mode.

 

 

function status

 

 

 

 

 

• Save configures

 

 

 

 

 

 

 

 

Enter the

 

To exit to

 

 

 

configure

 

Use this mode to

Global

 

 

privileged

 

command

switch

configure parameters

Configuratio

 

EXEC mode,

 

while in

(config)#

that apply to your

n

 

enter exit or

 

privileged

 

switch as a whole.

 

 

 

end

 

 

EXEC mode.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Enter the vlan

 

 

 

 

 

database

 

To exit to user

Use this mode to

VLAN

 

command

switch

configure

 

EXEC mode,

database

 

while in

(vlan)#

VLAN-specific

 

enter exit.

 

 

privileged

 

parameters.

 

 

 

 

 

 

EXEC mode.

 

 

 

 

 

 

 

 

 

 

 

Enter the

 

To exit to

 

 

 

interface

 

global

 

 

 

command

 

configuration

Use this mode to

Interface

 

(with a

 

mode, enter

 

switch

configure parameters

configuratio

 

specific

exit.

 

(config-if)#

for the switch and

n

 

interface)

To exist to

 

 

Ethernet ports.

 

 

while in global

 

privileged

 

 

 

 

 

 

configuration

 

EXEC mode,

 

 

 

mode

 

or end.

 

 

 

 

 

 

24-Hour Technical Support: 1-800-260-1312

International: 00-1-952-941-7600

 

 

 

17

 

 

Transition Networks MIL-SM2401MAF

 

Enter the ups

 

To exit to

 

 

command

 

Use this mode to UPS

 

 

privileged

UPS

while in

switch(ups)#

parameters for the

EXEC mode,

 

privileged

 

switch.

 

 

enter exit

 

EXEC mode.

 

 

 

 

 

 

 

 

 

 

 

 

Enter the PoE

 

To exit to

 

 

command

 

Use this mode to PoE

 

switch(PoE)

privileged

PoE

while in

parameters for the

#

EXEC mode,

 

privileged

switch.

 

 

enter exit

 

EXEC mode.

 

 

 

 

 

 

 

 

 

 

 

Commands Set List

System Commands Set

Commands

Command

Description

Defaults

Example

Level

 

 

 

 

 

 

 

 

 

system name

Global

Set switch system

 

Switch (config)#

configuration

 

system name

[word]

name string

 

mode

 

xxx

 

 

 

 

 

 

 

 

system

Global

Set switch system

 

Switch (config)#

location

configuration

 

system location

location string

 

[word]

mode

 

xxx

 

 

 

 

 

 

 

system

Global

Set switch system

 

Switch (config)#

description

configuration

 

system

description string

 

[word]

mode

 

description xxx

 

 

 

 

 

 

 

system

Global

Set switch system

 

Switch (config)#

configuration

 

system contact

contact [word]

contact window string

 

mode

 

xxx

 

 

 

 

 

 

 

 

24-Hour Technical Support: 1-800-260-1312

International: 00-1-952-941-7600

 

 

18

 

 

Transition Networks MIL-SM2401MAF

 

 

Use the ip address

 

 

 

 

interface configuration

 

Switch (config)#

ip address

 

command to set an IP

 

Global

 

ip address

[IP-address]

address for a switch.

 

configuration

 

192.168.1.1

[subnet-mask

Use the no form of this

 

mode

 

255.255.255.0

] [ gateway]

command to remove

 

 

 

192.168.1.254

 

 

an IP address or to

 

 

 

 

 

 

 

disable IP processing.

 

 

 

 

 

 

 

 

 

 

 

Switch# write

 

 

The “write memory” is

 

memeory

write

Privileged

save configuration

 

Update NVRAM

[memory|

and the “write

 

to Flash Complete

EXEC

 

terminal]

terminal” is show all

 

 

 

 

 

 

 

configuration.

 

Switch# write

 

 

 

 

terminal

 

 

 

 

 

 

Global

Halt and perform a

 

Switch (config)#

reload

configuration

 

cold restart

 

reload

 

mode

 

 

 

 

 

 

 

 

 

 

 

Global

 

 

Switch (config)#

default

configuration

Restore to default

 

 

default

 

mode

 

 

 

 

 

 

 

 

 

 

 

username

Global

Changes a login

 

Switch (config)#

configuration

username. (maximum

 

username

[word]

 

mode

10 words)

 

xxxxxx

 

 

 

 

 

 

 

password

Global

Specifies a password

 

Switch (config)#

configuration

 

password

[word]

(maximum 10 words)

 

mode

 

xxxxxx

 

 

 

 

 

 

 

 

24-Hour Technical Support: 1-800-260-1312

International: 00-1-952-941-7600

19

Transition Networks MIL-SM2401MAF

 

 

 

 

Switch# show

show

Privileged

Show username &

 

accounting

accounting

EXEC

password

 

Username: root

 

 

 

 

Password: root

 

 

 

 

 

 

 

 

 

Switch> show

 

 

 

 

system-info

 

 

 

 

Name: switch1

show

 

Show system

 

location: lab

User EXEC

 

Description:

system-info

information

 

 

 

layer2 switch

 

 

 

 

 

 

 

 

Contact:

 

 

 

 

somewhere

 

 

 

 

Serial NO: 1.00

 

 

 

 

 

 

 

 

 

Switch# show ip

 

 

 

 

address

 

 

 

 

ip: 192.168.1.1

show ip

Privileged

Show IP information

 

Address subnet:

EXEC

 

255.255.255.0

 

 

 

 

 

 

 

Address

 

 

 

 

gateway:

 

 

 

 

192.168.1.254

 

 

 

 

 

 

 

 

 

Switch> show

 

 

Use the show version

 

version

 

 

user EXEC command

 

Firmware

show version

User EXEC

to display version

 

version: 1.0

information for the

 

Hardware

 

 

 

 

 

hardware and

 

version: 3.0

 

 

firmware.

 

Kernel version:

 

 

 

 

1.10

 

 

 

 

 

24-Hour Technical Support: 1-800-260-1312

International: 00-1-952-941-7600

20

Transition Networks

MIL-SM2401MAF

Port Commands Set

Commands

Command

Description

Defaults

Example

Level

 

 

 

 

 

 

 

 

 

 

 

Use the fast Ethernet

 

Switch (config)#

interface

 

interface configuration

 

interface

 

 

 

 

[FastEthernet

Interface

command

 

fastEthernet 0/1

 

 

 

/module

configuration

 

 

 

Use the module

 

Switch (config)#

Ethernet] [slot

mode

 

 

 

 

id] [id]

 

Ethernet interface

 

interface

 

 

 

 

 

 

configuration

 

moduleEthernet

 

 

command

 

1/1

 

 

 

 

 

 

 

Use the duplex

 

Switch (config)#

 

 

configuration

 

 

 

 

interface

 

 

command to specify

 

 

 

Auto

fastEthernet 0/1

 

 

the duplex mode of

 

 

 

Switch (config-if)#

 

 

operation for Fast

 

 

 

 

duplex full

 

Interface

Ethernet.

 

duplex [full |

 

 

 

 

 

configuration

 

 

 

half| auto]

 

 

 

Use the duplex

 

Switch (config)#

mode

 

 

 

 

 

 

 

 

 

configuration

 

interface

 

 

command to specify

Auto

moduleEthernet

 

 

the duplex mode of

1/1

 

 

 

 

 

operation for module

 

Switch (config-if)#

 

 

Ethernet.

 

duplex full

 

 

 

 

 

 

 

Use the speed

 

Switch (config)#

 

 

configuration

 

 

Interface

 

interface

speed

command to specify

 

configuration

Auto

fastEthernet 0/1

[10 | 100 | auto]

the speed mode of

mode

 

Switch (config-if)#

 

operation for Fast

 

 

 

 

speed 10

 

 

Ethernet.

 

 

 

 

 

 

 

 

 

 

24-Hour Technical Support: 1-800-260-1312

International: 00-1-952-941-7600

 

 

21

 

 

Transition Networks

 

 

 

MIL-SM2401MAF

 

 

 

 

 

 

 

Use the speed

 

 

 

 

configuration

 

 

 

 

command to specify

 

 

 

 

the speed mode of

 

 

 

 

operation for module

 

Switch (config)#

 

 

Ethernet.

 

 

Interface

 

interface

speed [10| 100 |

The 100Base-FX

 

configuration

 

fastEthernet 1/2

1000 | auto]

module only

 

mode

 

Switch (config-if)#

 

supported for speed

 

 

 

 

speed 1000

 

 

100

 

 

 

 

 

 

 

The 1000Base-FX

 

 

 

 

module only

 

 

 

 

supported for speed

 

 

 

 

1000 & auto

 

 

 

 

 

 

 

 

 

Use the flow control

 

 

 

 

configuration

 

 

 

 

command on Ethernet

 

Switch (config)#

flowcontrol on

Interface

ports to control traffic

 

interface

or no

configuration

rates during

On

fastEthernet 0/1

flowcontrol

mode

congestion.

 

Switch (config-if)#

 

 

Use the no form of this

 

flowcontrol on

 

 

command to disable

 

 

 

 

security on the port.

 

 

 

 

 

 

 

 

 

Use the security

 

 

 

 

configuration

 

Switch (config)#

security on or

Interface

command on Ethernet

 

interface

configuration

ports.

Disable

fastEthernet 0/1

no security

mode

Use the no form of this

 

Switch (config-if)#

 

 

 

 

command to disable

 

security on

 

 

security on the port.

 

 

 

 

 

 

 

24-Hour Technical Support: 1-800-260-1312

International: 00-1-952-941-7600

 

 

22

 

 

Transition Networks MIL-SM2401MAF

 

 

Use the priority

 

 

 

 

configuration

 

Switch (config)#

priority on

Interface

command on Ethernet

 

interface

[high | low] or

configuration

ports.

Disable

fastEthernet 0/1

no priority

mode

Use the no form of this

 

Switch (config-if)#

 

 

command to disable

 

priority on high

 

 

security on the port.

 

 

 

 

 

 

 

 

 

Set bandwidth in or out

 

Switch (config)#

 

 

rate. The value rage is

 

 

Interface

 

interface

Bandwidth [in |

(0~999), and zero of

 

configuration

Disable

fastEthernet 0/1

out] [value]

the value is disable

mode

 

Switch (config-if)#

 

(The module can’t be

 

 

 

 

bandwidth in 50

 

 

setting)

 

 

 

 

 

 

 

 

 

 

 

 

Use the state interface

 

 

 

 

configuration

 

Switch (config)#

 

 

command to specify

 

 

Interface

 

interface

State [Enable |

the state mode of

 

configuration

Enable

fastEthernet 0/1

Disable]

operation for Ethernet

mode

 

Switch (config-if)#

 

ports. Use the disable

 

 

 

 

state disable

 

 

form of this command

 

 

 

 

 

 

 

to disable the port.

 

 

 

 

 

 

 

24-Hour Technical Support: 1-800-260-1312

International: 00-1-952-941-7600

23

Transition Networks MIL-SM2401MAF

 

 

 

 

Switch (config)#

 

Interface

 

 

interface

show interface

show interface

 

fastEthernet 0/1

configuration

 

configuration

configuration status

 

Switch (config-if)#

mode

 

 

 

 

show interface

 

 

 

 

 

 

 

 

configuration

 

 

 

 

 

 

 

 

 

Switch (config)#

 

Interface

 

 

interface

show interface

show interface actual

 

fastEthernet 0/1

configuration

 

status

status

 

Switch (config-if)#

mode

 

 

 

 

show interface

 

 

 

 

 

 

 

 

status

 

 

 

 

 

 

 

 

 

Switch (config)#

 

Interface

 

 

interface

show interface

show interface statistic

 

fastEthernet 0/1

configuration

 

accounting

counter

 

Switch (config-if)#

mode

 

 

 

 

show interface

 

 

 

 

 

 

 

 

accounting

 

 

 

 

 

 

 

 

 

Switch (config)#

show

Interface

Display the bandwidth

 

interface

configuration

 

fastEthernet 0/1

bandwidth

of the values

 

mode

 

Switch (config-if)#

 

 

 

 

 

 

 

show bandwidth

 

 

 

 

 

24-Hour Technical Support: 1-800-260-1312

International: 00-1-952-941-7600

24

Transition Networks MIL-SM2401MAF

interface

 

 

 

 

[FastEthernet

Interface

Use the fast Ethernet

 

Switch (config)#

/module

configuration

interface configuration

 

interface

Ethernet] [slot

mode

command

 

fastEthernet 0/1

id] [id]

 

 

 

 

 

 

 

 

 

Trunk Commands Set

Commands

Command

Description

Defaults

Example

Level

 

 

 

 

 

 

 

 

 

 

 

 

 

Switch # show

 

 

Display trunk group

 

group 1

show group

Privileged

information. If there

 

Group Trunk.1:

is no group-number

 

Ports: 02 03 04

[group-ID]

EXEC mode

 

in put, display all

 

Priority: 0001

 

 

 

 

 

trunk groups.

 

Lacp: Enable

 

 

 

 

Work ports: 0

 

 

 

 

 

port group

 

 

 

LACP:

[group-ID]

 

 

 

 

 

 

Switch (config)#

[port-list] lacp

 

Add trunking

 

 

 

port group 1 1-4

[on | off] workp

 

group.

 

Global

 

lacp on workp 2

[work ports]

Use the no form of

 

configuration

Disable

 

 

this command to

 

 

mode

 

Trunk without LACP:

no port group

delete trunking

 

 

 

Switch (config)#

[group-ID] lacp

 

group.

 

 

 

port group 1 1-4

[on | off] workp

 

 

 

 

 

 

lacp off workp 4

[work ports]

 

 

 

 

 

 

 

 

 

 

 

 

port group

 

 

 

Switch (config)#

Global

 

 

port group 3

[group-ID]

Set trunking group

 

configuration

 

activityport 2-4

activityport

port active

 

mode

 

 

[port ID]

 

 

 

 

 

 

Trunk.1 Lacp:

 

 

 

 

 

 

 

 

 

24-Hour Technical Support: 1-800-260-1312

International: 00-1-952-941-7600

 

 

25

 

 

Transition Networks

MIL-SM2401MAF

Enable

Check OK!

NEW: 2 4

Update finished!!

VLAN Commands Set

Commands

Command

Description

 

Defaults

Example

Level

 

 

 

 

 

 

 

 

 

 

 

 

 

Privileged

To enter the VLAN

 

 

Switch# vlan

Vlan datatbase

configuration

 

 

database

EXEC mode

 

 

 

interface

 

 

Switch(vlan)#

 

 

 

 

 

 

 

 

 

 

vlanmode

 

To set switch

 

 

 

VLAN

VLAN mode .Use

 

 

 

[disable|

 

 

Switch (vlan)#

database

the no form of this

 

Disable

portbase|

 

vlanmode 802.1q

mode

command to

 

 

802.1q | gvrp]

 

 

 

 

restore to default.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Port Base VLAN

 

 

 

 

 

 

 

 

vlan [Group

VLAN

 

 

 

 

Name] grpid

Add new Port Base

 

 

Switch (vlan)# vlan

database

 

 

[Group ID] port

VLAN

 

 

v2 grpid 2 port 1-4

mode

 

 

[Port ID]

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

no vlan [Group

VLAN

Delete port base

 

 

Switch (vlan)# no

Name] [Group

database

 

 

VLAN group

 

 

vlan v2 2

ID]

mode

 

 

 

 

 

 

 

 

 

 

 

 

show vlan

VLAN

Show VLAN of

 

 

 

[Group Name]

Group Name or

 

 

Switch (vlan)#

database

 

 

[Group ID] or

Group ID

 

 

Show vlan v2 2

mode

 

 

show vlan

information

 

 

 

 

 

 

 

 

 

 

 

 

 

24-Hour Technical Support: 1-800-260-1312

International: 00-1-952-941-7600

 

 

26

 

 

 

Transition Networks MIL-SM2401MAF

vlan [Group

VLAN

Set the port of

 

Switch (vlan)# vlan

name] add

database

 

some port group

 

v2 add 5

[port ID]

mode

 

 

 

 

 

 

 

 

 

vlan [Group

VLAN

Remove the port

 

Switch (vlan)# vlan

name] delete

database

 

from it’s port group.

 

v2 delete 5

[port ID]

mode

 

 

 

 

 

 

 

 

 

 

802.1Q | 802.1Q with GVRP VLAN mode

 

 

 

 

 

vlan [Group

 

Add new 802.1Q

 

 

 

VLAN

 

 

name]

 

 

 

VLAN

[group name]:

 

Switch(vlan)# vlan

vlanid [group

 

database

VLAN name

 

v2 vlanid 2 port 1-4

ID] port [port

 

mode

[group ID]: 2 ~ 4094

 

tag 2-4

ID] tag

 

 

[port ID]:

 

 

[port ID]

 

 

 

 

port members 1~9

 

 

 

 

 

 

 

 

 

 

 

vlan [group

 

 

 

Switch(vlan)# vlan

 

 

 

v2 add 5-8 tagged

name] add

VLAN

Set the port of

 

 

or

[port ID]

database

some port group

 

 

vlan v2 add 5-8

[tagged |

mode

tagged or untagged

 

 

untagged

untagged]

 

 

 

 

 

 

 

 

 

 

 

 

vlan [group

VLAN

Remove the port

 

Switch(vlan)# vlan

name] delete

database

 

from its port group.

 

v2 delete 5

[port ID]

mode

 

 

 

 

 

 

 

 

 

no vlan [Group

VLAN

 

 

Switch (vlan)# no

Delete 802.1Q

 

vlan v2

name] or

database

 

VLAN group

 

Switch (vlan)# no

[group ID]

mode

 

 

 

vlan v2 2

 

 

 

 

 

 

 

 

 

24-Hour Technical Support: 1-800-260-1312

International: 00-1-952-941-7600

 

 

27

 

 

Transition Networks

MIL-SM2401MAF

 

 

 

Add protocol vlan

 

[group name]: vlan

 

group name

 

IP-ip

 

ARP-arp

 

Appletalk-app

 

Appletalk_AARP-ap

 

p_arp

 

Novell_IPX-ipx

 

Switch(vlan)# vlan

 

Banyan_vines-bany

 

protocol v3 ip

 

an_c4

 

vlanid 2 port 5-8

 

Banyan_vines-bany

vlan protocol

tag 6,8

[group name]

an_c5

Banyan_vines-bany

 

[protocol

Switch(vlan)# vlan

VLAN

an_ad

value]

protocol v3 arp

database

Decent_mop_01-de

vlanid [group

vlanid 2 port 5-8

mode

cent_01

ID] port [port

tag 6,8

ID] tag [port

Decent_mop_02-de

cent_02

 

ID]

Switch(vlan)# vlan

 

Decent_dpr-decent

 

protocol v3 banyan

 

_dpr

 

vlanid 2 port 5-8

 

Decent_LAT-decen

 

tag 6,8

 

t_lat

 

Decent_LAVC-dece

 

nt_lavc

 

IBM SNA-ibm

 

X.75 internet-x75

 

X.25 Layer3-x25

[VLAN ID]: 2 ~ 4094 [port ID]:

port ID 1~10

24-Hour Technical Support: 1-800-260-1312

International: 00-1-952-941-7600

28

Transition Networks

 

 

 

MIL-SM2401MAF

 

 

 

 

 

 

 

Set VLAN ID range

 

 

 

 

[1~255] range 0

 

 

 

 

[256~511] range 1

 

 

 

 

[512~767] range 2

 

 

 

 

[768~1023] range 3

 

 

 

 

[1024~1279] range

 

 

 

 

4

 

 

 

 

[1280~1535] range

 

 

 

 

5

 

 

 

 

[1536~1791] range

 

 

 

 

6

 

 

 

 

[1792~2047] range

 

 

 

 

7

 

Switch (vlan)#

vlanidrange

VLAN

[2048~2303] range

 

vlanidrange 2

[VLAN ID

database

8

 

 

range]

mode

[2304~2559] range

 

OLD: 0

 

 

9

 

NEW: 2

 

 

[2560~2815] range

 

 

 

 

10

 

 

 

 

[2816~3071] range

 

 

 

 

11

 

 

 

 

[3072~3327] range

 

 

 

 

12

 

 

 

 

[3328~3583] range

 

 

 

 

13

 

 

 

 

[3584~3839] range

 

 

 

 

14

 

 

 

 

[3840~4094] range

 

 

 

 

15

 

 

 

 

 

 

 

VLAN protocol

VLAN

Set the port of

 

Switch (vlan)# vlan

[Group name]

 

database

some port group

 

protocol v2 add 5

add [port ID]

 

mode

tagged or untagged

 

tagged

[tagged |

 

 

 

 

 

 

 

 

 

 

24-Hour Technical Support: 1-800-260-1312

International: 00-1-952-941-7600

 

 

29

 

 

Transition Networks

 

 

 

MIL-SM2401MAF

 

 

 

 

 

untagged]

 

 

 

 

 

 

 

 

 

VLAN protocol

VLAN

Remove the port

 

Switch (vlan)# vlan

[Group name]

database

 

protocol v2 delete

from its port group.

 

delete [port ID]

mode

 

5

 

 

 

 

 

 

 

show vlan

 

Show VLAN of

 

 

VLAN

Group Name or

 

 

[Group name]

 

Switch (vlan)# show

database

VLAN ID

 

[Group ID] or

 

vlan v2 2

mode

information

 

show vlan

 

 

 

vlanid: 1 ~ 4094

 

 

 

 

 

 

 

 

 

 

 

 

 

show protocol vlan

 

 

show vlan

VLAN

Protocol

 

Switch (vlan)# show

database

ip

 

protocol

 

vlan protocol

mode

ipx

 

 

 

 

 

 

netbios

 

 

 

 

 

 

 

port [port ID]

 

 

 

 

pvid [port VID]

VLAN

Set Port PVID and

 

Switch (vlan)# port

ingressfilter1

Ingress Filter

 

2 pvid 2

database

 

[on | off]

Rules1 & Ingress

 

ingressfilter1 off

mode

 

ingressfilter2

Filter Rules2

 

ingressfilter2 on

 

 

[on | off]

 

 

 

 

 

 

 

 

 

 

 

 

 

Switch (vlan)# show

 

 

 

 

port 2

 

VLAN

show Port PVID

 

Port ID: 2

show port [port

and Ingress Filter

 

Port Vid: 2

database

 

ID]

Rules1 & Ingress

 

Ingress 1 Filter:

mode

 

 

Filter Rules2

 

Disable

 

 

 

 

 

 

 

Ingress 2 Filter:

 

 

 

 

Enable

 

 

 

 

 

24-Hour Technical Support: 1-800-260-1312

International: 00-1-952-941-7600

 

 

30

 

 

Transition Networks

MIL-SM2401MAF

Spanning Tree Commands Set

Commands

Command

Description

Defaults

Example

Level

 

 

 

 

 

 

 

 

 

 

 

 

 

Switch> show

 

 

 

 

spanning-tree

 

 

 

 

System:

 

 

 

 

Priority: 32768

 

 

 

 

Max Age: 20

 

 

 

 

Hello Time: 2

 

 

Display a summary

 

Forward Delay: 15

show

User EXEC

 

Priority: 32768

of the spanning-tree

 

spanning-tree

mode

 

Mac Address:

states.

 

 

 

 

004063800030

 

 

 

 

 

 

 

 

Root_Path_Cost: 0

 

 

 

 

Root Port: we are

 

 

 

 

root

 

 

 

 

Max Age: 20

 

 

 

 

Hello Time: 2

 

 

 

 

Forward Delay: 15

 

 

 

 

 

 

 

Use the

 

 

 

 

spanning-tree

 

Switch (config)#

spanning-tree

 

global configuration

 

 

 

spanning-tree on

[on / off]

Global

command to enable

 

 

 

 

configuration

Spanning Tree

Disable

 

or

mode

Protocol (STP). Use

 

or

 

Switch (config)# no

no spanning-tree

 

the no form of the

 

 

 

spanning-tree

 

 

command to restore

 

 

 

 

 

 

 

to default

 

 

 

 

 

 

 

24-Hour Technical Support: 1-800-260-1312

International: 00-1-952-941-7600

31

Transition Networks MIL-SM2401MAF

 

 

 

Use the

 

 

 

 

 

spanning-tree

 

 

 

 

 

max-age global

 

 

 

 

 

configuration

 

 

spanning-tree

Global

 

command to

 

Switch (config)#

configuration

 

change the priority.

32768

spanning-tree

priority [number]

 

mode

 

 

 

priority 32767

 

 

 

 

 

 

 

Use the no form of

 

 

 

 

 

this command to

 

 

 

 

 

return to the default

 

 

 

 

 

interval.

 

 

 

 

 

 

 

 

 

 

 

Use the

 

 

 

 

 

spanning-tree

 

 

 

 

 

max-age global

 

 

 

 

 

configuration

 

 

 

 

 

command to

 

 

 

 

 

change the interval

 

 

 

 

 

between messages

 

 

 

 

 

the spanning tree

 

 

 

 

 

receives from the

 

 

spanning-tree

Global

 

root switch. If a

 

Switch (config)#

max-age

configuration

 

switch does not

20 sec

spanning-tree

[seconds]

mode

 

receive a bridge

 

max-age 15

 

 

 

protocol

 

 

 

 

 

data unit (BPDU)

 

 

 

 

 

message from the

 

 

 

 

 

root switch within

 

 

 

 

 

this interval, it

 

 

 

 

 

recomputes the

 

 

 

 

 

Spanning Tree

 

 

 

 

 

Protocol (STP)

 

 

 

 

 

topology. Use the

 

 

 

 

 

 

 

 

24-Hour Technical Support: 1-800-260-1312

 

International: 00-1-952-941-7600

 

 

 

32

 

 

Transition Networks

 

 

 

 

MIL-SM2401MAF

 

 

 

 

 

 

 

 

 

no form of this

 

 

 

 

 

command to return

 

 

 

 

 

to the default

 

 

 

 

 

interval.

 

 

 

 

 

 

 

 

 

 

 

Use the

 

 

 

 

 

spanning-tree

 

 

 

 

 

hello-time global

 

 

 

 

 

configuration

 

 

 

 

 

command to specify

 

 

spanning-tree

Global

 

the interval

 

Switch (config)#

hello-time

configuration

 

between hello

2 sec.

spanning-tree

[seconds]

mode

 

bridge protocol data

 

hello-time 3

 

 

 

units (BPDUs). Use

 

 

 

 

 

the no form of this

 

 

 

 

 

command to return

 

 

 

 

 

to the default

 

 

 

 

 

interval.

 

 

 

 

 

 

 

 

 

 

 

Use the

 

 

 

 

 

spanning-tree cost

 

 

 

 

 

interface

 

 

 

 

 

configuration

 

 

 

 

 

command to set the

 

 

 

 

 

path cost for

10 Mbps

Switch (config)#

stp-path-cost

Interface

 

Spanning Tree

– 100

interface

configuration

 

Protocol (STP)

 

fastEthernet 0/2

[number]

 

 

mode

 

calculations. In the

100 Mbps

Switch (config-if)#

 

 

 

 

 

event of a loop,

– 10

stp-path-cost 20

 

 

 

spanning tree

 

 

 

 

 

considers the path

 

 

 

 

 

cost when selecting

 

 

 

 

 

an interface to

 

 

 

 

 

place into the

 

 

 

 

 

 

 

 

24-Hour Technical Support: 1-800-260-1312

 

International: 00-1-952-941-7600

 

 

 

33

 

 

Transition Networks

 

 

 

 

MIL-SM2401MAF

 

 

 

 

 

 

 

 

 

forwarding state.

 

 

 

 

 

Use the no form of

 

 

 

 

 

this command to

 

 

 

 

 

return to the default

 

 

 

 

 

value.

 

 

 

 

 

 

 

 

 

 

 

Use the

 

 

 

 

 

spanning-tree

 

 

 

 

 

forward-time global

 

 

 

 

 

configuration

 

 

 

 

 

command to set the

 

 

 

 

 

forwarding-time for

 

 

 

 

 

the specified

 

 

 

 

 

spanning-tree

 

 

spanning-tree

Global

 

instances. The

 

Switch (config)#

 

forwarding time

 

forward-time

configuration

 

15 sec.

spanning-tree

 

determines how

[seconds]

mode

 

 

forward-time 20

 

long each of the

 

 

 

 

 

 

 

 

 

listening and

 

 

 

 

 

learning states last

 

 

 

 

 

before the port

 

 

 

 

 

begins forwarding.

 

 

 

 

 

Use the no form of

 

 

 

 

 

this command to

 

 

 

 

 

return to the default

 

 

 

 

 

value.

 

 

 

 

 

 

 

 

 

 

 

Use the

 

Switch (config)#

 

 

 

spanning-tree

 

 

 

 

 

interface

 

Interface

 

port-priority

 

stp-path-priority

 

 

fastEthernet 0/2

configuration

 

interface

128

[number]

 

Switch (config-if)#

mode

 

configuration

 

 

 

 

stp-path-priority

 

 

 

command to

 

 

 

 

 

127

 

 

 

configure a port

 

 

 

 

 

 

 

 

 

 

 

 

24-Hour Technical Support: 1-800-260-1312

 

International: 00-1-952-941-7600

 

 

 

34

 

 

Transition Networks

MIL-SM2401MAF

priority that is used when two switches tie for position as the root switch. Use the no form of this command to return to the default value.

QOS Commands Set

Commands

Command

Description

Defaults

Example

Level

 

 

 

 

 

 

 

 

 

qos

 

Enable/Disable

 

 

storm-control

Global

broadcast storm

 

Switch (config)#

[5|10|15|20|25|

configuration

control. Use the no

OFF

qos storm-control

off (%)] or no

mode

form of this command

 

5

storm-control

 

to restore to default.

 

 

 

 

 

 

 

qos

 

 

 

 

low-priority-del

 

Enable/Disable low

 

Switch (config)#

ay-bound

Global

priority delay board.

 

 

qos

[on|off] [sec.]

configuration

Use the no form of

OFF

low-priority-delay

or no qos

mode

this command to

 

 

-bound on 1

low-priority-del

 

restore to default.

 

 

 

 

ay-bound

 

 

 

 

 

 

 

 

 

qos level

Global

 

0~3 LOW

Switch (config)#

configuration

[Priority] 0~7

[priority]

4~7 HI

qos level 2,3

mode

 

 

 

 

 

 

 

 

 

 

no qos level

Global

 

0~3 LOW

Switch (config)# no

configuration

[Priority] 0~7

[priority]

4~7 HI

qos level 0-7

mode

 

 

 

 

 

 

 

 

 

 

24-Hour Technical Support: 1-800-260-1312

International: 00-1-952-941-7600

35

Transition Networks

 

 

 

MIL-SM2401MAF

 

 

 

 

 

 

 

 

 

WRR:

 

 

 

 

Switch (config)#

 

 

 

 

qos queuepolicy

 

 

 

 

wrr hi 7 low 1

 

 

[Policy]:fcfs: first in

 

 

qos

 

and first out

 

First Come First

 

wrr: weight round

 

Served:

queuepolicy

Global

WRR

robin

Switch (config)#

[Policy] hi

configuration

Hi 2

ahbl: all high before

qos queuepolicy

[number] low

mode

Low 1

low.

fcfs

[number]

 

 

 

[Priority] Hi:1~7

 

 

 

 

 

 

 

 

Low:1

 

All High before

 

 

 

 

Low:

 

 

 

 

Switch (config)#

 

 

 

 

qos queuepolicy

 

 

 

 

ahbl

 

 

 

 

 

qos

 

Set qos bridge delay

 

 

bridge-delay-b

 

 

Switch (config)#

Global

bound

 

ound [sec.]

 

qos

configuration

Use the no form of

OFF

no qos

bridge-delay-bou

mode

this command to

 

bridge-delay-b

 

nd 1

 

restore to default.

 

ound

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Switch (config)#

show qos

Global

Show broadcast

 

show qos

configuration

 

storm-control

storm-control

storm control.

 

mode

 

QOS storm control

 

 

 

 

 

 

 

mode: ENABLE

 

 

 

 

 

show qos

Global

 

 

Switch (config)#

configuration

Show qos policy

 

show qos policy

policy

 

mode

 

 

Qos Mode: WRR

 

 

 

 

 

 

 

 

24-Hour Technical Support: 1-800-260-1312

International: 00-1-952-941-7600

 

 

36

 

 

Transition Networks MIL-SM2401MAF

 

 

 

 

Switch (config)#

show qos

Global

 

 

show qos

Show low priority

 

low-priority-delay

low-priority-del

configuration

 

delay board.

 

-bound

ay-bound

mode

 

 

 

Qos low priority

 

 

 

 

 

 

 

 

delay bound: 1

 

 

 

 

 

 

 

 

 

Switch (config)#

show qos

Global

 

 

show qos

Show bridge delay

 

bridge-delay-bou

bridge-delay-b

configuration

 

bound

 

nd

ound

mode

 

 

 

bridge-delay-bound

 

 

 

 

 

 

 

 

5

 

 

 

 

 

IGMP Commands Set

Commands

Command

Description

Defaults

Example

Level

 

 

 

 

 

 

 

 

 

 

Global

Enable /Disable

 

Switch (config)#

igmp [on | off]

configuration

IGMP snooping

Off

igmp on

 

mode

function

 

 

 

 

 

 

 

 

 

igmp-query

Global

Modify IGMP query

 

Switch (config)#

[auto |enable |

configuration

Disable

mode

igmp-query enable

disable]

mode

 

 

 

 

 

 

 

 

 

 

 

 

 

Switch# show ip

show ip igmp

Privileged

Displays the details of

 

igmp profile

 

IP

profile

EXEC mode

an IGMP profile entry.

 

 

VID Port 224.1.1.1

 

 

 

 

 

 

 

 

10 1,2,6

 

 

 

 

 

24-Hour Technical Support: 1-800-260-1312

International: 00-1-952-941-7600

37

Transition Networks

MIL-SM2401MAF

Mac / Filter Table Commands Set

Commands

Command

Description

Defaults

Example

Level

 

 

 

 

 

 

 

 

 

 

 

Use the

 

Switch (config)#

 

 

mac-address-table

 

 

 

 

mac-address-table

 

 

aging-time global

 

 

 

 

aging-time on

 

 

configuration

 

mac-address-ta

 

 

 

 

command to set the

 

 

ble aging-time

 

 

Switch (config)#

 

length of time that a

 

[on | off]

 

 

mac-address-table

 

dynamic entry

 

 

 

 

aging-time 333

 

Global

remains in the MAC

 

mac-address-ta

 

 

configuration

address table after

300 secs

 

ble aging-time

(Disable)

mode

the entry is used or

 

[sec.]

 

Switch (config)#

 

updated.

 

or no

 

 

mac-address-table

 

Use the no form of

 

mac-address-ta

 

 

aging-time off

 

this command to use

 

ble aging-time

 

 

Or

 

the default

 

 

 

 

Switch(config)# no

 

 

aging-time interval.

 

 

 

 

mac-address-table

 

 

The aging time

 

 

 

 

aging-time

 

 

applies to all VLANs.

 

 

 

 

 

 

 

 

 

 

 

 

Use the

 

 

 

 

mac-address-table

 

Switch (config)#

mac-address-ta

 

static to add static |

 

interface

ble table [static

Interface

filter addresses to the

 

fastEthernet 0/2

| filter] hwaddr

MAC address table.

 

Switch (config-if)#

configuration

N/A

[MAC address]

Use the no form of

mac-address-table

mode

 

vlanid

this command to

 

static hwaddr

 

 

[VLAN-ID]

 

remove static entries

 

004063112233

 

 

from the MAC

 

vlanid 10

 

 

address table.

 

 

 

 

 

 

 

24-Hour Technical Support: 1-800-260-1312

International: 00-1-952-941-7600

38

Transition Networks MIL-SM2401MAF

 

 

 

 

Switch (config)#

no

 

Use the no

 

interface

mac-address-ta

 

 

fastEthernet 0/2

 

mac-address-table

 

ble [static |

Interface

 

Switch (config-if)#

privileged EXEC

 

filter] hwaddr

configuration

 

no

command to delete

 

[MAC address]

mode

 

mac-address-table

entries from the MAC

 

vlanid

 

 

static hwaddr

 

address table.

 

[VLAN-ID]

 

 

004063112233

 

 

 

 

 

 

 

vlanid 10

 

 

 

 

 

 

 

Use the show

 

 

show

 

mac-address-table

 

Switch # show

mac-address-ta

Privileged

user EXEC

 

 

mac-address-table

ble [static |

EXEC mode

command to display

 

 

static

filter]

 

the MAC address

 

 

 

 

 

 

table.

 

 

 

 

 

 

 

 

 

Use the show

 

Switch# show

show

 

mac-address-table

 

 

 

mac-address-table

mac-address-ta

Privileged

user EXEC

 

 

aging-time

ble

EXEC mode

command to display

 

 

MAC Address

aging-time

 

the MAC address

 

 

 

aging-time: 300

 

 

table.

 

 

 

 

 

 

 

 

 

 

24-Hour Technical Support: 1-800-260-1312

International: 00-1-952-941-7600

39

Transition Networks

MIL-SM2401MAF

SNMP Commands Set

Commands

Command

 

Description

Defaults

Example

Level

 

 

 

 

 

 

 

 

 

 

 

 

snmp

Global

 

Set SNMP agent

 

Switch (config)#

system-name

configuration

 

N/A

snmp system-name

 

system name

[word]

mode

 

 

l2switch

 

 

 

 

 

 

 

 

 

snmp

Global

 

Set SNMP agent

 

Switch (config)#

system-location

configuration

 

N/A

snmp

 

system location

[word]

mode

 

 

system-location lab

 

 

 

 

 

 

 

 

 

snmp

Global

 

 

 

Switch (config)#

 

Set SNMP agent

 

snmp

system-contact

configuration

 

N/A

 

system contact

system-contact

[word]

mode

 

 

 

 

 

where

 

 

 

 

 

 

 

 

 

 

 

snmp

 

 

 

 

Switch (config)#

 

 

Add SNMP

 

snmp

community-strin

 

 

 

 

 

community string.

 

community-strings

gs [word] right

 

 

 

Global

 

Use the no form of

 

public right RW

[RO | RW]

 

PUBLIC

configuration

 

this command to

 

Or

 

RO

 

mode

 

remove the

Switch(config)#

no snmp

 

 

 

 

specified

 

no snmp

community-strin

 

 

 

 

 

community.

 

community-strings

gs [word]

 

 

 

 

 

 

 

public right rw

 

 

 

 

 

 

 

 

 

 

 

snmp-server

 

 

 

 

Switch(config)#

host

 

 

Configure SNMP

 

snmp-server host

[IP-address]

Global

 

 

192.168.1.50

 

server host

 

community

configuration

 

N/A

community

 

information and

[word]

mode

 

 

public

 

community string

 

 

 

 

 

 

No snmp-server

 

 

 

 

Switch(config)# no

 

 

 

 

 

 

24-Hour Technical Support: 1-800-260-1312

 

International: 00-1-952-941-7600

 

 

 

40

 

 

Transition Networks

 

 

 

MIL-SM2401MAF

 

 

 

 

 

host [IP

 

 

 

snmp-server host

address]

 

 

 

192.168.1.50

community

 

 

 

community public

[word]

 

 

 

 

 

 

 

 

 

snmp

Global

Set SNMP agent

 

Switch (config)#

system-name

configuration

N/A

snmp system-name

system name

[word]

mode

 

l2switch

 

 

 

 

 

 

 

Port Mirroring Commands Set

Commands

Command

Description

Defaults

Example

Level

 

 

 

 

 

 

 

 

 

 

 

Use the port

 

 

 

 

monitor interface

 

 

 

 

configuration

 

 

 

 

command to

 

 

port monitor

 

enable Switch

 

Switch (config)#

[RX|TX|both]

Interface

Port Analyzer

 

Interface fastEthernet

[port ID]

configuration

(SPAN) port

N/A

0/8

Or

mode

monitoring on a

 

Switch (config-if)# port

no port monitor

 

port. Use the no

 

monitor both 3

 

 

form of this

 

 

 

 

command to

 

 

 

 

return the port to

 

 

 

 

its default value.

 

 

 

 

 

 

 

 

 

Use the show port

 

Switch # show port

 

 

monitor privileged

 

monitor

show port

Privileged

EXEC command

 

State: Enable

to display the

 

AnalysisPortId: 8

monitor

EXEC mode

 

ports for which

 

Port 01 TxRx: Monitor

 

 

 

 

 

Switched Port

 

Port 02 TxRx:

 

 

Analyzer (SPAN)

 

Port 03 TxRx:

 

 

 

 

 

24-Hour Technical Support: 1-800-260-1312

International: 00-1-952-941-7600

 

 

41

 

 

Transition Networks

 

MIL-SM2401MAF

 

 

 

 

 

 

 

port monitoring is

 

Port 04 TxRx:

 

 

enabled.

 

Port 05 TxRx:

 

 

 

 

Port 06 TxRx:

 

 

 

 

Port 07 TxRx:

 

 

 

 

Port 08 TxRx: Analysis

 

 

 

 

Port 09 TxRx:

 

 

 

 

Port 10 TxRx:

 

 

 

 

OK.

 

 

 

 

 

802.1x Commands Set

Commands

Command

Description

Defaults

Example

Level

 

 

 

 

 

 

 

 

 

 

User EXEC

Display a summary of

 

Switch> show

show 8021x

the 802.1x properties

N/A

mode

 

 

and also the port sates.

 

8021x

 

 

 

 

 

 

 

 

 

 

 

Use the 802.1x global

 

 

8021x [on | off]

Global

configuration command

 

 

to enable 802.1x

 

Switch (config)#

or

configuration

Disable

protocols. Use the no

 

No 8021x

mode

 

8021x on

form of the command to

 

 

 

 

 

 

 

 

restore to default

 

 

 

 

 

 

 

 

 

Use the 802.1x system

 

Switch (config)#

8021x system

 

radius IP global

 

8021x system

radiusip

 

configuration command

 

radiusip

[IP address]

Global

to change the radius

 

192.168.1.1

Or

configuration

server IP.

192.16

 

8.16.3

 

no 8021x

mode

 

(Default)

 

 

system

 

Use the no form of this

 

Switch(config)#

radiusip

 

command to return to

 

no 8021x system

 

 

the default interval.

 

radiousip

 

 

 

 

 

24-Hour Technical Support: 1-800-260-1312

International: 00-1-952-941-7600

 

 

42

 

 

Transition Networks MIL-SM2401MAF

 

 

Use the 802.1x system

 

Switch (config)#

8021x system

 

sharekey global

 

 

 

8021x system

sharekey

 

configuration command

 

 

 

sharekey 123456

[number]

Global

to change the shared

 

 

 

Or

configuration

key value.

123456

(Default)

no 8021x

mode

 

78

 

Switch (config)#

system

 

Use the no form of this

 

 

 

no 8021x system

sharekey

 

command to return to

 

 

 

sharekey

 

 

the default interval.

 

 

 

 

 

 

 

 

 

 

8021x system

Global

 

 

Switch (config)#

serverport

configuration

set radius server port

1812

8021x system

[Port Number]

mode

 

 

serverport 1815

 

 

 

 

 

8021x system

Global

 

 

Switch (config)#

accountport

configuration

set accounting port

1813

8021x system

[Port Number]

mode

 

 

accountport 1816

 

 

 

 

 

 

Global

 

NAS_L

Switch (config)#

8021x system

 

2_

configuration

set NAS ID

8021x system

nasid [word]

SWITC

mode

 

nasid test1

 

 

H

 

 

 

 

 

 

 

 

 

 

 

Use the 802.1x misc

 

 

 

 

quiet period global

 

Switch (config)#

8021x misc

 

configuration command

 

8021x misc

quietperiod

Global

to specify the quiet

 

quietperiod 10

[sec.]

period value of the

 

 

configuration

60 sec.

 

Or

switch.

(Default)

mode

 

no 8021x misc

 

 

Switch(config)#

 

 

 

quietperiod

 

Use the no form of this

 

no 8021x misc

 

 

command to return to

 

quietperiod

 

 

the default interval.

 

 

 

 

 

 

 

24-Hour Technical Support: 1-800-260-1312

International: 00-1-952-941-7600

43

Transition Networks MIL-SM2401MAF

 

 

Use the 802.1x misc TX

 

Switch (config)#

8021x misc

 

period global

 

8021x misc

 

configuration command

 

txperiod 5

txperiod [sec.]

Global

 

to set the TX period.

 

 

Or

configuration

30 sec.

 

 

(Default)

no 8021x

mode

 

 

Use the no form of this

 

Switch(config)# no

txperiod

 

 

 

command to return to

 

8021x misc

 

 

 

 

 

the default value.

 

txperiod

 

 

 

 

 

8021x misc

Global

Set the period of time

 

Switch (config)#

the switch wait for a

 

supptimeout

configuration

30 sec.

8021x misc

supplicant response to

[sec.]

mode

 

supptimeout 30

an EAP request.

 

 

 

 

 

 

 

 

 

 

8021x misc

Global

Set the period of time

 

Switch (config)#

the switch waits for a

 

servertimeout

configuration

30 sec.

8021x misc

server response to an

[sec.]

mode

 

servertimeout 50

authentication request.

 

 

 

 

 

 

 

 

 

 

 

 

Set the number of

 

 

8021x misc

Global

authentication that must

 

Switch (config)#

time-out before

 

maxrequest

configuration

2

8021x misc

authentication fails and

[Number]

mode

 

maxrequest 2

the authentication

 

 

 

 

 

 

 

session ends.

 

 

 

 

 

 

 

8021x misc

Global

Set the period of time

 

Switch(config)#

after which clients

 

reauthperiod

configuration

3600

8021x misc

connected must be

[sec.]

mode

 

reauthperiod 20

re-authenticated.

 

 

 

 

 

 

 

 

 

 

8021x prostate

 

Use the 802.1x port

 

Switch (config)#

Interface

state interface

 

interface

[reject | accept

 

configuration

configuration command

N/A

fastethernet 0/3

| authorize |

mode

to set the state of the

 

Switch (config-if)#

disable]

 

 

selected port.

 

8021x portstate

 

 

 

 

 

 

 

 

24-Hour Technical Support: 1-800-260-1312

International: 00-1-952-941-7600

 

 

44

 

 

Transition Networks

 

MIL-SM2401MAF

 

 

 

 

 

 

 

Reject: the specified

 

accept

 

 

port is required to be

 

 

 

 

held in the

 

 

 

 

unauthorized state.

 

 

 

 

Accept: the specified

 

 

 

 

port is required to be

 

 

 

 

held in the Authorized

 

 

 

 

state.

 

 

 

 

Authorized: the

 

 

 

 

specified port is set to

 

 

 

 

the Authorized or

 

 

 

 

Unauthorized state in

 

 

 

 

accordance with the

 

 

 

 

outcome of an

 

 

 

 

authentication

 

 

 

 

exchange between

 

 

 

 

the Supplicant and the

 

 

 

 

authentication server.

 

 

 

 

Disable: The

 

 

 

 

specified port is

 

 

 

 

required to be held in

 

 

 

 

the Authorized state.

 

 

 

 

 

 

 

TFTP Commands Set

Commands

Command

Description

Defaults

Example

Level

 

 

 

 

 

 

 

 

 

copy

 

 

 

Switch (config)#

flash:config.te

Global

 

 

copy

xt tftp [TFTP IP

configuration

Backup configure file

 

flash:config.text

 

 

address] [file

mode

command

 

tftp

 

 

name]

 

 

 

Server

 

 

 

 

 

24-Hour Technical Support: 1-800-260-1312

International: 00-1-952-941-7600

 

45

 

 

Transition Networks

 

 

 

MIL-SM2401MAF

 

 

 

 

 

 

 

 

 

 

 

IP:192.168.1.1

 

 

 

 

 

Image

 

 

 

 

 

Filename:backup.

 

 

 

 

 

dat

 

 

 

 

 

 

 

 

 

 

 

Switch(config)#

tftp:config.text

 

 

 

 

Tftp:config.text

 

 

 

 

flash

flash

 

Global

 

 

 

Restore configure file

 

Server

[TFTP IP

 

configuration

 

 

command

 

IP:192.168.1.1

address] [file

 

mode

 

 

 

 

Image

name]

 

 

 

 

 

 

 

 

Filename:restore.

 

 

 

 

 

 

 

 

 

 

dat

 

 

 

 

 

 

 

 

 

 

 

Switch (config)#

tftp:firmware

 

 

 

 

Tftp:firmware

 

 

 

 

flash

flash

 

Global

 

 

 

Update firmware

 

Server

[TFTP IP

 

configuration

 

 

command

 

IP:192.168.1.1

address]

 

mode

 

 

 

 

Image

[file name]

 

 

 

 

 

 

 

 

Filename:image.bi

 

 

 

 

 

 

 

 

 

 

n

 

 

 

 

 

 

UPS Commands Set

Commands

Command

Description

Defaults

Example

Level

 

 

 

 

 

 

 

 

 

 

 

 

 

Switch

status

UPS mode

Display a summary of

 

(ups)#status

 

 

Input Output

 

 

the UPS status.

 

 

 

 

 

Voltage…….

 

 

 

 

 

24-Hour Technical Support: 1-800-260-1312

International: 00-1-952-941-7600

46

Transition Networks

 

 

 

MIL-SM2401MAF

 

 

 

 

 

 

 

 

 

 

 

Switch (ups)#

 

 

 

 

 

info

Info

 

UPS mode

Show UPS information

 

Company

 

 

Name :xxx

 

 

 

 

 

 

 

 

 

 

Model :xxx

 

 

 

 

 

Version :xxx

 

 

 

 

 

 

 

 

 

UPS will perform the

 

Switch (ups)#

Test 10

 

UPS mode

self-test for 10

 

test10

 

 

 

seconds.

 

test OK

 

 

 

 

 

 

PoE Commands Set

Commands

Command

Description

Defaults

Example

Level

 

 

 

 

 

 

 

 

 

status

PoE mode

Show PoE information

 

Switch(PoE)#

 

status

 

 

 

 

 

 

 

 

 

 

 

 

 

Switch(PoE)#

setpm [on |

 

Enabling or disabling

 

setpm on

PoE mode

the power

 

Set Power

off]

 

 

management.

 

Management

 

 

 

 

 

 

 

Enable

 

 

 

 

 

 

 

Enabling or disabling

 

 

 

 

total power output limit.

 

 

setlimit

 

When is enabling, the

 

Switch(PoE)#

PoE mode

total power output limit

 

[value]

 

setlimit 100

 

will follow the value

 

 

 

 

 

 

 

that set in power limit

 

 

 

 

max.

 

 

 

 

 

 

 

24-Hour Technical Support: 1-800-260-1312

International: 00-1-952-941-7600

47

Transition Networks MIL-SM2401MAF

portebl

 

Enabling or disabling

 

Switch(PoE)#

[enable |

 

 

PoE mode

the port PoE injected

 

portebl disable

disable]

 

 

function.

 

1-3

[ports]

 

 

 

 

 

 

 

 

 

 

 

portcls

 

Enabling or disabling

 

Switch(PoE)#

[enable |

 

 

PoE mode

per port power limit by

 

portcls enable

disable]

 

 

classification.

 

1-3

[ports]

 

 

 

 

 

 

 

 

 

 

 

portmng

 

Enabling or disabling

 

Switch(PoE)#

[enable |

 

 

PoE mode

per port power limit by

 

portmng enable

disable]

 

 

management.

 

2-5

[ports]

 

 

 

 

 

 

 

 

 

 

 

portleg

 

Enabling or disabling

 

Switch(PoE)#

[enable |

 

 

PoE mode

per port legacy

 

portleg enable

disable]

 

 

detection.

 

3-6

[ports]

 

 

 

 

 

 

 

 

 

 

 

portpri

 

Set port priority for the

 

Switch(PoE)#

[critical | high

PoE mode

power supply

 

 

portpri critical 2

| low] [ports]

 

management.

 

 

 

 

 

 

 

 

 

portplm

 

Set per port power limit

 

Switch(PoE)#

PoE mode

 

portplm 12200

[value] [ports]

Max.

 

 

 

5-7

 

 

 

 

 

 

 

 

 

System log Commands Set

Commands

Command

Description

Defaults

Example

Level

 

 

 

 

 

 

 

 

 

show

User EXEC

Display system log.

 

Switch>

systemlog

 

show systemlog

 

 

 

 

 

 

 

 

24-Hour Technical Support: 1-800-260-1312

International: 00-1-952-941-7600

 

 

48

 

 

Transition Networks

 

 

 

MIL-SM2401MAF

 

 

 

 

 

 

 

 

 

 

 

switch# show

 

 

 

 

 

systemlog

show

 

Privileged

Show system log client

 

Syslog Client:

 

 

Enable

systemlog

 

EXEC

& server information

 

 

 

Syslog Server Ip:

 

 

 

 

 

 

 

 

 

 

192.168.16.2

 

 

 

 

 

 

systemlog ip

 

Global

Set System log server

 

Switch(config)#

 

configuration

 

systemlog ip

[IP address]

 

IP address.

 

 

mode

 

192.168.1.100

 

 

 

 

 

 

 

 

 

 

systemlog

 

Global

Enable or disable

 

Switch(config)#

[enable |

 

configuration

 

systemlog

 

system log mode

 

disable]

 

mode

 

enable

 

 

 

 

 

 

 

 

 

SNTP Commands Set

Commands

Command

Description

Defaults

Example

Level

 

 

 

 

 

 

 

 

 

 

 

 

 

Switch(config)#

sntp [enable |

Global

 

 

sntp enable

configuration

Enable/Disable SNTP.

Disable

 

disable]

 

mode

 

 

Switch(config)#

 

 

 

 

 

 

 

sntp disable

 

 

 

 

 

sntp ip [IP

Global

Set SNTP server IP

 

switch#sntp ip

configuration

 

address]

address.

 

192.168.16.123

mode

 

 

 

 

 

 

 

 

 

 

sntp

Global

 

 

Switch(config)#

timezone

configuration

Set time zone.

 

 

sntp timezone 8

[value]

mode

 

 

 

 

 

 

 

 

 

 

24-Hour Technical Support: 1-800-260-1312

International: 00-1-952-941-7600

49

Transition Networks

MIL-SM2401MAF

Web-Based Management

This section introduces the configuration and functions of the Web-Based management.

About Web-based Management

On the CPU board of the switch there is an embedded HTML web site residing in flash memory, which offers advanced management features and allow users to manage the switch from anywhere on the network through a standard browser such as Microsoft Internet Explorer.

The Web-Based Management supports Internet Explorer 6.0. And, it is applied with Java Applets for reducing network bandwidth consumption, enhance access speed and present an easy viewing screen.

Preparing for Web Management

Before starting web management, user can use console to log in the switch for checking the default IP of the switch. Please refer to Console Management Chapter for console login. If user needs change IP address in first time, please use console mode to modify it. The default value is shown as below:

IP Address: 192.168.1.77

Subnet Mask: 255.255.255.0

Default Gateway: 192.168.1.254

User Name: root

Password: root

System Login

1.Launch the Internet Explorer on the PC

24-Hour Technical Support: 1-800-260-1312

International: 00-1-952-941-7600

50

Transition Networks

MIL-SM2401MAF

2.Key in “http:// “+” the IP address of the switch”, and then Press “Enter”.

Uniform Resource Locator

3.The login screen appears right after.

Login screen

4.Key in the user name and password. The default user name and password are the same as ‘root’

5.Press Enter or click OK button, and then the home screen of the Web-based management shows up.

Port status

View every port status that depended on user setting and the negotiation result.

Port: Displays the port number.

Type: Displays the media type of the port.

Link: Down is “No Link”. UP is for “Link”.

State: Displays port status. Unlink will be regarded as “OFF”.

24-Hour Technical Support: 1-800-260-1312

International: 00-1-952-941-7600

51

Transition Networks

MIL-SM2401MAF

Negotiation: Displays the Auto Negotiation mode. Config column means that its value was configured by the user. Actual means the current value of the port.

Speed Duplex: Displays port connection speed. Config column means that its value was configured by the user. Actual means the current value of the port.

Flow Control: Displays the Flow Control status in full mode. Config column means that its value was configured by the user. Actual means the current value of the port.

Back Pressure: Displays the Back Pressure status. Config column means that its value was configured by the user. Actual means the current value of the port.

Bandwidth: Displays the in and out bandwidth of each port.

Priority: Displays the port static priority status.

Security: Displays the port security status.

Port Status interface

24-Hour Technical Support: 1-800-260-1312

International: 00-1-952-941-7600

52

Transition Networks

MIL-SM2401MAF

View the Port Information

Click the port on the switch panel figure on the web page and a port information window will show up as below:

Port information interface

Port Statistics

Display the current port statistic information

 

Scroll down for more ports statistics

 

Click

Clear

button to clean all counts

24-Hour Technical Support: 1-800-260-1312

International: 00-1-952-941-7600

53

Transition Networks

MIL-SM2401MAF

Port Statistics interface

Administrator

Administrator function provides the following functions—IP Configuration, Switch

Settings, Console Port Information, Port Controls, Trunking, Forwarding and Filtering, VLAN Configuration, Spanning Tree, Port Mirroring, SNMP Management, Security Manager, 802.1x Configuration, and System Log.

24-Hour Technical Support: 1-800-260-1312

International: 00-1-952-941-7600

54

Transition Networks

MIL-SM2401MAF

IP Address

Configure the IP address and DHCP client function.

DHCP Client: Enable or disable the DHCP client function. When DHCP client function is enabled, the switch will be assigned an IP address from the network DHCP server. Moreover, the default IP address will be replaced by the assigned IP address on DHCP server. After the user clicks Apply button, a popup window shows up. It is to inform the user that when the DHCP client is enabled, the current IP will lose and the user should find the new IP on the DHCP server.

IP Address: Assign the switch IP address. The default IP is 192.168.1.77

Subnet Mask: Assign the switch IP subnet mask

Gateway: Assign the switch gateway. The default value is 192.168.1.254

 

And then, click

Apply

button

 

Reboot the switch

 

IP configuration interface

Switch Setting

Basic

Displays the switch basic information

System Name: Displays the name of the switch.

System Location: Displays the switch physical location.

24-Hour Technical Support: 1-800-260-1312

International: 00-1-952-941-7600

55

Transition Networks

MIL-SM2401MAF

System Description: Displays the description of the switch.

Firmware Version: Displays the Firmware version of the switch.

Kernel Version: Displays the Kernel Software version.

Hardware version: Displays the Hardware version of the switch.

MAC Address: Displays the unique hardware address assigned by manufacturer (default).

Module: The module information. If the modules are not installed in the switch, this column will not be displayed.

Switch basic setting interface

Advanced

Enable MAC Address Aging Out: Tick the check box to enable MAC address aging out function.

Age-out Time: Key in the number of seconds that an inactive dynamic MAC address remains in the switch's address table. The valid range is from 300 ~ 765 seconds. The default value is 300 seconds.

Max Bridge Transmit Delay Bound: Limit the packets queuing time in the switch. If the delay bound is set, the packets exceeding the queue time will be dropped. The valid values are 1sec, 2 sec, 4 sec, and off.

24-Hour Technical Support: 1-800-260-1312

International: 00-1-952-941-7600

56

Transition Networks

MIL-SM2401MAF

Enable Low Queue Delay Bound: Limit the low priority packets queuing time in the switch. If the low priority packet stays in switch exceeding Max Delay Time, it will be sent. The valid range is from 1 ~ 255 ms.

[NOTE] Delay Bound must work under “Max bridge transit delay bound” function being in active status

Broadcast Storm Filter Mode: To configure broadcast storm control, enable it and set the upper broadcast storm threshold. The threshold is the percentage of the total packet buffer used by broadcast traffic. When broadcast traffic for a port rises above the threshold you set, broadcast storm control becomes active. The valid threshold values are 5%, 10%, 15%, 20%, 25% and off.

Click Apply button to complete the configuration.

Switch Advanced setting interface

24-Hour Technical Support: 1-800-260-1312

International: 00-1-952-941-7600

57

Transition Networks

MIL-SM2401MAF

Priority Queue Service settings: Select the priority queue service type.

801.1p Priority

First Come First Service: The sequence of packets sent depend on arriving order.

All High before Low: The high priority packets sent before low priority packets

Weighted Round Ratio: Select the preference given to packets in the switch's high-priority queue. These options represent the number of high priority packets sent before one low priority packet being sent. For example, 5

High: 1 Low means that the switch sends 5 high priority packets before

sending 1 low priority packet.

Qos Policy (Checked for High Priority): 0 ~ 7 priority level can map onto high or

low queue.

Misc Configuration

Collisions Retry Forever:

Disable (in half duplex): When collisions occur, the system will retry 48 times and then drop frame.

Enable (in half duplex): When collisions occur, the system will retry forever.

Hash Algorithm: CRC Hash or Direct Map for MAC address learning algorithm.

IFG Compensation: Enable or disable Inter Frame Gap time compensation.

802.1x Protocol: Enable or disable 802.1x protocol.

IGMP Query Mode: Recognizes different queries from clients or servers to decide

which Query will be the first priority. The modes are:

a.Auto Mode: Choose the switch that has the lowest IP address to be set as the IGMP Query mode.

b.Enable Mode: Enables the switch to be the IGMP Querier.

c.Disable Mode: Disables the query function of the switch.

24-Hour Technical Support: 1-800-260-1312

International: 00-1-952-941-7600

58

Transition Networks

MIL-SM2401MAF

Switch Misc Config setting interface

Console Port Information

Console is a standard UART interface to communicate with Serial Port. Use windows HyperTerminal program to link the switch. Please refer to Console Management Console login for detail steps.

Console port information displays as follow:

Bits per seconds: 9600

Data bits: 8

Parity: none

Stop Bits: 1

Flow control: none

Console Port Information interface

24-Hour Technical Support: 1-800-260-1312

International: 00-1-952-941-7600

59

Transition Networks

MIL-SM2401MAF

Port Controls

Change the port status

Select the port by scroll the list in Port column

State: Current port status. The port can be set to disable or enable mode. If the port state is set as ‘Disable’, it will not receive or transmit any packet.

Negotiation: Auto and Force. Being set as Auto, the speed and duplex mode are negotiated automatically. When you set it as Force, you have to assign the speed and duplex mode manually.

Speed: It is available for selecting when the Negotiation column is set as Force. When the Negotiation column is set as Auto, this column is read only.

Duplex: It is available for selecting when the Negotiation column is set as Force. When the Negotiation column is set as Auto, this column is read only.

Flow Control: Set flow control function as Enable or Disable. When enabled, once the device exceed the input data rate of another device as a result the receiving device will send a PAUSE frame which halts the transmission of the sender for a specified period of time. When disabled, the receiving device will drop the packet if too much to process.

Back Pressure: Set Back Pressure as ON or OFF in Half Duplex mode.

Band Width: All ports support port ingress and egress rate control. For example, assume the wire speed of port 1 is 100Mbps; users can set its effective egress rate as 2Mbps, ingress rate as 1Mbps. The switch will perform Flow Control or Back Pressure to confine the ingress rate to meet the specified rate.

In: Key in the port effective ingress rate. The valid range is from 0 ~ 999. 0 means rate control is disabled.

Out: Key in the port effective egress rate. The valid range is from 0 ~ 999. 0 means rate control is disabled.

Priority: The static priority is based on port. If the port is set as high priority, income frames from the port always are high priority frame.

Security: When the port is in security mode, the port will be “locked” without permission of address learning. Only the incoming packets with static MAC

already existing in the address table can be forwarded normally. User can disable

24-Hour Technical Support: 1-800-260-1312

International: 00-1-952-941-7600

60

Transition Networks

MIL-SM2401MAF

the port from learning any new MAC addresses, and then use the static MAC addresses function to define a list of MAC addresses that can access to secure port.

Click Apply button to apply all configuration.

The port current configuration also will be displayed when the port is selected.

Port Control interface

Trunking

The Link Aggregation Control Protocol (LACP) provides a standardized means for exchanging information between Partner Systems on a link to allow their Link Aggregation Control instances to reach agreement on the identity of the Link Aggregation Group to which the link belongs, move the link to that Link Aggregation Group, and enable its transmission and reception functions in an orderly manner. Link aggregation lets you group up to 4 ports into one dedicated connections. This feature can expand bandwidth to a device on the network. LACP operation requires full-duplex mode, more detail information refers to IEEE 802.3ad.

Aggregator setting

System Priority: A value which is used to identify the active LACP. The switch

with the lowest value has the highest priority and is selected as the active LACP.

24-Hour Technical Support: 1-800-260-1312

International: 00-1-952-941-7600

61

Transition Networks

MIL-SM2401MAF

Group ID: There are four trunk groups to be selected. Choose the "Group ID" and click Select button.

LACP: When enabled, the trunk group is using LACP. A port which joins an LACP trunk group has to make an agreement with its member ports first. When disabled, the trunk group is a static trunk group. The advantage of having the LACP disabled is that a port joins the trunk group without any handshaking with its member ports. But member ports won’t know that they should be aggregated together to form a logic trunk group.

Work ports: This column field allows the user to type in the total number of active port up to four. With LACP trunk group, you create a trunk group by connecting two or more switches (e.g. you assign four ports to be the members of the trunk group whose work ports column field is set as two). The exceed ports are standby (the Aggregator Information tab will show standby status on the exceed ports) and can be aggregated if work ports fail. If it is a static trunk group, the number of work ports must equal the total number of group member ports.

Select the ports to join the trunk group. The system allows four ports maximum to

be aggregated in a trunk group. Click Add button to add the port which is focused to the left field. To remove unwanted ports, select the port and click

Remove button.

When LACP enabled, you can configure LACP Active/Passive status for each port on State Activity page.

Click Apply button.

 

Use

Delete

button to delete Trunk Group. Select the Group ID and click

Delete

button.

24-Hour Technical Support: 1-800-260-1312

International: 00-1-952-941-7600

62

Transition Networks

MIL-SM2401MAF

Trunking—Aggregator Setting interface

Aggregator Information

When you have setup the aggregator setting with LACP disabled, you will see the local static trunk group information in here.

Group Key: Displays the trunk group ID.

Port Member: Displays the members of this static trunk group.

Trunking—Aggregator Information interface

24-Hour Technical Support: 1-800-260-1312

International: 00-1-952-941-7600

63

Transition Networks

MIL-SM2401MAF

Aggregator State Activity

Having set up the LACP aggregator on the tab of Aggregator Setting, you can configure the state activity for the members of the LACP trunk group. You can tick or cancel the checkbox beside the state display. When you remove the tick mark to the

port and click

Apply

button, the port state activity will change to Passive.

Active: The port automatically sends LACP protocol packets.

Passive: The port does not automatically send LACP protocol packets, and responds only if it receives LACP protocol packets from the opposite device.

[NOTE] 1. A link having either two active LACP nodes or one active node can

perform dynamic LACP trunk.

2.A link having two passive LACP nodes will not perform dynamic LACP trunk because both ports are waiting for an LACP protocol packet from the opposite device.

Trunking – State Activity interface

24-Hour Technical Support: 1-800-260-1312

International: 00-1-952-941-7600

64

Transition Networks

MIL-SM2401MAF

Forwarding and Filtering

IGMP Snooping

The Internet Group Management Protocol (IGMP) is an internal protocol of the Internet Protocol (IP) suite. IP manages multicast traffic by using switches, routers, and hosts that support IGMP. Enabling IGMP allows the ports to detect IGMP queries, report packets, and manage IP multicast traffic through the switch. IGMP have three fundamental types of message shown as follows:

 

 

 

 

 

Message

Description

 

 

 

 

 

 

 

A message sent from the querier (IGMP router or switch)

 

 

Query

asking for a response from each host belonging to the

 

 

 

multicast group.

 

 

 

A message sent by a host to the querier to indicate that the

 

 

Report

host wants to be or is a member of a given group indicated in

 

 

 

 

 

 

the report message.

 

 

 

 

 

 

Leave

A message sent by a host to the querier to indicate that the

 

 

 

 

 

Group

host has quit being a member of a specific multicast group.

 

 

 

 

 

 

 

 

 

 

 

 

The switch supports IP multicast. You can enable IGMP protocol via setting the IGMP Configuration page to see the IGMP snooping information. IP multicast addresses are in the range of 224.0.0.0 through 239.255.255.255.

IGMP Protocol: Enable or disable the IGMP protocol.

IGMP Query: Select the IGMP query function as Enable or Auto to set the switch as a querier for IGMP version 2 multicast networks.

Click Apply button.

24-Hour Technical Support: 1-800-260-1312

International: 00-1-952-941-7600

65

Transition Networks

MIL-SM2401MAF

IGMP Snooping interface

Static MAC Address

When the user adds a static MAC address which will remains in the switch's address table, regardless of whether the device is physically connected to the switch. This saves the switch from having to re-learn a device's MAC address when the disconnected or powered-off device is active on the network again.

MAC Address: Enter the MAC address of the port that should permanently forward traffic, regardless of the device network activity.

Port Number: Select a port number.

VLAN ID: If tag-based (802.1Q) VLAN are set up on the switch, key in the VID in the VLAN ID box to associate with the MAC address.

 

And then, click Add button.

 

To delete MAC address, press

Delete

button

24-Hour Technical Support: 1-800-260-1312

International: 00-1-952-941-7600

66

Transition Networks

MIL-SM2401MAF

Static MAC Address interface

MAC filtering

MAC address filtering allows the switch to drop unwanted traffic. Traffic is filtered

based on the destination addresses.

MAC Address: Enter the MAC address that you want to filter.

VLAN ID: If tag-based (802.1Q) VLAN are set up on the switch, key in the VID in the VLAN ID field to associate with the MAC address.

 

And then, click Add button

 

To delete MAC address, press

Delete

button

24-Hour Technical Support: 1-800-260-1312

International: 00-1-952-941-7600

67

Transition Networks

MIL-SM2401MAF

MAC Filtering interface

VLAN configuration

A Virtual LAN (VLAN) is a logical network grouping that limits the broadcast domain, which would allow you to isolate network traffic, so only the members of the same VLAN will receive traffic from the ones of the same VLAN. Basically, creating a VLAN from a switch is logically equivalent of reconnecting a group of network devices to another Layer 2 switch. However, all the network devices are still plugged into the same switch physically.

The switch supports Port-based and 802.1Q (tagged-based) VLAN. The default configuration of VLAN operation mode is “Disable”.

[NOTE] To reboot the switch when the VLAN mode is changed

Port-based VLAN

Packets can go among only members of the same VLAN group. Note all unselected

24-Hour Technical Support: 1-800-260-1312

International: 00-1-952-941-7600

68

Transition Networks

MIL-SM2401MAF

ports are treated as belonging to another single VLAN. If the port-based VLAN enabled, the VLAN-tagging is ignored.

In order for an end station to send packets to different VLAN groups, it itself has to be either capable of tagging packets it sends with VLAN tags or attached to a VLAN-aware bridge that is capable of classifying and tagging the packet with different VLAN ID based on not only default PVID but also other information about the packet, such as the protocol.

Click the hyperlink “Configuration” to enter the VLAN configuration interface

VLAN – PortBase interface

 

And then, click

Add

to create a new VLAN group

24-Hour Technical Support: 1-800-260-1312

International: 00-1-952-941-7600

69

Transition Networks

MIL-SM2401MAF

VLAN—PortBase Add interface

Key in the VLAN name, VLAN ID and select the members for the VLAN group.

 

And then, click

Apply

24-Hour Technical Support: 1-800-260-1312

International: 00-1-952-941-7600

70

Transition Networks

MIL-SM2401MAF

The VLAN groups will be displayed in table

To view the VLAN groups in next page, press Next Page to the next page

To delete VLAN groups, press

To modify VLAN groups, click

Delete

button

Edit

button

[Note] If the trunk groups have been configured, the trunk groups will list in the port list (For example: Trunk1, Trunk2…). The trunk group also can be configured as the VLAN member.

802.1Q VLAN

Tagged-based VLAN is an IEEE 802.1Q specification standard. Therefore, it is possible to create a VLAN across devices from different switch venders. IEEE 802.1Q VLAN uses a technique to insert a “tag” into the Ethernet frames. Tag contains a VLAN Identifier (VID) that indicates the VLAN numbers.

24-Hour Technical Support: 1-800-260-1312

International: 00-1-952-941-7600

71

Transition Networks

MIL-SM2401MAF

You can create Tag-based VLAN, and enable or disable GVRP protocol. There are 256 VLAN groups to provide configuration. Enable 802.1Q VLAN, all ports on the switch belong to default VLAN of VID 1. The default VLAN can’t be deleted.

GVRP (GARP VLAN Registration Protocol) is a protocol that facilitates control of virtual local area networks (VLANs) within a larger network. GVRP conforms to the IEEE 802.1Q specification, which defines a method of tagging frames with VLAN configuration data. This allows network devices to dynamically exchange VLAN configuration information with other devices.

GVRP is based on GARP (Generic Attribute Registration Protocol), a protocol that defines procedures by which end stations and switches in a local area network (LAN) can register and de-register attributes, such as identifiers or addresses, with each other.

Every end station and switch thus has a current record of all the other end stations and switches that can be reached.

802.1q VLAN interface

Click the hyperlink “Configuration” to enter the VLAN configuration interface.

Enable GVRP Protocol: Ticked the check box to enable GVRP protocol.

Enable security VLAN setting: Tick the check box to enable security VLAN group. When you select to enable security VLAN group, only the members in this

24-Hour Technical Support: 1-800-260-1312

International: 00-1-952-941-7600

72

Transition Networks

MIL-SM2401MAF

VLAN group can access the switch. The steps of setting security VLAN refer to the following below steps in Basic section. After the security VLAN group has been configured, you can add other VLAN groups.

[Note] Only one security VLAN group is allowed.

 

Basic

 

 

Click Add

button.

 

Group Name: Assign a name for the new VLAN.

 

VLAN ID: Key in a VLAN ID (1-4094). The default is 1.

 

Protocol VLAN: Choose the protocol type. Default is NONE.

802.1q VLAN –Add interface

Group the ports, and then click Add button. If the trunk groups have been

24-Hour Technical Support: 1-800-260-1312

International: 00-1-952-941-7600

73

Transition Networks

MIL-SM2401MAF

configured, the trunk groups will list in the port list (For example: Trunk1, Trunk2…). The trunk group also can be configured as the VLAN member.

 

And then, click

Next

will see the page as below:

24-Hour Technical Support: 1-800-260-1312

International: 00-1-952-941-7600

74

Transition Networks

MIL-SM2401MAF

 

Set the outgoing frames as VLAN-Tagged frames or untagged.

 

 

Tag: The outgoing frames involve VLAN tag.

 

 

Untag: The outgoing frames don’t involve VLAN tag.

 

And then, click

Apply

button.

Port VID: Configure port VID.

VLAN ID: Set the port VLAN ID that will be assigned to untagged traffic on a given port. This feature is useful for accommodating devices that you want them to join in the VLAN which doesn’t support tagging. Each port of the switch allows the user to set one VLAN ID (the range is from 1 ~ 255 and the default VLAN ID is 1). The VLAN ID must be as same as the VLAN ID of the VLAN group that the port belongs to, or the untagged traffic will be dropped.

Ingress Filtering: Ingress filtering lets frames belonging to a specific VLAN to be forwarded if the port belongs to that VLAN.

Enable: Forward only when the packets with VID match the configured VID of this port.

Disable: Disable Ingress filter function.

Acceptable Frame type:

24-Hour Technical Support: 1-800-260-1312

International: 00-1-952-941-7600

75

Transition Networks

MIL-SM2401MAF

ALL: Acceptable all Packet.

Tag Only: Only packets with matched VLAN ID have the permission to go through the port.

 

And then, click

Apply

button.

802.1q VLAN – Port VLAN ID interface

Spanning Tree

The Spanning-Tree Protocol (STP) is a standardized method (IEEE 802.1d) for avoiding loops in switched networks. When STP enabled, to ensure that only one path at a time is active between any two nodes on the network. It’s recommended to enable STP on all switches to ensure only one active path on the network.

The Rapid Spanning Tree Protocol (RSTP) is an evolution of the Spanning Tree Protocol and provides for faster spanning tree convergence after a topology change. The system also supports STP and the system will auto-detect the connected device that is running STP or RSTP protocol.

24-Hour Technical Support: 1-800-260-1312

International: 00-1-952-941-7600

76

Transition Networks

MIL-SM2401MAF

System Configuration

User can choose the RSTP mode and view Root Bridge information.

Modifying STP state:

RSTP Mode: Set RSTP mode as 802.1d or 802.1w.

Priority (0-61440): The switch with the lowest value has the highest priority and is selected as the root. If the value is changed, the user must reboot the switch. The value must be a multiple of 4096 according to the protocol standard rule.

Max Age (6-40): The number of seconds a switch waits without receiving Spanning-tree Protocol configuration messages before attempting a reconfiguration. Enter a value between 6 through 40.

Hello Time (1-10): The time that controls the switch to send out the BPDU packet to check RSTP current status. Enter a value between 1 through 10.

Forward Delay Time (4-30): The number of seconds a port waits before changing from its Rapid Spanning-Tree Protocol learning and listening states to the forwarding state. Enter a value between 4 through 30.

 

And then, click

Apply

button.

24-Hour Technical Support: 1-800-260-1312

International: 00-1-952-941-7600

77

Transition Networks

MIL-SM2401MAF

Spanning Tree – System Configuration interface

Per Port Configuration

Configure path cost and priority of every port

Select the port in Port column.

Path Cost: The cost of the path to the other bridge from this transmitting bridge at the specified port. Enter a number 1 through 200,000,000.

Priority: Decide which port should be blocked by priority in LAN. Enter a number 0 through 240 (the port of the highest value will be blocked). The value of priority must be the multiple of 16.

Admin P2P: Some of the rapid state transactions that are possible within RSTP are dependent upon whether the port concerned can only be connected to exactly one other bridge (i.e. it is served by a point-to-point LAN segment), or can be connected to two or more bridges (i.e. it is served by a shared medium LAN segment). This function allows the P2P status of the link to be manipulated administratively. True is P2P enabling. False is P2P disabling.

24-Hour Technical Support: 1-800-260-1312

International: 00-1-952-941-7600

78

Transition Networks

MIL-SM2401MAF

Admin Edge: The port directly connected to end stations won’t create bridging loop in the network. To configure the port as an edge port, set the port to “True” status.

Admin Non Stp: The port includes the STP mathematic calculation. True is not including STP mathematic calculation. False is including the STP mathematic calculation.

 

And then, click

Apply

button.

24-Hour Technical Support: 1-800-260-1312

International: 00-1-952-941-7600

79

Transition Networks

MIL-SM2401MAF

SPT – Per Port Configuration interface

Port Mirroring

The Port mirroring is a method for monitor traffic in switched networks. Traffic through ports can be monitored by one specific port which means traffic goes in or out monitored (source) ports will be duplicated into mirroring (analysis) port.

24-Hour Technical Support: 1-800-260-1312

International: 00-1-952-941-7600

80

Transition Networks

MIL-SM2401MAF

Prot Mirroring interface

Port Mirroring State: Set mirroring mode—Disable, RX, TX, and Both.

Analysis Port: Select one port to be the analysis port which can be used to see all monitored port traffic. User can connect mirror port to LAN analyzer or Netxray.

Monitor Port: Tick the check box to monitor port traffic which will be copied to mirror (analysis) port (The maximum monitored ports are 25).

[NOTE] If you want to disable the function, you must select analysis port to none.

24-Hour Technical Support: 1-800-260-1312

International: 00-1-952-941-7600

81

Transition Networks

MIL-SM2401MAF

 

 

 

SNMP Management

The SNMP is a Protocol that governs the transfer of information between management and agent. The switch supports SNMP V1.

Define management stations as trap managers and to enter SNMP community strings.

System Options: Assign the name, location, contact information of the switch.

Name: Key in a name for the switch.

Location: Key in the switch physical location.

Contact: Key in the name of contact person or organization.

SNMP Management interface

Community strings: Serve as password.

24-Hour Technical Support: 1-800-260-1312

International: 00-1-952-941-7600

82

Transition Networks

MIL-SM2401MAF

Strings: Key in the name of string.

RO: Enable requests accompanied by this string to display MIB-object information (Read only).

RW: Enable requests accompanied by this string to display MIB-object information and to set MIB objects (Read/Write).

 

And then, click

Add

button.

 

Trap Manager

 

 

A trap manager is a management station that receives traps. The management station then generates alerts based on the received traps. If no trap manager is defined, no traps are issued. Create a trap manager by entering the IP address of the station and a community string.

IP Address: Key in IP address of the trap manager.

 

Community Strings: Key in the community strings

 

And then, click Add

button.

Security Manager

Change management login user name and password

User name: Key in the new user name (the default is root).

New Password: Key in the new password (the default is root).

 

Confirm password: Enter the new password again.

 

And then, click

Apply

button.

24-Hour Technical Support: 1-800-260-1312

International: 00-1-952-941-7600

83

Transition Networks

MIL-SM2401MAF

Security Manager interface

SNTP Configuration

Configure the SNTP (Simple Network Time Protocol) setting which SNTP allows the switch to synchronize switch clocks in the Internet. Use this page to Enable/Disable SNTP client; set SNTP server IP address, and UTC (Coordinated Universal Time) timezone.

SNTP Client: Enable or disable SNTP function to get the time from the SNTP server.

UTC Timezone: Enter between -12 and +13 in the UTC Timezone field. For example, 8.5 means UTC +8.5 hours.

Server IP: Assign the SNTP server IP address.

Switch Timer: Displays the current time of the switch.

SNTP Configuration Interface

24-Hour Technical Support: 1-800-260-1312

International: 00-1-952-941-7600

84

Transition Networks

MIL-SM2401MAF

802.1X Configuration

When the IEEE 802.1X protocol is enabled, user can configure the parameters of

802.1X. To enable the IEEE 802.1X protocol, go to Administrator Switch Setting

Misc Config

System Configuration

Radius Server IP: Set the Radius Server IP address.

Server Port: Set the UDP destination port for authentication requests to the specified Radius Server.

Accounting Port: Set the UDP destination port for accounting requests to the specified Radius Server.

Shared Key: Set an encryption key for use during authentication sessions with the specified radius server. This key must match the encryption key used on the Radius Server.

NAS, Identifier: Set the identifier for the radius client.

 

And then, click

Apply

button.

802.1x Configuration—System Configuration interface

24-Hour Technical Support: 1-800-260-1312

International: 00-1-952-941-7600

85

Transition Networks

MIL-SM2401MAF

Per port Configuration

Select the port in Port column

Select the state of port:

Reject: The specified port is required to be held in the unauthorized state.

Accept: The specified port is required to be held in the Authorized state.

Authorized: The specified port is set to the Authorized or Unauthorized state in accordance with the outcome of an authentication exchange between the Supplicant and the authentication server.

Disable: When disabled, the specified port works without complying with 802.1x protocol.

 

And then, click

Apply

button.

24-Hour Technical Support: 1-800-260-1312

International: 00-1-952-941-7600

86

Transition Networks

MIL-SM2401MAF

802.1x Configuration—Per Port Configuration

Misc Configuration

Quiet Period: Set the period which the port doesn’t try to acquire a supplicant.

TX Period: Set the period the port waits for retransmit next EAPOL PDU during an authentication session.

Supplicant Timeout: Set the period of time the switch waits for a supplicant response to an EAP request.

Server Timeout: Set the period of time the switch waits for a server response to an authentication request.

Max Requests: Set the number of authentication that must time-out before authentication fails and the authentication session ends.

Reauth period: Set the period of time which clients connected must be re-authenticated.

 

And then, click

Apply

802.1x Configuration – Misc Configuration interface

System Log

Configure the system event mode to collect system log.

24-Hour Technical Support: 1-800-260-1312

International: 00-1-952-941-7600

87

Transition Networks

MIL-SM2401MAF

System Log Client Mode: Select the system log mode—Client Only, Server Only, or Both.

System Log Server IP Address: Assign the system log server IP.

When Syslog Client Mode is set as Client Only, the system event log will only be reserved in the switch’s RAM until next reboot. When Syslog Client Mode is set as Server Only, the system log will only be sent to the syslog server and you have to type the IP address in the Sysylog Server IP Address column. If the Syslog Client Mode is set as Both, the system log will be reserved in the switch’s RAM and sent to server.

Click Reload to refresh the events log.

 

Click

Clear

to clear all current events log.

 

After configuring, Click Apply .

24-Hour Technical Support: 1-800-260-1312

International: 00-1-952-941-7600

88

Transition Networks

MIL-SM2401MAF

System Log Interface

Save Configuration

Save the configuration to the flash memory when the configurations have been changed. If users want to keep their configuration after rebooting the switch, they must save the configuration. Otherwise, the new configuration will be lost when the switch restart or power off.

Click the Save Configuration button to save the configuration to the flash memory.

Save Configuration Interface

TFTP Update Firmware

Use this page (TFTP—Trivial File Transfer Protocol) to configure to update the switch’s flash image bank.

Place the updated image file on the TFTP server.

TFTP Server IP Address: Key in TFTP server IP address.

Firmware File Name: The name of firmware image.

And then, click Apply button; the switch will download the new image file from TFTP server.

24-Hour Technical Support: 1-800-260-1312

International: 00-1-952-941-7600

89

Transition Networks

MIL-SM2401MAF

TFTP Update Firmware interface

Configuration Backup

Restore the backup configuration from TFTP server to the switch. Also, user can backup the configuration to TFTP server.

TFTP Restore Configuration

Restore the stored configuration file from TFTP server.

Place the stored configuration file on the TFTP server.

TFTP Server IP Address: Key in the TFTP server IP address.

 

Restore File Name: Key in the correct restore file image name.

 

And then, click

Apply

button.

24-Hour Technical Support: 1-800-260-1312

International: 00-1-952-941-7600

90

Transition Networks

MIL-SM2401MAF

TFTP Restore Configuration interface

TFTP Backup Configuration

Save current flash ROM value from the switch to TFTP server.

TFTP Server IP Address: Key in the TFTP server IP address.

 

Backup File Name: Key in the file image name.

 

And then, click

Apply

button.

TFTP Backup Configuration interface

Factory Default

Reset Switch to default configuration.

Default IP address: 192.168.1.77

 

Default Gateway: 192.168.1.254

 

Subnet mask: 255.255.255.0

 

Click

Default

button to reset switch to default setting.

24-Hour Technical Support: 1-800-260-1312

International: 00-1-952-941-7600

91

Transition Networks

MIL-SM2401MAF

Factory Default interface

System Reboot

Reboot the Switch in software reset.

Click Reboot button to reboot the switch.

System Reboot interface

Power Status

View the connected UPS information and set command to UPS.

Power Status Interface

24-Hour Technical Support: 1-800-260-1312

International: 00-1-952-941-7600

92

Transition Networks

MIL-SM2401MAF

UPS information: The information will be available when the UPS is connected to the switch and the connection is normal and UPS is powered on.

Click Refresh button to refresh.

Input Voltage: Displays the current value, minimum, and maximum value of UPS input voltage.

Output Voltage: Displays the current value, minimum, and maximum value of UPS output voltage.

Frequency: Display the frequency value of UPS.

Battery Capacity: Displays the battery capacity of UPS.

UPS Overload: Displays the overload capacity of UPS.

Temperature: Displays the current temperature of UPS.

RatVoltage: Displays Range of the UPS voltage.

RatBtyVoltage: Displays Range of the UPS battery voltage.

RatCurrent: Displays Range of the UPS current.

RatFrequency: Displays Range of the UPS frequency.

Model: Model name of the UPS.

Version: UPS internal software version.

The figure represents the UPS status, when the status has been detected; the figure color will change from yellow to red and the status description will change, too.

PoE Status

View PoE port information and set configuration to each port.

24-Hour Technical Support: 1-800-260-1312

International: 00-1-952-941-7600

93

Transition Networks

MIL-SM2401MAF

Select the port and set configuration.

And then, click Apply button.

 

Press the

Refresh

button to refresh.

PoE Status Interface

Power Limit Management: Enable/disable the PoE power management function.

Firmware: Displays the system firmware version.

Total Power Limit: Set limit value of the total provided power to the PDs.

Total Power (W): Displays the total power of all the port that provided to PDs.

Port: Select the port you want to configure.

Enable: Enable or disable the port status.

Bypass Detection: Generally, this check box should not be ticked. Once this check box is ticked, the port will provide power without detecting whether the connected device is a PD or not.

Power Limit by Classification: Tick this check box to enable/disable

24-Hour Technical Support: 1-800-260-1312

International: 00-1-952-941-7600

94