Transition Networks FAST ETHERNET E-TX-MC01 User Manual

98.63 Kb
Loading...

TRANSCEIVER TECHNICAL SPECIFICATIONS

Standards

IEEE 802.3

 

Case dimensions

2.8" x 1.75" x 0.75" (71mm x 43mm x 18mm)

Maximum in series:

Two (2)

 

Environment

Temperature:

0-40°C (32° to 104° F )

 

Humidity

10-90%, non condensing

 

Altitude

0-10,000 feet

Warranty

Five years

 

Setting the Transceiver Physical Address

Additive switch settings allow a physical address to be set by selecting (or not selecting) among the following:

Switch 1 DOWN

20

1

Address (1-5)

 

 

 

1 2 3

4

5

6

7

Switch 2 DOWN

21

2

Switch 3 DOWN

22

4

 

 

 

 

 

Switch 4 DOWN

23

8

 

 

 

 

 

Switch 5 DOWN

24

16

O F F

O F F

 

 

In the switch setting shown above, the

 

 

 

 

 

 

 

transceiver physical address is set to 1 (1+0+0+0+0).

 

 

 

 

NOTE: 1=ON, 0=OFF

 

 

 

 

 

 

 

Compliance Information

UL Listed

C-UL Listed (Canada)

CISPR/EN55022 Class A

FCC Regulations

This equipment has been tested and found to comply with the limits for a class A digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case the user will be required to correct the interference at the user’s own expense.

Canadian Regulations

This digital apparatus does not exceed the Class A limits for radio noise for digital apparatus set out on the radio interference regulations of the Canadian Department of Communications.

European Regulations

Warning

This is a Class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures.

Copyright Restrictions

© 1998 TRANSITION Networks.

All rights reserved. No part of this work may be reproduced or used in any form or by any means – graphic, electronic, or mechanical – without written permission from TRANSITION Networks.

Trademark Notice

All registered trademarks and trademarks are the property of their respective owners.

33097.B

Minneapolis, MN 55344 USA

Fast Ethernet™ Copper Transceiver

E-TX-MC01

USER’S GUIDE

TRANSITION Networks copper transceivers (E-TX-MC01) connect Fast Ethernet™ hubs and/or terminal devices, through a Media Independent Interface (MII) connector, to 10BASE-T copper cable or to 100BASE-TX copper cable.

E-TX-MC01

Provides an MII connector and an RJ45 10BASE- T/100BASE-TX connector to unshielded twistedpair or shielded twisted-pair copper cable.

Config. Switches

1 2 3

4 5 6 7

MDI MDI-X

PL/FDX

UTP/STP Copper

E-TX-MC01

A set of switches on the front of the transceiver can be used to set a unique physical address for each transceiver. Transceivers can be configured to

autonegotiate or to force either 10Mb/sec half-duplex mode or 100Mb/sec half-duplex mode.

An MDI/MDI-X switch on the side of the transceiver can be used to set the copper cable configuration to straight-through or to crossover.

Status LEDs provide the following information:

Address (1-5)

PL/FDX

Illuminated green LED indicatesthe

 

 

 

1

 

2

3

4

5

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

transceiver is operating in full-duplex

 

 

 

 

Collision

 

 

 

 

 

 

10/100

mode.

 

 

 

 

 

RX

TX

Link

 

 

 

 

Illuminated green LED indicates the

 

 

 

 

 

 

 

 

 

 

transceiver is operating at 100Mb/s.

 

 

 

 

 

 

 

 

 

ON

OFF

Power

 

 

PL/FDX

 

10/100

100BASE-TX TRANSCEIVER

E-TX-MC01

 

Collision

 

RX

TX

Collision:

Illuminated green LED indicates

Link

Power

 

signal collisions on the Ethernet

 

 

 

cable.

 

RX

Flashing or illuminated green LED indicates packet(s) are being received.

TX

Flashing or illuminated green LED indicates packet(s) are being transmitted.

Link

Illuminated green LED indicates the unit is receiving link pulses from a

 

compliant device.

 

Power:

Illuminated green LED indicates connection to external power

+ 1 hidden pages