Installation Guide
Outdoor CPE
CPE210 / CPE220 / CPE510 / CPE520
Contents
Overview |
01 |
Hardware Connection |
04 |
Site Consideration |
04 |
Connection and Installation |
06 |
Lightning & ESD Protection |
08 |
Software Configuration |
10 |
Logging in to the PharOS |
10 |
Typical Application Configuration |
12 |
Antenna Alignment |
14 |
Specifications |
15 |
FAQ |
16 |
Overview
TP-Link's Pharos series outdoor CPEs are dedicated to outdoor wireless network solutions. This guide is applicable to products including CPE210, CPE220, CPE510 and CPE520.
• Package Contents
Power Cord |
Pole Mounting |
|
Straps |
||
|
|
|
|
Installation Guide |
|
|
|
Outdoor CPE |
|
|
|
CPE210 / CPE220 / CPE510 / CPE520 |
Pharos CPE |
Passive PoE |
Mounting Bracket |
Installation Guide |
Plastic Wall Anchors (Qty.2) |
|||
|
Adapter |
Self-tapping Screws (Qty.2) |
|
• LED Explanation
The following picture takes CPE520 as an example.
AP/AP Router mode:
All four LEDs remain solid.
Client/Bridge/Repeater/AP Client Router mode:
That the more LEDs lit will indicate better wireless signal strength.
RPOWE LAN0 LAN1
On: A device is connected to this port, but there is no activity. Flashing: A device is connected to this port, and is active.
On: The CPE is powered on.
01
• Panel Layout
Pharos CPE220/CPE520:
Grounding |
Shielded Ethernet |
Shielded Ethernet |
RESET |
Terminal |
Port LAN0 (Passive |
Port LAN1 |
|
|
PoE in) |
|
|
Pharos CPE210/CPE510:
Grounding |
Shielded Ethernet Port |
RESET |
Terminal |
LAN (Passive PoE in) |
|
02
Passive PoE Adapter:
Remote Reset
Press and hold for 8 seconds to reset the CPE to its factory defaults.
Power LED
The Power LED is on when the passive PoE adapter is working normally.
03
Hardware Connection
1. Site Consideration
• Mounting Height
Ensure a clear line of sight between the wireless devices for an optimum performance. An elevated location is recommended as obstacles like trees, buildings and large steel structures will weaken the wireless signal.
See 'Q2' in 'FAQ' for details about how to calculate the minimum mounting height of the devices.
Line of Sight
Side View
04
• Orientation
Install the CPE devices with the front facing the intended signal receiving devices. You can orient the devices with the assistance of Google Maps, GPS and some landmarks according to the horizontal beamwidth listed below.
Models |
CPE210 |
CPE220 |
CPE510 |
CPE520 |
Horizontal Beamwidth |
65° |
60° |
45° |
45° |
shenzhen
A
|
of |
Sight |
Line |
|
|
|
|
HorizontalBeamwidth
B
05
2. Connection and Installation
Connect and mount the CPE and power adapter as shown below. The following introduction takes CPE520 as an example.
• Connecting CPE and Power Adapter
Connect the CPE and power adapter as shown in the figure below.
LAN0
PoE LAN
Ethernet cable length up to 60m
Slide to replace the cover of the CPE when all connections are finished.
You should prepare an adequate Ethernet cable to connect the CPE and the passive PoE adapter. Shielded CAT5e (or above) cable with ground wire is recommended (refer to the next section).
Connect to a computer, router or switch. (Depending on your intended usage and/or network topology.)
06