Toshiba D1333-32, D1334-32 User Manual

Connection

(Not supped)li

0 (0)

English

Get started with Freeview

Freeview gives you over 50 TV channels to play with, not to mention 25 radio stations.

Start watching all your favourite TV content today, just connect your aerial and tune in.

Keep up-to-date

New channels are launched on Freeview from time to time along with other updates to the service. So it pays to retune your digital TV periodically to make sure your Digital TV/Radio channels are up to date. To retune your Toshiba Digital TV, please refer to the Re-tune section for guidance.

Alternatively find out more on the dedicated Freeview website:

www.freeview.co.uk/retune

Freeview service is subject to availability. Aerial upgrade may be required.

English - 1 -

English

Contents
Safety Precautions..................................................	4
Air Circulation......................................................	4
Heat Damage......................................................	4
Mains Supply.......................................................	4
Warning ..............................................................	4
Do........................................................................	4
Do not..................................................................	4
Installation and Important Information.....................	5
EXCLUSION CLAUSE........................................	5
Important safety information ...................................	6
Removing the pedestal stand..................................	7
The Remote Control (TV - DVD).............................	8
Inserting Batteries and Effective Range of the
Remote Control...................................................	8
Connecting External Equipment..............................	9
Connecting an HDMI® or DVI Device to the HDMI
Input......................................................................	10
To Connect an HDMI Device.............................	10
To Connect a DVI Device..................................	10
To Connect a Computer.....................................	11
Connecting a USB Memory....................................	11
To Connect a USB Flash Drive...........................	11
Connecting a Computer.........................................	11
Power Save Mode.................................................	12
Environmental Information ...............................	12
Controlling the TV.................................................	13
Switching on......................................................	13
Using the Remote Control.................................	13
Using the Controls on the TV............................	13
Initial Installation ...................................................	14
Auto Tuning.......................................................	15
Auto Tuning...........................................................	15
Manual Tuning, Analogue Fine Tuning..................	16
Digital Aerial Manual Search.............................	16
Digital Cable Manual Search.............................	16
Analogue Manual Search..................................	16
Analogue Fine Tune..........................................	16
Re-tune Section....................................................	17
Re-tuning: TOSHIBA Freeview Products..............	17
General Operation.................................................	18
Stereo and Bilingual Transmissions..................	18
Displaying Subtitles...........................................	18
Viewing Main Menu...........................................	18
Controlling Volume and Muting Sound..............	18
Selecting Programme Positions........................	18
Standby Notifications.........................................	18
Channel List, Sorting Programmes, Programme
Locking..................................................................	19
Viewing Channel List.........................................	19
Moving a Channel.............................................	19
Deleting a Channel............................................	19
Renaming a Channel.........................................	19

Locking a Channel.............................................	19
Viewing Info Banner, Electronic Programme
Guide.....................................................................	20
Viewing Info Banner..........................................	20
Electronic Programme Guide............................	20
Language Selection..............................................	21
Language Settings............................................	21
Preferred.......................................................	21
Current..........................................................	21
Digital Settings - Parental Control, Menu Lock,
Set PIN..................................................................	22
Viewing Parental Control Menu.........................	22
Menu Lock.........................................................	22
Maturity Lock (*)................................................	22
Child Lock..........................................................	22
Set PIN..............................................................	22
Configuring Picture Settings..................................	23
Configuring Picture Settings..............................	23
Picture Mode.....................................................	23
Contrast.............................................................	23
Brightness.........................................................	23
Sharpness.........................................................	23
Colour................................................................	23
Power Save Mode.............................................	23
Backlight (optional)............................................	23
Noise Reduction................................................	23
Advanced Settings........................................	23
Reset.................................................................	24
Changing Picture Format......................................	25
Configuring PC Picture Settings............................	26
PC Picture Settings (*)......................................	26
PC Position........................................................	26
Autoposition.......................................................	26
H Position..........................................................	26
V Position..........................................................	26
Dot Clock...........................................................	26
Phase................................................................	26
Configuring Sound Settings..................................	27
Configuring Sound Settings...............................	27
Operating Sound Settings Menu Items.............	27
Volume..............................................................	27
Equalizer (Only for speaker)..............................	27
Balance (Only for speaker)................................	27
Headphone........................................................	27
Sound Mode......................................................	27
AVL....................................................................	27
Dynamic Bass...................................................	27
Surround Sound................................................	27
Digital Out..........................................................	27
Settings Menu Operation, Conditional Access......	28
Configuring Your TV’s Settings..........................	28
Viewing Settings Menu......................................	28
Conditional Access............................................	28
Language..........................................................	28
Parental.............................................................	28

English - 2 -

Timers...............................................................	28
Date/Time..........................................................	28
Sources.............................................................	28
Other Settings...................................................	28
Using a Conditional Access Module..................	28
Setting Timers, Setting Date/Time........................	29
Timers...............................................................	29
Setting Sleep Timer...........................................	29
Setting Programme Timers................................	29
Configuring Date/Time Settings........................	29
Source Settings, Other Controls...........................	30
Configuring Source Settings..............................	30
Input Selection...................................................	30
Configuring Other Settings - General................	30
Operation...........................................................	30
Menu Timeout....................................................	30
Scan Encrypted Channels ................................	30
Blue Background...............................................	31
Software Upgrade.............................................	31
Application Version............................................	31
Hard of Hearing.................................................	31
Audio Description..............................................	31
Auto TV Off........................................................	31
Broadcast Type (optional).................................	31
Standby Search (*) ...........................................	31
Store Mode........................................................	31
Power Up Mode.................................................	31
DVD Mode.............................................................	32
Handling Discs..................................................	32
Cleaning Discs..................................................	32
DVD - Features................................................	32
DVD - Control buttons on the TV.......................	33
How to watch a DVD.............................................	35
Notes on DVD Playback....................................	35
DVD Mode Configuration..................................	36
TV Type.........................................................	36
Language Setup............................................	36
OSD LANG....................................................	36
AUDIO...........................................................	36
DISC MENU..................................................	36
SUBTITLE.....................................................	36
DEFAULT.......................................................	36
DOWNMIX.....................................................	36
SURROUND..................................................	36
STEREO........................................................	36
PARENTAL....................................................	36
PASSWORD..................................................	36
SPDIF OUTPUT............................................	36
The DVD picture quality is poor.........................	37
Appendix A: DVD Mode Supported file formats....	38
Appendix B: Compatible disc types.......................	38
USB Media Browser..............................................	39
Manual Start......................................................	39
Auto Start..........................................................	39
Playing MP3 Files..............................................	40
Viewing JPEG Files...........................................	40
Slideshow Feature.............................................	41
	English

Video Playback..................................................	41
Media Browser Settings....................................	42
Using MENU button in Media Browser Mode....	42
To Close the Media Player................................	42
Analogue Only Text Services................................	43
Using Text Button -TXT.....................................	43
Accessing Sub-pages........................................	43
Revealing Concealed Text.................................	43
Holding a Page..................................................	43
To display an initial page...................................	43
Appendix C: PC Input Typical Display Modes.......	44
Appendix D: AV and HDMI Signal Compatibility
(Input Signal Types)..............................................	45
Appendix E: PIN Information ................................	46
Appendix F: Supported File Formats for USB
Mode.....................................................................	47
Specifications and Accessories.............................	48
License Information...............................................	49
Q & A Section........................................................	50

- 3 -

English

Safety Precautions

This equipment has been designed and manufactured to meet international safety standards but, like any electrical equipment, care must be taken to obtain the best results and for safety to be assured. Please read the points below for your own safety. They are of a general nature, intended to help with all electronic consumer products and some points may not apply to the goods you have just purchased.

Air Circulation

Leave more than 10cm around all edges when wall mounting the television to allow adequate ventilation. This will prevent overheating and possible damage to the television. Dusty places should also be avoided.

Heat Damage

Damage may occur if the television is left in direct sunlight or near a heater. Avoid places subject to extremely high temperatures or humidity, or locations where the temperature is likely to fall below 5°C (41°F).

Mains Supply

The set should be operated only from a 220-240 V AC 50 Hz outlet. DO ensure that the television is not standing on the mains lead. DO NOT cut off the mains plug from this equipment, this incorporates a special Radio Interference Filter, the removal of which will impair its performance. In the UK, the fuse fitted in this plug is approved byASTAor BSI to BS1362.

It should only be replaced by a correctly rated and approved type. IF IN DOUBT PLEASE CONSULT A COMPETENT ELECTRICIAN.

Warning

To prevent the spread of fire, keep candles or other open flames away from this product at all times.

DO read the operating instructions before you attempt to use the equipment.

DO ensure that all electrical connections (including the mains plug, extension leads and interconnections between pieces of equipment) are properly made and in accordance with the manufacturers’ instructions. Switch off and withdraw the mains plug before making or changing connections.

DO consult your dealer if you are ever in doubt about the installation, operation or safety of your equipment.

DO be careful with glass panels or doors on equipment.

Do not

DON’T remove any fixed cover as this may expose dangerous voltages.

DON’T obstruct the ventilation openings of the equipment with items such as newspapers, tablecloths, curtains, etc. Overheating will cause damage and shorten the life of the equipment.

DON’T allow electrical equipment to be exposed to dripping or splashing or objects filled with liquids, such as vases, to be placed on the equipment.

DON’T place hot objects or naked flame sources, such as lighted candles or nightlights on, or close to equipment. High temperatures can melt plastic and lead to fires.

DON’T use makeshift stands and NEVER fix with wood screws. Use only the manufacturers supplied screws.

DON’T leave equipment switched on when it is unattended, unless it is specifically stated that it is designed for unattended operation or has a standby mode. Switch off by withdrawing the plug, make sure your family know how to do this. Special arrangements may need to be made for people with disabilities.

DON’T continue to operate the equipment if you are in any doubt about it working normally, or it is damaged in any way - switch off, withdraw the mains plug and consult your dealer.

WARNING - excessive sound pressure from earphones or headphones can cause hearing loss.

ABOVE ALL - NEVER let anyone, especially children, push or hit the screen, push anything into holes, slots or any other openings in the case.

NEVER guess or take chances with electrical equipment of any kind - it is better to be safe than sorry.

THE MAINS PLUG IS USED AS A DISCONNECTING DEVICE AND THEREFORE SHOULD BE READILY OPERABLE.

Note : Interactive video games that involve shooting a “gun” type of joystick at the on-screen target may not work with this TV.

English - 4 -

Installation and Important Information

Where to install

Sturdy tie

(as short

as possible)

“P”Clip position on TV is dependent on model.

English

* Button and stand style is dependent on model.

Locate the television away from direct sunlight and strong lights. Soft, indirect lighting is recommended for comfortable viewing. Use curtains or blinds to prevent direct sunlight falling on the screen.

Place the TV on a stable, level surface that can support the weight of the TV. In order to maintain stability and prevent it falling over, secure the TV to a wall using a sturdy tie on the back of the stand.

The LCD display panels are manufactured using an extremely high level of precision technology; however, sometimes some parts of the screen may be missing picture elements or have luminous spots. This is not a sign of a malfunction. Make sure the television is located in a position where it cannot be pushed or hit by objects, as pressure will break

or damage the screen. Also, please be certain that small items cannot be inserted into slots or openings in the case.

Avoid using chemicals (such as air refreshers, cleaning agents, etc.) on or near the TV pedestal. Studies indicate that plastics may weaken and crack over time from the combination effects of chemical agents and mechanical

stress (such as weight of TV). Failure to follow these instructions could result in serious injury and/or permanent damage to TV and TV pedestal.

Cleaning the screen and cabinet…

Turn off the power, and clean the screen and cabinet with a soft, dry cloth. We recommend that you do not use any proprietary polishes or solvents on the screen or cabinet as this may cause damage.

Please take note

The digital reception function of this television is only effective in the countries listed in the “Country” section during the first time installation menu. Depending on country/area, some of this television’s functions may not be available. Reception of future additional or modified services cannot be guaranteed with this television.

Ifstationaryimagesgeneratedby4:3broadcasts,textservices,channelidentificationlogos,computerdisplays, video games, on screen menus, etc. are left on the television screen for any length of time, they could become conspicuous. It is always advisable to reduce both the brightness and contrast settings.

Very long, continuous use of the 4:3 picture on a 16:9 screen may result in some retention of the image at the 4:3 outlines. This is not a defect of the LCD TV and is not covered under the manufacturer’s warranty.

Regular use of other size modes will prevent permanent retention.

EXCLUSION CLAUSE

Toshiba shall under no circumstances be liable for loss and/or damage to the product caused by:

i)fire;

ii)earthquake;

iii)accidental damage;

iv)intentional misuse of the product;

v)use of the product in improper conditions;

vi)loss and/or damage caused to the product whilst in the possession of a third party;

vii)any damage or loss caused as a result of the owner’s failure and/or neglect to follow the instructions set out in the owner’s manual;

viii)any loss or damage caused directly as a result of misuse or malfunction of the product when used simultaneously with associated equipment;

Furthermore, under no circumstances shall Toshiba be liable for any consequential loss and/or damage including but not limited to the following, loss of profit, interruption of business, the loss of recorded data whether caused during normal operation or misuse of the product.

English - 5 -

Important safety information

	English	• Any function related to the digital television (with the DVB logo) is available only within the country or area
		where such signals are transmitted. Verify with the salesperson if it is possible to receive a DVB - T/C signal
		in the area where you live.
		in the area where you live.
		• Even if the television conforms to the required DVB - T/C specifications, the compatibility with future digital
		DVB - T/C transmissions is not guaranteed.
		• Some digital television functions may not be available in certain countries.
		• The DVB - T/C system present in this device, allows reception of both FTA (Free To Air) and Encrypted
		channels.
		Note; Encrypted channels require a specific encryption system to view, which may not be available in certain
		countries.
		• DVB is a registered trademark of the DVB Project. This logo indicates that the product is compliant with
		European Digital Broadcasting.

IMPORTANT INFORMATION

TV Installation

• Do not stand the televisions on cloth or other materials placed between the television and supporting furniture.

• Educating children about the dangers of climbing on furniture to reach the television or its controls.

• Always hold the plug when disconnecting the unit from the socket outlet. Do not pull on flex. The flex can become damaged and cause a short circuit.

• Use a soft, dry cloth to clean the unit.

• Set up unit so that no one will trip over the flex.

• If you intend to wall mount the unit, contact the shop where you purchased the unit for advice, and leave the installation work to professionals. Improper installation can cause damage and/or injuries.

• To protect the unit during a thunder storm, unplug the AC power cord and disconnect the aerial, cable and satellite decoder/systems etc.

Caution: Do not touch the aerial.

• The unit becomes warm when in operation. Do not place any covers or blankets on the unit in order to prevent overheating.

The ventilation holes should not be blocked. Do not set up near radiators. Do not place in direct sunshine.

• Moisture condensation occurs in the following situations:

- When you move the unit from a cold place to a warm place.

- When you use the unit in a room where the heater was just turned on.

- When you use the unit in an area where cold air from an air conditioner directly hits the unit. - When you use the unit in a humid place.

• Never use the unit when moisture condensation could occur.

• Using the unit when moisture condensation exists may damage its own internal parts. After two or three hours, the unit will warm up and moisture will be evaporated.

English - 6 -

Removing the pedestal stand

When using a Wall Bracket

Please use a wall bracket appropriate for the size and weight of the LCD TV.

•Two people are required for installation.

•To install a wall-mount from another manufacturer.

(1)Unplug and remove any cables and/or other component connectors from the rear of the TV.

(2)Carefully lay the front of the unit face down on a flat, cushioned surface such as a quilt or blanket.

(3)Follow the instructions provided with your wall bracket. Before proceeding, make sure the appropriate bracket(s) are attached to the wall and the back of the TV as described in the instructions provided with the wall bracket.

(4)Always use the screws supplied or recommended by the wall mount manufacturer.

Note :

• The bracket shown above is a sample image. The bracket and fixings are not supplied with the TV.

Removing the pedestal stand

(1)Carefullylaythefrontoftheunitfacedownonaflat,cushionedsurfacewiththestandhangingovertheedge.

(2)Remove the screws.

(3)After the screws are removed, hold the pedestal stand in place,then remove the pedestal stand and the plastic moulding from the TV by removing away from the TV.

NOTE: Extreme care should always be used when removing the pedestal stand to avoid damage to the LCD panel.

English

For 32D1333DB and 32D1334DB models

English - 7 -

English

The Remote Control (TV - DVD)

Simple at-a-glance reference of your remote control.

1. Standby	19. Green button
Standby	Repeat

		2.		Image size
		2.		Image size
SLEEP SCREEN PRESETS		3.		Sleep Timer
SLEEP SCREEN PRESETS		4.		Mono/Stereo - Dual I-II / Current
		4.		Mono/Stereo - Dual I-II / Current
	LANG.			Language
				(in DVB channels)
				Language selection (Set
				language)
		5.		No function
			6.	Numeric buttons
		7.		Numeric buttons
	SOURCE	7.		Electronic programme guide(in
				DVB channels)
				DVB channels)

		8.	No function
		9.	Media Browser
			Angle
		10.	Navigation buttons
C	MODE		(Up/Down/Left/Right)
DISP.	MODE		Navigation buttons (Up/Down/
	SEARCH
	INFO		Left/Right)
	INFO	11.	No function
CH	V	11.	No function
			Clear
		12.	No function
			Display time / DVD menu
		13.	Programme Down /
			Page up -
			Programme Up / Page down
			Mute
			Mute
		14.	No function
		15.	Pause
			Pause
		16.	Rapid reverse
			Rapid reverse
		17.	Play
			Play
		18.	Red button
			Zoom

20.Picture mode selection

21.No function

22.Teletext / Mix (in TXT mode)

23.Subtitle on-off (in DVB channels)

Subtitle

24.Previous programme

25.AV / Source selection

AV / Source selection

26.Menu on-off

27.Okay (Confirm) / Hold (in TXT mode) / Channel List

28.Exit / Return / Index page (in TXT mode)

Return

29.No function

Search Mode

30.Info / Reveal (in TXT mode)

Info

31.Volume Up / Down

Volume Up / Down

32.No function

Skip Previous

33.No function

Skip Next

34.Rapid advance

Rapid advance

35.Stop

Stop

36.Blue button

Title

37.Yellow button

Root

Note: The references in Bold are when in DVD mode.

Inserting Batteries and Effective Range of the Remote Control

Remove the back cover to reveal the battery compartment and make sure the batteries are inserted the right way round. Suitable battery types for this remote are AAA, IEC R03 1.5V.

Do not combine a used, old battery with a new one or mix battery types. Remove exhausted batteries immediately to prevent acid from leaking into the battery compartment. Dispose of them in a designated disposal area.

Warning: Batteries must not be exposed toexcessiveheat such as sunshine, fire or the like.

The performance of the remote control will deteriorate beyond a distance of five metres or outside an angle of 30 degrees from the IR receiver. If the operating range becomes reduced the batteries may need replacing.

English - 8 -

Connecting External Equipment

Before connecting any external equipment, remove the mains plug from the wall socket.

DIGITALAUDIO

Socket

* a decoder could be Digital

Satellite, Free to Air or any other compatible decoder.

decoder*

1IMD H

2IMD H

Side View

COMMON INTERFACE

The Common Interface is for a Conditional Access Module (CAM).

	USB Input
HDMI Input	Max:500mA
Sockets	5Vdc
Sockets

	RGB/PC
SPDIF	Input
	Aerial
Coax.OUT	Input
Coax.OUT

5Vdc

Max:500mA

YPbPr SIDE AV

USB Input

SIDE AV

Headphone

YPbPr

SCART

Socket

Aerial cable:...........................................................

Connect the aerial to the ANT. socket on the rear of the TV.

SCART lead:..........................................................

If you use a decoder* or a media recorder, it is essential that the scart cable is connected to the TV.

Before running first time installation, any connected devices need to be set to standby mode.

The DIGITAL AUDIO socket enables the connection of a suitable surround sound system.

HDMI® (High-Definition Multimedia Interface) is for using with a DVD decoder or other equipment with digital audio and video output. It is designed for best performance with 1080i and 1080p high-definition video signals but will also accept and display VGA, 480i, 480p, 576i, 576p and 720p signals. PC format signals will also be displayed.

NOTE:AlthoughthisTVisabletoconnecttoHDMIequipment, it is possible that some equipment may not operate correctly.

When connecting a device via the Side AV input, you must use the supplied connection cable to enable connection.

When connecting a device viaYPbPr input, you must use the supplied connection cable to enable connection.

A wide variety of external equipment can be connected to the TV; therefore, the relevant owner’s manuals for all additional equipment must be referred to for exact instructions.

If the TV automatically switches over to monitor external equipment, return to normal TV by pressing the desired programme position button. To recall external equipment, press SOURCE button repeatedly to switch between sources.

Regardless of source’s property, audio output from the

DIGITAL AUDIO socket cannot be copied.from the DIGITAL AUDIO socket cannot be copied.

English

English - 9 -

Connecting an HDMI® or DVI Device to the HDMI Input

English

The HDMI inputs on your TV receive digital audio and uncompressed digital video from an HDMI source device or uncompressed digital video from a DVI (Digital Visual Interface) source device.

These inputs are designed to accept HDCP (High-Bandwidth Digital-Content Protection) programme material in digital form from EIA/CEA-861-D–compliant [1] consumer electronic devices (such as a set-top box or DVD player with HDMI or DVI output).

NOTE:

•Some early HDMI equipment may not work properly with your latest HDMI TV.

•Supported Audio format: Linear PCM, sampling rate

32/44.1/48kHz.

To Connect an HDMI Device

Connect an HDMI cable (type A connector) to the HDMI terminal. For proper operation, it is recommended that you use an HDMI cable with the HDMI Logo ( ).

•If your HDMI connection is capable of 1080p and/or your TV is capable of refresh rates greater than 50Hz, you will need a Category 2 cable. Conventional HDMI/DVI cable may not work properly with this mode.

•HDMI cable transfers both video and audio. Separate analogue audio cables are not required (see illustration).

•To view the HDMI device video, press SOURCE button to select HDMI1 or HDMI2.

1IMD H

2IMD H

HDMI Input Socket (Back)

To Connect a DVI Device

Connect an HDMI-to-DVI cable (HDMI type A connector) to the HDMI input socket and audio cables to the RED and WHITE SIDE AV AUDIO inputs on the Audio/Video connection cable supplied (see illustration).

•The maximum HDMI-to-DVI cable length is 6.6 ft (2m).

•An HDMI-to-DVI cable transfers video only. Separate analogue audio cables are required.

NOTE:

To ensure that the HDMI or DVI device is reset properly, it is recommended that you follow these procedures:

•When turning on your electronic components, turn on the TV first, and then the HDMI or DVI device.

•When turning off your electronic components, turn off the HDMI or DVI device first, and then the TV.

HDMI device

English - 10 -

Connecting a Computer

To Connect a Computer

With either an RGB/PC or an HDMI connection, you can watch your computer’s display on the TV and hear the sound from the TV’s speakers.

When connecting a PC to the RGB/PC input on TV, use an analogue RGB (15-pin) computer cable and use the SIDE AV socket with a PC audio cable (not supplied) for audio connection, using the supplied Side AV connection cable’s

RED and WHITE inputs (see illustration).

	PC	VGA Cable
	(not	supplied)
RGB/PC	Input	or
(back)		or
	Side Audio/Video
	Connection	Cable
	(supplied)
SIDE AV		PC Audio Cable
SIDE AV	Input	(not supplied)
SIDE AV	Input

To use a PC, set the monitor output resolution on the PC before connecting it to the TV. To display the optimum picture, use the PC setting feature.

NOTE:

•Some PC models cannot be connected to this TV.

An adaptor is not needed for computers with a compatible mini D-sub15-pin terminal.

•Depending on the DVD’s title and the specifications of the PC on which you are playing the DVD-Video, some scenes may be skipped or you may not be

able to pause during multiangle scenes.

English

Connecting to a DVD Player via YPbPr

Some DVD players are connected through

COMPONENT SOCKETS (YPbPr). In this case, you must use the supplied Component YPbPr video connection cable for enabling connection. First, plug the single jack of the cable to the TV’s YPbPr socket (side). Afterwards, insert your YPbPr cable’s (not supplied) connectors into the plural part of the supplied

YPbPrvideoconnectioncable(seeillustrationbelow).

Colours of the connected jacks should match.

To enable audio connection, use the supplied Side AV connection cable. First, plug single jack of the cable to the Side AV Input of the TV. Afterwards, insert your

DVD player’s audio cable’s connectors into the plural part of the supplied Side AV connection cable (see illustration below). Colours of the connected jacks should match.

Video Connection

(supplied)

Audio	Connection
				DVD Player
	V		To RED	& WHITE inputs
	A
	de
	i
	S
Side AV	Input	Side AV	Audio	Cable
		Side AV	Audio	Cable
		Connection cable	(Not	supplied)
		(supplied)

Connecting a USB Memory

To Connect a USB Flash Drive

•You can connect a USB Flash Drive to your TV by using the USB input of the TV. This feature allows you to display/play music, photo or video files stored in a USB stick.

•It is possible that certain types of USB devices (e.g. MP3 Players) may not be compatible with this TV.

•You may back up your files before making any connections to the TV set in order to avoid any possible data loss. Note that manufacturer will not be responsible for any file damage or data loss.

•Do not pull out USB module while playing a file.

CAUTION: Quickly plugging and unplugging USB devices may cause damage to the USB device.

English - 11 -

Power Save Mode

English

Environmental Information

This television is designed to consume less energy to save environment. You not only help to save the environment but also you can save money by reducing electricity bills thanks to the energy efficiency feauture of this TV. To reduce energy consumption, you should take the following steps:

You can use Power Save Mode setting, located in the Picture Settings menu. If you set Power Save Mode as

Eco, the TV will switch to energy-saving mode and luminance level of TV set will be decreased to optimum level. Note that some picture settings will be unavailable to be changed when the TV is in Power Save Mode.

If Picture Off is selected, “Screen will be off in 3 seconds.” message will be displayed on the screen. Select PROCEED and press OK to continue. The screen will be off in 15 seconds. If you disable Power Save Mode,

Picture mode will be automatically set to Dynamic.

When the TV is not in use, please switch off or disconnect the TV from the mains plug. This will also reduce energy consumption.

Disconnect power when going away for longer time.

It is highly recommended to activate Power Save Mode setting to reduce your annual power consumption. And also it is recommended to disconnect the TV from the mains plug to save energy more when you do not use.

Please helps us to save environment by following these steps.

Repair Information

Please refer all servicing to qualified personnel. Only qualified personnel must repair the TV. Please contact your local dealer, where you have purchased this TV for further information.

English - 12 -

Controlling the TV

A wide variety of external equipment can be connected via the sockets located on the side and back of the

TV. Whilst all the necessary adjustments and controls for the TV are made using the remote control, the buttons on the Back of the TV may be used for some functions.

English

Switching on

If the standby LED is unlit, check that the mains plug is con-

nected to the power and press the / I button on the back side of the television to switch the television on.

To put the television into Standby, press button on the remote control or on the TV. To view the television, press button again. The picture may take a few seconds to appear.

Note: The active Standby LED colour will turn to red in a few moments when the TV is switched Standby.

For energy saving:

Turning the TV off at its mains supply, or un-plugging it, will cut energy use to nearly zero for all TV’s. This is recommended when the TV is not being used for a long time, e.g. when on holiday.

Reducing the brightness of the screen will reduce energy use. Energy efficiency cuts energy consumption and thus saves money.

NOTE: Putting the TV into standby mode, will reduce energy consumption, but will still draw some power.

Using the Remote Control

Press the MENU button on the remote control to see the menus.

The main menu appears as a group of icons each for a menu option. Press the Left or Right button to select a topic.

In sub menu screen mode the menu appears as a list. Press the Up or Down button to select a topic.

To use the options press the Up and Down buttons on the remote control to move up and down through them and OK, Left or Right buttons to select the required choice. Follow the on screen instructions. The functions of each menu are described in detail throughout the manual.

Using the Controls on the TV

Using the control buttons on the Back of the TV:

• To alter the volume press + or - .

• To alter the programme position press	P	on the
Back of the TV.

• Press + - buttons at the same to view main menu and use P to navigate and + - to change value.

To select an external input, press until the appropriate input source is selected.

Please always refer to the owner’s manual of the equipment to be connected for full details..

English - 13 -

English

Initial Installation

Before switching on the TV, put your decoder and media recorder to Standby if they are connected and ensure the aerial is connected to your TV. To set up the TV, use the buttons on the remote control as detailed on page 8.

IMPORTANT: Ensure that the aerial is connected and a Common Interface module is not inserted before switching on the TV for the first time installation.

1.Connect the mains plug and switch the TV to

on on using the / I button. If the TV does not switch on, press any numbered or button on the remote control, then the language selection menu will be displayed. This screen will appear the first time that the TV is switched on and each time the TV is reset.

2.By pressing Up or Down button, highlight the language you want to set and press OK button.

The following message will be displayed next:

3.By pressing Left or Right button, select the country you want to set and press Down button to highlight the Search Type option. Use Left or Right to set the desired search type. Available search types are digital only, analog TV only and full.

4.When set, Down button to select Teletext

Language. Use Left or Right button to select desired Teletext Language.

English

5.Press OK button on the remote control to continue and the following message will be displayed on the screen:

6.Select Yes button by using Left or Right button and press OK button to continue. Afterwards, the following OSD will be displayed on the screen:

7.If you select Cable option, the following screen will be displayed:

Note: Although this cable feature can be selected, it is not fully supported in the UK. If cable signals are input to this TV from a Cable Network Provider some may be displayed.

8.You can select frequency ranges from this screen. For highlighting lines you see, use Up or

Down button. You can enter the frequency range manually by using the numeric buttons on the remote control. Set Start and Stop Frequency as desired by using numeric buttons on the remote control. After this operation, you can set Search

Step as 8000 kHz or 1000 kHz. If you select

1000 kHz, the TV will perform search process in a detailed way. Searching duration will thus increase accordingly. When finished, press OK button to start automatic search.

- 14 -

Initial Installation - continued

Auto Tuning

9.If you select Aerial option from the Search Type screen, the television will search for broadcasts.

10.The Auto tuning screen will appear and the television will start to search for available stations.

The progress bar will move along the line. You must allow the television to complete the search.

The following OSD will be displayed on the screen and the television will search for the selected broadcasts:

Note: You can press MENU button to cancel.

After the available stations are stored, Channel List will be displayed on the screen.

• Press OK button to quit channel list and watch TV.

Note:

Do not turn off the TV while initializing first time installation.

Keep the menu of Store Mode Disabled and do not change it, when using at home.

•Press the Left or Right button to choose the required language region.

•After the Teletext language is selected, press MENU button to exit.

English

Auto Tuning

As new services are broadcast, it will be necessary to retune the television in order to view them.

•Auto Tuning will completely retune the television and can be used to update the channel list. It is recommended that Auto Tuning is run periodically to ensure that all new services are added. All current channels and settings, i.e. locked channels, will be lost.

•Press MENU button on the remote control and select

Install and Retune by using Left or Right button.

Press OK button and the following menu screen will be displayed.

•Select Automatic Channel Scan (Retune) by using

Up or Down button and press OK button. Automatic

ChannelScanoptionswillbedisplayed.Youcanselect options by using Up or Down and OK buttons.

Auto Channel Scan Menu Operation

Digital: Searches and stores aerial DVB stations. Analogue: Searches and stores analogue stations.

Full: Searches and stores both analogue and aerial

DVB stationsres both analogue and cable DVB stations.

•Whenever you select an automatic search type and press OK button, a confirmation screen will appear on the screen. To start installation process, select

Yes, to cancel select No by using Left or Right and OK button.

•After auto channel scan type is set and selected and confirmed, installation process will start and progress bar will move along. Press MENU button to cancel process. In such a case, located channels are not stored. The television will start to search for all available stations. You must allow the television to complete the search.

English - 15 -

+ 37 hidden pages