Toshiba B-EP4DL User Manual

5 (1)
TOSHIBA Portable Printer
B-EP2D/EP4D SERIES
Owner's Manual
[B-EP2DL]
CE Compliance (for EU only)
This product complies with the requirements of EMC, Low Voltage and R&TTE Directives including their
amendments.
FCC Notice
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one
or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
“This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment
Regulations. ”
“Cet appareil numérique de la classe B respecte toutes les exigences du Règlement sur lematériel brouilleur
du Canada.” (for CANADA only)
V
ORSICHT:
Maschinenlärminformations-Verordnung 3. GPSGV, der höchste Schalldruckpegel beträgt 70 dB(A) oder
weniger gemäß EN ISO 7779.
Some types of this product are equipped with a wireless communication device, such as, TEC-BTM-R and SD-
Link 11g. Please be sure to read the enclosed Precautions for Handling of Wireless Communication Devices
before using this product.
CAUTION
1. Only use TOSHIBA TEC battery packs designed and manufactured for use with the specific printer model.
There is a risk of explosion if the battery is replaced by an incorrect type. Dispose of used batteries
according to the instructions.
B-EP2DL-GH20-QM-R B-EP4DL-GH20-QM-R
B-EP2DL-GH30-QM-R B-EP802-BT-QM-R B-EP4DL-GH30-QM-R B-EP804-BT-QM-R
B-EP2DL-GH40-QM-R B-EP4DL-GH40-QM-R
2. When an external power source such as an AC adapter is connected to the printer, DO NOT use any device
other than an exclusive one.
AC adapter: B-EP800-AC-QM-R (Model: 0225A1950)
Cigarette lighter adapter: B-EP802-DC12-QM-R
DC adapter: B-EP800-DC48-QM-R
N258
Copyright © 2008
by TOSHIBA TEC CORPORATION
All Rights Reserved
570 Ohito, Izunokuni-shi, Shizuoka-ken, JAPAN
< For EU Only >
TOSHIBA TEC Europe Retail Information Systems S.A.
Rue de la Célidée 33 BE-1080 Brussels
E
PRINTED IN JAPAN
EO1-33079
The following information is for EU-member states only:
Disposal of batteries and/or accumulators
(based on EU-Directive 2006/66/EC,
Directive on batteries and accumulators and waste batteries and accumulators)
The use of the symbol indicates that batteries and/or accumulators may not be disposed as
unsorted municipal waste and has to be collected separately.
By ensuring that batteries and/or accumulators are disposed of correctly, you will help preven
t
potential negative consequences for the environmental and human health, which could
otherwise be caused by inappropriate waste handling of this product.
For more detailed information about the take-back and recycling of batteries and/o
r
accumulators, please contact your supplier where you purchased this product.
Precautions for Handling of Wireless Communication Devices
Bluetooth® Module: TEC-BTM-R (GH30 model)
Wireless LAN Module: SD-Link 11g (GH40 model)
Trade Mark
Bluetooth is a registered trademark owned by Bluetooth SIG, Inc. and used byTOSHIBA TEC CORPORATION under
license.
Cautions
General
For all countries and areas
This product is a wireless communication device, and the use of thisproduct is restricted to the following countries or
areas. If the product isused in the countries or areas other than the following, you may bepunished according to the
laws of those countries or areas.
Japan, USA, Canada, Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,
Germany, Greece, Hungary, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, United Kingdom, Switzerland, Norway, Iceland, Liechtenstein,
Australia, New Zealand, Mexico, China, Korea, Taiwan
For Europe
for Bluetooth for wireless LAN
Hereby, TOSHIBA TEC CORPORATION, declares that the TEC-BTM-R and SD-Link11g are in compliance with the
essential requirements and other relevant provisions of Directive 1999/5/EC. This equipment uses a radio frequency
band that has not been harmonized throughout all EU and EFTA countries, and can be used in the following countries.
Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Poland, Portugal, Romania, Slovakia, Slovenia,
Spain, Sweden, United Kingdom, Switzerland, Norway, Iceland, Liechtenstein
For USA
This device complies with Part 15 of the FCC Rules.Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, includinginterference that may cause undesired operation.
Changes or modification not expressly approved by manufacturer forcompliance could void the user’s authority to
operate the equipment.
For Canada
Operation is subject to the following two conditions:
(1) this device may not cause interference, and
(2) this device must accept any interference, including interference that may cause undesired operation of the device.
To prevent radio interference to the licensed service, this device is intended to be operated indoors and away from
windows to provide maximum shielding. Equipment that is installed outdoors is subject to licensing.
For safety
Do not use this product in locations where use may be forbidden, for example,in an aeroplane or a hospital. If you do
not know the forbidden areas, please referto and follow the airline company or medical institution guidelines.
Flight instrument or medical equipment may be affected, causing a serious accident.
Since this product uses extremely low power compared with mobile phones, itcannot possibly interfere the
pacemakers and defibrillators. However, if the useof this product should be likely to have affected the pacemaker or
defibrillator,immediately stop using the product and contact your TOSHIBA TEC sales agent.
Do not disassemble, modify, or repair the product. Doing so may cause injury. Also, modification is against the Laws
and Regulations for Radio Equipment. Please ask your TOSHIBA TEC sales agent for repair.
Precaution in use
This product communicates with other devices by radio. Depending on the installation location, orientation,
environment, etc., its communication performance may deteriorate or devices installed near by may be affected.
Keep away from a microwave.
Communication performance may deteriorate or a communication error may occur due to the radio emitted from a
microwave.
Since the Bluetooth and wireless LAN use the same radio frequency band, each radio wave may interfere with each
other when they are used at the same time, causing a deterioration of communication performance or a disconnection
of network. If there is any problem with connection, please stop using either Bluetooth or wireless LAN.
Do not use the product on a metal table or near a metal object.
Communication performance may be deteriorated.
TEC-BTM-R Specification
Bluetooth class 2
Built-in protocol stack activated by Bluetooth V1.2 serial port profile
Operating temperature: -5 to 50°C 25% to 85%RH (No condensation)
Dimensions: 38.1 mm (W) x 25.4 mm (H) x 7 mm (D)
SD-Link 11g Specification
Built-in IEEE802 Part 11b/g (802.11b/g)
Operating temperature: 0 to 50°C 25% to 85%RH (No condensation)
Dimensions: 67.8 mm (W) x 36.8 mm (H) x 7.5 mm (D)
Changes or modifications not expressly approved by manufacturer for compliance could void the user's
authority to operate the equipment.
CAUTION!
1.To avoid injury, be careful not to catch or jam your fingers while opening or closing the cover.
2.Do not touch moving parts. To reduce the risk that fingers, jewellery, clothing, etc., be drawn into the moving
parts, turn off the power switch to stop movement.
Safety Summar
y
Personal safety in handling or maintaining the equipment is extremely important. Warnings and Cautions
necessary for safe handling are included in this manual. All warnings and cautions contained in this manual
and written inside or outside of the printer should be read and understood before handling or maintaining the
equipment.
Do not attempt to effect repairs to this equipment. If a fault occurs that cannot be rectified using the
procedures described in this manual, turn off the power, then contact your authorised TOSHIBA TEC
representative for assistance.
Safety Precautions
This Owner's Manual and the products (machines) which you have purchased contain indications which should
be observed in order to use the machines safely and prevent harm to yourself and others and damage to
property. The meanings of these indications and symbols are given below.
Read these indications and become familiar with their contents before reading this Owner's Manual.
Precautions
The following precautions will help to ensure that this machine will continue to function correctly.
(1) Try to avoid locations that have the following adverse conditions:
*Temperatures below -5°C and above 40°C
*Humidity below 10%RH and above 90%RH
*Direct sunlight
*Excessive vibration
(2) The cover should be cleaned by wiping with a dry cloth or a cloth slightly dampened with a mild detergent
solution. NEVER USETHINNER OR ANY OTHER VOLATILE SOLVENT on the plastic covers.
(3) USE ONLY TOSHIBA TEC SPECIFIED media.
(4) DO NOT STORE the media where it might be exposed to direct sunlight, high temperatures, high humidity,
dust, or gas.
(5) Any data stored in the memory of the printer could be lost during a printer fault.
(6) DO NOT open the media cover and battery cover during operation. Doing so will stop printer operation.
(7) DO NOT scratch the surface of printed labels or receipt with a sharp object.
CAUTION
!
1.This manual may not be copied in whole or in part without the prior written permission of TOSHIBA TEC.
2.The contents of this manual may be changed without notification.
3.Please refer to your local Authorised Service representative with regard to any queries you may have in this
manual.
If water or any other liquid enters the machine, turn off the power. Continuous use of the machine under such
conditions may cause fire or electric shock.
If the enclosure is damaged when dropped or subject to shock, turn off the power. Continuous use of the
machine under such conditions may cause fire or electric shock.
Avoid continuous exposure to direct sunlight or high temperature as this may cause fire.
Do not remove covers or modify the machine by yourself. Doing so may cause fire or electric shock.
Avoid water, operation with wet hands or cleaning with a moistened cloth. Failure to do this may cause fire or
electric shock.
Do not wipe the machine with a cloth moistened with thinner or other volatile solvent as this may cause fire or
electric shock.
Use the specified battery only. Failure to do this may cause fire or electric shock.
Danger of explosion if the battery is incorrectly replaced. Replace the battery only with TOSHIBA TEC
Corporation, Battery Pack Model B-EP802-BT-QM-R 7.4V 2600mAh Li-ion or B-EP804-BT-QM-R 14.8V
2600mAh Li-ion. Discard used batteries according to the manufacturer's instruction.
Do not disassemble and modify the battery because it has a protection unit in it. Doing so may break the
protection unit, causing the battery to heat up, burst or burn.
If the battery gets wet, dry it completely. Using a wet battery may cause fire or electric shock.
Be aware of the following precautions when using batteries. Otherwise they could heat up, burst or burn.
Do not throw the battery into fire or heat it with a microwave or oven, etc.
Do not load the battery with the electrodes reversed.
Do not connect the electrodes with metal objects like wire. Do not carry or store the battery along with
metal objects such as necklaces, hairpins, etc.
Do not stick a needle into, hammer, step on, or drop the battery.
Do not solder the battery.
Do not leave the battery where the temperature is more than 60°centigrade, such as inside a car or in
direct sunlight.
Keep away from flame or other sources of heat. Failure to do this may cause fire or machine failure.
Do not drop or shock the machine as this may cause machine failure.
During lightning, turn off and keep away from the machine because of danger of electric shock and machine
failure.
Avoid locations subject to rapid change in temperature as this causes condensation, causing electric shock
or machine failure.
Do not damage the print head, platen or strip roller with a sharp object. Doing so may cause machine failure.
Do not touch or contact the print head element with a metal object. Doing so may cause machine failure.
Use the specified media only. Failure to do this may cause machine failure.
Be sure to turn off the machine before replacing the battery, or machine failure may occur.
Do not charge the battery near flame or under direct sunlight. High temperature may activate or damage the
protection unit of the battery, disabling the electric charge or causing it to overheat, burst, or burn.
Unload the battery when the machine will not be used for a longtime. Failure to do this may cause machine
failure.
Keep the battery away from flame, a heat source or other locations subject to high temperature.
Failure to do this may cause it to over heat or burn.
Use the specified battery charger only. Failure to do this may cause the battery to overheat, burst or burn.
Do not force the battery into the machine or battery charger. Doing so may cause the battery to overheat,
burst or burn. Check for the correct electrode.
Do not connect the battery to a power outlet or a car cigarette lighter jack as this may cause the battery to
overheat, burst or burn.
Because the B-EP802-BT-QM-R and the B-EP804-BT-QM-R Series battery is exclusively for the B-EP2DL
and the B-EP4DL Series printer, respectively, do not use the battery in other machines. Doing so may
damage the battery or affect the performance and life of the battery.
CAUTION
This indicates that there is the risk of personal injury or damage to objects if the machines are
improperly handled contrary to this indication.
WARNING
This indicates that there is the risk of death or serious injury if the machines are handled
improperly or contrary to this indication.
Part Names
B-EP2DL Series
Top Cover
RS-232C Port
(GH20 only)
Peel-off Roller
Platen
IrDA Window
Top Cover Open Button
Operation Panel
Strap Slot
USB Port
Peel-off Roller Cover
DCIN Connector
Battery Lever
Battery Pack
Print Head
Belt Clip
Screws
Print Head Cleaner
Media Guide Roller
Media Sensor
B-EP4DL Series
IrDA Window
Top Cover Open Button
Operation Panel
Strap Slot
Battery Lever
Battery Pack
Top Cover
Peel-off Roller
Platen
Print Head
Peel-off Roller Cover
DCIN Connector
USB Port
Belt Clip
Screws
Print Head Cleaner
Media Guide Roller
Media Sensor
RS-232C Port
(GH20 only)
Operation Panel Functions
No. Name/Icon Function/Usage
Liquid Crystal Display
(16 lines x 2 lines)
Upper line: Icons indicating the printer statuses, such as the radio
intensity, battery level, etc. are displayed.
Lower line: Printer status is indicated in alphanumerals or symbols.
ON LINE
The printer is ready for an issue command from
the host.
PAUSE
The printer is in pause state. When the printer
is paused during printing, the number of
unprinted labels is displayed.
(1)
LCD Message
COVER OPEN The top cover is open.
(2) Radio intensity Indicates the radio intensity in 4 levelsGH40 only
(3) Connection Indicates an access point connection statusGH40 only
(4) Sleep Displayed while the printer is in the power save mode.
(5) Transmission Indicates data transmission status.
(6) Error Displayed when an error occurred on the printer.
(7) External power source Displayed when the printer is charged with an optional device.
(8) Battery level Indicates the battery level in 5 levels.
(9) STATUS lamp
Lights or blinks in green, red, or orange to indicate the printer
status.
Lights up in green: Normal state
Lights up in orange: Near a low-battery state (Operable)
Lights up in red: Low-battery state
Blinks in green or orange: Communicating or internal processing
is in progress or a printed label is waiting to be removed.
Blinks in red: Error state
(10) CHARGE lamp
Blinks in orange while the battery pack is charged. Lights up in
green when the battery charge is completed.
(1)
(2) (3) (4) (6)(5) (7) (8)
(11)
(9)
(10) (12) (13)
Loading...
+ 19 hidden pages