Toshiba 32WLT66A, 42WLT66A, 47WLT66A, 37WLT66A User Manual

OWNER'S MANUAL

Integrated Digital LCDTV

32WLT66A

37WLT66A

42WLT66A

47WLT66A

Owner's Record

You will find the model number and serial number on the back of the TV. Record these numbers in the spaces provided below. Refer to them whenever you call upon your TOSHIBA dealer regarding this product.

Model number:

Serial number:

DVB registration identification reference number: 4165 (32WLT66A), 4073 (37WLT66A), 4074 (42WLT66A), 4075 (47WLT66A). Trade Mark of the DVB Digital Video Broadcasting Project (1991 to 1996).

VX1A000109A0

Contents

Introduction

Welcome to Toshiba. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Important Safety Instructions . . . . . . . . . . . . . . . . . . . . . . 3 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Important information. . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Getting started

Connecting an antenna . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Exploring your new TV . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Installing the remote control batteries . . . . . . . . . . . . 7 TV top and front panel controls . . . . . . . . . . . . . . . . . . . . 8 TV side and back panel connections . . . . . . . . . . . . . . . . 9 Learning about the remote control . . . . . . . . . . . . . . . . . 10 Location of controls . . . . . . . . . . . . . . . . . . . . . . . . . 10 Learning about the menu system . . . . . . . . . . . . . . . . . . 11 Displaying the DIGITAL SETTING chart. . . . . . . . 11 Displaying the TV SETUP menu chart . . . . . . . . . . 11 Turning the TV on . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Switching on the TV . . . . . . . . . . . . . . . . . . . . . . . . 12 Switching off the TV . . . . . . . . . . . . . . . . . . . . . . . . 12

Tuning the TV for the first time

- digital only -. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Programming channels into the TV’s channel

memory. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Auto scan - digital only - . . . . . . . . . . . . . . . . . . . . . 13 Manual scan - digital only - . . . . . . . . . . . . . . . . . . . 14 Programming channels automatically

- analog only - . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Manually setting channels in the channel

memory - analog only - . . . . . . . . . . . . . . . . . . . 15 Watching TV programs . . . . . . . . . . . . . . . . . . . . . . . . . 16 Viewing Digital programs - digital only - . . . . . . . . 16

Selecting channel from Navigation List

- digital only -. . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Changing the program position - analog only - . . . . 16 Switching between two program positions . . . . . . . 16 Selecting the menu language - analog only - . . . . . . 16 Displaying the on-screen information

- analog only - . . . . . . . . . . . . . . . . . . . . . . . . . . 16 On-screen information - digital only - . . . . . . . . . . . 16 Setting the I-Plate -digital only- . . . . . . . . . . . . . . . . 17 Sorting program position -analog only- . . . . . . . . . . 17

Using the TV’s features (General)

Picture adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 Selecting the picture size . . . . . . . . . . . . . . . . . . . . . 18 Using the picture still . . . . . . . . . . . . . . . . . . . . . . . . 19 Adjusting the picture position - analog only - . . . . . 19 Resetting the picture position - analog only - . . . . . 19 Selecting the picture mode . . . . . . . . . . . . . . . . . . . . 19 Adjusting the basic picture quality. . . . . . . . . . . . . . 19 Activating the black stretch . . . . . . . . . . . . . . . . . . . 20 Activating the MPEG NR (Noise Reduction) . . . . . 20 Activating the DNR (Digital Noise Reduction)

- analog only - . . . . . . . . . . . . . . . . . . . . . . . . . . 20 Selecting the color temperature . . . . . . . . . . . . . . . . 20 Adjusting the color management . . . . . . . . . . . . . . . 20 Resetting the base color adjustment . . . . . . . . . . . . . 20 Using the cinema mode - analog only - . . . . . . . . . . 21 Using the auto format. . . . . . . . . . . . . . . . . . . . . . . . 21 Activating the ANT ATT (Antenna Attenuation) . . 21

Sound adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 Setting the MTS (Multi-channel TV Sound)

- analog only - . . . . . . . . . . . . . . . . . . . . . . . . . . 22 Selecting the dual 1 or dual 2 mode

- analog only - . . . . . . . . . . . . . . . . . . . . . . . . . . 22 Selecting the stereo programs - analog only - . . . . . 22 Selecting the bilingual programs - analog only - . . . 22 Adjusting the sound quality . . . . . . . . . . . . . . . . . . . 22 Using the SRS WOW surround sound . . . . . . . . . . . 23 Using the stable sound . . . . . . . . . . . . . . . . . . . . . . . 23 Using the bass boost. . . . . . . . . . . . . . . . . . . . . . . . . 23

Activating blue screen . . . . . . . . . . . . . . . . . . . . . . . . . . 23 Adjusting the brightness of side panel . . . . . . . . . . . 23

The timers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 Setting the Time zone - digital only - . . . . . . . . . . . . 24 Program Timer - digital only - . . . . . . . . . . . . . . . . . 24 Selecting the timer menu - analog only - . . . . . . . . . 25 Selecting the video input source to view. . . . . . . . . . . . . 25 Setting the manual setting menu - analog only -. . . . 25 Teletext in Analog TV. . . . . . . . . . . . . . . . . . . . . . . . . . . 26 Setting up the teletext mode . . . . . . . . . . . . . . . . . . . 26 Teletext general information. . . . . . . . . . . . . . . . . . . 26 Using Auto mode . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 Using LIST mode . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 Teletext buttons on the remote control . . . . . . . . . . . 28 Teletext in Digital TV . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Other Digital TV features and settings

Setting the EPG (Electronic Program guide) . . . . . . . . . 29 Password . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 Setting the password . . . . . . . . . . . . . . . . . . . . . . . . . 29 Parental rate. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 Setting the parental rate. . . . . . . . . . . . . . . . . . . . . . . 30 Channel list . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 Setting favorite, locking and deleting channels . . . . 30 Editing channel names . . . . . . . . . . . . . . . . . . . . . . . 30 Favorite Channel List . . . . . . . . . . . . . . . . . . . . . . . . 31 Favorite Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 Subtitle. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 Information, restore factory setting . . . . . . . . . . . . . . . . . 31 Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 Restore factory setting . . . . . . . . . . . . . . . . . . . . . . . 31 Digital Output, Audio Track . . . . . . . . . . . . . . . . . . . . . . 32 Digital Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 Audio Track . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 Transparency . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 TV Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

Connecting your TV

Back connections. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 Connection example . . . . . . . . . . . . . . . . . . . . . . . . . 33 Connecting an audio system - digital only - . . . . . . . 33 Connecting an amplifier equipped with a Dolby

Digital decoder . . . . . . . . . . . . . . . . . . . . . . . . . . 34 Connecting an amplifier equipped with an MPEG

decoder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 Connecting an amplifier equipped with a digital

audio (optical) input . . . . . . . . . . . . . . . . . . . . . . 34 Side connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 Connection example . . . . . . . . . . . . . . . . . . . . . . . . . 35 Connecting an HDMI or a DVI device . . . . . . . . . . . . . . 35 Connecting an HDMI or a DVI device . . . . . . . . . . . 35 Connecting an HDMI device . . . . . . . . . . . . . . . . . . 36 Connecting a DVI device . . . . . . . . . . . . . . . . . . . . . 36 Selecting the PC/HDMI1 audio mode. . . . . . . . . . . . . . . 36 Setting the HDMI1 audio mode . . . . . . . . . . . . . . . . . . . 36 Connecting a computer . . . . . . . . . . . . . . . . . . . . . . . . . . 37 Using the PC setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38 Adjusting the picture size/position . . . . . . . . . . . . . . 38 Adjusting the clock phase of the picture. . . . . . . . . . 38 Adjusting the sampling clock . . . . . . . . . . . . . . . . . . 38 Resetting the PC setting . . . . . . . . . . . . . . . . . . . . . . 38

Reference section

Troubleshooting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39 Symptom and solution . . . . . . . . . . . . . . . . . . . . . . . 39 Symptom and solution - digital only - . . . . . . . . . . . 39 APPENDIX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

AUSTRALIAN PARENTAL GUIDANCE

CODES (Normative) . . . . . . . . . . . . . . . . . . . . . 40 Broadcast system. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

Broadcast transmission systems of each country or region . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41 Integrated Digital LCD TV . . . . . . . . . . . . . . . . . . . . 41

2

Introduction

Welcome to Toshiba

•Thank you for purchasing this Toshiba LCD Color Television. This manual will help you use the exciting features of your new TV.

•Instructions in this manual are based on using the remote control.

•Please read all safety and operating instructions in this manual carefully, and keep this manual for future reference.

Important Safety Instructions

Be sure to observe the following instructions and precautions to ensure safe use of this TV.

Installation

1)Always connect the power plug to an appropriate electrical outlet equipped with 220-240V, AC 50Hz.

Never use the TV outside the specified voltage range. It may cause a fire or an electric shock.

220-240V AC, 50Hz

Check!

2)Never insert or remove the power plug with wet hands.

This may cause an electric shock.

3)Never place the TV in an unstabilized location such as on a shaky table, incline or location subject to vibration.

The TV may drop or fall off which may cause injury or damage.

4)Never block or cover the slots and openings in the cabinet.

•Never place the TV so that it is facing upward or on its side.

•Never place the TV in a closet, bookcase or other similar area where the ventilation is poor.

•Never drape a newspaper, tablecloth or curtain on the TV.

•When installing the TV against a wall, always keep the TV at least 10 cm away from the wall.

•Never place the TV on a soft unstable surface, such

as a carpet, or a cushion.

The inside of this TV will overheat if the ventilation holes are covered, blocked or sealed, which may result in a fire.

5)Never place the TV near a heater or in direct sunlight.

The surface of the cabinet or power cord may melt and result in a fire or an electric shock.

6)Never place the TV in an area exposed to high humidity levels, such as in a bathroom or close to a humidifier.

This may cause a fire or an electric shock.

7)Never place the TV next to a stove where it will be exposed to oil, smoke, or steam, or in a location where there is a large quantity of dust.

This may cause a fire or an electric shock.

3

Introduction

8)Install the TV in a horizontal, stable location. Connect between two clips on the back of the TV and a wall, pillar, etc., with a sturdy tie and clip of supplied accessories (- page 42).

•Use as short a tie as possible to ensure the TV is stable.

•If the TV is not installed securely, it may lean or fall over and cause an injury.

•To prevent injury, use the exclusive optional stand or wall-hanging bracket to install this TV on the floor or wall securely in accordance with a qualified technician.

Sturdy tie

(as short as possible)

	Clip
Clip	Clip

Side view

Top view

9)Precautions for moving the TV

•When moving the TV, be sure to remove the plug from the wall outlet and disconnect the antenna cable and audio/video cables, any steady ties. Fire or electric shock may result if the power cord is damaged.

•When carrying the TV, at least two people are needed. Be sure to carry it upright.

•Never carry the TV with the screen facing up or down.

Use

1)Never place hot objects or open flame sources, such as lighted candles or nightlights, on or close to the TV.

High temperatures can melt plastic and lead to fires.

2)The apparatus shall not be exposed to dripping or splashing and that no objects filled with liquids, such as vases, shall be placed on the apparatus.

When liquids are spilled or small items are dropped inside the TV, this may cause a fire or an electric shock. If small objects drop inside the TV, turn off the TV and remove the power plug from the outlet immediately and contact a service technician.

3)Never insert objects (metal or paper) or pour water inside the TV through ventilation holes and other openings.

These items may cause a fire or an electric shock.

If these objects are inserted inside the TV, turn off the TV and remove the power plug from the outlet immediately and contact a service technician. Be especially careful that children do not insert objects in the TV.

10)Precautions for installing on outdoor antenna

An outside antenna system should not be located in the vicinity of overhead power lines, or other electric light or power circuits.

If the antenna falls down or drops, it may cause injury or electric shock.

Clip

4)Never stand or climb on the TV.

Be especially careful in households with children to prevent them through climbing on top of the TV.

It may move, fall over, break, become damaged or cause an injury.

4

Introduction

5)When the TV will not be used for a long period of time, such as during vacation or travel, remove the power plug from the wall outlet for safety.

•The TV is not completely disconnected from the power supply line, as minute current is consumed even when the ! Power switch is turned off.

•The Mains plug or an appliance coupler is used as the disconnect device, therefore the disconnect device shall remain readily operable.

6)Never pull on the power cord when removing the plug from the wall outlet.

Always hold the plug firmly when removing it. If the power cord is yanked, the cord may become damaged and a fire or an electric shock may occur.

7)Never cut, break, modify, twist, bunch up or bent the cord or apply excessive force or tension to it.

Never place heavy objects on the cord or allow it to overheat as this may cause damage, a fire or an electric shock. Contact a service technician if the power cord is damaged.

8)If there is thunder or lightning, never touch the antenna cable or other connected cables.

You may suffer an electric shock.

Service

1)Never repair, modify or disassemble the TV by yourself.

It may cause a fire or an electric shock. Consult a service technician for inspection and repairs.

2)When a malfunction occurs, or if smoke or an unusual odor comes from the TV, turn off the TV and remove the power plug from the outlet immediately.

Make sure that the smoke or smell has stopped, then contact a service technician. If the TV is still used in this condition, it may cause a fire or an electric shock.

3)If the TV is dropped or the cabinet is broken, turn off the TV and remove the power plug from the outlet immediately.

If the TV is still power used in this condition, it may cause a fire or an electric shock. If the cabinet is broken, be careful when handling the TV to prevent an injury. Contact a service technician for inspection and repair.

4)When the TV reaches the end of its useful life, ask a qualified service technician to properly dispose of the TV.

Note:

The lamp unit contains a small amount of mercury. Disposal of mercury may be regulated due to environmental considerations.

Dispose of the used lamp unit by the approved method for your area. For disposal or recycling information, please contact your local authorities.

5

Introduction

Cleaning

1)Remove the power plug before cleaning.

Never use solvents such as benzine or thinner to clean the TV.

•These solvents may distort the cabinet or damage its finish.

•If rubber or vinyl products remain in contact with the

TV for a long time, a stain may result.

If the cabinet becomes dirty, clean it with a soft, dry cloth.

When cleaning the surface of the LCD display, wipe the panel surface gently with a soft, dry cloth.

2)Periodically disconnect the power plug from the outlet and check it.

If dust has collected on the power plug connectors, clean off the dust with dry cloth.

This dust may cause a fire due to reduced insulation on the plug.

Clean here

Important information

1)About LCD screen

•If you have the LCD screen facing to the sun, the LCD screen will be damaged. Be aware of locating the TV in the place such as window side or outside of the room.

•Never press the LCD screen strongly or scratch it, and never put anything on it. These actions will damage the LCD screen.

2)About cabinet

Never spray volatile compounds such as insecticide on the cabinet.

This may cause a discoloration or damage the cabinet.

3)Some pixels of the screen do not light up

The LCD display panel is manufactured using an extremely high level of precision technology, however sometimes some pixels of the screen may be missing picture elements or have luminous spots. This is not a sign of a malfunction.

4)About Interference

The LCD display may cause interference in image, sound, etc. of other electronic equipment that receives electromagnetic waves (e.g. AM radios and video equipment).

5)About using under the low temperature places

If you use the TV in the room of 0°C or less, the picture brightness may vary until the LCD monitor warms up. This is not a sign of a malfunction.

6)About afterimage

If a still picture is displayed, an afterimage may remain on the screen, however it will disappear.

This is not a sign of malfunction.

Exemptions

•Toshiba is not liable for any damage caused by fires, natural disaster (such as thunder, earthquake, etc.), acts by third parties, accidents, owner's misuse, or uses in other improper conditions.

•Toshiba is not liable for incidental damages (such as profit loss or interruption in business, modification or erasure of record data, etc.) caused by use or inability to use of product.

•Toshiba is not liable for any damage caused by neglect of the instructions described in the owner's manual.

•Toshiba is not liable for any damage caused by misuse or malfunction through simultaneous use of this product and the connected equipment.

6

Getting started

Connecting an antenna

Optimum reception of color requires a good signal and will generally mean that an outdoor antenna must be used.

The exact type and positioning of the antenna will depend upon your particular area.

Your Toshiba dealer or service personnel can best advise you on which antenna to use in your area.

Before connecting the antenna cable, turn off all main power switches.

VHF

UHF

Outdoor antenna

Mixer

Decoder		TV back view

IN

OUT

Media Recorder

IN

OUT

Antenna cable (75 7 coaxial) (not supplied)

300 7 twin-lead feeder

Antenna adaptor	75 7
(not supplied)
	antenna
	terminal
75 7 coaxial cable

Plug

(not supplied) 75 7 antenna terminal

Exploring your new TV

Installing the remote control batteries

Remove the battery cover.

Insert two R03 (AAA) batteries matching the –/+ polarities of the battery to the –/+ marks inside the battery compartment.

Cautions:

•Dispose of batteries in a designated disposal area. Never throw batteries into a fire.

•Attention should be drawn to the environmental aspects of battery disposal.

•Never mix battery types or combine used batteries with new ones.

Notes:

•If the remote control does not operate correctly, or if the operating range becomes reduced, replace both batteries with new ones.

•If the batteries are dead or if you will not use the remote control for a long time, remove the batteries to prevent battery acid from leaking into the battery compartment.

Effective range

for 32WLT66A/37WLT66A/42WLT66A

within 5 m

for 47WLT66A

within

7

Getting started

TV top and front panel controls

•You can operate your TV using the buttons on the top or front panel, or the remote control. The back and side of the panel provide the terminal connections to connect other equipment to your TV (- “Connecting your TV” pages 33 - 38).

•For the use of each control, see the pages in brackets.

for 32WLT66A/37WLT66A/42WLT66A

TV top view

TV front view

You can swivel the TV screen.
Swivel angle: 15 degrees to	6
left and right.

1																2						3						4						5						7				8		9			10
for 47WLT66A
					TV top view																														TV front view

You can swivel the TV screen.
Swivel angle: 15 degrees to	6
left and right.

1		2				3		4					5							10			9					8								7

1o (Input source selection) — When no menu is onscreen, this button selects the input source (- page 25).

OK — When a Analog TV menu is on-screen, this button functions as the next menu navigation button (- page 11, 25).

2MENU — Press to access the TV SETUP menu (- page 11).

32 – + (Volume) — When no menu is on-screen, these buttons adjust the volume level (- page 10).

I i (MENU left/right) — When a Analog TV menu is onscreen, these buttons function as left/right menu navigation buttons or adjust settings (- page 11).

4pBb (Program position) — When no menu is onscreen, these buttons select the program position.

(- page 15).

Uu (MENU up/down) — When a Analog TV menu is on-screen, these buttons function as up/down menu navigation buttons (- page 11).

51 (Power on/Standby) — Press to turn the TV on/ standby (-page 12).

6! (Power switch) — Press to turn the TV on and off (- page 12).

7(Remote sensor) — Point the remote control toward this remote sensor (- page 12).

8! (Power LED) — Power indicator (- page 12).

94 (On timer LED) — Timer indicator (- page 25).

10● (DTV timer LED) — Digital TV timer Recording Indicator (- page 24).

8

Getting started

TV side and back panel connections

for 32WLT66A/37WLT66A/42WLT66A

11

12

13

DIGITAL TV

VIDEO

L

	AUDIO	VIDEO	Y
	R
		L/MONO	PB/CB
	L
		AUDIO	PR/CR
	R	R
	PC/HDMI-1	COMPONENT
		VIDEO INPUT
	(AUDIO)

TV back view

* You can use the cable holder to

hold antenna cable, video and

audio cables etc.

When moving the TV, never hold this holder.

Right side view	Power cord

		S-VIDEO
Headphones	14	VIDEO
		L/MONO
(Not supplied)		AUDIO
		R

15	16	17	18	19

for 47WLT66A	Right side view
	11

12

13

COMPONENT
VIDEO INPUT	VIDEO
Y
PB/CB	L/MONO
PR/CR	AUDIO
	R
VIDEO
L/MONO
	L
AUDIO
R	R
DIGITAL TV	PC/HDMI-1
	(AUDIO)

TV back view

* You can use the cable holder to

hold antenna cable, video and

audio cables etc.

When moving the TV, never hold this holder.

Power cord

		S-VIDEO
Headphones		VIDEO
	14		16	17	18	19
(Not supplied)		L/MONO
		AUDIO
		R

15

11o (1) (Video 1 input terminals) — High-definition component video or standard (composite) video and standard (analog) stereo audio inputs (- page 33).

12O DIGITAL TV (output terminals) — For use when connecting a VCR/HDD/DVD video recorder with standard video and standard audio inputs (- page 33). No On-Screen-Display will output from this terminals.

13o PC/HDMI1 (AUDIO) (input terminals) — For use when connecting a personal computer (PC) or a DVI device with standard audio output (- page 33, 36).

14o (2) (Video 2 input terminals) — Optional S-video or standard video and standard audio inputs (- page 35).

15D (Headphone jack) — For use with headphones.

Note:

When the Headphone jack is being used, the sound from all speakers will be muted, and normal sound will be output to the headphones only.

16A (Antenna input terminal) — Analog antenna signal input (- page 7).

17o RGB/PC (input terminal) — For use when connecting a personal computer (PC) (- page 37).

18o HDMI1 and o HDMI2 (input terminals) — HighDefinition Multimedia Interface input receives digital audio and uncompressed digital video from an HDMI device or uncompressed digital video from a DVI device (- page 35).

19O Digital Audio (optical) (output terminal) — For use when connecting an amplifier with optical type digital audio input (- page 33).

9

Getting started

Learning about the remote control

Location of controls

To switch between Analog and Digital TV (- page 11)

To return to the previous program (- page 16)

To display digital on-screen information (- page 29)

MENU (- page 11)

•Menu U u I i (- page 11)

•OK (- pages 11, 25)

Program position Bb (- page 16)

To select TV, STB or DVD mode

•Stereo/bilingual selection (- page 22)

•To display the Audio Track menu in Digital TV (- page 32)

Sound mute (This button turns off/on the sound.)

When using Toshiba STB or DVD, press to PAUSE *

press to PLAY ** press to REVERSE press to FORWARD press to EJECT press to STOP

press to SKIP REVERSE press to SKIP FORWARD * For HDD-J35 and HDD-S36,

this is also the PLAY key.

**Not applicable to HDD-J35 and HDD-S36, where the PLAY key is shared with PAUSE.

Teletext control buttons (Four colored buttons : Red, Green, Yellow, Blue)

(- page 27)

Power on/Standby (- page 12)

Number buttons (0-9) (- pages 16, 24)

•Input source selection

(o1 - o2, HDMI1, HDMI2, PC) (- page 25)

•To access sub-pages

when in teletext - analog only - (- page 26)

To switch between Navigation

List and Favorite List (- pages 16, 31) EXIT (- page 12)

Volume – +

(These buttons adjust the volume level.)

•/ To display on-screen information (- page 16)

• Initial/index function for Teletext

-analog only - (- page 28)

Teletext on/Superimpose Teletext/off (- pages 28)

When in TV mode:

Picture still (- page 19)

Picture size selection (- page 18)

Picture mode selection (- page 19)

Digital subtitle on/off (- page 31)

When in teletext - analog only:

To reveal concealed text (- page 28)

To hold a wanted page (- page 28)

To enlarge teletext display size (- page 28)

• To select a page while viewing a normal picture (- page 28)

•To select the time display (- page 28)

10

Getting started

This integrated TV is equipped with both Digital and Analog system. To switch between Digital and Analog TV press ATV/DTV on the remote control.

Learning about the menu system

We suggest you familiarize yourself with the display charts before using the menu system:

•Press M to display menu, then press I or i to select main menu headings.

•Press u or U to select an item.

•Press I or i to select or adjust setting.

•Press Q to display the next menu.

Displaying the DIGITAL SETTING chart

This menu will display only Digital TV selected.

PROGRAM menu

DIGITAL SETTINGS DIGITAL SETTINGS

PROGRAM

PROGRAM

Channel List

Channel List

Parental Rate

No Block

Parental Rate

No Block

EPG

EPG

Timer

Timer

Back

Select Function

Watch TV

Back

Select Function

Watch TV

SCAN menu

DIGITAL SETTINGS

DIGITAL SETTINGS

SCAN

SCAN

Auto Scan

Auto Scan

Manual Scan

Manual Scan

Back

Select Function

Watch TV

Back

Select Function

Watch TV

SYSTEM menu

DIGITAL SETTINGS

DIGITAL SETTINGS

SYSTEM

SYSTEM

Password

* * * *

Password

* * * *

Information

Information

Restore Factory Setting

Restore Factory Setting

Back

Select Function

Watch TV

Back

Select Function

Watch TV

PROFILE menu

DIGITAL SETTINGS

DIGITAL SETTINGS

PROFILE

PROFILE

Digital Output

Bitstream

Digital Output

Bitstream

Audio Track

Dolby ...

Audio Track

Dolby ...

Favourite Mode

On

Favourite Mode

On

Time zone

GMT +08:30

Time zone

GMT +08:30

Transparency

70

Transparency

70

I-Plate

I-Plate

Back

Select Function

Watch TV

Back

Select Function

Watch TV

TV SETUP menu

DIGITAL SETTINGS

TV SETUP

PICTURE

Picture settings

OK

Press OK for basic TV settings

3D Color management

Off

Base color adjustment

Cinema mode

On

Displaying the TV SETUP menu chart

When Analog TV is selected, press M will display the TV SETUP menu.

When Digital TV is selected, select the TV SETUP menu from DIGITAL SETTING chart.

There will be some functions which not available in Digital TV and these will appear in gray scale.

PICTURE menu

PICTURE

PICTURE

Picture settings

OK

Picture settings

OK

3D Color management

Off

3D Color management

Off

Base color adjustment

Base color adjustment

Cinema mode

On

Cinema mode

On

MENU Back

EXIT Watch TV

MENU Back

EXIT Watch TV

SOUND

menu

SOUND

2/2

Stable sound

Off

Bass boost

Off

SOUND

1/2

MTS

Auto

SOUND

1/2

Dual

Dual 1

Bass

0

MTS

Auto

Treble

0

Dual

Dual 1

Balance

0

Bass

0

WOW

OK

Treble

0

MENU Back

EXIT Watch TV

Balance

0

WOW

OK

SET UP

MENU Back

EXIT Watch TV

menu

SET UP

SET UP

Language

English

Language

English

Auto tuning

OK

Auto tuning

OK

Manual tuning

OK

Manual tuning

OK

ANT ATT

Off

ANT ATT

Off

AV connection

OK

AV connection

OK

Picture position

OK

Picture position

OK

MENU Back

EXIT Watch TV

MENU Back

EXIT Watch TV

TIMER

menu

TIMER

TIMER

Sleep timer

00:00

Sleep timer

00:00

On timer

00:00

On timer

00:00

MENU Back

EXIT Watch TV

MENU Back

EXIT Watch TV

FUNCTION

menu

FUNCTION

FUNCTION

Teletext

Auto

Teletext

Auto

Auto format

On

Auto format

On

Blue screen

On

Blue screen

On

Side panel

1

Side panel

1

MENU Back

EXIT Watch TV

MENU Back

EXIT Watch TV

Back Select Function

Watch TV

MENU Back EXIT Watch TV

11

Getting started

Notes for menu system:

•In the video input mode (o1 , o2), Auto tuning and

Manual tuning are not available. Instead, Manual setting appears in the SET UP menu (- page 25).

•If you connect external equipment via component video source to external input, Color system selection in the Manual setting menu is not available.

•If you do not make a selection for a while, the menu display disappears automatically.

•If you want to close the menu display instantly, press P.

•To return to the previous menu, press M.

•In the PC input mode, PC Setting appears in the SET UP menu (- page 38).

•In the 480i or 576i input signals mode, you can select the Cinema mode in the PICTURE menu (- page 21).

•When you use the color management function (- page 20), you can select the Base color adjustment in the PICTURE menu.

Turning the TV on

Switching on the TV

Connect the power cord to a wall outlet.

1 Press ! on the TV left side until it clicks.

1

Mono

The ! Power indicator lights in red to indicate to standby. Press on the remote control or 1 on the TV top or front panel, power indicator will be green to indicate to turn on.

Notes:

•When the TV is turned on from ! on the left side (full power cut-off mode), a start-up time of approximate 25 seconds is required before entering the standby mode. During this time, no function can be activated with the remote control or the buttons on the TV. This is not a malfunction of the TV.

•If you watch black and white programs when the color system mode is set to Auto, color noise may appear on the screen. In this case select the appropriate Color system (For the system of each country or region, refer to pages 15 and 41).

Switching off the TV

1 Press on the remote control or 1 on the TV top or front panel to switch to the standby mode.

2 To switch the TV off, press ! on the TV left side. Power indicator will be turned off.

Notes:

•This TV is not fully disconnected from the main supply, as minute current is consumed even when ! is turned off. When the TV will not be used for a long period of time, such as during vacation or travel, remove the power plug from the wall outlet.

•The TV will automatically turn itself off after approximately 15 minutes if it is tuned to a vacant channel or a station that completes its broadcast for the day. This function does not work in external input or Blue screen Off mode.

The TV will automatically turn itself off after approximately 2 hours if you do not operate the TV after turned on by on timer function.

•If power is cut off while you are viewing the TV, the Last Mode Memory function turns on the TV automatically when power is applied again. If power is going to be off for a long time and you are going to be away from your TV, unplug the power cord to prevent the TV from turning on in your absence.

12

Getting started

Tuning the TV for the first time

- digital only -

Before switching on the TV, put your decoder and media recorder to Standby if they are connected and ensure the antenna is connected. To setup the TV use the buttons on the remote control as detailed on page 10.

1 Press , the Welcome screen will appear. This screen will appear the first time that the TV is switched on and each time the TV is reset.

Thank you for choosing TOSHIBA television.

First you need to tune in your television.

Please ensure aerial is connected before proceeding.

Press to continue.

2 Press Q to proceed.

3 The Select Location screen will appear. Press u or U to select the state in which you live.

Select Location
Australian Capital Territory
New South Wales
Northern Territory
Queensland
South Australia
Tasmania
Victoria
Western Australia
MENU Back Select Function	EXIT Watch TV

4 Press Q to start tuning. The Auto Scan screen will appear and the TV will automatically start to search for available stations. The progress bar will move along the line.

						Auto Scan
Channel 6 found...
06-0007			7 Digital							Northern Territory
06-0070			7	Digital HD
06-0071			7	Digital 1
06-0072			7	Digital 2
06-0073			7	Digital 3
06-0077			7	Digital Guide
Scan Status				6/69
Scan Percentage
	Back Select Function										Watch TV

5 When the search is completed, the TV will automatically turn to the lowest logical channel number. See the following for more details on Auto Scan.

Note:

If you do not live in Australia, press P at the Select Location. Press M, then press I or i to select PROFILE.

Press u or U to select Time Zone to set your time zone (- page 24).

Then use Manual Scan to start tuning (- page 14).

Programming channels into the TV’s channel memory

Auto scan - digital only -

As new services are broadcast, it will be necessary to re-tune the TV in order to view them.

Auto scan will completely re-tune the TV and can be used to update the channel list. It is recommended that Auto scan is run periodically to ensure that all new services are added. All stored programs and settings, including Timer entries, favorites and locked programs, will be lost.

1

Press M and I or i to select the SCAN menu.

2

Use u to select Auto Scan.

3

Press Q to display Password. Enter your password

(- page 29) using the number buttons or press 0000

(which is the default password).

Password

Blocking active

Enter PIN code

To temporarily unblock

Back

Watch TV

4 The Select Location will appear. Current location will be highlighted. Press u or U to select a state in which you live.

5 Press Q, a confirmation screen will appear indicating that All existing channels will be deleted. Continue? select Yes.

6 Press Q to start Auto tuning.

						Auto Scan
Channel 6 found...
06-0007			7 Digital						Northern Territory
06-0070			7	Digital HD
06-0071			7	Digital 1
06-0072			7	Digital 2
06-0073			7	Digital 3
06-0077			7	Digital Guide
Scan Status				6/69
Scan Percentage
	Back Select Function									Watch TV

The above sample display shows Auto Scan in progress. The channel number is shown as “06-0007” etc., where “06” is the physical channel number and “0007” is the logical channel number (which is the 4-digit number you enter when changing channels).

7 When the search is complete, the TV will automatically tune to the lowest logical channel number.

13

Getting started

Note:

After the Auto scan, the TV may have scanned identical channels being broadcast from different transmitters. You can verify this by previewing those channels in the Channel List with identical logical numbers and check on their physical channel numbers (- page 30). If you do find channels with the same logical channel numbers but different physical channel numbers, it is recommended that you delete these duplicate channels and keep only one channel with the best signal strength as indicated by the SNR indicator in the I-Plate (- page 16) display.

Manual scan - digital only -

If there were any missing channel after Auto Scan, these channels might be found by using Manual Scan described in this section. Also, if you do not live in Australia, you must use Manual Scan to scan those channels in your country.

1 From the SCAN menu, press u or U to select Manual Scan, then press Q.

2 Enter password using the Number buttons or press 0000 (which is the default password), then Manual Scan will appear.

			Manual Scan
	Channel No.		6
	Frequency		1775000 KHz			Scanning...
	Bandwidth
			7 MHz
	Priority
			HIGH
						Signal Level	100%
	Start Scan					Quality	70%
						SNR: 20dB
	Back	Select Function					Watch TV

3 Press u or U to select the item you wish to adjust. For Australia, to adjust Frequency, you may refer to the latest channel table from local dealer. And the Bandwidth is 7MHz and Priority should be set to HIGH. Then press u or U to select Start Scan and press Q to start scanning.

4 If scanning was successful, Get Channel Success appeared for 2 seconds. Repeat to scan other channels as necessary.

5 If scanning was unsuccessful, Timeout Error appeared. At this point you can rescan the signal or refer to the Signal Level bar and Quality for aligning the direction of the antenna to get the signal. Refer to your antenna installer if problem persists.

Notes:

•Signal level refers to the input Radio Frequency (RF) signal strength as perceived by the TV. Note that too strong signal may cause erroneous readings. If you use an antenna booster and find that you still get a low signal level, your booster gain may be set too high. In this case, adjust the gain accordingly. You may also see the No Signal on the screen when the signal level is low.

•Quality refers to the quality of the received digital signal. A high value of quality means that there are few errors in the signal. In the same way, a low value of quality implies that there are a large number of errors in the signal, which may cause distortions in video and audio.

Programming channels automatically

- analog only -

First, use the Auto tuning function to preset all the active channels in your area automatically. Then, arrange the preset channels with the Manual tuning function so that you can tune into only desired channels.

1 Press M, then press I or i to display the SET UP menu.

2 Press u or U to select Auto tuning.

SET UP
Language		English
Auto tuning		OK
Manual tuning		OK
ANT ATT		Off
AV connection		OK
Picture position		OK
MENU Back EXIT Watch TV

3 Press Q to display the Auto tuning menu.

Auto tuning

!Press OK key to start. EXIT for no change.

MENU Back EXIT Watch TV

4 Press Q to start the automatic search.

The search will begin for all available stations.

Auto tuning

Searching

Pos :2

EXIT Stop

The slide bar will move along the line as the search progresses.

If you make a mistake, simply repeat steps 1-4 to start again from the beginning.

5 When the automatic search is completed, the TV will automatically return to the first program position.

6 Press > or < to view the programmed position.

Note:

When you preset the program channel which sound of broadcast transmission system adopts “M” system, the sound system may not be tuned correctly if the radio waves transmit badly. At that time, preset the channel by Manual tuning. The countries such as Myanmar, Brazil, Chile, Colombia apply to this case. See page 41 for more details.

14