TORO TIMECUTTER Z SERVICE MANUAL
Table of Contents – Page 1 of 2
QUICK REFERENCE SAFETY INFORMATION
GENERAL INFORMATION THINK SAFETY FIRST
SPECIFICATIONS
ENGINE SPECIFICATIONS - (Z16-44 & Z17-44) ENGINE SPECIFICATIONS - (Z17-52 & Z18-52)
BOLT TORQUES MAINTENANCE SCHEDULE
Z16-44
Z17-44 & Z17-52
Z18-52
MODEL/SERIAL NUMBER LOCATION
GREASING AND LUBRICATION
SERVICE INTERVAL/SPECIFICATION
LUBRICATION POINTS
ENGINE
BRIGGS & STRATTON ENGINE
KOHLER ENGINE
KAWASAKI ENGINE
BRIGGS & STRATTON AIR CLEANER
KOHLER AIR CLEANER
KAWASAKI AIR CLEANER
SPARK PLUG
ENGINE REMOVE AND REPLACE
TRANSAXLE
TROUBLESHOOTING CHECKLIST FLUIDS
REMOVE AND REPLACE TRANSAXLE REASSEMBLY
CONTROL HANDLE-RETURN TO NEUTRAL ADJUSTMENT PURGING THE SYSTEM
NEUTRAL ADJUSTMENT
TRACKING ADJUSTMENT CONTROL HANDLE ADJUSTMENT
CHASSIS
REMOVE AND REPLACE DAMPERS REMOVE AND REPLACE CONTROL LINKAGE REPLACE CONTROL LINKAGE
REMOVE AND REPLACE BRAKE LINKAGE REPLACE BRAKE LINKAGE
PARKING BRAKE ADJUSTMENT REPLACE TRACTION BELT
TORO TIMECUTTER Z SERVICE MANUAL
Table of Contents – Page 2 of 2
MOWER DECKS: 44” AND 52” DECK ASSEMBLIES BELT REMOVAL AND REPLACEMENT MOWER DECK REMOVE AND REPLACE MOWER DECK SIDE TO SIDE ADJUSTMENT
MOWER DECK FRONT TO REAR ADJUSTMENT SPINDLE BEARING REPLACEMENT
ELECTRICAL SYSTEMS
SAFETY INTERLOCK SYSTEM
INTERLOCK COMPONENTS
ELECTRICAL COMPONENTS
ELECTRIC CLUTCH
ELECTRICAL SCHEMATICS
BRIGGS & STRATTON
KAWASAKI
KOHLER
TimeCutter® Z
TimeCutter® ZX
Service Manual
ABOUT THIS MANUAL
This service manual was written expressly for Toro service technician. The Toro Company has made every effort to make the information in this manual complete and correct.
Basic mechanical/electrical skills are assumed. The Table of Contents lists the systems and the related topics covered in this manual.
For additional information on the electrical system, please refer to the Toro Electrical Demystification Guide (4924404). For information on the hydrostatic drive units, refer to the Integrated Zero-Turn Transaxle Service and Repair Manual (492-4737). For information specific to the engines used on this unit, refer to the appropriate engine manufacturer’s service and repair instructions.
We are hopeful that you will find this manual a valuable addition to your service shop. If you have any questions or comments regarding this manual, please contact us at the following address:
The Toro Company
Consumer Service Training Department
8111 Lyndale Avenue South
Bloomington, MN 55420
The Toro Company reserves the right to change product specifications or this manual without notice.
The automatic transmission and transaxle are sophisticated pieces of machinery. Maintain strict cleanliness control during all stages of service and repair. Cover or cap all hose ends and fittings whenever they are exposed. Even a small amount of dirt or other contamination can severely damage the system.
Copyright© All Rights Reserved
©2001 The Toro Company
TABLE OF CONTENTS
QUICK REFERENCE SECTION
Safety Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1a
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SERVICE SECTION
Model/Serial Number . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Greasing and Lubrication. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Transaxle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Chassis . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Mower Decks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Electrical Systems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1b
1c
2
3
4
5
6
7
8
TimeCutter™ Z Service Manual |
1 - 1 |
QUICK REFERENCE
Table of Contents
SAFETY INFORMATION
General Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 - 3
Think Safety First. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 - 3
SPECIFICATIONS
Engine Specifications - (Z16-44 & Z17-44) . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 - 4
Engine Specifications - (Z17-52 & Z18-52) . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 - 5
BOLT TORQUES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 - 6
MAINTENANCE SCHEDULE
Z16-44 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 - 7 Z17-44 & Z17-52 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 - 8
Z18-52 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 - 9
1 - 2 |
TimeCutter™ Z Service Manual |
SAFETY INFORMATION
This symbol means WARNING or |
tractor and attachment operator’s manuals contain |
|
|
PERSONAL SAFETY INSTRUCTION |
safety information and operating tips for safe operating |
|
|
- read the instruction because it has to |
practices. Operator’s manuals are available through |
|
|
do with your safety. Failure to comply |
your Toro parts source or: |
|
|
1a |
|||
with the instruction may result in |
The Toro Company |
||
personal injury or even death. |
|
||
|
|||
|
Publications Department |
|
|
This manual is intended as a service and repair manual |
8111 Lyndale Avenue South |
|
|
only. The safety instructions provided herein are for |
Bloomington, MN 55420 |
|
|
troubleshooting, service, and repair of the TimeCutter Z |
|
|
|
zero radius tractor. The TimeCutter Z zero radius |
|
|
THINK SAFETY FIRST
Avoid unexpected starting of engine...
Always turn off the engine and disconnect the spark plug wire(s) before cleaning, adjusting, or repair.
Avoid lacerations and amputations...
Stay clear of all moving parts whenever the engine is running. Treat all normally moving parts as if they were moving whenever the engine is running or has the potential to start.
Avoid burns...
Do not touch the engine, muffler, or other components which may increase in temperature during operation, while the unit is running or shortly after it has been running.
Avoid fires and explosions...
Avoid spilling fuel and never smoke while working with any type of fuel or lubricant. Wipe up any spilled fuel or oil immediately. Never remove the fuel cap or add fuel when the engine is running. Always use approved, labeled containers for storing or transporting fuel and lubricants.
Avoid asphyxiation...
Never operate an engine in a confined area without proper ventilation.
Avoid injury from batteries...
Battery acid is poisonous and can cause burns. Avoid contact with skin, eyes, and clothing. Battery gases can explode. Keep cigarettes, sparks, and flames away from the battery.
Avoid injury due to inferior parts...
Use only original equipment parts to ensure that important safety criteria are met.
Avoid injury to bystanders...
Always clear the area of bystanders before starting or testing powered equipment.
Avoid injury due to projectiles...
Always clear the area of sticks, rocks, or any other debris that could be picked up and thrown by the powered equipment.
Avoid modifications...
Never alter or modify any part unless it is a factory approved procedure.
Avoid unsafe operation...
Always test the safety interlock system after making adjustments or repairs on the machine. Refer to the Electrical section in this manual for more information.
TimeCutter™ Z Service Manual |
1 - 3 |
SPECIFICATIONS
Specifications
|
|
|
|
|
|
|
|
|
Z16-44 |
Z17-44 |
|
|
|
|
|
|
|
|
|
ENGINE: |
|
|
|
|
|
High Idle |
3400 ± 100 RPM |
3400 ± 100 RPM |
|
|
|
|
|
|
|
|
|
Low Idle |
1400 RPM |
1400 RPM |
|
1b |
|
||||
|
|
|
|
|
|
|
Manufacturer |
Briggs & Stratton |
Kohler |
|
|
|
|
Horsepower (kW) |
16.5 HP (12.3kW) @ 3600 RPM |
17 HP (12.7 kW) @ 3600 RPM |
|
|
|
||||
|
|
|
|
|
|
|
|
Fuel |
Unleaded Gasoline 87 octane min. |
Unleaded Gasoline 87 octane min. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
FUEL SYSTEM: |
|
|
|
|
|
Capacity |
5 Gallon (18.9 L) |
5 Gallon (18.9 L) |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
TRACTION SYSTEM: |
|
|
|
|
|
Transaxles |
Twin Hydro-Gear IZT Hydrostatic |
Twin Hydro-Gear IZT Hydrostatic |
|
|
|
|
Transaxles |
Transaxles |
|
|
|
|
|
|
|
|
|
Transaxle Drive |
Belt drive with self-tensioning system |
Belt drive with self-tensioning system |
|
|
|
|
|
|
|
|
|
Ground Speed |
Infinite, 0 to 6.5 MPH (10.5-km/hr) forward |
Infinite, 0 to 6.5 MPH (10.5-km/hr) forward |
|
|
|
|
0 to 3.4 MPH (5.5-km/hr) reverse |
0 to 3.4 MPH (5.5-km/hr) reverse |
|
|
|
|
|
|
|
|
|
TIRES: |
|
|
|
|
|
Rear Drive Tires |
18x10-8 4 ply with “Multitrac CS” Tread |
18x10-8 4 ply with “Multitrac CS” Tread |
|
|
|
|
|
|
|
|
|
Front Caster Tires |
410/350 x 4 - 4.25 IS with “sawtooth” tread |
410/350 x 4 - 4.25 IS with “sawtooth” tread |
|
|
|
|
|
|
|
|
|
Tire Pressure |
13 psi (90 kPa) rear, 35 psi (241 kPa) front |
13 psi (90 kPa), rear 35 psi (241 kPa) front |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
ELECTRICAL |
|
|
|
|
|
SYSTEM: |
|
|
|
|
|
Battery Voltage |
12 volt, negative ground |
12 volt, negative ground |
|
|
|
|
|
|
|
|
|
Battery Type |
BCI Group U1 |
BCI Group U1 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
DIMENSIONS: |
|
|
|
|
|
Wheel Base |
52.1 in. (132.3 cm) center of caster to |
52.1 in. (132.3 cm) center of caster to |
|
|
|
|
center of drive tires |
center of drive tires |
|
|
|
|
|
|
|
|
|
Overall Width |
55 in. (139.7 cm) with deck deflector down |
55 in. (139.7 cm) with deck deflector down |
|
|
|
|
46.6 in. (118.4 cm) gate width with deck |
46.6 in. (118.4 cm) gate width with deck |
|
|
|
|
deflector up |
deflector up |
|
|
|
|
|
|
|
|
|
Overall Length |
77.5 in. (196.9 cm) |
77.5 in. (196.9 cm) |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
WEIGHT: |
|
|
|
|
|
Net Weight |
635 lbs. (approx.) |
635 lbs. (approx.) |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
HEIGHT OF CUT: |
|
|
|
|
|
|
Adjusts from 1.5” (3.8 cm) to |
Adjusts from 1.5” (3.8 cm) to |
|
|
|
|
4.5” (11.4 cm) (7 positions) |
4.5” (11.4 cm) (7 positions) |
|
|
|
|
|
|
|
1 - 4 |
TimeCutter™ Z Service Manual |
|
|
|
SPECIFICATIONS |
|
|
Specifications (cont’d) |
|
|
|
||
|
|
Z17-52 |
Z18-52 |
|
|
|
|
|
|
|
|
|
ENGINE: |
|
|
|
|
|
High Idle |
3400 ± 100 RPM |
3400 ± 100 RPM |
|
|
|
|
|
|
|
|
|
Low Idle |
1400 RPM |
1400 RPM |
|
|
|
1b |
||||
|
|
|
|
|
|
|
Manufacturer |
Kohler |
Kawasaki |
|
|
|
Horsepower (kW) |
17 HP (12.7kW) @ 3600 RPM |
18 HP (13.4kW) @ 3600 RPM |
|
|
|
|
||||
|
|
|
|
|
|
|
Fuel |
Unleaded Gasoline 87 octane min. |
Unleaded Gasoline 87 octane min. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
FUEL SYSTEM: |
|
|
|
|
|
Capacity |
5 Gallon (18.9 L) |
5 Gallon (18.9 L) |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
TRACTION SYSTEM: |
|
|
|
|
|
Transaxles |
Twin Hydro-Gear IZT Hydrostatic |
Twin Hydro-Gear IZT Hydrostatic |
|
|
|
|
Transaxles |
Transaxles |
|
|
|
|
|
|
|
|
|
Transaxle Drive |
Belt drive with self-tensioning system |
Belt drive with self-tensioning system |
|
|
|
|
|
|
|
|
|
Ground Speed |
Infinite, 0 to 6.5 MPH (10.5-km/hr) forward |
Infinite, 0 to 6.5 MPH (10.5-km/hr) forward |
|
|
|
|
0 to 3.4 MPH (5.5-km/hr) reverse |
0 to 3.4 MPH (5.5-km/hr) reverse |
|
|
|
|
|
|
|
|
|
TIRES: |
|
|
|
|
|
Rear Drive Tires |
18x10-10-10.5 4 ply with “Multitrac CS” |
18x10-10-10.5 4 ply with “Multitrac CS” |
|
|
|
|
Tread |
Tread |
|
|
|
|
|
|
|
|
|
Front Caster Tires |
410/350 x 4 - 4.25 IS with “sawtooth” tread |
410/350 x 4 - 4.25 IS with “sawtooth” tread |
|
|
|
|
|
|
|
|
|
Tire Pressure |
13 psi (90 kPa) rear, 35 psi (241 kPa) front |
13 psi (90 kPa) rear, 35 psi (241 kPa) front |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
ELECTRICAL SYSTEM: |
|
|
|
|
|
Battery Voltage |
12 volt, negative ground |
12 volt, negative ground |
|
|
|
|
|
|
|
|
|
Battery Type |
BCI Group U1 |
BCI Group U1 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
DIMENSIONS: |
|
|
|
|
|
Wheel Base |
52.1 in. (132.3 cm) center of caster to |
52.1 in. (132.3 cm) center of caster to |
|
|
|
|
center of drive tires |
center of drive tires |
|
|
|
|
|
|
|
|
|
Overall Width |
65 in. (165.1 cm) with deck deflector down |
65 in. (165.1 cm) with deck deflector down |
|
|
|
|
58 in. (147.3 cm) gate width with deck |
58 in. (147.3 cm) gate width with deck |
|
|
|
|
deflector up |
deflector up |
|
|
|
|
|
|
|
|
|
Overall Length |
77.5 in. (196.9 cm) |
77.5 in. (196.9 cm) |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
WEIGHT: |
|
|
|
|
|
Net Weight |
680 lbs. (approx.) |
680 lbs. (approx.) |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
HEIGHT OF CUT: |
|
|
|
|
|
|
Adjusts from 1.5” (3.8 cm) to 4.5” (11.4 cm) |
Adjusts from 1.5” (3.8 cm) to 4.5” (11.4 cm) |
|
|
|
|
(7 positions) |
(7 positions) |
|
|
|
|
|
|
|
|
TimeCutter™ Z Service Manual |
1 - 5 |
SPECIFICATIONS
Specifications cont.
|
|
ZX 17K-44 |
ZX 17-44 |
|
Engine: |
17 hp Kohler® OHV, CV490S |
17 hp Briggs & Stratton OHV, 31F777 |
|
High Idle |
3400 + 100 RPM |
3400 + 100 RPM |
1b |
Low Idle |
1400 RPM |
N/A |
Horse Power |
17 (12.7kW) @3600 RPM |
17 (12.7kW) @3600 RPM |
|
|
|
|
|
|
Cubic Centimeter’s (cc’s) |
490 Dispacement |
500 Dispacement |
|
Fuel |
Unleaded Gasoline 87 octane min. |
Unleaded Gasoline 87 octane min. |
|
Oil Capacity |
2 qts. (1.9 L) |
1.75 qt. (1.7 L) |
|
Charge coil |
12v - 15 amp |
12v - 16 amp |
|
Construction: |
|
|
|
Front Frame |
Welded 1x2x.120” structural steel tube |
Welded 1x2x.120” structural steel tube |
|
Rear Frame |
Welded 7 & 10 ga. High strength steel |
Welded 7 & 10 ga. High strength steel |
|
Frame Assembly |
Front & rear frames bolted together. |
Front & rear frames bolted together. |
|
Deck |
Right side discharge, 44 in. cut, three |
Right side discharge, 44 in. cut, three |
|
|
blade mid-mounted rotary. Drawn 13 |
blade mid-mounted rotary. Drawn 13 |
|
|
gauge steel with welded mounting |
gauge steel with welded mounting |
|
|
brackets and gauge wheel brackets. |
brackets and gauge wheel brackets. |
|
|
Frame supported. |
Frame supported. |
|
|
|
|
|
Fuel System: |
Single fuel tank fender type mounted on |
Single fuel tank fender type mounted on |
|
|
the left side. |
the left side. |
|
Capacity |
5 Gallons (18.9 L) |
5 Gallons (18.9 L) |
|
|
Fuel tank shut off |
Fuel tank shut off |
|
|
In-line fuel fi lter |
In-line fuel fi lter |
|
Traction System: |
|
|
|
Transaxles |
Twin Hydro-Gear IZT Hydrostatic |
Twin Hydro-Gear IZT Hydrostatic |
|
|
Transaxles |
Transaxles |
|
Transaxle Drive |
Belt Drive with self-tensioning system |
Belt Drive with self-tensioning system |
|
Ground speed forward |
Infi nite, 0 to 6.5-MPH (10.5-km/hr) |
Infi nite, 0 to 6.5-MPH (10.5-km/hr) |
|
Ground speed reverse |
0 to 3.4-MPH (5.5-km/hr) |
0 to 3.4-MPH (5.5-km/hr) |
|
Transport rods |
Allows unit to be moved without engine |
Allows unit to be moved without engine |
|
|
running. |
running. |
|
Attachment Drive: |
|
|
|
Clutch |
Electric |
Electric |
|
Type |
Vertical Drive with Single Deep B-Groove |
Vertical Drive with Single Deep B-Groove |
|
|
Pulley |
Pulley |
A1-6 |
TimeCutter ZX Service Manual |
|
|
|
SPECIFICATIONS |
|
|
Specifications cont. |
|
|
|
|
|
|
|
|
|
|
|
|
|
ZX 17K-44 |
ZX 17-44 |
|
|
Tires: |
|
|
|
|
|
Rear Drive Tires |
|
18x10-8 4 ply with “Multitrac CS” Tread |
18x10-8 4 ply with “Multitrac CS” Tread |
|
|
Front Castor Tires |
|
410/350x4 - 4.25 IS with “sawtooth” tread |
410/350x4 - 4.25 IS with “sawtooth” tread |
1b |
|
Tire Pressure |
|
13 psi (90kPa) rear, 35 psi (241kPa) front |
13 psi (90kPa) rear, 35 psi (241kPa) front |
||
|
|
|
|
|
|
Electrical System: |
|
|
|
|
|
Battery voltage |
|
12 volt negative ground. |
12 volt negative ground. |
|
|
Fused |
|
(1) 30 amp blade type main. |
(1) 30 amp blade type main. |
|
|
|
|
(1) 25 amp blade type charge system. |
(1) 25 amp blade type charge system. |
|
|
|
|
(1) 10 amp included with optional light kit. |
(1) 10 amp included with optional light kit. |
|
|
Dimensions: |
|
|
|
|
|
Wheel Base |
|
52.1” (132.3cm) center of castor wheel to |
52.1” (132.3cm) center of castor wheel to |
|
|
|
|
center of drive tires. |
center of drive tires. |
|
|
Width |
|
43” (109.2cm) outside rear tires. |
43” (109.2cm) outside rear tires. |
|
|
Overall Width |
|
55” (139.7cm) with deck defl ector down. |
55” (139.7cm) with deck defl ector down. |
|
|
|
|
46.6” (188.4cm) Gate width with deck |
46.6” (188.4cm) Gate width with deck |
|
|
|
|
defl ector up. |
defl ector up. |
|
|
Overall Length |
|
77.5” (196.9cm) |
77.5” (196.9cm) |
|
|
Overall Height |
|
40” (101.6cm) |
40” (101.6cm) |
|
|
Track Width |
|
35.2” (89.4cm) center to center of rear |
35.2” (89.4cm) center to center of rear |
|
|
|
|
tires. |
tires. |
|
|
|
|
30.4” (77.2cm) center to center of castor |
30.4” (77.2cm) center to center of castor |
|
|
|
|
tires. |
tires. |
|
|
Deck Width |
|
55” (139.7cm) with defl ector down. |
55” (139.7cm) with defl ector down. |
|
|
|
|
|
|
|
|
Weight: |
|
635 lbs. (288kg) (estimated) |
635 lbs. (288kg) (estimated) |
|
|
|
|
|
|
|
|
Height of Cut: |
|
Adjusts from 1.5” to 4.5” (7 postions) |
Adjusts from 1.5” to 4.5” (7 postions) |
|
|
|
|
|
|
|
|
Tip Speed: |
|
18,160 ft/min @ 3400 RPM nominal |
18,160 ft/min @ 3400 RPM nominal |
|
|
|
|
18,770 ft/min @ 3500 RPM max |
18,770 ft/min @ 3500 RPM max |
|
|
TimeCutter ZX Service Manual |
A1-7 |
SPECIFICATIONS
Specifications cont.
|
|
ZX 17-52 |
ZX 18-52 |
|
Engine: |
17 hp Kohler® OHV, CV490S |
18 hp Kawasaki OHV, FH531V |
|
High Idle |
3400 + 100 RPM |
3400 + 100 RPM |
1b |
Low Idle |
1400 RPM |
1400 RPM |
Horse Power |
17 (12.7kW) @3600 RPM |
18 HP (13.4kW) @3600 RPM |
|
|
|
|
|
|
Cubic Centimeter’s (cc’s) |
490 Dispacement |
494 Displacement |
|
Fuel |
Unleaded Gasoline 87 octane min. |
Unleaded Gasoline 87 octane min. |
|
Oil Capacity |
2 qts. (1.9 L) |
1.9 qts (1.8 L) |
|
Charge coil |
12v - 15 amp |
12v - 13 amp |
|
Construction: |
|
|
|
Front Frame |
Welded 1x2x.120” structural steel tube |
Welded 1x2x.120” structural steel tube |
|
Rear Frame |
Welded 7 & 10 ga. High strength steel |
Welded 7 & 10 ga. High strength steel |
|
Frame Assembly |
Front & rear frames bolted together. |
Front & rear frames bolted together. |
|
Deck |
Right side discharge, 52 in. cut, three |
Right side discharge, 52 in. cut, three |
|
|
blade mid-mounted rotary. Drawn 12 |
blade mid-mounted rotary. Drawn 12 |
|
|
gauge steel with welded mounting |
gauge steel with welded mounting |
|
|
brackets and gauge wheel brackets. |
brackets and gauge wheel brackets. |
|
|
Frame supported. |
Frame supported. |
|
|
|
|
|
Fuel System: |
Single fuel tank fender type mounted on |
Single fuel tank fender type mounted on |
|
|
the left side. |
the left side. |
|
Capacity |
5 Gallons (18.9 L) |
5 Gallons (18.9 L) |
|
|
Fuel tank shut off |
Fuel tank shut off |
|
|
In-line fuel fi lter |
In-line fuel fi lter |
|
Traction System: |
|
|
|
Transaxles |
Twin Hydro-Gear IZT Hydrostatic |
Twin Hydro-Gear IZT Hydrostatic |
|
|
Transaxles |
Transaxles |
|
Transaxle Drive |
Belt Drive with self-tensioning system |
Belt Drive with self-tensioning system |
|
Ground speed forward |
Infi nite, 0 to 6.5-MPH (10.5-km/hr) |
Infi nite, 0 to 6.5-MPH (10.5-km/hr) |
|
Ground speed reverse |
0 to 3.4-MPH (5.5-km/hr) |
0 to 3.4-MPH (5.5-km/hr) |
|
Transport rods |
Allows unit to be moved without engine |
Allows unit to be moved without engine |
|
|
running. |
running. |
|
Attachment Drive: |
|
|
|
Clutch |
Electric |
Electric |
|
Type |
Vertical Drive with Single Deep B-Groove |
Vertical Drive with Single Deep B-Groove |
|
|
Pulley |
Pulley |
A1-8 |
TimeCutter ZX Service Manual |
|
|
|
SPECIFICATIONS |
|
|
Specifications cont. |
|
|
|
|
|
|
|
|
|
|
|
|
|
ZX 17-52 |
ZX 18-52 |
|
|
Tires: |
|
|
|
|
|
Rear Drive Tires |
|
18x10-8 4 ply with “Multitrac CS” Tread |
18x10-10.5 4 ply with “Multitrac CS” |
|
|
|
|
|
Tread |
|
|
|
|
|
1b |
||
Front Castor Tires |
|
410/350x4 - 4.25 IS with “sawtooth” tread |
410/350x4 - 4.25 IS with “sawtooth” tread |
||
Tire Pressure |
|
13 psi (90kPa) rear, 35 psi (241kPa) front |
13 psi (90kPa) rear, 35 psi (241kPa) front |
|
|
Electrical System: |
|
|
|
|
|
Battery voltage |
|
12 volt negative ground. |
12 volt negative ground. |
|
|
Fused |
|
(1) 30 amp blade type main. |
(1) 30 amp blade type main. |
|
|
|
|
(1) 25 amp blade type charge system. |
(1) 25 amp blade type charge system. |
|
|
|
|
(1) 10 amp included with optional light kit. |
(1) 10 amp included with optional light kit. |
|
|
Dimensions: |
|
|
|
|
|
Wheel Base |
|
52.1” (132.3cm) center of castor wheel to |
52.1” (132.3cm) center of castor wheel to |
|
|
|
|
center of drive tires. |
center of drive tires. |
|
|
Width |
|
47.6” (120.9cm) outside rear tires. |
47.6” (120.9cm) outside rear tires. |
|
|
Overall Width |
|
65” (165.1cm) with deck defl ector down. |
65” (165.1cm) with deck defl ector down. |
|
|
|
|
58” (147.3cm) Gate width with deck |
58” (147.3cm) Gate width with deck |
|
|
|
|
defl ector up. |
defl ector up. |
|
|
Overall Length |
|
77.5” (196.9cm) |
77.5” (196.9cm) |
|
|
Overall Height |
|
41” (104.1cm) |
41” (104.1cm) |
|
|
Track Width |
|
37.5” (95.3cm) center to center of rear |
37.5” (95.3cm) center to center of rear |
|
|
|
|
tires. |
tires. |
|
|
|
|
30.4” (77.2cm) center to center of castor |
30.4” (77.2cm) center to center of castor |
|
|
|
|
tires. |
tires. |
|
|
Deck Width |
|
65” (165.1cm) with deck defl ector down. |
65” (165.1cm) with defl ector down. |
|
|
|
|
|
|
|
|
Weight: |
|
680 lbs. (308.4kg) (estimated) |
680 lbs. (308.4kg) (estimated) |
|
|
|
|
|
|
|
|
Height of Cut: |
|
Adjusts from 1.5” to 4.5” (7 postions) |
Adjusts from 1.5” to 4.5” (7 postions) |
|
|
|
|
|
|
|
|
Tip Speed: |
|
17,410 ft/min @ 3400 RPM nominal |
17,410 ft/min @ 3400 RPM nominal |
|
|
|
|
17,980 ft/min @ 3400 RPM max |
17,980 ft/min @ 3500 RPM max |
|
|
TimeCutter ZX Service Manual |
A1-9 |
SPECIFICATIONS
Specifications cont.
|
|
ZX 18-52 |
ZX 19-52 |
|
Engine: |
18 hp Kohler® CV4925 |
19 hp Kawasaki OHV, FH580V |
|
High Idle |
3400 + 100 RPM |
3400 + 100 RPM |
1b |
Low Idle |
1400 RPM |
1400 RPM |
Horse Power |
18 (13.4kW) @3600 RPM |
19 HP (14.2kW) @3600 RPM |
|
|
|
|
|
|
Cubic Centimeter’s (cc’s) |
490 Displacement |
585 Displacement |
|
Fuel |
Unleaded Gasoline 87 octane min. |
Unleaded Gasoline 87 octane min. |
|
Oil Capacity |
2 qts. (1.9 L) |
1.9 qts. (1.8 L) |
|
Charge coil |
12v - 15 amp |
12v - 15 amp |
|
Construction: |
|
|
|
Front Frame |
Welded 1x2x.120” structural steel tube |
Welded 1x2x.120” structural steel tube |
|
Rear Frame |
Welded 7 & 10 ga. High strength steel |
Welded 7 & 10 ga. High strength steel |
|
Frame Assembly |
Front & rear frames bolted together. |
Front & rear frames bolted together. |
|
Deck |
Right side discharge, 52” cut, three blade |
Right side discharge, 52” cut, three blade |
|
|
mid-mounted rotary. Drawn 12 gauge |
mid-mounted rotary. Drawn 12 gauge |
|
|
steel with welded mounting brackets and |
steel with welded mounting brackets and |
|
|
gauge wheel brackets. Frame supported. |
gauge wheel brackets. Frame supported. |
|
|
|
|
|
Fuel System: |
Single fuel tank fender type mounted on |
Single fuel tank fender type mounted on |
|
|
the left side. |
the left side. |
|
Capacity |
5 Gallons (18.9 L) |
5 Gallons (18.9 L) |
|
|
Fuel tank shut off |
Fuel tank shut off |
|
|
In-line fuel fi lter |
In-line fuel fi lter |
|
Traction System: |
|
|
|
Transaxles |
Twin Hydro-Gear IZT Hydrostatic |
Twin Hydro-Gear IZT Hydrostatic |
|
|
Transaxles |
Transaxles |
|
Transaxle Drive |
Belt Drive with self-tensioning system |
Belt Drive with self-tensioning system |
|
Ground speed forward |
Infi nite, 0 to 6.5-MPH (10.5-km/hr) |
Infi nite, 0 to 6.5-MPH (10.5-km/hr) |
|
Ground speed reverse |
0 to 3.4-MPH (5.5-km/hr) |
0 to 3.4-MPH (5.5-km/hr) |
|
Transport rods |
Allows unit to be moved without engine |
Allows unit to be moved without engine |
|
|
running. |
running. |
|
Attachment Drive: |
|
|
|
Clutch |
Electric |
Electric |
|
Type |
Vertical Drive with Single Deep B-Groove |
Vertical Drive with Single Deep B-Groove |
|
|
Pulley |
Pulley |
A1-10 |
TimeCutter ZX Service Manual |
|
|
|
SPECIFICATIONS |
|
|
Specifications cont. |
|
|
|
|
|
|
|
|
|
|
|
|
|
ZX 18-52 |
ZX 19-52 |
|
|
Tires: |
|
|
|
|
|
Rear Drive Tires |
|
18x10.5-10 4 ply with “Multitrac CS” |
18x10.5-10 4 ply with “Multitrac CS” |
|
|
|
|
Tread |
Tread |
|
|
|
|
1b |
|||
Front Castor Tires |
|
410/350x4 with “sawtooth” tread |
410/350x4 with “sawtooth” tread |
||
Tire Pressure |
|
13 psi (90kPa) rear, 35 psi (241kPa) front |
13 psi (90kPa) rear, 35 psi (241kPa) front |
|
|
Electrical System: |
|
|
|
|
|
Battery voltage |
|
12 volt negative ground. |
12 volt negative ground. |
|
|
Fused |
|
(1) 30 amp blade type main. |
(1) 30 amp blade type main. |
|
|
|
|
(1) 25 amp blade type charge system. |
(1) 25 amp blade type charge system. |
|
|
|
|
(1) 10 amp included with optional light kit. |
(1) 10 amp included with optional light kit. |
|
|
Dimensions: |
|
|
|
|
|
Wheel Base |
|
52.1” (132.3cm) center of castor wheel to |
52.1” (132.3cm) center of castor wheel to |
|
|
|
|
center of drive tires. |
center of drive tires. |
|
|
Width |
|
47.6” (120.9cm) outside rear tires. |
47.6” (120.9cm) outside rear tires. |
|
|
Overall Width |
|
65” (165.1cm) with deck defl ector down. |
65” (165.1cm) with deck defl ector down. |
|
|
|
|
58” (147.3cm) Gate width with deck |
58” (147.3cm) Gate width with deck |
|
|
|
|
defl ector up. |
defl ector up. |
|
|
Overall Length |
|
77.5” (196.9cm) |
77.5” (196.9cm) |
|
|
Overall Height |
|
41” (104.1cm) |
41” (104.1cm) |
|
|
Track Width |
|
37.5” (95.3cm) center to center of rear |
37.5” (95.3cm) center to center of rear |
|
|
|
|
tires. |
tires. |
|
|
|
|
30.4” (77.2cm) center to center of castor |
30.4” (77.2cm) center to center of castor |
|
|
|
|
tires. |
tires. |
|
|
Deck Width |
|
65” (165.1cm) with defl ector down. |
66” (165.1cm) with defl ector down. |
|
|
|
|
|
|
|
|
Weight: |
|
680 lbs. (308.4kg) (estimated) |
680 lbs. (308.4kg) (estimated) |
|
|
|
|
|
|
|
|
Height of Cut: |
|
Adjusts from 1.5” to 4.5” (7 postions) |
Adjusts from 1.5” to 4.5” (7 postions) |
|
|
|
|
|
|
|
|
Tip Speed: |
|
17,500 ft/min @ 3400 RPM nominal |
17,500 ft/min @ 3400 RPM nominal |
|
|
|
|
18,070 ft/min @ 3500 RPM max |
18,070 ft/min @ 3500 RPM max |
|
|
TimeCutter ZX Service Manual |
A1-11 |
SPECIFICATIONS
Specifications cont.
|
|
ZX 18-44 |
ZX 440 |
|
Engine: |
18 hp Briggs & Stratton OHV, 31M777 |
18 hp Kohler® OHV, CV492S |
|
High Idle |
3400 + 100 RPM |
3400 + 50/- 0 RPM |
1b |
Low Idle |
1400 RPM |
1400 RPM |
Horse Power |
18 (13.4kW) @3600 RPM |
10 HP (13.4kW) @ 3600 RPM |
|
|
|
|
|
|
Cubic Centimeter’s (cc’s) |
500 Displacement |
490 Displacement |
|
Fuel |
Unleaded Gasoline 87 octane min. |
Unleaded Gasoline 87 octane min. |
|
Oil Capacity |
1.75 qts. (1.7 L) |
2 qts. (1.9 L) |
|
Charge coil |
12v - 16 amp |
12v - 15 amp |
|
Construction: |
|
|
|
Front Frame |
Welded 1x2x.120” structural steel tube |
Welded 1x2x.120” structural steel tube |
|
Rear Frame |
Welded 7 & 10 ga. High strength steel |
Welded 7 & 10 ga. High strength steel |
|
Frame Assembly |
Front & rear frames bolted together. |
Front & rear frames bolted together. |
|
Deck |
Right side discharge, 44” cut, three blade |
Right side discharge, 44” cut, three blade |
|
|
mid-mounted rotary. Drawn 13 gauge |
mid-mounted rotary. Drawn 13 gauge |
|
|
steel with welded mounting brackets and |
steel with welded mounting brackets and |
|
|
gauge wheel brackets. Frame supported. |
gauge wheel brackets. Frame supported. |
|
|
|
|
|
Fuel System: |
Single fuel tank fender type mounted on |
Single fuel tank fender type mounted on |
|
|
the left side. |
the left side. |
|
Capacity |
5 Gallons (18.9 L) |
5 Gallons (18.9 L) |
|
|
Fuel tank shut off |
Fuel tank shut off |
|
|
In-line fuel fi lter |
In-line fuel fi lter |
|
Traction System: |
|
|
|
Transaxles |
Twin Hydro-Gear IZT Hydrostatic |
Twin Hydro-Gear IZT Hydrostatic Trans- |
|
|
Transaxles |
axles with charge pumps & shock valves |
|
Transaxle Drive |
Belt Drive with self-tensioning system |
Belt Drive with self-tensioning system |
|
Ground speed forward |
Infi nite, 0 to 6.5-MPH (10.5-km/hr) |
Infi nite, 0 to 7.0-MPH (11.3-km/hr) |
|
Ground speed reverse |
0 to 3.4-MPH (5.5-km/hr) |
0 to 3.4-MPH (5.5-km/hr) |
|
Transport rods |
Allows unit to be moved without engine |
Allows unit to be moved without engine |
|
|
running. |
running. |
|
Attachment Drive: |
|
|
|
Clutch |
Electric |
Electric |
|
Type |
Vertical Drive with Single Deep B-Groove |
Vertical Drive with Single Deep B-Groove |
|
|
Pulley |
Pulley |
A1-12 |
TimeCutter ZX Service Manual |
|
|
|
SPECIFICATIONS |
|
|
Specifications cont. |
|
|
|
|
|
|
|
|
|
|
|
|
|
ZX 18-44 |
ZX 440 |
|
|
Tires: |
|
|
|
|
|
Rear Drive Tires |
|
18x7.5-8 ply with “Multitrac CS” Tread |
18x7.5-4 ply |
|
|
Front Castor Tires |
|
410/350x4 with “sawtooth” tread |
410/350x4 “sawtooth” tread |
1b |
|
Tire Pressure |
|
13 psi (90kPa) rear, 35 psi (241kPa) front |
13 psi (90kPa) rear, 35 psi (241kPa) front |
||
|
|
|
|
|
|
Electrical System: |
|
|
|
|
|
Battery voltage |
|
12 volt negative ground. |
12 volt negative ground. |
|
|
Fused |
|
(1) 30 amp blade type main. |
(1) 30 amp blade type main. |
|
|
|
|
(1) 25 amp blade type charge system. |
(1) 25 amp blade type charge system. |
|
|
|
|
(1) 10 amp included with optional light kit. |
(1) 10 amp included with optional light kit. |
|
|
Dimensions: |
|
|
|
|
|
Wheel Base |
|
52.1” (132.3cm) center of castor wheel to |
52.1” (132.3cm) center of castor wheel to |
|
|
|
|
center of drive tires. |
center of drive tires. |
|
|
Width |
|
43” (109.2cm) outside rear tires. |
43” (109.2cm) outside rear tires. |
|
|
Overall Width |
|
55” (139.7cm) with deck defl ector down. |
60” (139.7cm) with deck defl ector down |
|
|
|
|
46.6” (188.4cm) Gate width with deck |
49” (118.4cm) Gate width with deck |
|
|
|
|
defl ector up. |
defl ector up. |
|
|
Overall Length |
|
77.5” (196.9cm) |
77.5” (196.9cm) |
|
|
Overall Height |
|
40” (101.6cm) |
40” (101.6cm) |
|
|
Track Width |
|
35.2” (89.4cm) center to center of rear |
35.2” (89.4cm) center to center of rear |
|
|
|
|
tires. |
tires. |
|
|
|
|
30.4” (77.2cm) center to center of castor |
30.4” (77.2cm) center to center of castor |
|
|
|
|
tires. |
tires. |
|
|
Deck Width |
|
55” (139.7cm) with defl ector down. |
60” (139.7cm) with deck defl ector down |
|
|
|
|
|
|
|
|
Weight: |
|
635 lbs. (288 kg) (estimated) |
651 lbs. (295 kg) (estimated) |
|
|
|
|
|
|
|
|
Height of Cut: |
|
Adjusts from 1.5” to 4.5” (7 postions) |
Adjusts from 1.5” to 4.5” (7 postions) |
|
|
|
|
|
|
|
|
Tip Speed: |
|
18,160 ft/min @ 3400 RPM nominal |
18,160 ft/min @ 3400 RPM nominal |
|
|
|
|
18,770 ft/min @ 3500 RPM max |
18,770 ft/min @ 3500 RPM max |
|
|
TimeCutter ZX Service Manual |
A1-13 |
SPECIFICATIONS
Specifications cont.
|
|
ZX 480 |
ZX 525 |
|
Engine: |
Briggs & Stratton Intek OHV, 441577 |
Kawasaki FH58V OHV |
|
High Idle |
3400 + 100 RPM |
3400 + 100 RPM |
1b |
Low Idle |
N/A |
1400 RPM |
Horse Power |
N/A |
N/A |
|
|
|
|
|
|
Cubic Centimeter’s (cc’s) |
725 Dispacement |
585 Dispacement |
|
Fuel |
Unleaded Gasoline 87 octane min. |
Unleaded Gasoline 87 octane min. |
|
Oil Capacity |
2 qts. (1.9 L) |
1.9 qts. (1.8 L) |
|
Charge coil |
12v - 16 amp |
12v - 13 amp |
|
Construction: |
|
|
|
Front Frame |
Welded 1x2x.120” structural steel tube |
Welded 1x2x.120” structural steel tube |
|
Rear Frame |
Welded 7 & 10 ga. High strength steel |
Welded 7 & 10 ga. High strength steel |
|
Frame Assembly |
Front & rear frames bolted together. |
Front & rear frames bolted together. |
|
Deck |
Right side discharge, 48” cut, three |
Right side discharge, 44” cut, three blade |
|
|
blade mid-mounted rotary. Drawn 12 |
mid-mounted rotary. Drawn 12 gauge |
|
|
gauge steel deck with gauge reinforced |
steel with welded mounting brackets and |
|
|
plate and welded mounting brackets and |
gauge wheel brackets. Frame supported. |
|
|
gauge. |
|
|
|
|
|
|
Fuel System: |
Single fuel tank fender type mounted on |
Single fuel tank fender type mounted on |
|
|
the left side. |
the left side. |
|
Capacity |
5 Gallons (18.9 L) |
5 Gallons (18.9 L) |
|
|
Fuel tank shut off |
Fuel tank shut off |
|
|
In-line fuel fi lter |
In-line fuel fi lter |
|
Traction System: |
|
|
|
Transaxles |
Twin Hydro-Gear IZT Hydrostatic Trans- |
Twin Hydro-Gear IZT Hydrostatic Trans- |
|
|
axles with charge pumps & shock valves. |
axles with charge pumps & shock valves. |
|
Transaxle Drive |
Belt Drive with self-tensioning system |
Belt Drive with self-tensioning system |
|
Ground speed forward |
Infi nite, 0 to 7.0-MPH (11.3-km/hr) |
Infi nite, 0 to 7.0-MPH (11.3-km/hr) |
|
Ground speed reverse |
0 to 3.4-MPH (5.5-km/hr) |
0 to 3.4-MPH (5.5-km/hr) |
|
Transport rods |
Allows unit to be moved without engine |
Allows unit to be moved without engine |
|
|
running. |
running. |
|
Attachment Drive: |
|
|
|
Clutch |
Electric |
Electric |
|
Type |
Vertical Drive with Single Deep B-Groove |
Vertical Drive with Single Deep B-Groove |
|
|
Pulley |
Pulley |
A1-14 |
TimeCutter ZX Service Manual |
|
|
|
SPECIFICATIONS |
|
|
Specifications cont. |
|
|
|
|
|
|
|
|
|
|
|
|
|
ZX 480 |
ZX 525 |
|
|
Tires: |
|
|
|
|
|
Rear Drive Tires |
|
18x10.5-4 ply |
18x10.5-10 4 ply with “Multitrac CS” |
|
|
|
|
|
Tread |
|
|
|
|
|
1b |
||
Front Castor Tires |
|
410/350x4 with “sawtooth” tread |
410/350x4 with “sawtooth” tread |
||
Tire Pressure |
|
13 psi (90kPa) rear, 35 psi (241kPa) front |
13 psi (90kPa) rear, 35 psi (241kPa) front |
|
|
Electrical System: |
|
|
|
|
|
Battery voltage |
|
12 volt negative ground. |
12 volt negative ground. |
|
|
Fused |
|
(1) 30 amp blade type main. |
(1) 30 amp blade type main. |
|
|
|
|
(1) 25 amp blade type charge system. |
(1) 25 amp blade type charge system. |
|
|
|
|
(1) 25 amp blade type charge system. |
(1) 10 amp (blade type) included with |
|
|
|
|
|
optional light kit. |
|
|
Dimensions: |
|
|
|
|
|
Wheel Base |
|
52.1” (132.3cm) center of castor wheel to |
52.1” (132.3cm) center of castor wheel to |
|
|
|
|
center of drive tires. |
center of drive tires. |
|
|
Width |
|
43” (109.2cm) outside rear tires. |
47.6” (120.9cm) outside rear tires. |
|
|
Overall Width |
|
62.5” (158.8cm) with deck defl ector |
68” (165.1cm) with deck defl ector down. |
|
|
|
|
down. |
55” (147.3cm) Gate width with deck |
|
|
|
|
53.5” (135.9cm) Gate width with deck |
defl ector up. |
|
|
|
|
defl ector up. |
|
|
|
Overall Length |
|
77.5” (196.9cm) |
77.5” (196.9cm) |
|
|
Overall Height |
|
40” (101.6cm) |
41” (101.6cm) |
|
|
Track Width |
|
35.2” (89.4cm) center to center of rear |
37.5in. (95.3cm) center to center of rear |
|
|
|
|
tires. |
tires. |
|
|
|
|
30.4” (77.2cm) center to center of castor |
30.4” (77.2cm) center to center of castor |
|
|
|
|
tires. |
tires. |
|
|
Deck Width |
|
62.5” (158.8cm) with defl ector down. |
68” (165.1cm) with defl ector down. |
|
|
|
|
|
|
|
|
Weight: |
|
646 lbs. (293 kg) (estimated) |
695 lbs. (315 kg) (estimated) |
|
|
|
|
|
|
|
|
Height of Cut: |
|
Adjusts from 1.5” to 4.5” (7 postions) |
Adjusts from 1.5” to 4.5” (7 postions) |
|
|
|
|
|
|
|
|
Tip Speed: |
|
15,710 ft/min @ 3400 RPM nominal |
17,500 ft/min @ 3400 RPM nominal |
|
|
|
|
16,170 ft/min @ 3400 RPM nominal |
18,070 ft/min @ 3500 RPM max |
|
|
TimeCutter ZX Service Manual |
A1-15 |
SPECIFICATIONS
Bolt Torques
|
|
|
|
|
|
|
|
|
|
|
Description |
Torque - 52” |
Torque - 44” |
|
|
||
|
|
|
|
|
|
|
|
|
|
|
Blade to Spindle |
80 - 100 ft·lb (109 - 136 N·m) |
40 |
- 60 ft·lb (54 |
- 82 N·m) |
|
|
|
|
|
|
|
|
|
|
|
|
|
Caster Bolts |
77 |
- 95 ft·lb (105 - 130 N·m) |
77 |
- 95 ft·lb (105 - 130 N·m) |
|
|
|
|
|
|
|
|
|
|
|
|
|
Clutch Bolt |
50 |
- 60 ft·lb (68 - 82 N·m) |
50 |
- 60 ft·lb (68 |
- 82 N·m) |
|
1b |
|
Engine Mounting Bolts |
120 - 180 ft·lb (164 - 246 N·m) |
120 - 180 ft·lb (164 - 246 N·m) |
|
|||
|
Spindle Pulley Nuts |
80 - 100 ft·lb (109 - 136 N·m) |
50 |
- 75 ft·lb (68 |
- 102 N·m) |
|
||
|
|
|
||||||
|
|
|||||||
|
|
|
|
|
|
|
|
|
|
|
Wheel Lug Nuts |
70 |
- 90 ft·lb (95.5 - 123 N·m) |
70 |
- 90 ft·lb (95.5 - 123 N·m) |
|
|
|
|
|
|
|
|
|
|
|
1 - 6 |
TimeCutter™ Z Service Manual |
|
|
|
MAINTENANCE |
|
|
Maintenance Schedule (Z16-44) |
|
|
|
||
|
|
Maintenance Procedure |
Service Interval |
|
|
|
|
|
|
|
|
|
Change the engine oil |
After first use |
|
|
|
|
Check the engine oil level |
|
|
|
|
|
Check the safety system |
Each use |
|
|
|
|
|
|
|
|
|
|
Clean the mower housing |
|
|
|
|
|
|
1c |
|||
|
|
|
|
|
|
|
Check the cutting blades |
Every 5 hours |
|
||
|
|
|
|||
|
Grease all lubrication points1 |
|
|
|
|
|
Oil the linkage bushings1 |
|
|
|
|
|
Service the foam air cleaner1 |
Every 25 hours |
|
|
|
|
Check the belts for wear/cracks |
|
|
||
|
|
|
|
||
|
|
|
|
|
|
|
Check the battery electrolyte |
|
|
|
|
|
|
|
|
|
|
|
Check the tire pressure |
|
|
|
|
|
|
|
|
|
|
|
Change the engine oil2 |
Every 50 hours |
|
|
|
|
Clean the cooling system1 |
|
|
|
|
|
Service the paper air cleaner1 |
|
|
|
|
|
Change the oil filter2 |
Every 100 hours |
|
|
|
|
Replace the fuel filter |
|
|
|
|
|
|
|
|
|
|
|
Replace the spark plug(s) |
|
|
|
|
|
|
|
|
|
|
|
Before Storage: |
|
|
|
|
|
• |
Perform all maintenance procedures listed above. |
|
|
|
|
• |
Drain the fuel tank. |
|
|
|
|
• |
Charge the battery and disconnect the battery cables. |
|
|
|
|
• |
Paint any chipped surfaces. |
|
|
|
|
|
|
|
|
|
1More often in dusty, dirty conditions
2More often when operating the engine under heavy load or in high temperatures
IMPORTANT: Refer to your engine operator’s manual for additional maintenance procedures.
CAUTION
If you leave the key in the ignition switch, someone could accidently start the engine and seriously injury you or other bystanders.
Remove the key from the ignition and disconnect the wire from the spark plug(s) before you do any maintenance. Set the wire aside so that it does not accidentally contact the spark plug.
TimeCutter™ Z Service Manual |
1 - 7 |
MAINTENANCE
Maintenance Schedule (Z17-44 & Z17-52)
|
|
|
|
|
|
|
|
|
Maintenance Procedure |
Service Interval |
|
|
|
|
|
|
|
|
|
Check the engine oil level |
|
|
|
|
|
Check the safety system |
Each use |
|
|
|
|
|
|
|
|
|
|
Clean the cooling system1 |
|
||
|
|
|
|
||
|
|
Clean the mower housing |
|
|
|
1c |
|
|
|||
|
|
|
|
||
|
Check the air cleaner |
|
|
||
|
|
Check the cutting blades |
Every 5 hours |
|
|
|
|
Grease all lubrication points1 |
|
|
|
|
|
Oil the linkage bushings1 |
|
|
|
|
|
Service the foam air cleaner1 |
Every 25 hours |
|
|
|
|
Check the belts for wear/cracks |
|
||
|
|
|
|
||
|
|
|
|
|
|
|
|
Check the battery electrolyte |
|
|
|
|
|
|
|
|
|
|
|
Check the tire pressure |
|
|
|
|
|
|
|
|
|
|
|
Change the engine oil1 |
Every 100 hours |
|
|
|
|
Replace the paper air cleaner1 |
|
||
|
|
|
|
||
|
|
Change the oil filter1 |
|
|
|
|
|
Replace the fuel filter |
Every 200 hours |
|
|
|
|
|
|
|
|
|
|
Check the spark plug(s) |
|
|
|
|
|
|
|
|
|
|
|
Before Storage: |
|
|
|
|
|
• |
Perform all maintenance procedures listed above. |
|
|
|
|
• |
Drain the fuel tank. |
|
|
|
|
• |
Charge the battery and disconnect the battery cables. |
|
|
|
|
• |
Paint any chipped surfaces. |
|
|
|
|
|
|
|
|
1More often in dusty, dirty conditions
IMPORTANT: Refer to your engine operator’s manual for additional maintenance procedures.
CAUTION
If you leave the key in the ignition switch, someone could accidently start the engine and seriously injury you or other bystanders.
Remove the key from the ignition and disconnect the wire from the spark plug(s) before you do any maintenance. Set the wire aside so that it does not accidentally contact the spark plug.
1 - 8 |
TimeCutter™ Z Service Manual |
|
|
|
MAINTENANCE |
||
Maintenance Schedule (Z18-52) |
|
|
|
||
|
|
Maintenance Procedure |
Service Interval |
|
|
|
|
|
|
|
|
|
Change the engine oil |
After first use |
|
|
|
|
Check the engine oil level |
|
|
|
|
|
Check the safety system |
Each use |
|
|
|
|
|
|
|
|
|
|
Clean the air intake screen |
|
|
||
|
|
|
1c |
||
|
|
|
|
|
|
|
Clean the mower housing |
|
|
||
|
|
|
|
||
|
Check the cutting blades |
Every 5 hours |
|
|
|
|
Grease all lubrication points1 |
|
|
|
|
|
Oil the linkage bushings1 |
|
|
|
|
|
Service the foam air cleaner1 |
Every 25 hours |
|
|
|
|
Check the belts for wear/cracks |
|
|
||
|
|
|
|
||
|
|
|
|
|
|
|
Check the battery electrolyte |
|
|
|
|
|
|
|
|
|
|
|
Check the tire pressure |
|
|
|
|
|
|
|
|
|
|
|
Service the paper air cleaner1 |
Every 50 hours |
|
|
|
|
Change the engine oil |
Every 100 hours |
|
|
|
|
Check the spark plug(s) |
|
|
||
|
|
|
|
||
|
|
|
|
|
|
|
Change the oil filter |
|
|
|
|
|
Replace the fuel filter |
Every 200 hours |
|
|
|
|
|
|
|
|
|
|
Replace the paper air cleaner1 |
|
|
|
|
|
Clean the engine shrouds and cooling fins1 |
Every 300 hours |
|
|
|
|
Before Storage: |
|
|
|
|
|
• |
Perform all maintenance procedures listed above. |
|
|
|
|
• |
Drain the fuel tank. |
|
|
|
|
• |
Charge the battery and disconnect the battery cables. |
|
|
|
|
• |
Paint any chipped surfaces. |
|
|
|
|
|
|
|
|
|
1More often in dusty, dirty conditions
IMPORTANT: Refer to your engine operator’s manual for additional maintenance procedures.
CAUTION
If you leave the key in the ignition switch, someone could accidently start the engine and seriously injury you or other bystanders.
Remove the key from the ignition and disconnect the wire from the spark plug(s) before you do any maintenance. Set the wire aside so that it does not accidentally contact the spark plug.
TimeCutter™ Z Service Manual |
1 - 9 |
THIS PAGE INTENTIONALLY LEFT BLANK
1 - 10 |
TimeCutter™ Z Service Manual |
MODEL/SERIAL NUMBER LOCATION
QUICK REFERENCE SECTION
Safety Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1a
1b
1c
SERVICE SECTION
Model/Serial Number . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Greasing and Lubrication. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Transaxle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Chassis . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Mower Decks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Electrical Systems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2
3
4
5
6
7
8
TimeCutter™ Z Service Manual |
2 - 1 |
MODEL/SERIAL NUMBER LOCATION
Table of Contents
MODEL/SERIAL NUMBER LOCATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 - 3
2 - 2 |
TimeCutter™ Z Service Manual |
MODEL/SERIAL NUMBER LOCATION
The unit model and serial number plate is on the frame under the seat as shown in the illustration.
The engine has its own model and serial number identification. Consult the appropriate engine manufacturer’s service literature for the location and translation of the engine model and serial number information.
0702-0201
|
Transaxles also have their own model/serial |
2 |
|
number. |
|
|
||
|
|
|
|
|
|
|
|
|
|
|
|
0702-0202
TimeCutter™ Z Service Manual |
2 - 3 |
THIS PAGE INTENTIONALLY LEFT BLANK
2 - 4 |
TimeCutter™ Z Service Manual |
GREASING AND LUBRICATION
QUICK REFERENCE SECTION
Safety Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1a
1b
1c
SERVICE SECTION
Model/Serial Number . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Greasing and Lubrication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Transaxle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Chassis . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Mower Decks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Electrical Systems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2
3
4
5
6
7
8
TimeCutter™ Z Service Manual |
3 - 1 |
GREASING AND LUBRICATION
Table of Contents
Service Interval/Specification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 - 3
Lubrication Points . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 - 4
3 - 2 |
TimeCutter™ Z Service Manual |