Toro 74534, 74534TE, 74536, 74536TE, 74538 Setup Instructions

...
0 (0)

Form No. 3360-902 Rev C

GrandStandMowers

Model No. All GrandStand Mowers

Setup Instructions

Loose Parts

Use the chart below to verify that all parts have been shipped.

Procedure

Description

Qty.

Use

 

 

 

 

1

No parts required

Check the tire pressure.

 

 

 

2

No parts required

Prepare the grass deflector.

 

 

 

3

No parts required

Check the engine oil level.

 

 

 

4

No parts required

Add fuel to the machine.

 

 

 

5

No parts required

Check the hydraulic oil level.

 

 

 

6

No parts required

Install the battery cables.

 

 

 

7

No parts required

Charge the battery.

 

 

 

8

No parts required

Check the machine before delivery to

the customer.

 

 

 

Operator’s Manual

1

 

 

Engine Owner’s Manual

1

 

9

Registration Card

1

Delivering the machine to the customer.

Operator training material

1

 

 

Key

1

 

 

Oil drain hose

1

 

© 2008—The Toro® Company

Register at www.Toro.com.

Original Instructions (EN)

8111 Lyndale Avenue South

 

Printed in the USA.

Bloomington, MN 55420

 

All Rights Reserved

1

Checking the Tire Pressure

No Parts Required

Procedure

Pressure: 12 to 14 psi (83 to 97 kPa)

Note: The front caster wheel is a semi-pneumatic tire and does not need to be checked.

Check the air pressure in the drive tires.

Figure 1

3

Checking the Engine Oil Level

No Parts Required

Procedure

Before you start the engine and use the machine, check the oil level in the engine crankcase; refer to Checking the Engine Oil Level in the Operator’s Manual.

4

Adding Fuel to the Machine

No Parts Required

Procedure

Add gasoline to the machine before starting it. Refer

to your Operator’s Manual. for the correct fuel and procedure. Ensure the fuel shut-off valve is open before attempting to start the engine.

2

Preparing the Grass Deflector

No Parts Required

Procedure

Install the spring for the grass deflector; refer to Replacing the Grass Deflector in the Operator’s Manual.

5

Checking the Hydraulic Oil Level for Mowers with Hydro Drive

No Parts Required

Procedure

Before you start the engine and use the machine, check the hydraulic oil level in the tank; refer to Checking the Hydraulic Oil Level in the Operator’s Manual.

2

Toro 74534, 74534TE, 74536, 74536TE, 74538 Setup Instructions

6

Installing the Battery Cables

No Parts Required

Procedure

1.If not installed, install the positive (red) battery cable to the positive (+) battery terminal with a nut, washer and bolt. Slide the rubber cover over the post.

2.Then install the negative battery cable to the negative (-) battery terminal with a nut, washer and bolt.

Figure 2

1.

Negative battery cable

4.

Install the battery cables

 

 

 

like this for 48, 52 and 60

 

 

 

inch mowers

2.

Positive battery cable

5.

The battery cables cross

 

 

 

when installed correctly for

 

 

 

36 and 40 inch Mowers

3.Battery

7

Charging the Battery

No Parts Required

Procedure

Charging the battery produces gasses that can explode and cause serious injury.

Keep cigarettes, sparks and flames away from the battery.

Make sure the ignition switch is off.

Ventilate when charging or using the battery in an enclosed space.

Important: Do not run the machine with the battery disconnected; electrical damage may occur to the engine.

Charge the battery. Refer to the Operator’s Manual for instructions.

Figure 3

3

Loading...
+ 5 hidden pages