TOA Electronics WM-4220, WM-4210 User Manual

70.82 Kb

OPERATING INSTRUCTIONS

UHF WIRELESS MICROPHONE

WM-4210

 

WM-4220

Please follow the instructions in this manual to obtain the optimum results from this unit. We also recommend that you keep this manual handy for future reference.

1. SAFETY PRECAUTIONS

Be sure to read the instructions in this section carefully before use.

Make sure to observe the instructions in this manual as the conventions of safety symbols and messages regarded as very important precautions are included.

We also recommend you keep this instruction manual handy for future reference.

Safety Symbol and Message Conventions

Safety symbols and messages described below are used in this manual to prevent bodily injury and property damage which could result from mishandling. Before operating your product, read this manual first and understand the safety symbols and messages so you are thoroughly aware of the potential safety hazards.

WARNING

CAUTION

Indicates a potentially hazardous situation which, if mishandled, could result in death or serious personal injury.

Indicates a potentially hazardous situation which, if mishandled, could result in moderate or minor personal injury, and/or property damage.

WARNING

To prevent the electromagnetic wave from badly influencing medical equipment, make sure to switch off the unit's power when placing it in close proximity to the medical equipment.

CAUTION

When the unit is not in use for 10 days or more, be sure to take the battery out of the unit because battery leakage may cause personal injury or contamination of environment.

Make sure to observe the following handling precautions so that a fire or personal injury does not result from leakage or explosion of the battery.

·Do not short, disassemble, heat nor put the battery into a fire.

·Never charge batteries of the type which are not rechargeable.

·Do not solder a battery directly.

·Be sure to use the specified type of battery.

·Note correct polarity (positive and negative orientation) when inserting a battery in the unit.

·Avoid locations exposed to the direct sunlight, high temperature and high humidity when storing batteries.

2. GENERAL DESCRIPTION

The WM-4210 Wireless Microphone employs a dynamic microphone element and is suitable for vocal applications.

The WM-4220 Wireless Microphone employs an electret condenser microphone element and is suitable for speech applications.

3. FEATURES

One frequency can be selected from 16 operating frequencies of 690 – 865 MHz.

An optimized PLL-synthesizer minimizes the oscillation frequency drift resulting from the ambient temperature or voltage fluctuation.

Battery lamp indicates battery consumption to prevent the unit from malfunctioning when the battery level remarkably decreases.

4. HANDLING PRECAUTIONS

Do not expose the unit to rain or an environment where it may be splashed by water or other liquids, as doing so may result in unit failure.

Never open nor remove the unit case to modify the unit. Refer all servicing to your nearest TOA dealer.

Take care not to drop the unit onto the floor nor bump it against a hard object as the unit could fail.

Do not place the unit in locations of high temperature (ex. in a car parked in summer) or high humidity as the unit could fail.

Do not use the unit in locations where it is exposed to seawater.

To clean, use a dry cloth. When the unit gets very dirty, wipe lightly with a cloth damped in a dilute neutral cleanser, then wipe with a dry cloth. Never use benzine, thinner, or chemically-treated cleaning towel.

Avoid using a mobile telephone near the wireless microphone in use. Noise could be picked up.

5. NOMENCLATURE

[WM-4210]

[WM-4220]

Power/Battery lamp (Orange LED)

Power ON/OFF switch

Channel select switch

Battery clip

6. BATTERY INSERTION

Step 1.

Hold the microphone body and rotate the microphone

 

 

grip counterclockwise to remove it.

 

Step 2.

Insert the battery 6LR61 (Alkaline 9 V) according to

 

 

the instructions attached to the inside of the battery

 

 

compartment. Pay attention to the correct polarity

 

 

when inserting the battery.

 

Step 3.

Replace the microphone grip by sliding and rotating it

1

 

clockwise.

 

Battery replacement

A brand-new battery will provide the power enough to operate the unit continuously for 10 hours.

As long as the battery has sufficient power for the microphone to function properly, the orange LED will light. When the orange LED starts to fade and then flash, replace it with a new one.

2

Orange LED

Indicates the battery level by lighting or flashing.

7. OPERATION

Step 1. Make sure that the receiver and the wireless microphone are of the same channel (frequency).

Step 2. If they are not identical in channel, you have to adjust the channel switch.

Step 3. Place the microphone ON/OFF switch in the ON position.

The orange LED indicates the circuit is active.

Step 4. Make sure to shift the ON/OFF switch back to the OFF position after using the wireless microphone.

8. OPERATIONAL HINTS

The microphone's service distance is 3 – 120 m. When the microphone user moves in a facility, signal dropouts (momentary losses of signal reception) may be encountered. These dropouts are caused by the building's architectural designs or materials which block the travel of or reflect the radio signal. If this occurs, the user needs to change locations for better signal reception.

The proper operation of your wireless system may be interfered with by other system operating on the same frequency. In such cases, change the operating frequency of your system. (As to dealing with the interference, refer to the operating instructions of the wireless tuner.)

Should you have any questions regarding the use or availability of TOA wireless products, please contact your local TOA dealer.

9. CHANNEL NUMBER SETTING

Step 1. Switch off the power. Rotate the microphone grip counterclockwise to remove it.

Step 2. Using the supplied screwdriver, set the Channel setting switch pointer to the desired channel number.

Step 3. Replace the microphone grip.

Note: Make sure that the wireless microphone is identical to the wireless tuner in the channel number. Should the microphone's setting differ from that of the tuner, the tuner does not receive the microphone signal.

10. SPECIFICATIONS

Model No.

WM-4210

 

WM-4220

Microphone Element

Dynamic type

 

Electret condenser type

 

Cardioid pattern

 

Cardioid pattern

 

 

 

 

Emission

 

F3E

 

 

 

Frequency Range

690 – 865 MHz, UHF

 

 

 

 

Selectable Channel

 

16 channels

 

 

 

 

RF Carrier Power

 

Less than 50 mW

 

 

 

 

Tone Frequency

 

32.768 kHz

 

 

 

 

Maximum Input Level

130 dB SPL

 

125 dB SPL

 

 

 

 

Maximum Deviation

 

±40 kHz

 

 

 

 

Audio Frequency Response

100 – 12,000 Hz

 

200 – 12,000 Hz

 

 

 

Dynamic Range (AF Circuit)

More than 100 dB (with WT-4810)

 

 

 

 

Battery

 

6LR61 (9 V x 1)

 

 

 

Battery Life

More than 10 hours (alkaline)

 

 

 

Indicator

Power/Battery lamp (orange LED)

 

 

 

 

Antenna

 

Built-in type

 

 

 

 

Operating Temperature

 

–10 to +50°C

 

 

 

Finish

Resin, coating, dark gray

 

 

 

 

Dimensions

ø50 x 235.2 mm

 

ø45 x 235.2 mm

 

 

 

 

Weight

270 g (with battery)

 

250 g (with battery)

 

 

 

 

Note: The design and specifications are subject to change without notice for improvement.

• Accessories

 

Microphone holder (with stand adapter) ...............

1

Screwdriver (for setting) .......................................

1

Storage case ........................................................

1

License requirement

Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Printed in Taiwan 133-07-180-90