TOA Electronics EXES 6000 CP-63 User Manual

3.32 Mb

EXES-6000 CP-63

For

INTERCOM SYSTEM

TOA EXES-6OOO INTERCOM SYSTEM

Central Processing Unit for Tie-line System

CP-63

INSTALLATION HAND BOOK

TOA ELECTRICCO.,LTD.

KOBE, JAPAN

133-21-081-1

CONTENTS

 

 

 

 

 

 

 

 

 

Page

 

INTRODUCTION TO THE INSTALLATION MANUAL FOR EXES-6000

 

2

 

FUNCTIONS WHICH REQUIRE ADDITIONAL UNITS

 

 

3

 

TIE-LINE CONNECTION OF THE EXCHANGES

 

 

 

5

 

WIRING FOR TIE-LINE CONNECTION OF THE

EXCHANGES

 

8

 

 

 

PART 1. OPERATING

OF CP UNIT AND

NO. 200 PROGRAMMING

 

1.

Precautions for Installation of CP-63

 

 

 

 

11

2.

Initial CP 63 set up

 

 

 

 

 

12

3.

Trouble Shooting

 

 

 

 

 

13

4.

CP-63 DIP Switches for Function Selection

 

 

 

 

16

5.

Dip Switch Selection and Station No. 200 Programming for Each

Function

 

17

6.

Function Code Table for Station No. 200 Programming

 

 

18

7.

Station No. 200 Programming for Each Function

 

 

 

21

[Function Group A]

 

 

 

 

FUNCTION

CODE

 

7-1

Executive Priority (Highest Priority)

 

 

 

50

21

 

7-2

Continuous Calling Tone

 

 

 

51

22

 

7-3

Stations Allowed Access to All Call

 

 

 

52

23

 

7-4

Stations Allowed Access to Conference

 

 

53

24

 

7-5

Automatic Access to Paging

 

 

 

54

25

 

7-6

Stations Allowed Access to One-shot Make Output

 

56

27

 

7-7

Stations Allowed Access to Make/Break Output

 

57

28

 

7-8

Stations Allowed Access to 8 Selectable or Decimal Output

58

29

 

7-9

Stations Allowed Access to 4 Decimal Digits Output

 

59

30

[Function Group B]

 

 

 

 

 

 

 

7-10

Secretary Transfer

 

 

 

60

31

 

7-11

Master/Sub Relationship

 

 

 

61

32

 

7-12

Group Hunting

 

 

 

62

33

[Function Group C]

 

 

 

 

 

 

 

7-13

Paging Zone

 

 

 

 

70

34

 

7-14

Group Blocking 1: Establishment of each Group

 

71

35

 

7-15

Calling Party Indication (Lamp Type)

 

 

72

36

[Function Group D]

 

 

 

 

 

 

 

7-16

Group Blocking 2: Allowing Calls among Groups

 

81

37

 

7-17

Group Blocking 3: Allowing Group Access to Paging

 

82

38

[Function Group E]

 

 

 

 

 

 

 

7-18

Programmable Station Numbering

 

 

 

90

39

8.

Programming Data Table

 

 

 

 

41

 

Initial Programming

 

 

 

 

41

 

Function Table for the System

 

 

 

 

42

 

Function Table for Stations (1)

 

 

 

 

43

 

Function Table for Stations (2)

 

 

 

 

44

 

Function Table for Stations (3)

 

 

 

 

45

 

Paging Zone Table

 

 

 

 

46

 

Station Numbers Table for Calling Party

Indication (Lamp Type)

 

46

 

Tables for Group Blocking (3 Tables)

 

 

 

 

46

 

 

PART 2. FUNCTION SELECTION

FOR DATA TRANSMITTING AND

RECEIVING

UNITS

9. Setting of Channel Select Switch of Transmitting Unit (DT-E11)

 

 

 

 

and Word Select Switch of Receiving Unit (DR-B61)

 

 

 

49

10.

DIP Switch Table for Data Transmitting and Receiving Units

 

 

50

11.

System Diagram of Data Transmitting and Receiving Units

 

 

51

12.

Explanation of Data Transmitting Unit Output Channels

 

 

52

13.

Explanation of Data

Receiving Unit Output Data

 

 

 

53

 

13-1

CH-0

IN-OUT Annunciation (500 Contacts)

 

 

 

53

 

13-2

CH-1

(1)

One-Shot Make Output (50 Contacts)

 

 

54

 

 

 

(2)

Make/Break Output (100 Contacts)

 

 

54

 

 

 

(3)

8-Selectable Make Output (9 Units)

 

 

54

 

 

 

(4)

Decimal Output (9 Units)

 

 

 

54

 

 

 

(5)

4 Decimal Digits Output (9 Units)

 

 

54

 

 

 

(6)

Pager Control Output (64 Contacts)

 

 

54

 

13-3

CH-2

Calling Party Indication (Lamp Type)

(1)

 

 

55

 

13-4

CH-3

Calling Party Indication (Lamp Type)

(2)

 

 

56

Appendix. Instructions for building the CP-63 in the EXES-5000

 

 

57

— 1 —

INTRODUCTION TO THE INSTALLATION MANUAL FOR EXES-6000

This manual forms part of the Installation Manual for TOA INTERCOM SYSTEM EXES-6000.

You may add the CP-63 to your TOA INTERCOM SYSTEM EXES6000, according to your specific needs, to obtain various other functions. Correct operation of these additional functions is not performed by simply connecting the additional equipments/devices. Provision of such additional function requires the following:

(1)Connection of the additional equipment, as required.

(2)Selection of functions which satisfy your needs and setting up these functions in the respective equipment.

For (1) Connections of Equipment, etc., refer to "

Installation

Handbook of Model EX-610/620 EXCHANGE" or

Operation

Manual of Data Transmitting and Receiving Units", etc.

 

This "Installation Handbook of CP-63" deals principally with (2) Selection of functions and setting up of respective equipment.

This Handbook also explains the connection method for the EXES6000 Tie-line System using the CP-63 and the TI-62 units.

There are certain minimum installation requirements to be met even through you may not need many additional functions or additonal equipment, it is still necessary to read "2. Initial CP-63 Set Up (Page 12)". When you may use only some of the additional functions or equipments, it is not necessary to read instructions on unrequired functions. Make sure, however, that careful study of the necessary parts of this booklet should be done before proceeding further.

INSTALLATION HAND BOOK OF EXES-6000

EXES-6000

EX-610/620 INSTALLATION HAND BOOK OF EXCHANGE 133-21-100-9

EXES-6000 CP-63 INSTALLATION HAND BOOK 133-21-081-1 (This Hand Book)

EXES-6000 CP-63 INITIAL CHECKING SHEET FOR THE SYSTEM 133-21-085-5

Manuals Necessary for Installation of Exchange

DATA TRANSMITTING AND RECEIVING UNIT "DT-E11 OPERATION MANUAL" 133-05-094-1A "DR-B61 OPERATION MANUAL" 133-05-095-0

REQUIRED INSTALLATION HAND BOOK

SYSTEMS OF

EXES-6000

Normal Conversation

and Paging System

Normal Conversation and Paging System with Display and Control Functions

Tie-line System with Normal Conversation and Paging Functions

Tie-line System with Normal Conversation, Paging, Display

and Control Functions

EX-610/620

CP-62

CP-62

CP-63

CP-63

DATA TRANSMITTING

INSTALLATION

INSTALLATION

INITIAL

INSTALLATION

INITIAL

AND RECEIVING UNIT

HAND BOOK

HAND BOOK

CHECKING

HAND BOOK

CHECKING

OPERATION MANUAL

OF EXCHANGE

 

SHEET

 

SHEET

 

— 2 —

FUNCTIONS WHICH REQUIRE ADDITIONAL UNITS

Those functions of the CP-63 which require either the addition of specific units or processing in existing units are as mentioned below. Before installation and adjustment of equipment, make sure to check your system.

(For Data Transmitting and Receiving units, refer to Part 2. "Function Selection for Data Transmitting and Receiving units" Page 49.)

Function

Additional Equipment

Unit Model

Required

Number

 

TalkBack from

Talk-Back Unit

TK-12

paging speaker

 

 

Conference

Conference Unit

CL-62

Remarks

Not yet available for sale.

Build this unit in all exchanges connected by tie-line. It is not possible to originate a conference from a station connected to the exchange without the CL unit but possible to participate in the conference from that station.

External PA Paging

Paging Interface Unit

PI-62

Station Paging

Paging Interface Unit

PI-62

 

Data Transmitting Unit

DT-E11

Indication and

 

 

Control

 

 

 

Data Receiving Unit

DR-B61

Tie-line System

Tie-line Interface Unit

TI-62

External PA Equipment is required.

1.Wiring of "Station Paging Assignment" located at the back of the frame of the Exchange.

2.Cutting of LM-62 jumper wire to split station paging system.

The number that can be mounted on the cabinet-mount type exchange is one (1). Use the connection cable YR-806.

When more than 2 pieces are mounted, we suggest you use rack-mount type exchange. For connection between the exchange and the DT-E11, use the YR-802, and the YR-803 for extension of the DT-E11 .

Such devices as indicator, control unit etc. can be made by using this unit and 24V DC power supply.

Insert this unit into a slot intended for the PI unit No. 2 (Zone No. 8-15).

— 3 —

Example of Exchange Mounted on Intercom Cabinet Rack

(For Tie-line System Including All-Call Paging and 7 Individual Zone Paging unit and one Data Transmitting unit)

Exchange EX-620 (for 128 stations)

Exchange EX-610 (for 64 stations)

Central Processing Unit CP-63

Output Control Unit OC-62

Highway Control Unit HC-62

Signal Generating and Distributing Unit SG-62

Conference Link Unit CL-62 (In this location, DL-62 is also mountable.)

Duplex Link Unit DL-62

Line Modem Unit LM-62

Paging Interface Unit PI-62 (In this location, LM-62 is also mountable.) (Zone 0-7 with All-Call Paging)

Tie-line Interface Unit TI-62

Perforated Panel PF-022G *

Data Transmitting Unit DT-E11 (In the standard system, Perforated Panel PF-012G should come in this position.)*

Junction Cable YR-806 (Cable length: 1000mm) (YR-802 (Cable length: 400mm) is not available.)

Note.*

The Exchange Cabinet Rack CR-610 or CR-620 includes Perforated Panels PF-012G and PF-022G.

Power Supply Unit DS-620

Power Switch

AC Fuse

DC Fuse

Battery Fuse

Exchange Cabinet Rack CR-620

Exchange Frame FR-620

Power Supply Unit DS-610

Power Indication Lamp

Battery Power Indication Lamp

Buzzer Stop Switch

Exchange Cabinet Rack CR-610

Exchange Frame FR-610

— 4 —

TIE-LINE CONNECTION OF THE EXCHANGES

1. Function of the Central Processing Unit CP-63

To make communications between exchanges possible in the EXES6000 system, the CP-63 and the Tie-line Interface Unit TI-62 are required in addition to the exchange EX-610 or the EX-620.

The TI-62 is the interface unit for transmitting and receiving audio signals and dial data signals between the exchanges.

After receiving dial signals from the station, the CP-63 transmits the dial data signals to the TI-62 and instructs it to make calls to the other exchange. The CP-63 also receives the dial data signals from the other exchange through the TI-62 and calls the station which is instructed to call by the other exchange.

Overall functions of the system using the Tie-line function are determined by programming made in the CP-63.

Exchange "A"

Exchange "B"

 

Dial

 

data

Audio

Signal

Call

Station

Station

2. Number of stations, paging zones and links

 

 

 

Maximum

 

 

 

 

Maximum number of stations

 

 

 

 

 

 

 

 

 

 

 

 

 

 

number

 

 

 

Maximum

 

 

 

 

 

 

 

of links

 

 

Number

 

 

 

 

Composition

 

 

Maximum

number

 

 

 

 

 

within

 

number of links

of

without

With Paging

 

 

of

 

of exchange (s)

own exchange

between tielined

exchange

 

Paging

(All call+7 zones)

paging

 

 

 

 

 

exchanges

 

 

 

 

 

 

 

 

 

 

 

zones

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

EX-610

EX-620

 

 

 

 

EX-610

EX-620

EX-610

EX-620

Without tie-lines

 

 

 

 

 

 

 

 

 

 

 

 

 

 

12

16

 

1

All

call

56

120

48

112

 

Single

 

 

+7zones

 

 

 

 

 

 

 

 

 

 

 

Exchange

 

 

 

 

 

 

 

 

 

 

 

 

(EX-1)

 

 

 

 

 

 

 

 

 

 

2 exchanges

 

 

 

 

1

All call

56

120

48

112

 

 

 

 

 

 

+7zones

 

 

 

 

 

 

 

 

 

 

 

Exchange 8links

Exchange

12

16

8

 

 

 

 

 

 

 

*1

*1

 

 

 

 

 

 

 

 

"A"

 

"B"

 

 

All

call

 

 

 

 

 

 

 

 

 

 

2

112

240

96

224

 

 

 

 

 

 

+14zones

(EX-2A)

 

(EX-2B)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

3 exchanges

 

 

 

 

 

 

 

 

 

 

 

 

(EX-3A)

 

 

 

1

All

call

56

120

48

112

 

 

 

 

 

 

 

Exchange

 

 

 

 

+7zones

 

 

 

 

 

 

 

 

 

 

 

"A"

 

 

 

 

 

 

 

 

 

 

 

4 links

 

4 links

12

16

4 between each

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

*1

*1

tielined link

 

 

 

 

 

 

 

 

 

Exchange

 

 

 

 

 

 

 

 

Exchange

 

 

 

 

 

All

call

 

 

 

 

"C"

4 links

"B"

 

 

 

3

168

360

144

336

 

 

 

 

 

+21zones

 

 

 

 

 

 

 

 

 

 

 

(EX-3C)

 

(EX-3B)

 

 

 

 

 

 

 

 

 

 

*1 The links within own exchange as well as the tie-line links are used in each tie-line communication.

*2 All call paging is provided to all the paging zones of all the exchanges connected by tie-line.

— 5 —

B. Without personal number

3.Numbering schedule for stations and paging zones

A.With personal number (Standard)

Numbering for stations

Type of exchange

Single Exchange (EX-1)

Exchange "A" (EX-2A/3A)

Exchange "B" (EX-2B/3B)

Exchange "C" (EX-3C)

Model

With

7 zones

Without Paging

per

paging

 

exchange

 

 

EX-610

EX-620

EX-610

EX-620

EX-610

EX-620

Numbering for

paging zones

Paging zone per exchange

All call

Zone

Numbering for stations

Type of

Model

 

exchange

With

Without paging

paging

 

 

 

 

Single Exchange (EX-1)

EX-610

 

Exchange

"A"

(EX-2A/3A)

EX-620

 

 

 

 

 

Exchange

"B"

(EX-2B/3B)

EX-610

 

EX-620

 

 

 

 

 

Exchange

"C"

(EX-3C)

EX-610

 

EX-620

 

 

 

 

 

Zone No. 16 through 22 and No. 31

through 37 are employed for Paging

 

Numbering Schedule

of 45 zones with

3 exchanges established in the system

 

using the exchanges EX-610 and/or EX-620 and EX-630 (256 stations) connected by tie-line.

 

Numbering for paging zones

7 zones

Paging zone per exchange

per

All call

Zone

exchange

4.Reduction of the number of stations and paging zones which results from the use of the Tie-line Interface Unit TI-62.

<EX-610 >

 

 

<EX-620>

LM

Station No.

 

LM

1

200-207

 

1

2

208-215

 

2

3

216-223

 

3

4

224-231

 

4

5

232-239

 

5

6

240-247

 

6

7

248-255

 

7

8

256-263

PI

8

1.Mounting one (1) piece of the TI-62 decreases the number of the LM-62 (the 7th or the 15th LM-62) by one (1).

2.Unless the PI-62 is used, the system can have up to 8 more stations by placing the LM-62 in the 8th or the 16th position.

Station No.

LM

Station No.

Note.

 

 

 

200-207

9

264-271

LM: Line Modem Unit

 

 

 

208-215

10

272-279

PI

: Paging Interface Unit

216-223

11

280-287

Tl

: Tie-line Interface Unit

 

 

224-231

12

288-295

 

 

232-239

13

296-303

 

 

240-247

14

304-311

 

 

248-255

15

312-319

 

 

256-263

16

320-327

 

PI

5. Block diagram for tielined exchanges.

<EX-610 Tie-line>

<EX-620 Tie-line>

Exchange "A" (EX-2A/3A)

Exchange "B"

(EX-2B/3B)

Exchange "C"

(EX-3C)

— 6—

6. The relationship between the PI unit and the LM unit

<The case where the tie-line system consisting of 2 or 3 exchanges has an exchange without the PI unit>

The case where it is necessary to make the paging call from the exchange without the PI unit to the other exchange (s).

Set "Paging" DIP switch (SW-B-4) to ON.

You may not substitute the LM unit (LM8 or LM16) for the PI unit.

EX-610: Max. 48 stations, EX-620: Max. 112 stations

The case where the paging call is unnecessary from the exchange without the PI unit to the other exchange (s).

Set "Paging" DIP switch (SW-B-4) to OFF.

You may substitute the LM unit (LM8 or LM16) for the PI unit.

EX-610: Max. 56 stations, EX-620: Max. 120 stations

Exchange "A"

Exchange "B"

paging call is possible

Exchange "A" Exchange "B"

paging call is impossible

— 7 —

or to
(link No. 4, 5,

WIRING FOR TIE-LINE CONNECTION OF THE EXCHANGES

Each exchange can be connected by means of a cable with a diameter of 0.65mm (25.6 mils.) for a distance of up to 2km (5600 ft).

Regarding the tieline links which are not used, turn off the DIP switch of each unused tieline link inside the Tie-line Unit TI-62.

Connect "T" line (2 wires) of the 4 wires of each link to "R" line (2 wires) of the other exchange. The 2 wires of the "T" line and "R" line have no polarity.

If the BX-610/620 is used, its terminals No. 1 and 2 are for the "R" line and No. 3 and 4 are for the "T" line.

Exchange "A" Exchange "B"

1. Wiring for tie-line connection of 2 exchanges

Exchange "A"

Exchange "B"

EX-2A

EX-2B

Note 1. Any combination of tie-line links between exchanges "A" and "B" is possible. But, in consideration of possible increase in the number of exchanges to be connected from 2 to 3 in the future, we suggest you connect (link No. 0, 1, 2, 3) of exchange "A" to

6, 7) of exchange "B".

2. Wiring for tie-line connection of 3 exchanges

Exchange "A"

EX-3A

Exchange "C"

EX-3C

Note 2. Be sure to connect

Connection of

to

Exchange "B"

EX-3B

(link No. 0, 1, 2,3) to (link No. 4, 5, 6, 7) between the exchanges. will lead to failure of proper operation of the system.

3. DIP Switch selection

DIP Switch

1.Switching arrangements of DIP switches (E-1, E-2, E-3) in the CP-63 make each exchange to be of "EX-1" or "EX-2A" or "EX-2B" or "EX-3A" or "EX-3B" or "EX3C" type.

2.In the event of the tieline link not to be

used, turn off its corresponding DIP switch

TI-62 P.C.B.

 

on the TI-62 unit.

 

 

LINK No.

— 8 —

4. The Example of connection of EX-620 exchange

YR-801 must be connected to J15 for EX-620 exchange (for 128 stations), or to J7 for EX-610 exchange (for 64 station)

EX-620

 

BX-620

EX-610

BX-610

J15

 

T1

J7

T1

"Exchange A"

 

 

 

EX-620

 

 

 

Terminal board

 

 

Terminal board

BX-620

 

 

BX-620

"Exchange B"

EX-620

YR-810

YR-810

for stations

for stations

YR-801

YR-801

for Tie-line

for Tie-line

 

The cables between the exchanges

 

(4 wires x 8 links)

"Exchange A"

"Exchange B"

BX-620 T1

BX-620 T1

— 9 —

5. The Example of connection of EX-620 exchange

"Exchange A"

EX-620

YR-810

for stations

YR-810 must be connected to J15 for EX-620 exchange (for 128 stations), or to J7 for EX-610 exchange (for 64 station)

"Exchange

B"

EX-620

 

Terminal board

Terminal Board

BX-620

BX-620

YR-810

for stations

YR-801 for Tie-line

YR-801 for Tie-line

The cables between the exchanges (4 wires × 4 links)

Terminal board

BX-620

YR-810

for stations

YR-801 for Tie-line

The cables between the exchanges (4 wires x 4 links)

 

The cables between the exchanges (4 wires x 4 links)

 

"Exchange A"

"Exchange B"

"Exchange C"

BX-620 T1

BX-620 T1

BX-620 T1

"Exchange C"

EX-620

— 10 —

No. 470 (400)
No. 740 (700)
No. 200 (100)

PART 1. OPERATING OF CP UNIT AND NO. 200 PROGRAMMING 1. PRECAUTIONS FOR INSTALLATION OF CP-63

Please read following instructions carefully to ensure proper operation of the CP-63

1.Be careful about damage by static electricity as the CP-63 incorporates CMOS IC's. Do not touch components and connectors.

2.Turn off the AC power switch when you take out or insert the CP-63 unit, or any other unit.

3.Always insert the CP-63 unit into the "CP" slot. Otherwise, there is a danger that the unit will be damaged.

4.Make sure mini-jumper for battery back-up is always placed in ON position each time it is used.

5.Incorrect setting of function select switches may lead to incorrect performance.

6.Even if you do not need programming functions, be sure to carry out initial programming and registration at station No.200 when you install the new unit. Otherwise, some other functions may not work properly.

7.The Ni-Cd battery GB50-3FA1 is capable of saving important memory registration data even at times of power failure.

To keep the battery fully charged, do not cut the power off for long hours during the first 8 days after new installation. The CP-63 unit is capable of maintaining the programmed data for the period of 4 weeks after fully charged even in the event of long hours of power failure.

(About 4 weeks (25°C), About 8 days (40°C)

8.We suggest you replace the soldered button battery GB50-3FA1 (115-42-031-9) with the new one according to the following list that shows an expected life span of the battery.

Be sure to make the station No.200 programming after replacement of the battery.

Expected Life Span of small Ni-Cd Battery

 

Ambient temperature

Ambient temperature

Life span

of exchange

of battery

 

0°C

10°C

About 5 years

25° C

35° C

About 4 years

40° C

50° C

About 2 years

9.When shipping the CP-63 unit independently, place the minijumper for battery back-up in "OFF" position. Cover the CP back with cardboard, wrap connector section in aluminium foil and put it in a conductive bag.

FUNCTION SELECT SWITCHES

SW-E

(1 ~ 6)

 

SW-D (1 ~ 6)

These switches select functions.

SW-C

(1 ~ 6)

 

SW-B

(1 ~ 6)

 

SW-A (1 ~ 5)

Link Selection and

 

 

Time Interval Adjustment

for Paging Amplifier Power Remote.

PROGRAM SWITCH for #200 Programming

Set this to "ON" position only at time of initial programming of the exchange and registration of functions. In this case, station No.200 is "programming station" but becomes a normal station when switch is placed in "OFF" position.

Note:

In the event of the tie-line system, programming has to be set up in every exchange.

The first station of each exchange becomes the Programming station: Exchange "A"

Exchange "B"

Exchange "C"

MINI-JUMPER for battery back-up (JP1)

Ni-Cd BATTERY GB50-3FA1 (3.6V 50mAh)

FIXED MINI-JUMPER (JP2)

Note: Do not remove

— 11 —

1. Connect Data Transmitting Unit (DT-
E11) and Data Receiving Unit (DR-
B61).
2. Set channel select switches (CHANNEL SELECT) of DT-E11.
3. Set word select switches (WORD SELECT) of DR-B61.
Note:
*1; The first station of each exchange becomes the programming station:
Exchange "A" ... No. 200 (100)
Exchange "B" ... No. 470 (400)
Exchange "C" ... No. 740 (700) *2; lf there is any error in CMOS memory, you hear calling tone
instead of confirmation tone.

2. INITIAL CP-63 SET UP

In the event of the tie-line system, programming has to be set up in every exchange.

Make sure that you have turned off the AC power switch.

Connect the exchange, terminal boards and stations.

Are Data Transmitting and Receiving Units used?

Remove CP-63 from the exchange.

Set mini-Jumper (JP1) for battery from OFF to ON position.

Set function selection switches (SW-A ~ SW-E) for required functions.

Insert the CP-63 into the exchange.

Put all 4 "Link select" switches of the HC unit upward. (Link No. 15}

 

Switch on the exchange.

Look at indication of LINE ADDRESS of HC (14 LEDs) and SIGNAL

CODE indication (4 LEDs)

 

 

ALL LED lamps are out

Memory is normal

 

SIGNAL CODE indication

Some errors in memory

 

Lighted lamps of LINE ADDRESS

 

LEDs indicate erroneous MEMORY

 

ICs. See Section 3 (Page 13)

Place program switch on front panel of the CP in "ON" position.

Dial operation from station No. 200.

*1

Initial programming of the exchange

 

Dial the Following:

 

Dial tone will be heard

(Station No. 200 (100) becomes a programming station)

Confirmation tone will be heard. *2 (Clears function group S)

Confirmation tone will be heard. *2 (Clears function group A)

Confirmation tone will be heard. *2 (Clears function group B)

Confirmation tone will be heard *2 (Clears function group C)

Confirmation tone will be heard. *2 (Clears function group D)

Confirmation tone will be heard. *2 (Clears function group E)

Confirmation tone will be heard. *2 (Clears personal numbers, single digit dial numbers and remote numbers)

Program necessary functions (Refer to separate instructions for each function) *2

Place program switch on front panel of the CP in "OFF" position.

Dial operation from station No. 200.

*1

(Station No. 200 becomes a normal station.)

—12—

3. TROUBLE SHOOTING

3-1 Check of ROM & NMOS-RAM - No calls on the system.

1.Put the 4 "LINK SELECT" switches of the HC upward (Link No. 15 SELECT) and switch on the AC power of the exchange.

2.If there is no error, the indication lamps will not light.

3.In the event of a memory error, the lamps may light as shown in the example of Fig. 1.

4.The error indications will remain on until you use Link No. 15 for communications.

3-2 Confirming of the CP normal working

If the CP, OC and HC are working normally, the HC's indication lamps of LINE BUSY, LINE ADDRESS and SIGNAL CODE go out.

When any of the lamps lies alight, it is possible that any of the CP, OC or HC is faulty.

Check first that the CLOCK lamp of the HC is lighting, then confirm that the CP is working normally by hearing the clicking sound of the PI unit's relay which is produced when the relay is activated through dial operation of the paging.

If the CP is found working normally, chances are that the HC is faulty, followed by the OC.

3-3 Check of CMOS-RAM (Programmed data memory)

You hear calling tone instead of confirmation tone, if there is CMOS memory error at the time of initial programming and registration using station No. 200, or at the time of registration to Single Digit Number or Personal Number or Remote Number.

3-4 Dial receiving test

1.Instead of the PI-62 unit, use the PIU-52A (a unit used in the EXES-5000 System) to check the dial receiving section of the CP also to check if the signal is correctly transmitted as dialed from the station to be tested.

2.If you place all "LINK SELECT" switches (1 ~ 4) of SW-A on the CP-63 in "OFF" position, conversation is impossible but the dial code from each station is indicated on the LED's of the PIU as dialed. Use this to find the cause of any fault of receiving dial information.

Error ROM • RAM Chip No.

Example

No. 1 and No. 2 out of 4 pcs ROMs (2732) have "read" error.

No. 0 and No. 1 out of 4 sets of N-MOS RAMs (2114) have "read" error.

(One set of RAMs consist of 2 ICs)

Indicate memory error.

LINK SELECT Switchesset

to select No. 15

Fig.1

3.With use of the PI-62 unit fitted with no LED, you can also check that the CP receives the dial signal by hearing the click sound of the relay produced when it is activated.

Example of

Hands-free/HandsetStation

(HF-600M/S)

Fig. 2 DIP switches (SW-A of the CP)

Example of Handset Station (TL-600M/S)

Fig. 3 Dial code indication

3-5 The order of link usage.

After power is on, links are used in numerical order for each communication.

Remember this to help you when problems are found with specific links.

Remarks:

1.Be sure to avoid mistake at the time of DIP switch installation and No. 200 Programming since such mistake may lead to trouble later.

2.Be sure to make "No. 200 Programming" after "Programming Data Table" (attached to this manual) is filled out. Keep the finished "Programming Data Table" (Initial Checking Sheet for the System 133-21-085-5) as a part of complete drawings for each installation.

PI-62 unit

— 13—

3-6 The order of Tie-line link usage

The Tie-line Link Number which is used in calls between exchanges is not directly indicated, but you can possibly get it from the link number which is indicated on the HC-62.

When one Tie-line Link brings up some problems which cause the system not to work properly, try to find which link number is causing the problems from the indication on the HC-62 of the exchange making the call.

As Fig. 1 and Fig. 2 show, in the exchanges which make calls, the DL Link Number corresponds with Tl Tie-line Link Number.

In the exchange which is called, the Tie-line Link Number of the Tl Unit is fixed by connection between exchanges.

DL Links are used in numerical order.

1. Tie-line for 2 exchanges

Exchange which calls

Exchange which is called

Station which is called

Station which calls

Connection Cable

between exchanges

Fig. 1

2. Tie-line for 3 exchanges

Exchange which is called

 

Exchange which calls

No.47O

Station which is called

Station which calls

Fig. 2

— 14 —

Reference for Connection Link Number between DL and Tl Link

 

Exchange which calls

 

Exchange which is called

 

Tl Tie-line Link Number

 

 

DL

2 Tie-lines

3 Tie-lines

Tl Tie-line

Tie-line

Link No

Link Number

Link

 

 

Fixed by Connection

After power switch

is on, Links are

Cable between

used in numerical

Exchanges

order

Note.

If the Tl Tie-line Link which corresponds with the DL Link No. is already busy, then, the next Tie-line Link is automatically used.

— 15 —

4. CP-63 DIP SWITCHES FOR FUNCTION SELECTION

SW-A

SW-B

SW-C

SW-D

SW-E

Functions

Link Selection; Link No. 0 ~ 3

Link Selection; Link No. 4 ~ 7

Link Selection; Link No. 8 ~ 1 1

Link Selection; Link No. 12 ~ 15

Time Interval Adjustment before Paging

Pre-announcement tone

Conference

Call Transfer, Paging during Normal Call Exective Priority (High priority)

Paging

Secretary Transfer, Group Hunting

System Size Selection

Selectable Numbering Schedules

100-400-700/200-470

-740

Selectable Dial Operation for Paging Response

Not

used

 

Not

used

 

Selectable Total Paging Zone Capacity 45/21

Not used

Stations Allowed Access to All Call, Conference and General Purpose Control

Not used

Not used

Group Blocking

Programmable Station Numbering

Pager

Switch OFF

Not Activate

Not Activate

Not Activate

Not Activate

None

Not Activate

Not Activate

Not Activate

Not Activate

Not Activate

EX-610

No.200 (20)~

(OFF)

(OFF)

21 Zones

(OFF)

Not Activate (OFF)

(OFF)

Not Activate

Not Activate

Not Activate

Switch ON

Activate

Activate

Activate

Activate

1 sec

Activate

Activate

Activate

Activate

Activate

EX-620

No. 100 (10)~

——

——

45 Zones

——

Activate

——

——

Activate

Activate

Activate

1 x Exchange

2 x Exchange

 

3 x Exchange

 

EX-1

EX-2A

EX-2B

EX-3A

EX-3B

EX-3C

OFF

OFF

OFF

ON

ON

ON

OFF

ON

OFF

ON

OFF

ON

OFF

OFF

ON

OFF

ON

ON

Memory of Calling Party Indication (Lamp type)

Without memory

With memory

Tone of called Mode at Privacy Sw.ON

Privacy

Continuous calling

Continuous Calling Tone (No. 200 Programming)

Not Activate

Activate

Functions

Switch OFF

Switch ON

Note: *1 Be sure to place the SW-B-4 (Paging) switch in the ON position when Paging and its allied functions are used.

*2 "45 zones" made possible with 3 exchanges are used when EX-610/620 is connected to

EX-630 (not yet available for sale) A: Zone 01 ~ 07, B: Zone 16 ~ 22, C: Zone 31 ~ 37

*3 When set to the "Active" position, the lamp continues to light to indicate all the stations that

have called while the called party has been in the "Privacy" or "Busy" mode.

— 16 —

5. DIP SWITCH SELECTION AND STATION NO. 200 PROGRAMMING FOR EACH FUNCTION

No. 200 Programming should be proceeded in the following manner.

1.Write down the required data in "8. Programming Data Table (Page 42 ~ 47)".

2.Carry out the registration according to "6. Function Code Table for Station No. 200 Programming (Page 18 ~ 20)" and "7. Station No. 200 Programming for Each Function (Page 21 ~ 40)".

 

 

 

 

 

 

 

 

 

Registration or

 

 

 

 

 

 

 

Function

Operation at

 

 

 

 

 

 

 

 

 

 

Each

Station

No.

Single

Digit

Dialing

 

 

Single

Digit

Registration

-

Automatic

 

Access

to

Paging

Single

Digit

Registration

-

Master/Sub

 

Relationship

 

 

-

-

Privacy

 

 

 

 

 

 

Privacy SW

ON

SW-E-5

Continuous

Calling

Tone

Privacy

SW

ON

SW-E-5

at Privacy

Mode

 

 

 

 

 

 

 

 

Continuous

Calling

Tone

 

 

-

SW-E-6

One touch

Response

 

 

 

 

 

 

 

 

Personal

Number Call

 

Personal Number

SW-C-1

 

Registration

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Remote Response

SW-E-5

Remote Response

 

 

 

 

 

Registration

 

 

 

 

 

 

 

 

 

 

 

 

or SW-E-6

 

 

 

 

 

 

 

 

 

 

 

 

Call

Transter

 

 

 

 

 

 

-

SW-B-2

 

 

 

 

 

 

 

 

 

 

 

 

SW-B-2

 

 

 

 

 

 

 

 

 

 

 

 

SW-B-4

 

 

 

 

 

 

 

 

 

 

 

 

SW-A-5

Paging

during

Normal

Calls

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

SW-C-5

 

 

 

 

 

 

 

 

 

 

 

 

SW-C-2

Group

Hunting

 

 

 

 

 

-

SW-B-5

Secretary

 

Transter

 

 

Privacy

SW

ON

SW-B-5

Executive

 

Priority

 

 

 

 

-

SW-B-3

(Highest

Priority)

 

 

 

 

 

 

 

 

 

 

Conference

 

 

 

 

 

 

 

-

SW-B-1

 

 

 

 

 

 

 

 

 

 

 

 

SW-B-4

 

 

 

 

 

 

 

 

 

 

 

 

SW-A-5

Paging

 

 

 

 

 

 

 

 

 

-

SW-C-5

 

 

 

 

 

 

 

 

 

 

 

 

SW-C-2

Numbering

 

Schedules

of

 

 

-

SW-C-1

Tie-line

System

 

 

 

 

 

 

 

 

 

 

Programmable

Station

Numbering

 

 

-

SW-D-5

Group

Blocking

 

 

 

 

 

-

SW-D-4

Programmable

 

 

 

 

 

 

 

Restricted

Access

 

 

 

 

-

SW-D-1

for

Stations

 

 

 

 

 

 

 

 

Selection

of

Calling

Tone

 

 

-

-

Selection

of

Paging Pre-announcement

 

 

-

-

Tone

Duration

 

 

 

 

 

 

 

 

 

 

 

 

Time-out of Conversation

 

-

-

Time-out of Paging Call

 

-

-

In/Out Annunciation

 

 

-

SW-C-1

Calling

Party

 

Indication

 

-

SW-E-4

(Lamp

Type)

 

 

 

 

 

 

 

 

 

 

 

 

 

Pager

 

 

 

 

 

 

 

 

-

SW-D-6

CP DIP Switch

Function

-

-

-

Tone of Called Mode

at Privacy SW ON

Tone of Called Mode

at Privacy SW ON

Continuous Calling Tone

Selectable Numbering Schedules

Tone of Called Mode at

Privacy SW ON

or Continuous Calling Tone

Call Transfer, Paging during Normal Calls

Call Transfer, Paging during Normal Calls

Paging

Time Interval Adjustment before Paging Pre-announcement Tone

Paging Zones Capacity 45/21

Selectable Dial Operation for Paging Response

Secretary Transfer, Group Hunting

Secretary Transfer, Group Hunting

Executive Priority

(Highest Priority)

Conference

Paging

Time Interval Adjustment before Paging Pre-announcement Tone

Paging Zones Capacity 45/21

Selectable Dial Operation for Paging Response

Selectable Numbering Schedules

Programmable Station Numbering

Group Blocking

Stations Allowed

Access to All Call,

Conference and

General Purpose

Control

-

-

-

-

Selectable Numbering Schedules

Memory of Calling Party Indication

(Lamp Type)

Pager

 

 

No. 200

Programning

 

 

ON/OFF

Function

Function

 

Function

Group

Code

 

 

 

 

 

-

-

-

 

-

 

-

A

54

Automatic Access

to Paging

-

B

61

Master/Sub

Relationship

OFF

-

-

 

-

 

ON

-

-

 

-

 

ON

A

51

Continuous

Calling

Tone

OFF

-

-

 

-

 

ON

 

 

 

 

 

ON

A

51

ON

 

 

ON

 

 

ON

 

 

ON/OFF

-

-

ON/OFF

 

 

OFF

 

 

ON

C

70

ON

B

62

ON

B

60

ON

A

50

ON

-

-

ON

 

 

ON/OFF

 

 

ON/OFF

 

 

OFF

 

 

ON

C

70

ON/OFF

S

40

ON

E

90

 

C

71

ON

D

81

 

D

82

 

A

52

 

A

53

 

A

56

ON

A

57

 

A

58

 

A

59

-

S

41

-

S

42

-

S

45

-

S

46

OFF

-

-

ON/OFF

C

72

ON

-

-

Continuous Calling Tone

-

-

Paging Zone

Group Hunting

Secretary Transter

Executive Priority

-

Paging Zone

Numbering

Schedules of

 

Tie-line

System

 

 

Programmable

Station

 

Numbering

 

 

 

Establishment

of

 

 

Each Groups

 

 

 

Allowing

 

Calls

 

 

among Groups

 

 

Allowing

Access

to

 

Paging

Zones

 

 

 

Stations

Allowed

Access

to

All

Call

 

 

 

 

 

Stations

Allowed

Access

to

Conference

 

 

 

Stations

Allowed

Access

to

One-shot Make Output

 

Stations

Allowed

Access

to

Make/Break Output

 

Stations

Allowed

Access

to

8

Selectable/Decimal

 

Output

 

 

 

 

 

Station

Allowed

Access

 

to

4

Decimal

 

 

 

Digits

Output

 

 

 

Selection

of

Calling Tone

 

Selection

of

Paging

 

Pre-announcement Tone Duration

Time-out of Conversation

Time-out of Paging Call

-

Group of Calling Party

Indication

-

— 17 —

6. FUNCTION CODE TABLE FOR STATION NO. 200 PROGRAMMING

Function

Function

 

Func-

 

tion

Group

 

 

 

Code

 

 

 

 

Numbering schedules

40

 

of Tie-line system

 

 

 

 

 

Selection of Calling

 

41

 

Tone

 

 

 

 

S

Selection of Paging

 

42

Pre-announcement

Tone

 

 

 

Time-out of

 

45

 

Conversation

 

 

Time-out of Paging

 

46

 

Call

 

 

 

 

 

Executive Priority

 

50

Continuous Calling

 

A. Clearance at one time

Tone

51

 

Station Allowed

52

Access to All Call

 

Stations Allowed

53

Access toConference

 

Automatic Access to

54

Paging

 

AStations Allowed

 

Access to One Shot

56

 

Make Output

 

 

Stations Allowed

 

 

Access to Make/

57

 

Brake Output

 

 

Stations Allowed

 

 

Access to 8 Selectable/

58

 

Decimal Output

 

 

Stations Allowed

 

 

Access to 4 Decimal

59

 

Digits Output

 

 

Secretary Transfer

60

B

Master/Sub

61

 

Group Hunting

62

 

Paging Responce,

70

 

Paging Priority

C

Group Blocking of

71

Each Group

 

Group of Calling

72

 

Party Indication

 

 

 

Group Blocking:

 

 

Allowing Calls

81

D

Among Groups

 

Group Blocking:

 

 

 

 

AllowingAccess

82

 

to Paging Zones

 

E

Programable Station

90

Numbering

 

*

Personal Number

 

Single Digit Dialing

-

RemoteResponse

Clearance of Function

Confirmation tone

Confirmation

tone

Confirmation tone

Confirmation

tone

Confirmation

tone

Confirmation

tone

Confirmation tone

Confirmation

tone

Confirmation

tone

Function Registration on All Stations

Confirmation tone

Confirmation

tone

Note: *Can be registered at each station.

Clearance of Function by Function Group

Confir-

mation (ClearsfunctiongroupS) tone

Confir-

(Clears function group A)

mation

tone

 

Confir-

 

mation

(Clears function group B)

tone

 

Confir-

 

mation

(Clears function group C)

tone

 

Confir-

 

mation

(Clearsfunction group D)

tone

 

Confir-

 

mation

(Clears function group E)

tone

 

Confir-

(Clears functions of Personal

mation

No., Single Digit Dialing and

tone

Remote Response)

— 18 —

FUNCTION CODE TABLE FOR STATION NO. 200 PROGRAMMING

B. Programming of System

Function

Function

Function

 

Remarks

 

 

Group

Code

 

 

 

 

 

 

 

 

 

 

 

The following standard station numbering

 

 

 

schedules of the exchanges A, B and C are

 

 

 

obtainable. (Hardwired station number)

 

Numbering Schedules

 

SW-C-1

A

B

C

 

of Tie-line System

 

OFF

200~

470~

740~

 

 

 

 

First station number

40

ON

100~

400~

700 ~

 

set-up in each

 

 

 

 

 

 

 

 

 

 

exchange

S

Selection of Calling Tone

41

 

Selection of Paging

 

 

Pre-announcement

42

 

Tone Duration

 

 

Time-out Conversation

45

 

Time-out Paging Call

46

The first station number of each exchange in order of the exchanges, A, B and C can be set as any of the following numbers:

100/200/300/400/500/600/700/800/900

(Hardwired station number)

Two different calling tones, single note tone or trill note tone, are available in selection for the Hands-free system except the continuous calling tone.

You can select the length of time of paging pre-announcement tone.

Programming is possible so that stations can be disconnected automatically from the speech path in the unit of Minute and the Hurry-up Signal Tone can be heard 10 seconds before the disconnection.

Programming is possible so that stations can be disconnected automatically from the Paging circuit in the unit of Minute and the Hurry-up Signal Tone can be heard 10 seconds before the disconnection.

Operating for Programming

First Station No. First Station No. of Exchange "A" of Exchange "B" 1 ~ 8 (First digit) 2 ~ 9 (First digit)

0:Without Calling Tone

1:Single Note Tone (0.2 sec.)

2:Trill note Tone (0.3 sec.)

First Station No.

of Exchange "C"

3 ~ 9 (First digit)

0:Without Paging pre-announcement Tone

1:Paging Pre-announcement Tone (1 sec.)

2:Paging Pre-announcement Tone (2 sec.)

00:Without Time-out function

01~99: Length limited (minute)

00: Without Time-out function 01~99: Length limited (minute)

Initially

Programmed

Mode

Standard

Station Numbering A/B/C= 200/470/740 or

A/B/C=

100/400/700

Trill note Tone (0.3 sec.)

Paging Pre-announce- ment Tone

(2 sec.)

Without

Time-out

Without

Time-out

— 19 —

FUNCTION CODE TABLE FOR STATION NO. 200 PROGRAMMING

C. Programming of each Function

Func-

tion Function

Group

Executive Priority

Continuous Calling

Tone

Station Allowed

Access to All Call

Stations Allowed

Access to

Conference

Automatic Access to

Paging

AStations Allowed Access to One-Shot Make Output

Stations Allowed Access to Make/ Break Output

Stations Allowed Access

to 8 Selectable/ Decimal Output

Stations Allowed Access to 4 Decimal Digits Output

Func-

tion

1st Parameter

2nd Parameter 3rd Parameter 4th Parameter

OPERATING FOR PROGRAMMING

Code

 

 

 

50

Station No.

ON/OFF (1/0)

 

51

Station No.

ON/OFF (1/0)

 

52

Station No.

ON/OFF(1/0)

 

53

Station No.

ON/OFF (1/0)

 

54

Station No.

ON/OFF (1/0)

 

56

Station No.

ON/OFF(1/0)

 

57

Station No.

ON/OFF (1/0)

 

58

Station No.

ON/OFF (1/0)

 

59

Station No.

ON/OFF (1/0)

 

 

Secretary Transfer

60

Executive

Secretary Station

 

 

 

 

Station No.

No.

 

 

 

 

 

 

 

 

 

B

Master/Sub

61

Sub Station No.

Mater Station No.

 

 

 

 

Group Hunting

62

Main station No.

Transfered Station

 

 

 

 

 

 

 

No.

 

 

 

 

Paging Zone

 

01~21

The First Station The Last Station

 

 

70

Zone No. 01~45

No. of the Zone

No. of the Zone

 

C

Group Blocking:

 

 

The First Station

The Last Station

 

Establishment of

71

Group No. (1~6)

 

 

Each Group

 

 

No. of the Group

No. of the Group

 

 

 

 

 

 

 

 

 

Group of Calling

72

Group No. (1~6)

The First Station

The Last Station

 

 

Party Indication

No. of the Group

No. of the Group

 

 

Group Blocking:

 

Calling Group No.

Called Group No.(s)

(1~8)

 

 

Allowing Calls

81

 

 

(1~8)

(Plural)

 

 

 

 

Among Groups

 

 

 

 

D

 

 

 

 

 

 

 

 

Group Blocking:

82

Paging Zone No. of

Paing Group No.(s)

 

(1~6)

 

 

Allowing Access

Paged Group

(Plural)

 

 

 

 

to Paging Zones

 

(00~21, 00~45)

 

 

 

 

 

 

 

 

 

 

 

 

Hardwired Station

Programmed Sta-

 

 

 

 

 

 

No.

tion No.

 

 

 

 

Programable

 

*1

*2

 

 

 

E

90

 

 

 

 

 

Station Numbering

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

The First

The Last

The First

The Last

 

 

 

Hardwired

Hardwired

Programmed

Programmed

 

 

 

Station No.

Station No.

Station No.

Station No.

*2

1 Station No.'s except Programmed Station No.'s are Hardwired Station No.'s No. 100~/200~/300~/400~/470~/500~/600~/700~/740~/800~/900~.

2 Programmed Station No.'s are No. 200~999/No. 100~999.

— 20 —

7. STATION NO. 200 PROGRAMMING FOR EACH FUNCTION

7-1 EXECUTIVE PRIORITY (FUNCTION CODE 50) (HIGHEST PRIORITY)

EXECUTIVE PRIORITY (HIGHEST PRIORITY)

STEP 1

Touch

Function Code

NO

New Registration?

YES

Executive Station No. ON

Touch

Executive Station No. ON

Touch

Confirmation tone

NO

New Registration finished?

YES

NO

Release?

YES

Executive Station No. OFF

Touch

Executive Station No. OFF

Touch

Confirmation tone

NO

Release finished?

YES

Return

NOTES

1. To allow all the stations to have this function,

Touch

(Confirmation tone

will be heard.)

 

 

10 times

Be sure to depress the

key steadily.

2.To release at one time the data programmed into all the stations for this function,

Touch

(Confirmation tone

will be heard.)

 

 

10 times

3.Re-start at Step 1 when mis-dialing occurs.

(All other registrations remain valid.)

4.CP DIP switch B-3 must be "ON" to employ this function.

— 21 —

7-2 CONTINUOUS CALLING TONE (FUNCTION CODE 51)

CONTINUOUS CALLING TONE

STEP 1

Touch

Function Code

NO

New Registration?

YES

Continuously Called Station No. ON

Touch

Continuously Called Station No. ON

Touch

Confirmation tone

NO

New Registration finished?

YES

NO

Release?

YES

Continuously Called Station No. OFF

Touch

Continuously Called Station No. OFF

Touch

Confirmation tone

NO

Release finished?

YES

Return

NOTES

1. To allow all the stations to have this function,

Touch

(Confirmation tone

will be heard.)

 

 

10 times

Be sure to depress the

key steadily.

2.To release at one time the data programmed into all the stations for this function,

Touch

(Confirmation tone

will be heard.)

 

 

10 times

3.Re-start at Step 1 when mis-dialing occurs. (All other registrations remain valid.)

4.CP DIP switch E-6 must be "ON" to employ this function.

— 22 —

7-3 STATIONS ALLOWED ACCESS TO ALL CALL (FUNCTION CODE 52)

STATIONS ALLOWED ACCESS TO ALL CALL

STEP 1

Touch

Function Code

NO

New Registration?

YES

Allowed Station No.

ON

Touch

Allowed Station No. ON

Touch

Confirmation tone

NO

New Registration finished?

YES

NO

Release?

YES

Allowed Station No.

OFF

Touch

Allowed Station No. OFF

Touch

Confirmation tone

NO

Release finished?

YES

Return

NOTES

1. To allow all the stations to have this function,

Touch

(Confirmation tone

will be heard.)

10 times

Be sure to depress the

key steadily.

2.To release at one time the data programmed into all the stations for this function,

Touch

(Confirmation tone

will be heard.)

 

 

10 times

3.Re-start at Step 1 when mis-dialing occurs. (All other registrations remain valid.)

4.Programming is necessary only if CP DIP switch D-1 is "ON".

— 23 —

7-4 STATIONS ALLOWED ACCESS TO CONFERENCE (FUNCTION CODE 53)

STATIONS ALLOWED ACCESS TO CONFERENCE

STEP 1

Touch

Function Code

NO

New Registration?

Allowed Station No.

ON

Touch

Allowed Station No.

ON

Touch

Confirmation tone

NO

New Registration finished?

YES

NO

Release?

YES

Allowed Station No.

OFF

Touch

Allowed Station No. OFF

Touch

Confirmation tone

NO

Release finished?

YES

Return

NOTES

1. To allow all the stations to have this function,

Touch

(Confirmation tone

will be heard.)

 

 

10 times

Be sure to depress the

key steadily.

2.To release at one time the data programmed into all the stations for this function.

Touch

(Confirmation tone

will be heard.)

 

 

10 times

3.Re-start at Step 1 when mis-dialing occurs. (All other registrations remain valid.)

4.Programming is necessary only if CP DIP switch D-1 is "ON".

Switch B-1 must be "ON" to employ this function.

— 24 —

7-5 AUTOMATIC ACCESS TO PAGING (FUNCTION CODE 54)

HANDSET SUBSTATIONS ALLOWED ACCESS TO PAGING

STEP 1

Touch

 

 

Function Code

 

 

 

New Registration?

NO

 

 

 

 

 

Allowed Station No.

ON

 

 

Touch

 

 

 

 

Allowed Station No.

ON

 

 

Touch

 

 

 

 

Confirmation tone

 

 

NO

New Registration finished?

 

 

 

 

YES

 

 

 

 

Release?

 

NO

 

 

 

 

 

 

YES

 

 

 

 

Allowed Station No.

OFF

 

 

Touch

 

 

 

 

Allowed Station No.

OFF

 

 

Touch

 

 

 

 

Confirmation tone

 

 

NO

Release finished?

 

 

 

 

 

 

YES

 

 

 

 

Return

 

 

NOTES

 

 

 

 

1. To allow all the stations to have this function,

3. Re-start at Step 1 when mis-dialing occurs.

Touch

 

(Confirmation tone

(All other registrations remain valid.)

 

 

 

 

will be heard.)

 

 

 

 

 

 

Be sure to depress the

key steadily

 

 

 

2.To release at one time the data programmed into all the stations for this function.

Touch

(Confirmation tone

will be heard.)

 

— 25 —

COMPLEMENTARY NOTES

(1) Automatic Access to Paging

This function facilitates Paging / Paging response from a

Substation TL-600S. Just picking up the Handset of Substation automatically activates Paging or Paging Response mode.

(2) Required Programming for Automatic Access to Paging from Handset Substation.

2-1) First, connect a Master Station HF-600M or TL-600M in place of a Substation TL-600S.

2-2) Program at that station a necessary function for Single Digit

Dialing such as Paging, Paging Response, Personal Number Call or etc.

2-3) Then, replace the Master Station with a Substation TL-600S. 2-4) Program "Automatic Access to Paging from Handset Substation

(Function Code 54)" at the Station No. 200 according to the programming instructions.

(3) Single Digit Dialing and Automatic Access to Paging

By programming "Single Digit Dialing" at any master station, a single touch of the dial activates "Station Call", "Personal Number Call", "Paging" or "Paging Response" mode. But in using a TL-600S and a HF-600S, "Automatic Access to Paging from Handset Substation" function cannot be adopted only by programming "Single Digit Dialing" at the station. It also requires the programming for Function Code 54 at No. 200 Station.

(4)A call to Master Station from Handset or Hands-free/ Handset Substation

"Master/Sub Relationship (Function Code 61)" can be programmed into Handset Substation TL-600S or Hands-free/

Handset Substation HF-600S etc., where you can call the

relative Master Station by a single touch of the dial

or by

picking up the Handset.

 

In activating a mode with Hands-free/Handset Substation HF-600S by picking up the Handset, "Privacy" switch on the Station is to be "ON" position.

(5) Call by Dialing

& Picking up the Handset

 

 

 

 

Call to Master Station

 

 

 

By dialing

By picking up

 

 

Necessary

Handset

Function

 

 

 

Programming

at

at

 

 

 

 

 

HF-620Sor

TL-600S or

 

 

 

HF-600S

HF-600S

 

 

 

 

(Privacy SW. ON)

Single Digit

 

Single Digit

 

 

 

Registration

 

 

Dialing

 

 

 

 

at Station

 

 

 

 

 

 

Master/sub

 

Programming at

 

 

Station No. 200

 

 

Relationship

 

 

 

(Function Code 61)

 

 

 

 

 

 

 

1.

Single Digit

 

 

 

 

Registration

 

 

Automatic Access to Paging

 

at Station

 

 

Paging (or Calling)

 

 

 

 

from Handset Substation

2.

Programming at

 

 

 

 

Station No.200

 

 

 

 

(Function Code 54)

 

 

Note.

Paging Call, Paging Response or Personal Number Call

By dialing

By picking up

Handset

 

at

at

HF-620S or

TL-600S or

HF-600S

HF-600S

 

(Privacy SW. ON)

Possible

Impossible

Possible but usually Not to be used Possible across the tie-lined exchange. Impossible across the tie-lined exchange.

— 26 —

7-6 STATIONS ALLOWED ACCESS TO ONE-SHOT MAKE OUTPUT (FUNCTION CODE 56)

STATION ALLOWED ACCESS TO ONE SHOT MAKE OUTPUT

STEP 1

Touch

Function Code

NO

New Registration?

 

 

Allowed Station No.

ON

 

 

Touch

 

 

 

 

Allowed Station No.

ON

 

 

Touch

 

 

 

 

Confirmation tone

 

 

NO

New Registration finished?

 

 

 

 

YES

 

 

 

 

Release?

 

NO

 

 

 

 

 

 

YES

 

 

 

 

Allowed Station No.

OFF

 

 

Touch

 

 

 

 

Allowed Station No.

OFF

 

 

Touch

 

 

 

 

Confirmation tone

 

 

NO

Release finished?

 

 

 

 

 

 

YES

 

 

 

 

Return

 

 

NOTES

 

 

 

 

1. To allow all the stations to have this function,

3.

Re-start at Step 1 when mis-dialing occurs.

Touch

 

(Confirmation tone

(All other registrations remain valid.)

 

 

 

 

will be heard.)

 

 

 

 

 

 

Be sure to depress the

key steadily.

4.

Programming is necessary only if CP DIP switch D-1 is "ON".

 

 

 

2.To release at one time the data programmed into all the stations for this function.

Touch

(Confirmation tone

will be heard.)

 

— 27 —

7-7 STATIONS ALLOWED ACCESS TO MAKE/BREAK OUTPUT (FUNCTION CODE 57)

STATIONS ALLOWED ACCESS TO MAKE/BREAK OUTPUT

STEP 1

Touch

Function Code

NO

New Registration?

Allowed Station No. ON

Touch

Allowed Station No. ON

Touch

Confirmation tone

NO

New Registration finished?

YES

NO

Release?

YES

Allowed Station No. OFF

Touch

 

 

Allowed Station No.

OFF

 

 

Touch

 

 

 

 

Confirmation tone

 

 

NO

Release finished?

 

 

 

 

 

 

YES

 

 

 

 

Return

 

 

NOTES

 

 

 

 

1. To allow all the stations to have this function,

3.

Re-start at Step 1 when mis-dialing occurs.

 

 

(Confirmation tone

(All other registrations remain valid.)

Touch

 

 

 

 

will be heard.)

 

 

 

 

 

 

Be sure to depress the

key steadily.

4.

Programming is necessary only if CP DIP switch D-1 is "ON".

 

 

 

2.To release at one time the data programmed into all the stations for this function.

Touch

(Confirmation tone

will be heard.)

 

— 28 —

7-8 STATIONS ALLOWED ACCESS TO 8 SELECTABLE OR DECIMAL OUTPUT (FUNCTION CODE 58)

STATIONS ALLOWED ACCESS TO 8 SELECTABLE

OR DECIMAL OUTPUT

STEP 1

Touch

Function Code

 

 

New Registration?

NO

 

 

 

 

 

YES

 

 

 

 

Allowed Station No.

ON

 

 

Touch

 

 

 

 

Allowed Station No.

ON

 

 

Touch

 

 

 

 

Confirmation tone

 

 

NO

New Registration finished?

 

 

 

 

YES

 

 

 

 

Release?

 

NO

 

 

 

 

 

 

YES

 

 

 

 

Allowed Station No.

OFF

 

 

Touch

 

 

 

 

Allowed Station No.

OFF

 

 

Touch

 

 

 

 

Confirmation tone

 

 

NO

Release finished?

 

 

 

 

 

 

YES

 

 

 

 

Return

 

 

NOTES

 

 

 

 

1. To allow all the stations to have this function,

3.

Re-start at Step 1 when mis-dialing occurs.

 

 

(Confirmation tone

(All other registrations remain valid.)

Touch

 

 

 

 

will be heard.)

 

 

 

 

 

 

Be sure to depress the

key steadily.

4.

Programming is necessary only if CP DIP switch D-1 is "ON".

 

 

 

2.To release at one time the data programmed into all the stations for this function,

Touch

(Confirmation tone will be heard.)

— 29 —

7-9 STATIONS ALLOWED ACCESS TO 4 DECIMAL DIGITS OUTPUT (FUNCTION CODE 59)

STATIONS ALLOWED ACCESS TO 4 DECIMAL DIGITS OUTPUT

STEP 1

Touch

Function Code

NO

New Registration?

YES

 

 

Allowed Station No.

ON

 

 

Touch

 

 

 

 

Allowed Station No.

ON

 

 

Touch

 

 

 

 

Confirmation tone

 

 

NO

New Registration finished?

 

 

 

 

YES

 

 

 

 

Release?

 

NO

 

 

 

 

 

 

Allowed Station No.

OFF

 

 

Touch

 

 

 

 

Allowed Station No.

OFF

 

 

Touch

 

 

 

 

Confirmation tone

 

 

NO

Release finished?

 

 

 

 

 

 

Return

 

 

NOTES

 

 

 

 

1. To allow all the stations to have this function.

3.

Re-start at Step 1 when mis-dialing occurs.

 

 

(Confirmation tone

(All other registrations remain valid.)

Touch

 

 

 

 

will be heard.)

 

 

 

 

 

 

Be sure to depress the

key steadily.

4.

Programming is necessary only if CP DIP switch D-1 is "ON".

 

 

 

2.To release at one time the data programmed into all the stations for this function,

Touch

(Confirmation tone will be heard.)

— 30 —

7-10 SECRETARY TRANSFER (FUNCTION CODE 60)

SECRETARY TRANSFER

Step 1

Touch

Function Code

NO

New Registration?

Executive Station No.

Secretary Station No.

Touch

 

Executive Station No.

Secretary Station No.

Touch

 

Confirmation tone

NO

 

New Registration finished?

 

YES

 

NO

Release?

 

YES

Executive Station No.

Executive Station No.

Touch

 

Executive Station No.

Executive Station No.

Touch

 

Confirmationtone

NO

Release finished?

YES

Return

NOTES

1.To release at one time the data programmed into all the stations for this function,

Touch

(Confirmation tone will be heard.)

2.Re-start at Step 1 when mis-dialing occurs.

(All other registrations remain valid.)

3.Switch B-5 must be "ON" to employ this function.

4.Programming of Secretary Transfer can be made in a daisy chain method. For their examples, refer to the following sketch.

— 31 —

7-11 MASTER/SUB RELATIONSHIP (FUNCTION CODE 61)

MASTER/SUB RELATIONSHIP

Step 1

Touch

 

 

Function Code

 

 

 

NO

 

 

New Registration?

 

 

YES

 

Sub Station No.

Master Station No.

Touch

 

 

 

Sub Station No.

Master Station No.

Touch

 

 

 

 

 

Confirmation tone

NO

New Registration finished?

 

 

 

YES

 

 

 

Release?

NO

 

 

 

 

 

YES

 

Sub Station No.

Sub Station No.

Touch

 

 

 

Sub Station No.

Sub Station No.

Touch

 

 

 

 

 

Confirmation tone

NO

 

Release finished?

 

 

 

 

YES

 

 

 

Return

 

NOTES

 

 

 

1. To release at one time the data programmed into all the

2.

Re-start at Step 1 when mis-dialing occurs.

stations for this function.

 

 

(All other registrations remain valid.)

Touch

(Confirmation tone will be heard.)

— 32 —

7-12 GROUP HUNTING (FUNCTION CODE 62)

TRANSFERED STATION No. FOR GROUP HUNTING

Step 1

Touch

Function Code

NO

New Registration?

 

Original Station No.

Transfered Station No.

 

Touch

 

 

 

Original Station No.

Transfered Station No.

 

Touch

 

 

 

 

Confirmation tone

 

 

 

NO

New Registration finished?

 

 

 

 

 

 

YES

 

 

 

NO

 

 

Release?

 

 

 

YES

 

Original Station No.

Original Station No.

 

Touch

 

 

 

 

 

 

Original Station No.

Original Station No.

 

 

Touch

 

 

Confirmation tone

NO

Release finished?

YES

Return

NOTES

1.To release at one time the data programmed into all the stations for this function,

3. Switch B-5 must be "ON" to employ this function.

Touch

(Confirmation tone

will be heard.)

 

4. Programming of Group Hunting can be made in a daisy chain

method. For their examples, refer to the following sketch.

2.Re-start at Step 1 when mis-dialing occurs. (All other registrations remain valid.)

— 33 —

7-13 PAGING ZONE (FUNCTION CODE 70)

ESTABLISHMENT OF EACH PAGING ZONE

Step 1

Touch

 

Function Code

 

Paging Zone No.

1st Station No.

Last Station No.

(00~21, 00~45)

of the Zone

of the Zone

Touch

 

 

Paging Zone No.

1st Station No.

Last Station No.

(00~21, 00~45)

of the Zone

of the Zone

Touch

 

 

Confirmation tone

NO

New Registration finished?

YES

Return

NOTES

1.To release at one time the data programmed into all the Zones for this function.

Touch

(Confirmation tone will be heard.)

2.Re-start at Step 1 when mis-dialing occurs. (All other registrations remain valid.)

3.Switch B-4 must be "ON" to employ this function.

4.In the case "Paging Response Without Zone Number" mode

is selected by the DIP Switch SW-C-2 this

registrationisessential.

5. Zone number series of each exchange in Tie-line system.

Model

 

EX-610/620

 

Type of

 

EX-610/620

(tie-lined to

EX-630

 

 

EX-630)

 

exchange

 

 

 

 

Exchange

"A"

No. 01~07

No. 01~07

No. 01~15

Exchange

"B"

No. 08~14

No. 16~22

No. 16~30

Exchange

"C"

No. 15~21

No. 31~37

No. 31~45

—34—

GROUP BLOCKING 1

ESTABLISHMENT OF EACH GROUP

Step 1

Touch

Function Code

Group No.

1st Station No.

Last Station No.

(1 ~6)

of the Group

of the Group

Touch

 

 

Group No.

1st Station No.

Last Station No.

(1 ~6)

of the Group

of the Group

Touch

 

 

 

Confirmation tone

 

NO

 

 

New Registration finished?

 

 

YES

 

 

Return

 

NOTES

 

 

1. To release at one time the data programmed into all the

2. Re-start at Step 1 when mis-dialing occurs.

groups for this function,

(All other registrations remain valid.)

(Confirmation tone

Touch 3. CP DIP switch D-4 must be "ON" to employ this function. will be heard.)

— 35 —

7-15 CALLING PARTY INDICATION (LAMP TYPE) (FUNCTION CODE 72)

Registration of station number(s) having indication panel.

ESTABLISHMENT OF EACH GROUP

Step 1

Touch

Function Code

Group No.

1 st Station No.

Last Station No.

(1 ~ 8)

of the Group

of the Group

Touch

 

 

Group No.

1st Station No.

Last Station No.

(1 ~ 8)

of the Group

of the Group

Touch

 

 

Confirmation tone

NO

New Registration finished?

YES

Return

NOTES

1.To release at one time the data programmed into all the groups for this function,

Touch

(Confirmation tone

will be heard.)

 

2.Re-start at Step 1 when mis-dialing occurs. (All other registrations remain valid.)

3.When the Indication Panel belongs to only one (1) station, you should write the station number in both "First Station No. "and "Last Station No." columns.

— 36 —

7-16 GROUP BLOCKING 2 : ALLOWING CALLS AMONG GROUPS (FUNCTION CODE 81)

GROUP BLOCKING 2

ALLOWING CALLS AMONG GROUPS

Step 1

Touch

Function Code

NO

New Registration?

YES

 

Calling Group

Called Group

 

No. (1 ~8)

No. (s) (1 ~8) (max. 7)

 

Touch

 

 

 

Calling Group

Called Group

 

No. (1 ~8)

No. (s) (1 ~ 8) (max. 7)

 

Touch

 

 

 

Confirmation tone

 

NO

 

 

 

New Registration finished?

 

 

YES

 

 

 

Release?

NO

 

 

 

 

 

YES

 

 

Calling Group No. (1 ~ 8)

 

Touch

 

 

 

Calling Group No. (1 ~ 8)

 

Touch

 

 

 

Confirmation tone

 

NO

 

 

 

Release finished?

 

 

YES

 

NOTES

 

Return

 

 

 

 

1. To release at one time the data programmed into all the

3.

Do not register a Group to call itself.

groups for this function.

 

 

 

 

(Confirmation tone

4.

CP DIP switch D-4 must be "ON" to employ tins function.

Touch

 

 

will be heard.)

 

 

 

 

 

2.Re-start at Step 1 when mis-dialing occurs (All other registrations remain valid.)

— 37 —

7-17 GROUP BLOCKING 3 : ALLOWING GROUP ACCESS TO PAGING (FUNCTION CODE 82)

GROUP BLOCKING 3

ALLOWING ACCESS TO PAGING ZONES

Step 1

Touch

Function Code

New Registration?

NO

 

YES

 

 

Paging Zone

Paging Group No. (S)

(00~21,00~45)

 

(1 ~ 6) (max. 6)

Touch

 

 

Paging Zone

Paging Group No. (S)

(00~21, 00~45)

 

(1 ~ 6) (max. 6)

Touch

Confirmation tone

NO

New Registration finished?

YES

NO

Release?

YES

Paging Zone (00-21,00-45)

Touch

Paging Zone (00-21,00-45)

Touch

Confirmation tone

NO

NOTES

1.To release at one time the data programmed into all the groups for this function.

Release finished?

YES

Return

2.Re-start at Step 1 when mis-dialing occurs (All other registrations remain valid.)

Touch

(Confirmation tone

will be heard.)

 

3. CP DIP switch D-4 must be "ON" to employ this function.

— 38 —

7-18 PROGRAMMABLE STATION NUMBERING (FUNCTION CODE 90)

A. Programming of Single Station Number

PROGRAMMABLE STATION NUMBERING

Step 1

Touch

Function Code

NO

New Registration?

Hardwired Station No.

Programmed Station No.

Touch

Hardwired Station No.

Programmed Station No.

Touch

Confirmation tone

NO,

New Registration finished?

YES

NO

Release?

YES

Hardwired Station No.

Hardwired Station No.

Touch

Hardwired Station No.

Hardwired Station No.

Touch

Confirmation tone

NO

Release finished?

YES

Return

NOTES

1. To release all registered Programmed Station No.'s at one time,

Touch

(Confirmation tone will be heard.)

2.Re-start at Step 1 when mis-dialing occurs. (All other registrations remain valid.)

3.Any one Programmed Station No. cannot be assigned to more than one Hardwired Station.

4.CP DIP switch D-5 must be "ON" to employ this function.

— 39 —

B. Programming of Serial Station Numbers

PROGRAMMABLE STATION NUMBERING

Step 1

Touch

 

 

Function Code

 

 

 

New Registration?

NO

 

 

 

 

 

 

YES

 

 

First

Last

 

First

 

Last

Hardwired Station No. Hardwired Station No. Programmed Station No. Programmed Station No.

First

Last

 

First

 

Last

Hardwired Station No. Hardwired Station No. Programmed Station No. Programmed Station No.

 

 

Confirmation tone

 

 

NO

New Registration finished?

 

 

 

 

 

 

 

YES

 

 

 

 

Release?

NO

 

 

 

 

 

 

 

 

YES

 

 

First

Last

 

First

Last

Hardwired Station No. Hardwired Station No. Hardwired Station No. Hardwired Station No.

First

Last

 

First

Last

Hardwired Station No. Hardwired Station No. Hardwired Station No. Hardwired Station No.

 

 

Confirmation tone

 

 

NO

Release finished?

 

 

 

 

 

 

Return

 

 

NOTES

 

 

 

 

 

1. To release all registered Programmed Station No.'s at one time,

2.

Any one Programmed Station No. cannot be assigned to more

 

(Confirmation tone

 

than one Hardwired Station.

Touch

 

 

 

will be heard.)

 

 

 

10 times

3.

CP DIP switch D-5 must be "ON" to employ this function.

 

 

C. Restriction of programmable station numbering

Each station number can be programmable in the station number series of the exchanges A, B and C that have been determined by the function of the "Selectable First Station Number" (Page 19).

Restriction of station numbers (*1) and (*2)

<Example 1> With personal number(Standard)

<Example 2> Without personal number

<Example 3>

Exchange

Hardwired

Programmed

Exchange

Hardwired

Programmed

Exchange

Station No.

Station No.

Station No.

Station No.

 

 

 

A

200~327

200~469

A

100~227

100~399

A

B

470~597

470~739

B

400~527

400~699

B

C

740~867

740~999

C

700~727

700~999

C

Hardwired Programmed

Station No. Station No.

200~327 200~399

400~527 400~599

600~727 600~799

— 40 —

8. PROGRAMMING DATA TABLE

INITIAL PROGRAMMING

Note. (Mark *)

The first station of each exchange becomes the Programming Station:

Exchange "A" . . . . . . . . . . . . . . . . . . . . . . . . . No. 200 (100)

Exchange "B" . . . . . . . . . . . . . . . . . . . . . . . . . No. 470 (400)

Exchange "C" . . . . . . . . . . . . . . . . . . . . . . . . . No. 740 (700)

Initial Programming of the Exchange

1.Place program switch on front panel of the CP "ON" Dial operation from station No. 200 (100). *

2.Dial tone will be heard (Station No. 200 (100) becomes a programming station)

3.

Confirmation tone will be heard (Clears function group S)

4.

Confirmation tone will be heard (Clears function group A)

5.

Confirmation tone will be heard (Clears function group B)

6.

Confirmation tone will be heard (Clears function group C)

7.

Confirmation tone will be heard (Clears function group D)

8.

Confirmation tone will be heard (Clears function group E)

9.

Confirmation tone will be heard.

 

(Clears personal numbers, single digit dial numbers and remote numbers)

10.

Program necessary functions.

 

(Refer to separate instructions for each function)

11.Place program switch on front panel of the CP in "OFF" position.

12.

(Station No. 200 (100) becomes a normal station.) *

Clearance of Each Function at a Time

Confirmation tone

Establishment of Function on All Stations at a Time

Confirmation tone

— 41 —

< PROGRAMMING DATA TABLE 1 >

Function Table for the System

Function

Function

Registered

Initial programming

Function

code

Note of Registration

Group

data

 

 

 

A

00

 

 

 

Select the head number of stations

Numbering schedules

 

 

in each exchange from among the

40

B

00 followings:

of tie-line system

 

 

100, 200, 300, 400, 500, 600, 700,

 

 

 

 

 

 

800 or 900

 

 

C

00

A/B/C=

200/470/740

or

A/B/C=

100/400/700

Selection of

 

 

0: Without Calling Tone

41

 

1: Single tone (0.2 sec.)

Calling Tone

——

 

2: Calling tone (0.3 sec.)

 

 

 

 

 

S

 

 

 

 

 

 

0: Without Paging

Selection of Paging

 

 

Pre-announcement Tone

 

 

1 : Paging Pre-announcement

Pre-announcement

42

 

 

Tone (1 sec.)

Tone

 

 

 

 

2: Paging Pre-announcement

 

 

 

 

 

 

Tone (2 sec.)

Time-out of

45

 

00: Without Time-out function

conversation

 

01 ~ 99: Length limited (min.)

 

 

Time-out of

46

00: Without Time-out function

Paging call

01 ~99: Length limited (min.)

 

1:

Calling Tone

(0.3sec.)

2:

Paging

Pre-announcement Tone (2 sec.)

00:

Without Time-out

00:

Without Time-out

— 42 —

— 43 —

Exchange of Type

.No Station

Hardwired

Code Function

Function

Group Function

Stations for Table Function

DATA PROGRAMMING <

Executive Priority

 

 

(1)

TABLE

(Highest

Priority)

 

 

 

 

 

Continuous Calling Tone

 

 

 

2>

 

 

 

 

 

 

 

1Stations Allowed Access

to All Call

Stations Allowed Access

to Conference

Automatic Access to Paging

Stations Allowed Access to One Shot Output

Stations Allowed Access

to Make/Break Output

Stations Allowed Access to 1/8

Select (or Decimal) Output

Stations Allowed Access to 4

Decimal Digits Output

Secretary

Station No. *1

Master

Station No. *1

Transferred

Station No. for Group Hunting * 1

Paging Zone No.

Group No. for Group Blocking

Group No. for

Calling Party Indication

Programmed Station No.

—44—

For Paging Unit

For Tie-line Unit

(EX-610)

Exchange of Type

.No Station

CodeFunction

Function

Group Function

(2)Stationsfor Table Function

TABLEDATA<PROGRAMMING

Hardwired

 

 

 

 

Executive Priority

 

 

 

 

(Highest

Priority)

 

 

 

3>

Continuous Calling Tone

 

 

 

 

 

 

 

Stations Allowed Access to All Call

Stations Allowed Access to Conference

Automatic Access to Paging

Stations Allowed Access

to One Shot Output

Stations Allowed Access

to Make/Break Output

Stations Allowed Access to 1/8

Select (or Decimal) Output

Stations Allowed Access to 4

Decimal Digits Output

Secretary

Station No. *1

Master

Station No. *1

Transferred

Station No. for Group Hunting *1

Paging Zone No.

Group No. for Group Blocking

Group No. for

Calling Party Indication

Programmed Station No.

For Paging Unit

For Tie-line Unit

(EX-620)

—45—

Exchange of Type

Hardwired .No Station

Code Function

Function

Group Function

Stations for Table Function

DATA <PROGRAMMING

Executive Priority

 

 

 

(3)

TABLE

(Highest Priority)

 

 

 

 

 

Continuous Calling Tone

 

 

 

4>

 

 

 

 

 

 

Stations Allowed Access

to All Call

Stations Allowed Access to Conference

Automatic Access to Paging

Stations Allowed Access

to One Shot Output

Stations Allowed Access to Make/Break Output

Stations Allowed Access to 1/8

Select (or Decimal) Output

Stations Allowed Access to 4

Decimal Digits Output

Secretary

Station No. *1

Master

Station No. *1

Transferred

Station No. for Group Hunting *1

Paging Zone No.

Group No. for Group Blocking

Group No. for

Calling Party Indication

Programmed Station No.

<PROGRAMMING DATA TABLE 5>

Paging ZoneTable

Function Code 70

Paging Zone

 

First Station No.

Last Station No.

Department

A

 

B

C

 

 

01

08(16)

15(31)

 

 

02

09(17 )

16(32)

 

 

03

10(18)

17(33)

 

 

04

11(19)

18(34)

 

 

05

12(20)

19(35)

 

 

06

13(21)

20(36 )

 

 

07

14(22)

21(37)

 

Station Numbers Table for Calling Party Indication (Lamp Type)

72

Calling Party Indication

First Station No.

Last Station No.

Name

Group No.

1

Function Code

Note.

2

3

4

5

6

7

8

When the indication panel belongs to only one (1) station, you should write the station number in both "First Station No." and "Last Station No." columns.

<PROGRAMMING DATA TABLE 6>

Table for Group Blocking (3 Tables)

Group Blocking for each Group

Group

No.

First Station No.

Last Station No.

Function Code 71

Group Blocking among Groups

 

 

Called Group No.

 

 

Others

81

 

 

Code

Calling

 

 

 

Function

Group No.

 

 

 

EX-3X

EX-2X

 

EX-3X

 

 

Note. : EX-3X: EX-3A, EX-3B, EX-3C, EX-2X: EX-2A, EX-2B

No need to register.

— 46 —

<PROGRAMMING DATA TABLE 7>

Group Blocking for Paging Groups

 

Paging Zone

 

 

 

Paging Group No.

 

Others

 

Department

 

1

 

3

 

5

 

No.

2

4

6

 

All Call

00

 

 

 

 

 

 

 

 

01

 

 

 

 

 

 

 

 

02

 

 

 

 

 

 

 

 

03

 

 

 

 

 

 

 

 

04

 

 

 

 

 

 

 

 

05

 

 

 

 

 

 

 

 

06

 

 

 

 

 

 

 

 

07

 

 

 

 

 

 

 

 

08

 

 

 

 

 

 

 

 

09

 

 

 

 

 

 

 

 

10

 

 

 

 

 

 

 

 

11

 

 

 

 

 

 

 

 

12

 

 

 

 

 

 

 

 

13

 

 

 

 

 

 

 

 

14

 

 

 

 

 

 

 

 

15

 

 

 

 

 

 

 

 

8(16 )

 

 

 

 

 

 

 

 

9(17 )

 

 

 

 

 

 

82

 

10(18 )

 

 

 

 

 

 

 

11(19)

 

 

 

 

 

 

FunctionCode

PagingZones

 

 

 

 

 

 

12(20)

 

 

 

 

 

 

13(21)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

14(22)

 

 

 

 

 

 

 

Individual

23

 

 

 

 

 

 

 

24

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

25

 

 

 

 

 

 

26

27

28

29

30

15(31)

16(32)

17(33)

18(34)

19(35)

20(36)

21(37)

38

39

40

41

42

43

44

45

— 47 —

Summary Table of

Group Blocking (Function Code 71, 81, 82) and Paging Zone (Function Code 70)

Note.

indicates that registration is not necessary,

 

 

 

indicates stations not belonging to any group.

 

 

 

Stations in

No.

 

 

Last Station

21-01

 

Each

 

Paging

 

 

 

Zone

 

 

Calling

(Paging)

Called

First StationNo.

ZoneNo.

Group No.

(Paged and

Stations in

Each Group

Responding)

 

 

Group No.

 

 

First

Last

No.

 

 

Station No.

Station

 

 

Tie-line links

Tie-line links

Other Group

Type of Exchange

 

Dial Operation

 

of Paging Call

 

Paging Zone

All Call Paging

Type of Paging

Station Paging

or PA Paging

 

Dial Operation

 

of Paging Response

 

Stations

not belonging to any Zone

Paging Response

Possible

Impossible

Possible

Zone Paging

Station Paging or PA Paging

— 48 —

PART 2. FUNCTION SELECTION FOR DATA

TRANSMITTING AND RECEIVING UNITS

9.SETTING OF CHANNEL SELECT SWITCH OF TRANSMITTING UNIT (DT-E11) AND WORD SELECT SWITCH OF RECEIVING UNIT (DR-B61)

NOTE

1.Connect the DT-E11 and DR-B61 to Exchange correctly. (Refer to operation manuals of DT-E11 and DR-B61).

2.Set the function select switches (DIP SWITCH) on CP-63 correctly and be sure to enter initial programming and function registration at programming station No.200.

3.Remove the front panel of Data Transmitting Unit (DT-E11) and take out the printed circuit board. Then set the channel select switches located on the printed circuit board, according to the

Connecting Cable YR-802 or YR-806

One Pair Cable

To other DR-B61

Connecting

Cable YR-803

To other

DT-E11

To other RD-B61

CHANNEL SELECT

Switch (SW-1)

necessary functions such as IN/OUT Annunciation, Calling Party Indication etc,and replace in the Unit.

(Refer to 13. Explanation of Data Transmitting Unit Output Data, Page 53).

4.The DT-E11 sends out 512 bit data (16 bit x 32 words) to control relays on Data Receiving Unit (DR-B61). Therefore set the two word select switches on DR-B61, according to necessary output mode. SW-1 is for Relay No.1 to No.16 and SW-2 is for Relay No.17 to No.32. See Page 51 for details.

(Refer to Explanation of Date Receiving Unit Output Channels.)

5.Connecting Cable YR-802 is used for the Rack mounting system. Connecting Cable YR-806 is used for the Standard Cabinet mounting system with only One (1) DT-E11 unit.

WORD SELECT Switch

(SW-1, SW-2)

— 49 —

10. DIP SWITCH TABLE FOR DATA TRANSMITTING AND RECEIVING UNITS

CHANNEL SELECT Switch

WORD SELECT Switch

— 50 —

11. SYSTEM DIAGRAM OF DATA TRANSMITTING AND RECEIVING UNITS

(When the exchanges are connected by means of tie-line.)

 

 

 

 

 

 

Tie-line Unit

TI-62

<Terminal Board>

Stations

 

 

Tie-line Unit

TI-62

(Terminal Board)

Stations

 

Tie-line Unit

 

TI-62

(Terminal Board)

Stations

 

 

 

 

 

 

 

 

 

 

 

YR-810

 

 

 

 

 

 

YR-810

 

 

 

 

 

 

YR-810

 

 

YR-802

 

 

 

 

 

YR-802

 

 

 

 

 

 

YR-802

 

 

 

 

 

 

or

(Exchange A)

 

 

 

or

 

(Exchange B)

 

 

 

or

(Exchange

O

 

 

 

YR-806

 

<Data Receiver

YR-806

 

 

(Data Receiver

YR-806

 

<Data Receiver

 

 

 

 

 

 

 

 

 

 

 

<Data Transmitting Unit>

(Equipment using DR-B61)>

 

(Data Transmitting Unit)

(Equipment using DR-B61))

(Data Transmitting Unit)

(Equipment using DR-B61)>

 

 

 

 

 

 

 

 

 

 

Two

wires

 

 

 

 

 

Two

wires

 

 

 

 

 

Two

wires

 

 

In/Out Annunciation

 

In/Out Annunciation.

 

In/Out Annunciation

 

In/Out Annunciation.

In/Out Annunciation

 

In/Out Annunciation.

YR-803

(500 contacts)

Display Board.

YR-803

 

(500 contacts)

Display Board.

YR-803

(500 contacts)

Display Board.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

VTR, ITV,etc.

 

 

 

 

 

 

VTR, ITV, etc.

 

 

 

 

 

 

(1)

One-shot Make Output

 

 

 

(1 )

One-shot Make Output

 

 

(1)

One-shot Make

Output

 

 

 

(50 contacts)

Prescription Display

 

 

(50 contacts)

Prescription Display

 

(50 contacts)

Prescription Display

 

 

 

 

 

 

 

 

 

 

 

 

 

 

(2)

Make-Break

Output

 

Board, etc.

 

 

(2) Make-Break Output

 

Board, etc.

 

(2) Make-Break

Output

 

Board, etc.

 

 

 

 

 

 

 

 

 

 

 

 

(100

contacts)

 

 

 

 

(1 00

contacts)

 

 

 

(1 00

contacts)

 

 

(3)

8-Selectable Make Output

or Room Condition Indication.

 

(3)

8-Selectable

Make Output

or Room Condition Indication.

(3)

8-Selectable

Make

Output

or Room Condition Indication.

Destination Indication.

 

Destination

Indication.

Destination

Indication.

 

 

(9

units)

 

 

 

(9

units)

 

 

 

(9

units)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

(4)

Decimal Output (9

units)

 

 

 

(4)

Decimal Output (9

units)

 

 

(4)

Decimal Output

(9

units)

 

 

(5)

4 Decimal Digits Output

 

 

 

(5)

4 Decimal Digits Output

 

 

(5)

4 Decimal Digits Output

 

 

 

 

(9 units)

Room Condition Indication.

 

 

 

(9 units)

Room Condition Indication.

 

 

 

(9 units)

Room Condition Indication.

YR-803

 

 

 

Destination

Indication, etc.

YR-803

 

 

 

 

Destination

Indication, etc.

YR-803

 

 

 

 

Destination

Indication, etc.

(6)

Pager Control (64 pager)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Prescription

Display

 

 

 

 

 

Prescription

Display

 

 

 

 

 

Prescription

Display

 

 

 

 

Board, etc.

 

 

 

 

 

 

Board, etc.

 

 

 

 

 

 

Board, etc.

 

Calling Party Indication.

Calling Party Indication.

Lamp Type.(1 )

Lamp Type,(1 )

4

 

4

4

units

 

units

units

YR-803

YR-803

YR-803

 

Calling Party Indication.

Calling Party Indication.

Calling Party Indication.

Lamp Type.(2)

Lamp Type. (2)

Lamp Type.(2)

4

4

4

units

units

units

— 51 —

12. EXPLANATION OF DATA TRANSMITTING UNIT OUTPUT CHANNELS

CHANNEL SELECTION

FUNCTIONS

IN/OUT Annunciation

DESCRIPTION

Personel in and out registration can be accomplished at any Master station by using personal numbers. Max. 500 IN/OUT annunciations may be done. (All the 3 exchanges provided the same indication)

APPLICATION

• IN/OUT Annunciation

(1 ) One-shot Make Output

(50 contacts)

(2)Make/Break Output (100 contacts)

(3)8 Selectable Make Output (9 unit blocks)

(4)Decimal Output

(9 unit blocks)

(5)4 Decimal digits output (9 unit blocks)

(6) Pager Control Output

(64 contacts)

Calling Party Indication (1)

(One Station; One Lamp)

Calling Party Indication (2)

(One Station; One Lamp)

One-shot make contacts can be avail-

able at any Master station.

*1

Make/Break contacts can be available at any Master station. *1

One contact out of 8 selectable make outputs is obtained. "Clear" operation makes ail 8 relays break. *1

10 Selectable Decimal Outputs are available with 7 segments LEDs. *1

Indicate by 7 segments LEDs. *1

Make output (64 contacts) are available for pager control. *2

Max. 120-Calling station numbers can be indicated when designated called station with Display Board is called. The numbers of called stations having an indication panel can be programmed at No. 200 station. (Only the calling stations within the same exchange can be indicated by a lamp)

Note.

*1.Each exchange has an independent control system, and it is impossible to control the Data Transmitting Unit of the other exchange form the station connected to the different exchange.

*2. Can only be connected to the exchange A (Station No. 200 ~ 327). It is impossible to call the pagers from any station not connected to the exchange A. However, the response to a pager call is possible from any station regardless of the exchange it is connected to.

ITV camera selection

VTR control

Door Remote

IN/OUT Annunciation

Destination indication

VTR control

Room condition indication.

Prescription annunciation

Pager

The group number of called station (s). No. 1 ~ 4

The group number of called station (s). No. 5 ~ 8

— 52 —

13. EXPLANATION OF DATA RECEIVING UNIT OUTPUT DATA

13-1 Channel 0 (CH. 0) In/Out Annunciation

(Dial Operation)

(Relay Make) XXX: 000 ~ 499 (500 Contacts )

Personal Number Registration

Personal Number Cancellation

(Relay Break)

CHANNEL SELECT Switch

Each Relay Output shows last 3 digits (xxx) of Personal Number

WORD SELECT Switch

— 53 —

13-2 Channel 1 (CH. 1) (1)

One-shot Make Output (50 contacts)

(2)

Make/Break Output (100 contacts)

(3) 8-Selectable Make Output (9 units)

(4)

Decimal Output (9 units)

(5)

4 Decimal Digits Output (9 units)

(6) Pager Control Output (64 contacts)

CHANNEL SELECT Switch

(Example)

(1)One-shot Make Output

(2)Make/Break Output

(3) 8-Selectable Make Output

Unit No. 4 Condition "1"

Unit No. 6 Condition "8"

(4) Decimal Output (9 units)

Unit No. 8 Condition "9"

Binary Negative

Logic Output

(5)4 Decimal Digits Output

Unit No. 6

Unit No. 7

Binary Output

Negative Logic

(6)Pager Control Output

Pager No. 47 is being called.

WORD SELECT Switch

— 54 —

13-3 Channel 2 (CH. 2) Calling Party Indication (Lamp Type) (1)

Each "Calling Station" or "Waiting Station" is shown by Each Lamp of Indication.

 

Total Number of Station with Indications: 4 Stations (Groupsl/Channel [8 Stations

(Groups)/2 Channels]

Total Number of Calling Stations: Max.

120 Stations/Each Indication

 

Data Receiver

Relay Output No.

Station No.

with Indication

CHANNEL SELECT Switch

Group 1

Group 2

Group 3

Each Relay Output shows

Group 4

"Calling Station No."

 

Note:

shows the Head of a Slide Switch

WORD SELECT Switch

 

 

— 55 —

13-4 Channel 3 (CH. 3) Calling Party Indication (Lamp Type) (2)

Each "Calling Station" or "Waiting Station" is shown by Each Lamp of Indication.

Total Number of Station with Indications: 4 Stations (Groupsl/Channel [8 Stations (Groups)/2 Channels]

Total Number of Calling Stations: Max. 120 Stations/Each Indication

CHANNEL SELECT Switch

Each Relay Output shows "Calling Station No."

WORD SELECT Switch

— 56 —

Appendix. Instructions for building the CP-63 in the EXES-5000

1. The CPU-55/56 differ from the CP-62/63 in dial operation.

Function

CPU-55

CPU-56

CP-62

CP-63

Continuous Calling Tone

One-touch Response

8 Selectable Make Output

X: 1 ~ 9, Y: 0~ 7

X: 1 ~ 9, Y: 1 ~ 8, 0 (Clear)

X: 1 ~ 9, Y: 1 ~ 8, 0 (Clear)

2.Set the DIP switch SW-E-5 (change-over of Privacy and Continuous Calling Tone) to OFF (Privacy). Set the other DIP switches according to the necessity.

3.The "Automatic Access to Paging" function is not available from the EXES-5000 system. You, therefore, need not program the "Automatic Access to Paging" function (Function Code No. 54) referred to in Function Code Table for Station NO No. 200 Programming.

4.Module units necessary for the tie-line system.

Function

Exchange "A"

Exchange "B"

Possible or

Reason

Necessary module units

impossible

 

 

 

 

 

 

 

 

Possible

 

 

 

 

 

 

 

• It is impossible to use both the

All functions

 

 

 

 

CPU-56 and the CP-63 in the

 

 

 

 

 

same system.

 

 

 

Impossible

 

 

 

 

 

Possible

 

• DLU-52

 

 

 

 

 

or

Conversation

 

 

Impossible

2 voice switch passes

• DL-62, OC-62

Possible

1 voice switch passes

Impossible

3 voice switch passes

Conference

 

Possible

1 voice switch passes

Note.

 

It is impossible to use both the CPU-56 and the CP-63 in the same system.

• CL-62, DL-62, OC-62

1.To ensure the complete speech functions (perfect simultaneous speech, calls and responses made by means of a handset, etc.) that the stations of EXES-6000 system can have, 2-wire stations as well as the LM-62 is necessary.

2.The exchange using the frame FR-510 or FR-520 allows for no tie-line connection to the other exchange. The tie-line connections are only possible among the exchanges using the frame FR-510A, FR-520A, FR-510B, FR-520B, FR-610 or FR-620.

3.For the following module units, you may use whichever you proper: SGD-52A and SG-62 (the SG-62 is necessary when the LM-62 is used.)

PIU-52A and PI-62 TI-52 and TI-62

4.When the CP-63, OC-62 and DL-62 are used in the tie-line system, the speech link of the calling exchange is in the full duplex mode, while voice switches cause the speech link of the called exchange to be in the automatic alternative speech mode.

— 57 —

TOA ELECTRIC CO, LTD.

KOBE, JAPAN