TOA Electronics CP-66 User Manual

2.27 Mb

EXES-6OOO CP-66

INTERCOM SYSTEM

CP-66

Functions and

Operating Instructions

TOA Corporation

Contents

Introduction to the "Functions and Operating

Instructions" for stations for EXES-6000 . . . . . . . . . . . . 1

Chapter 1. Basic Functions, Their Operating Procedures and

All Functions

1.

Stations . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

. . . 2

2.

Speech Functions . . . . . . . . . . . . . . . . . . . . . . .

. . . 3

3. Station Operation (PV Type)

 

 

1)

Handset Master Station (TL-600M/610M/620M)

. . . 4

 

2) Handset Substation (TL-600S) . . . . . . . . . . . .

. . . 4

 

3)

Hands-free Master Station

 

 

 

(HF-210M/210MB/670M/HS-670). . . . . . . . . . . . . . .

. . . 5

 

4) Hands-free Substation . . . . . . . . . . . . . . . . . . . . .

. . . 6

 

5)

Hands-free/Handset Master Station

 

 

 

(HF-200M/200MB/250M) . . . . . . . . . . . . . . . . . . . .

. . . 7

 

6)

Hands-free/Handset Substation . . . . . . . . . . . . . . .

. . . 8

 

7)

Hands-free/Handset Master Station with Auto-dialer

 

 

(HF-250M) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

. . . 9

 

8)

Door Station (HF-640S) . . . . . . . . . . . . . . . . . . . .

. . . 11

 

9)

Talk-back unit (TK-20) . . . . . . . . . . . . . . . . . . . . .

. . . 11

4.Station Operation (NP Type)

1)Handset Master Station (TL-600M/610M/660M) . . . 11

2)

Handset Substation (TL-600S) . . . . . . . . . . . . . .

11

3)

Hands-free Master Station

 

 

(HF210M/210MB/670M/HS-670) . . . . . . . . . . . . . . .

12

4)

Hands-free Substation . . . . . . . . . . . . . . . . . . . . . . .

13

5)

Hands-free/Handset Master Station

 

 

(HF-200M/200MB/250M) . . . . . . . . . . . . . . . . . . . . .

14

6)

Hands-free/Handset Substation . . . . . . . . . . . . . . .

15

7)

Hands-free/Handset Master Station with Auto-dialer

 

(HF-250M) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

16

8)

Door Station (HF-640S) . . . . . . . . . . . . . . . . . . . . . .

17

9)

Talk-back unit (TK-20) . . . . . . . . . . . . . . . . . . . . . . .

17

5. Functions: EXES-6000 CP-66 . . . . . . . . . . . . . . . . . . . .

18

Chapter 2. Functions and Operating Procedures of Single

Exchange System

1. EXES-6000 CP-66 Summary of Dial Operations

 

(For Single Exchange) . . . . . . . . . . . . . . . . . . . . . .

20

2. Description of Each Function

 

1)

Camp-On-Busy . . . . . . . . . . . . . . . . . . . . . . . . .

24

2)

Busy Call Back . . . . . . . . . . . . . . . . . . . . . . . . .

24

3)

Privacy (PV Type) . . . . . . . . . . . . . . . . . . . . . .

25

4)

Camp-On-Privacy (PV Type) . . . . . . . . . . . . . . . .

26

5)

Press-To-Talk . . . . . . . . . . . . . . . . . . . . . . . . . .

26

6)

Mic Off (PV Type/NP Type) . . . . . . . . . . . . . . .

27

7)

Press-To-Talk Control . . . . . . . . . . . . . . . . . . . .

27

8)

Single Digit Dialing . . . . . . . . . . . . . . . . . . . . . .

28

9)

Master Sub Relationship . . . . . . . . . . . . . . . . . . .

29

10)

Automatic Access To Paging . . . . . . . . . . . . . . . .

29

11)

Personal Number Call . . . . . . . . . . . . . . . . . . . .

30

12)

Continuous Calling Tone . . . . . . . . . . . . . . . . . .

31

13)

Remote Response . . . . . . . . . . . . . . . . . . . . . . .

32

14)

Call Transfer, Paging during Normal Call . . . . . . . .

33

15)

Group Hunting . . . . . . . . . . . . . . . . . . . . . . . . .

34

16)

Secretary Transfer (PV Type/NP Type) . . . . . . . .

35

17)

Call Forwarding . . . . . . . . . . . . . . . . . . . . . . . .

38

18)

Priority . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

39

19)

Executive Priority . . . . . . . . . . . . . . . . . . . . . . .

39

20)

Highest Executive Priority . . . . . . . . . . . . . . . . .

40

21)

Conference . . . . . . . . . . . . . . . . . . . . . . . . . . .

41

22) Paging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

42

23) Other Paging Modes . . . . . . . . . . . . . . . . . . . . .

43

24)

How to Select the Paging Area and Make the

 

 

Paging Call . . . . . . . . . . . . . . . . . . . . . . . . . . .

44

25)

All-Call Paging and Individual Zone Paging . . . . . .

45

26)

Combination Paging . . . . . . . . . . . . . . . . . . . . .

46

27)

Emergency All-Call Paging . . . . . . . . . . . . . . . . .

48

28)

Priority Station Paging . . . . . . . . . . . . . . . . . . . .

49

29)

Personal Number Paging . . . . . . . . . . . . . . . . . . .

50

30)

Selectable First Station Number . . . . . . . . . . . . .

51

31)

Programmable Station Numbering . . . . . . . . . . . .

51

32)

Group Blocking . . . . . . . . . . . . . . . . . . . . . . . .

52

33)

Programmable Restricted Access for Stations . . . .

53

34)

Selectable Calling Tone . . . . . . . . . . . . . . . . . . .

54

35)

Selectable Paging Pre-paging Tone

 

 

Duration . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

54

36)

Time-Out of Conversation . . . . . . . . . . . . . . . . .

54

37)

Time-Out of Paging Call . . . . . . . . . . . . . . . . . . .

54

38)

In/Out Annunciation . . . . . . . . . . . . . . . . . . . . .

55

39)

Destination Annunciation Indication . . . . . . . . . .

56

40)

Calling Party Indication [Lamp Type] . . . . . . . . .

57

41)

Calling Party Indication [Numerical Type] . . . . . .

58

42)

Conversation Partner Indication [Lamp Type] . . . .

59

43)

Pocket Pager . . . . . . . . . . . . . . . . . . . . . . . . . .

60

44)

General Purpose Control . . . . . . . . . . . . . . . . . .

61

45)

Simplified Paging . . . . . . . . . . . . . . . . . . . . . . .

62

46)

Clear Entry and Conversation Over . . . . . . . . . . .

62

Chapter 3. Functions and Operating Procedures of Tie-Line

 

 

System

 

 

 

 

1. Tie-Line Connections of Exchanges . . . . . . . . . . .

63

17)

Paging . . . . . . . . . . . . . . . . . . . . . . . . . . . .

83

2.

Restrictions Resulting from Tie-Line Connection . .

65

18)

How to Select the Paging Area and Make the

 

 

Paging Call

84

3.

EXES-6000 CP-66 Summary of Dial Operations

 

 

 

19) All-Call Paging and Individual Zone Paging . . . . 85

 

(For Tie-Line System)

66

 

20)

Selectable First Station Number of Each

 

 

 

 

 

 

4. Description of Each Function

 

 

Exchange . . . . . . . . . . . . . . . . . . . . . . . . . .

86

 

1) Camp-On-Busy . . . . . . . . . . . . . . . . . . . . . . .

68

21)

Programmable Station Numbering . . . . . . . . . .

87

 

2) Busy Call Back . . . . . . . . . . . . . . . . . . . . . . .

68

22) Group Blocking . . . . . . . . . . . . . . . . . . . . . .

88

 

3)

Privacy (PV Type) . . . . . . . . . . . . . . . . . . . .

69

23)

Programmable Restricted Access for Stations . . .

90

 

4)

Camp-On-Privacy (PV Type) . . . . . . . . . . . . .

70

24)

Selectable Calling Tone . . . . . . . . . . . . . . . . .

91

 

5)

Press-To-Talk . . . . . . . . . . . . . . . . . . . . . . . .

70

25)

Selectable Paging Pre-paging Tone

 

 

6)

Single Digit Dialing . . . . . . . . . . . . . . . . . . . .

71

 

Duration . . . . . . . . . . . . . . . . . . . . . . . . . . . .

91

 

7)

Master Sub Relationship . . . . . . . . . . . . . . . .

72

26)

Time-Out of Conversation . . . . . . . . . . . . . . . .

91

 

8)

Automatic Access To Paging . . . . . . . . . . . . . .

72

27) Time-Out of Paging Call . . . . . . . . . . . . . . . . .

91

 

9)

Personal Number Call . . . . . . . . . . . . . . . . . .

73

28)

In/Out Annunciation . . . . . . . . . . . . . . . . . . .

92

 

10)

Continuous Calling Tone . . . . . . . . . . . . . . . . .

74

29)

Calling Party Indication [Lamp Type] . . . . . . .

93

 

11)

Remote Response . . . . . . . . . . . . . . . . . . . . .

75

30) Conversation Partner Indication [Lamp Type] . .

94

 

12)

Call Transfer, Paging during Normal Calls . . . . . .

76

31)

Pocket Pager . . . . . . . . . . . . . . . . . . . . . . . .

95

 

13)

Group Hunting . . . . . . . . . . . . . . . . . . . . . . .

77

32)

General Purpose Control . . . . . . . . . . . . . . . .

96

 

14)

Secretary Transfer (PV Type/NP Type) ......

78

33)

Simplified Paging . . . . . . . . . . . . . . . . . . . . .

98

 

15) Highest Executive Priority . . . . . . . . . . . . . . .

81

34) Clear Entry and Conversation Over . . . . . . . . .

98

 

16)

Conference . . . . . . . . . . . . . . . . . . . . . . . . .

82

 

 

 

Chapter 4. Functions and Operating Procedures of

 

 

External Interface System

 

 

1. Description of Each Function

 

5) Tie-Line Interface . . . . . . . . . . . . . . . . . . . . .

103

1)

External Interface . . . . . . . . . . . . . . .

. . . . . . 99

6)

Selectable Paging . . . . . . . . . . . . . . . . . . . . .

106

2)

OD Interface . . . . . . . . . . . . . . . . . . .

. . . . . 100

7)

Speech Message . . . . . . . . . . . . . . . . . . . . . .

111

3)

LD Interface . . . . . . . . . . . . . . . . . . .

. . . . . 100

8)

Background music (BGM) . . . . . . . . . . . . . . .

113

4)

CB Interface . . . . . . . . . . . . . . . . . . .

. . . . . 101

9)

Alarm . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

114

 

 

 

10)

Time signal . . . . . . . . . . . . . . . . . . . . . . . . .

114

Introduction to the "Functions and Operating Instructions" for stations for EXES-6000

This handbook explains the functions and operating procedures of stations for TOA's EXES-6000 Intercom

System.

This handbook is comprised of the following 4 chapters:

Chapter 1. Basic functions, their operating procedures and all functions.

Chapter 2. Functions and operating procedures of single exchange system.

Chapter 3. Functions and operating procedures of tieline system.

Chapter 4. Functions and Operating procedures of External Interface system.

Refer to Chapters 1, 2 and 4 for single exchange system and to Chapters 1, 3 and 4 for tie-line system.

Please note that performances of some functions are restricted in the tie-line system.

You need not read all the instructions given in this handbook but it is necessary to read the instructions on those functions employed in your system. The following guidelines will help you select the pages that you should read.

Selecting different functions made available by placing the Privacy Switch in the "ON" position

The EXES-6000 System is designed to allow either "PV" type operation (the system having Privacy function) or "NP" type (without Privacy function) to be selected by turning on or off a switch inside the exchange. It is imposisble to make one station the "NP" type and another the "PV" type in the same system.

The function provided when the Privacy switch is in the ON position is different between the "PV" and the "NP" type. Therefore, read the page marked if your system

is of the "PV" type and the Page

if it is of the

"NP" type.

"PV" Type and "NP" Type

Type

 

Definition

Description

PV Type

 

System having

1. Privacy tone

 

 

 

Privacy function

With the Privacy switch in

 

 

 

the ON position, a brief

 

 

 

Privacy tone sounds and *1

 

 

 

any incoming call is refused.

NP Type

System having

 

 

 

no Privacy func-

 

 

 

tion

 

 

 

 

 

 

 

 

Note.

1.Continuous calling tone

A station with the Privacy switch may be called by the continuous calling tone when its Privacy switch is placed in the ON position.

One touch dialing any key

through

other than the

key or picking up the handset stops the calling tone and the stations is made ready to initiate the response to the call. *2

2.The Handset Master station without Privacy switch may be called by the continuous calling tone. Picking up the handset stops the calling tone

and allows the conversation.

*1. Before you use a PV-type handset station, it is necessary that you first register that station by station No.200 programming.

*2. By programming, the continuous calling tone function may be made available to specific stations with the Privacy switch in the OFF position.

In this event, touch dialing any key ( through other than the key stops the calling tone and permits conversation.

This feature may be employed in the industrial type of station (Model HF 670M) or in the "PV" type system that needs to be continuously called.

— 1 —

Chapter 1

Basic functions, their operating procedures and all functions

1. Stations

(1) HF-200M/HF-200MB

Desk/surface-mounted handsfree/handset master station

(2) HF-210M/HF-210MB

Desk/surface-mounted handsfree master station

(3) TL-600M

Desk/surface-mounted handset operated master station

(4) TL-600S

Desk/surface-mounted handset operated substation

(5)TL-610M

Desk-top type handset operated master station

(6) TL-620M

Surface-mounted handset operated master station

(7) HF-640S

Door station

(8) HF-670M/HS-670

HF-670M

Industrial-use handsfree master station

HS-670

Handset unit for HF-670M

(9) HF-250M

Desk/surface-mounted handsfree/handset master station

(10)TK-20

Talk-back unit

- 2 -

2. Speech functions

Either "PV" Type (the system with Privacy function) or "NP" Type (without Privacy function) mode should be selected for the whole intercom system.

When Privacy Switch (SW) of station is turned ON, privacy tone is available in "PV"Type system, while continuous calling

tone is available in "NP" Type system.

Functions

Dialing

One-Touch Dialing

Calling

Dialing after picking up handset and comfirming dial tone

Calling by picking up handset

Voice Calling

Voice

Hands-free calling and conversation

Continuous calling tone response by one-touch dialing

(No. 200 programming) *1

Privacy

Receiving

Continuous calling tone picking up response (in

Privacy mode)

Continuous calling tone one-touch response (in

Privacy mode)

Voice switch conversation

Simplex conversation by press-to-talk key

Speech

Methods

Fully duplex conversation

Descriptions

Calls are made by touching dial key.

Even when the Privacy SW is on, calling is possible.

Substations can make a call to designated master stations by one-touch dialing. Calling is possible even when the Privacy

SW is on.

Calls can be made by touching dial key after picking up handset, and confirming dial tone is heard.

Substations can make a call to designated master stations by simply picking up the handset.

When called by continuous calling tone or privacy tone, voice can be sent by pressing bar.

By one-touch dialing keys, after a brief calling tone hands-free conversation can get started.

One-touch dialing keys transmits a continuous calling tone.

Hands-free Conversation can get started when called party depresses, the key.

When calls are unwanted, turn ON Privacy SW. Then a brief privacy tone sounds when called. By turning off Privacy SW or touching any key or by picking up a handset, conversation becomes possible.

When called by continuous calling tone, conversation is possible by picking up handset.

Calls can be answered by dialing the. key without picking up handset when called by continuous calling tone.

Two-way conversation is achieved automatically when two parties speak in hands-free mode.

One-way conversation is made by a party who presses Releasing the bar will reverse the one-way conversation flow.

Fully duplex conversation is made when at least either party uses a handset.

Stations *2

Without

With

Privacy SW

Privacy SW

HF-670M

HF-250M

 

HF-200M,

 

200MB

 

HF-210M,

 

210MB

HF-640S

 

 

TL-610M

HF-250M

TL-620M

HF-200M,

TL-600M

200MB

TL-600S

 

 

All stations except

HF-640S

HF-640S HF-670M

HF-640S HF-670M

TL-610M TL-620M TL-600M/S

HF-640S HF-670M

HF-640S HF-670M

TL-610M TL-620M TL-600M/S HF-640S HF-670M

HF-250M HF-200M, 200MB HF-210M, 210MB

HF-250M HF-200M, 200MB HF-210M, 210MB

HF-250M HF-200M, 200MB HF-210M, 210MB

HF-250M HF-200M, 200MB

HF-250M HF-200M, 200MB

HF-210M 210MB

HF-250M HF-200M, 200MB HF-210M, 210MB

HF-250M HF-200M, 200MB HF-210M, 210MB

HF-250M HF-200M, 200MB HF-210M, 210MB

Privacy

SW

ON/OFF

ON/OFF

ON

ON

ON/OFF

OFF

OFF

ON

ON

ON/OFF

ON/OFF

ON/OFF

*1 This function may be employed for the industrial type of station (Model HF-670M) or in the "PV" system that needs to be continuously called. *2 Before you use a PV-type handset station, it is necessary that you first register that station by station No. 200 programing.

— 3 —

3. Station Operation (PV Type)

1) Handset Master Station

PV Type

Model TL-600M/610M/620M

Handset

Speaker volume switch

Dial keys

In-use lamp

TL-600M

Handset

Cord

Loudspeaker

In-use lamp

Keyboard

TL-610M

<Making a call >

1.Pick up the handset and dial the desired station number after hearing a dial tone.

2.Start conversation after the calling tone stops.

3.When you hear a busy tone that indicates the party you call is on another line, you can camp on the line by simply waiting without hanging up the handset.

As soon as the line becomes free, your call is automatically connected.

4.While the continuous calling tone is sent, you can

break in on the calling tone by continuously depressing the key to make a voice call through the station speaker of the called party.

TL-620M

5.Hang up the handset or depress the key to termi- nate the conversation.

<Responding to a call >

6.When you are called by the continuous calling tone or paged through your station speaker, respond to the call by picking up the handset.

Note.

1.The sound volume of the calling tone may be adjusted by means of a 2-stage volume selector. (SP. VOL) switch.

2.When using this function in the PV type system having the Privacy function, No. 200 programming is

required.

2) Handset Substation

Model TL-600S

PV Type

Handset

Speaker volume switch

In-use lamp

<Making a call >

1.Picking up the handset makes a call to the designated station.

2.Start conversation after the calling tone stops.

3.When you hear a busy tone that indicates the party you call is on another line, you can camp on the line by simply waiting without hanging up the handset. As soon as the line becomes free, your call is automatically connected.

4.While the continuous calling tone is sent, you can

break in on the calling tone by continuously depress-

ing the key to make a voice call through the station speaker of the called party.

5. Hang up the handset to terminate the conversation.

<Responding to a call>

6.When you are called by the continuous calling tone or paged through your station speaker, respond to the call by picking up the handset.

Note.

1.The sound volume of the calling tone may be adjusted by means of a 2-stage volume selector. (SP. VOL) switch.

2.When using this function in the PV type system having the Privacy function, No. 200 programming is required.

— 4 —

3) Hands-free Master Station

Model HF-210M/210MB/670M/HS-670

 

PV Type

 

 

 

 

 

 

 

 

 

Speaker

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

In-use lamp

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Privacy switch

 

 

 

 

 

 

Dial keys

 

Speaker volume

 

 

 

Microphone

 

switch

 

 

 

HS-670

HF-210M

HF-670M

 

<Making a call >

1.Dial the desired station number regardless of whether the Privacy switch of your station is in the ON position or OFF position.

2.Start conversation after the calling tone stops.

3.When the line is busy, a busy tone is heard and you can camp on the line by simply waiting. As soon as the line becomes free, your call is automatically connected.

4.While a continuous calling tone or Privacy tone is

being sounded, you can make a voice call by continuously depressing the key.

5.When the party you call is in a high noise level area,

your continuously depressing the key allows one-way conversation to that party. As long as you

depress the key, your voice has dominance and releasing the key will reverse the one-way conversation from that party to you.

6.To terminate the conversation, depress the key.

<Responding to a call >

[Privacy switch is OFF.]

7.Respond to the call after the calling tone stops. [Privacy switch is ON.]

8.A brief Privacy tone sounds from your station each time there is an incoming call and all incoming calls

are refused.

To respond touch dial any key other than the key while the line is connected between you and the calling party.

Note.

1.The sound volume of the speaker may be adjusted by means of the 2-stage volume selector (VOL) switch.

2.With no speaker built inside, the HF-670M needs to be connected to an external speaker. Also, the

HF-650M is fitted with no Privacy switch.

3.When the HF-670M is connected to the handset unit HS-670, lifting up the handset responds to call.

— 5 —

4) Hands-free Substation

PV Type

 

Speaker

 

In-use lamp

Privacy switch

 

Dial keys

Speaker volume

Microphone

switch

 

HF-210M+YC-200

HF-210M+YC-240S

< Making a call >

1.Touching the key makes a call to the designated station regardless of whether the Privacy switch on the calling station is in the ON position or OFF position.

2.Start conversation after the calling tone stops.

3.When the line is busy, a busy tone is heard and you can camp on the line by simply waiting. As soon as the line becomes free, your call is automatically connected.

4.While a continuous calling tone or Privacy tone is

being sounded, you can make a voice call by continuously depressing the key.

5.When the party you call is in a high noise level area,

your continuously depressing the key allows one-way conversation to that party. As long as you

depress the key, your voice has dominance and releasing the key will reverse the one-way conversation from that party to you.

6. To terminate the conversation, depress the key.

<Responding to a call >

[Privacy switch is in the OFF.]

7.Respond to the call after the calling tone stops. [Privacy switch is in the ON.]

8.A brief Privacy tone sounds from your station each time there is an incoming call, and all incoming calls are refused.

To respond, touch dial the or key while the line is connected between you and the calling party.

Note.

1.The sound volume of the speaker may be adjusted by means of the 2-stage volume selector (VOL) switch.

2.The No.200 programming (Master/Sub relationship) must be performed in the exchange to call a specified master station.

— 6 —

5) Hands-free / Handset Master Station Model HF-200M/200MB/250M (With Auto-Dialer)

PV Type

 

Speaker

 

Handset

 

 

 

In-use lamp

 

 

Privacy switch

 

 

Speaker volume switch

 

Dial keys

Microphone

 

 

 

 

HF-200M

HF-250M

< Making a call >

1. Hands-free conversation may be made by simply touch dialing the station number you wish to call.

2.When you wish to use the handset, pick it up, then touch dial the station number you wish to call, or reverse the order.

3.Start conversation after the calling tone stops.

4.When you hear a busy tone that indicates the party you call is on another line, you can camp on the line by simply waiting. As soon as the line becomes free, your call is automatically connected.

5.In the event that the party you are calling does not respond and the continuous calling tone is still heard from your station, or when the station of that party is in the Privacy mode and the Privacy tone is sound-

ed, you can break in on the calling tone by continu-

ously depressing the key to make a voice call through the station speaker of the called party.

6.During hands-free conversation, when the person you are talking to is in a high noise level area,

(1) Pick up the handset to talk or (2) depress the key continuously for one-way conversation to that party. As long as the key is depres-

sed, your voice has dominance, and releasing the key will reverse the one-way conversation

from that party to you.

7.To terminate the conversation, hang up the handset or depress the key.

<Responding to a call >

[Privacy switch is in the OFF.]

8.Respond to call after the calling tone stops.

[Privacy switch is in the ON.]

9.A brief Privacy tone will sound from the called station each time it receives an incoming call and all

incoming calls are refused.

To respond, depress any key other than the key or pick up the handset

while the line is still connected between the called and the calling stations. These stations are, however, automatically disconnected from the speech path after approximately 10 seconds from call establishment if no response is made the called party.

Note.

The sound volume of the loud speaker may be adjusted by means of the 2-stage volume selector (VOL) switch.

— 7 —

6) Hands-free / Handset Substation

PV Type

 

Speaker

Handset

 

 

In-use lamp

 

Privacy switch

 

Speaker volume switch

Dial keys

Microphone

 

HF-200M+YC-200

HF-200M+YC-230S

<Making a call >

1.For hands-free conversation, touching the key makes a call to the designated station regardless of whether the Privacy switch on your station is in the

ON position or OFF position.

2.When you wish to use the handset, pick it up, then

touch dial the key to make a call or reverse the order.

3.Start conversation after the calling tone stops.

4.When you hear a busy tone that indicates the party you call is on another line, you can camp on the line by simply waiting. As soon as the line becomes free, your call is automatically connected.

5.In the event that the party you are calling does not respond and the continuous calling tone is still heard from your station, or when the station of that party is in the Privacy mode and the Privacy tone is sound-

ed, you can break in on the calling tone by continu-

ously depressing the key to make a voice call through the station speaker of the called party.

6.During hands-free conversation, when the person you are talking to is in a high noise level area,

(1)Pick up the handset to talk or (2) depress the

key continuously for one-way conversation to that party. As long as the key is depressed, your voice has dominance, and releasing the key will reverse the one-way conversation from that party to you.

7.To terminate the conversation, hang up the handset or depress the key.

<Responding to a call >

[Privacy switch is in the OFF.]

8.Respond to call after the calling tone stops. [Privacy switch is in the ON.]

9.A brief Privacy tone will sound from your station each time it receives an incoming call and all in-

coming calls are refused.

To respond, depress the key or pick-up the

handset while the line is still connected between your station and the station calling. These 2 stations are, however, automatically disconnected from the speech path after approximately 10 seconds from call establishment if no response is made by you.

Note.

1.The sound volume of the load speaker may be adjusted by means of the 2-stage volume selector (VOL) switch.

2.The No.200 programming (Master/Sub relationship) must be performed in the exchange to call a specified master station.

— 8 —

7) Hands-free/Handset Master Station with Auto-Dialer

Model HF-250M

 

In-use lamp

Liquid crystal

 

Handset

display (LCD)

REGISTER switch Rear side

 

 

 

Station number card

 

Loud speaker

 

 

key

 

 

 

 

Auto-Dialer keys

 

 

Speaker volume switch

key

 

 

key

key

key

<Making a call >

1.Place the auto-dialer registration (REGISTER) switch in the OFF position.

2.16 registrations are possible with 8 keys by changing over the A/B page selection key.

You can call any one of pre-registered stations by touch-dialing the auto-dialer key.

3.For making a call and responding to a call without using the auto-dialer, refer to "5) Hands-free/Handset Master

Station HF-200M/200MB/250M (With Auto-Dialer)".

<Auto-dialer registration >

Two station numbers can be registered by each auto-dialer key.

Operation

1. Switch the (REGISTER) switch ON.

Indication on the liquid crystal display

 

 

 

 

 

or

2.

Press

the

key

until

is

 

appeared on the LCD display.

 

 

Press it three times for

and

 

twice for

 

 

 

3.

Press

the

auto-dialer

key (

)to

select the station number to be registered.

Indication on the liquid crystal display.

4.Press the A/B page selector key to select either A or B page.

5.Station numbers can be consecutively registered by maximum 50 digits using the dial keys.

Indication on the liquid crystal display.

6.Press the key, and the dialled numbers are memorized.

7.Repeat steps (3) through (6) to register other station numbers.

8.Switch the (REGISTER) switch OFF after completing registration.

<Liquid crystal display >

A. Indication on the liquid crystal display in conjunction with the DT-E70 is changed with three status.

1.When waiting

Privacy mode status, page selection and time indication

Displays "PV"status when the privacy key is set to ON.

Displays either A or B page of the autodialer.

2.When dialling for paging

Dial monitor indication

3.When responding to a call

Calling station number

Waiting station number

Number of waiting stations

Note. For detailed indication mode, refer to "Calling Party Indication (Numerical Type)"

B.Indication on the liquid crystal display is changed into two status when the HF-250M is used solely.

His-own-station number

1.When waiting

Privacy mode status, page selection and his-own-station number

2.When dialling for paging

Dial monitor indication

Note. For registration to use the liquid crystal display, refer to "Operating Instructions of the HF-250M and DT-E70".

— 9 —

8) Door Substation

Model HF-640S

PV Type

HF-640S

<Making a call >

1.Pressing a button calls the specified master station.

2.Speak when a calling tone stops.

3.When a busy tone is heard, simply wait. You are put through the master station as soon as its line is freed.

4.If there is no response even after a calling tone has stopped, press the button again and again. The call- ing tone is sounded each time the button is pressed.

5.Conversation or continuous calling tone is terminated unless the button is pressed every 30 seconds.

Note.

1.Making a call from the door station to the master station having its Privacy switch in ON transmits a brief calling tone to the door station only twice, white transmitting a continuous calling tone to the master station.

2.The No.200 programming (Master/Sub relationship) must be performed in the exchange to call a specified master station.

9) Talk-back unit Model TK-20

< Making a call >

[When calling with the audio trigger function]

When the sound into the speaker exceeds the preset volume, the specified master station is called.

[When calling with the call switch]

1. Pressing the talk-back station call switch calls the specified master station.

2.Talk to the specified master station after a calling tone is terminated.

3.Simply wait after a busy tone (intermittent single tone) is heard.

As soon as the called station's line becomes free, your call is automatically connected.

Note. Be sure to set the audio trigger selector switch on the talk-back unit to ON.

<Response>

1.Talk to the specified master station after a calling tone is terminated.

Note. The No.200 programming (Master/Sub relationship) must be performed in the exchange to call a specified master station.

— 10 —

4. Station Operation (NP Type)

 

 

NP Type

1) Handset Master Station

Model

TL-600M/610M/620M

 

Handset

Speaker volume switch

Dial keys

In-use lamp

key

TL-600M

Handset

Retractile cord

Loudspeaker

In-use lamp

Keyboard

TL-610M

TL-620M

< Making a call >

1.Pick up the handset and dial the desired station number after hearing dial tone.

2.Start conversation after the calling tone stops.

3.When you hear a busy tone that indicates the party you call is on another line, you can camp on the line by simply waiting without hanging up the handset.

As soon as the line becomes free, your call is automatically connected.

4.While the continuous calling tone is sent, you can

break in on the calling tone by continuously depressing the key to make a voice call through the station speaker of the called party.

2) Handset Substation

Model TL-600S

Handset

5.Hang up the handset or depress the key to terminate the conversation.

<Responding to a call >

6.When you are called by the continuous calling tone or paged through your station speaker, respond to the call by picking up the handset.

Note.

The sound volume of the calling tone may be adjusted by means of a 2-stage volume selector (SP. VOL) switch.

NP Type

Speaker volume switch

In-use lamp

key

<Making a call >

1.Picking up the handset makes a call to the designated station.

2.Start conversation after the calling tone stops.

3.When you hear a busy tone that indicates the party you call is on another line, you can camp on the line by simply waiting without hanging up the handset.

As soon as the line becomes free, your call is automatically connected.

4.While the continuous calling tone is sent, you can

break in on the calling tone by continuously depress-

ing the key to make a voice call through the station speaker of the called party.

5. Hang up the handset to terminate the conversation.

<Responding to a call>

6.When you are called by the continuous calling tone or paged through your station speaker, respond to the call by picking up the handset.

Note.

The sound volume of the calling tone may be adjusted by means of a 2-stage volume selector (SP. VOL) switch.

— 11 —

3) Hands-free Master Station

Model HF-210M/210MB/670M/HS-670

 

NP Type

 

Speaker

In-use lamp

Privacy switch

Dial keys

Speaker volume switch

Microphone

HS-670

key

HF-670M

 

HF-210M

<Making a call >

1.Touch dial the station number you wish to call, regardless of whether the Privacy switch of your station is in the ON position or OFF position.

2.Start conversation after the calling tone stops.

3.When the line is busy, a busy tone is heard and you can camp on the line by simply waiting. As soon as the line becomes free, your call is automatically

connected.

4.During a call attempt made by means of the continu-

ous calling tone, you can break in on the calling tone

by continuously depressing the key to make a voice call through the station speaker of the called party.

5.When the party you call is in a high noise level area, your continuously depressing the key allows one-way conversation to that party. As long as you

depress the key, your voice has dominance and releasing the key will reverse the one-way conversation from that party to you.

<Responding to a call >

[Privacy switch is in the OFF.]

7.Respond to the call after the calling tone stops. [Privacy switch is in the ON.]

8.The continuous calling tone function is made avail- able to any station if its Privacy switch is placed in

the ON position. Depressing any key

other than the key causes the continu- ous calling tone to stop and puts the station in the conversation mode.

Note.

1.The sound volume of the speaker may be adjusted by means of the 2-stage volume selector (VOL) switch.

2.With no speaker built inside, the HF-670M needs to be connected to an external speaker. Also, the HF-670M is fitted with no Privacy switch.

3.When the HF-670M is connected to the handset unit HS-670, lifting up the handset responds to call.

6. To terminate the conversation, depress the key.

— 12 —

4) Hands-free Substation

NP Type

 

Speaker

 

In-use lamp

Privacy switch

 

Dial keys

Speaker volume switch

Microphone

 

 

key

HF-210M+YC-200

HF-210M+YC-240S

<Making a call >

1.Touching the key makes a call to the designated other station whether the Privacy switch on your station is in the ON position or OFF position.

2.Start conversation after the calling tone stops.

3.When the line is busy, a busy tone is heard and you can camp on the line by simply waiting. As soon as the line becomes free, your call is automatically connected.

4.During a call attempt made by means of the continu- ous calling tone, you can break in on the calling tone

by continuously depressing the key to make a voice call through the station speaker of the called party.

5.When the party you call is in a high noise level area,

your continuously depressing the key allows one-way conversation to that party. As long as you

depress the key, your voice has dominance and releasing the key will reverse the one-way conversation from that party to you.

6.To terminate the conversation, depress the key.

<Responding to a call >

[Privacy switch is in the OFF.]

7.Respond to the call after the calling tone stops.

[Privacy switch is in the ON.]

8.The continuous calling tone function is made avail-

able to any station when its Privacy switch is in the ON position. Depressing the or key causes the continuous calling tone to stop and puts the station in the conversation mode.

Note.

1.The sound volume of the speaker may be adjusted by means of the 2-stage volume selector (VOL) switch.

2.The No.200 programming (Master/Sub relationship) must be performed in the exchange to call a specified master station.

— 13 —

 

 

 

 

 

 

NP Type

5) Hands-free / Handset Master Station

Model HF-200M/200MB/250M (With Auto-Dialer)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Speaker

Handset

In-use lamp

Privacy switch

Speaker volume switch

Dial keys

HF-200M

Microphone

HF-250M

< Making a call >

1. Hands-free conversation may be made by simply touch dialing the station number you wish to call.

2.When you wish to use the handset, pick it up, then touch dial the station number you wish to call, or reverse the order.

3.Start conversation after the calling tone stops.

4.When you hear a busy tone that indicates the party you call is on another line, you can camp on the line by simply waiting. As soon as the line becomes free, your call is automatically connected.

5.In the event that the party you are calling does not respond and the continuous calling tone is still heard

from your station, you can break in on the calling

tone by continuously depressing the key to make a voice call through the station speaker of the called party.

6.During hands-free conversation, when the person you are talking to is in a high noise level area,

(1) Pick up the handset to talk or (2) depress the key continuously for one-way conversation

to that party. As long as the

key is depres-

sed, your voice has dominance, and releasing the key will reverse the one-way conversation from that party to you.

7.To terminate the conversation, hang up the handset or depress the key.

<Responding to a call >

[Privacy switch is in the OFF.]

8.Respond to call after the calling tone stops. [Privacy switch is in the ON.]

9.The continuous calling tone function is made avail-

able to any station when its Privacy switch is in the ON position. Depressing any key other than the key or picking up the handset of the station called causes the continuous calling tone to stop and puts the station in the conversation mode.

Note.

The sound volume of the loud speaker may be adjusted by means of the 2-stage volume selector (VOL) switch.

— 14 —

6) Hands-free / Handset substation

 

 

NP Type

 

 

 

Speaker

Handset

 

 

 

 

In-use lamp

 

Privacy switch

 

Speaker volume switch

Dial keys

Microphone

 

 

 

HF-200M+YC-200

 

 

HF-200M+YC-230S

<Making a call >

1.For hands-free conversation, touching the key makes a call to the designated other station regardless of whether the Privacy switch on your station is in the ON position or OFF position.

[Privacy switch is in the OFF.]

2. When you wish to use the handset, pick it up, then touch dial the key to make a call or reverse the order.

[Privacy switch is in the ON.]

3.Picking up the handset makes a call to the designated other station.

4.Start conversation after the calling tone stops.

5.When you hear a busy tone that indicates the party you call is on another line, you can camp on the line by simply waiting. As soon as the line becomes free, your call is automatically connected.

6.In the event that the party you are calling does not respond and the continuous calling tone is still heard

from your station, you can break in on the calling

tone by continuously depressing the key to make a voice call through the station speaker of the called party.

7.During hands-free conversation, when the person you are talking to is in a high noise level area,

(1) Pick up the handset to talk or (2) depress the

key continuously for one-way conversation to that party. As long as the key is depressed, your voice has dominance, and releasing the key will reverse the one-way conversation from that party to you.

8.To terminate the conversation, hang up the handset or depress the key.

<Responding to a call >

[Privacy switch is in the OFF.]

9.Respond to call after the calling tone stops. [Privacy switch is in the ON.]

10.The continuous calling tone function is made avail-

able to any station when its Privacy switch is in the

ON position. Depressing the key or picking up the handset of the station called causes the continuous calling tone to stop and puts the station in the conversation mode.

Note.

1.The sound volume of the loud speaker may be adjusted by means of the 2-stage volume selector (VOL) switch.

2.The No.200 programming (Master/Sub relationship) must be performed in the exchange to call a specified master station.

— 15 —

7) Hands-free/Handset Master Station with Auto-Dialer

 

 

 

NP Type

Model HF-250M

 

In-use lamp

Liquid crystal

 

Handset

display (LCD)

 

 

 

 

REGISTER switch Rear side

 

 

 

 

Station number card

 

 

 

Loud speaker

 

 

 

 

key

 

 

 

 

 

 

 

 

Auto-Dialer keys

 

 

 

 

Speaker volume switch

key

 

 

 

 

key

key

key

<Making a call >

1.Place the auto-dialer registration (REGISTER) switch in the OFF position.

2.16 registrations are possible with 8 keys by changing over the A/B page selection key.

You can call any one of pre-registered stations by touch-dialing the auto-dialer key.

3.For making a call and responding to a call without using the auto-dialer, refer to "5) Hands-free/Handset Master

Station HF-200M/200MB/250M (With Auto-Dialer)"

<Auto-dialer registration >

Two station numbers can be registered by each auto-dialer key.

Operation

1. Switch the (REGISTER) switch ON.

Indication on the liquid crystal display

 

or

 

 

2. Press the

key until

is

 

appeared on the LCD display.

 

 

Press it three times for

and

 

twice for

 

 

 

3. Press the auto-dialer key (

)to

 

select the station number to be registered.

 

 

 

 

Indication on the liquid crystal display.

4.Press the A/B page selector key to select either A or B page.

5.Station numbers can be consecutively registered by maximum 50 digits using the dial keys.

Indication on the liquid crystal display.

6.Press the key, and the dialled numbers are memorized.

7.Repeat steps (3) through (6) to register other station numbers.

8.Switch the (REGISTER) switch OFF after completing registration.

<Liquid crystal display >

A.Indication on the liquid crystal display in conjunction with the DT-E70 is changed with three status.

1.When waiting

Privacy mode status, page selection and time indication

Displays "PV"status when the privacy key is set to ON. Displays either A or B page of the autodialer.

2.When dialling for paging Dial monitor indication

3.When responding to a call

Calling station number

Waiting station number

Number of waiting stations

Note. For detailed indication mode, refer to "Calling Party Indication (Numerical Type)"

B.Indication on the liquid crystal display is changed into two status when the HF-250M is used solely.

His-own-station number

1.When waiting

Privacy mode status, page selection and his-own-station number

2.When dialling for paging Dial monitor indication

Note. For registration to use the liquid crystal display, refer to "Operating Instructions of the HF-250M and DT-E70".

— 16 —

8) Door Substation

Model HF-640S

NP Type

HF-640S

<Making a call >

1.Pressing a button calls the specified master station.

2.Speak when a calling tone stops.

3.When a busy tone is heard, simply wait. You are put through the master station as soon as its line is freed.

4.If there is no response even after a calling tone has stopped, press the button again and again. The calling

tone is sounded each time the button is pressed.

5.Conversation or continuous calling tone is terminated unless the button is pressed every 30 seconds.

Note.

1.Making a call from the door station to the master station having its Privacy switch in ON transmits a brief calling tone to the door station only twice, while transmitting a continuous calling tone to the master station.

2.The No.200 programming (Master/Sub relationship) must be performed in the exchange to call a specified master station.

9) Talk-back unit Model TK-20

< Making a call >

[When calling with the audio trigger function]

When the sound into the speaker exceeds the preset volume, the specified master station is called.

[When calling with the call switch]

1.Pressing the talk-back station call switch calls the specified master station.

2.Talk to the specified master station after a calling tone is terminated.

3.Simply wait after a busy tone (intermittent single tone) is heard.

As soon as the called station's line becomes free, your call is automatically connected.

Note. Be sure to set the audio trigger selector switch on the talk-back unit to ON.

<Responding to a call>

1.Talk to the specified master station after a calling tone is terminated.

Note. The No.200 programming (Master/Sub relationship) must be performed in the exchange to call a specified master station.

— 17 —

Functions: EXES-6000 CP-66

No. Classification

1

2

3

4

5Single Digit

6

7Continuous

Calling Tone

8

9

PTT

10

11Personal

12Number

13

14

15 Transfer

16

17

18

19 Priority

20

21 Conference

22

23Paging and

24Response

25

26

27

28

Selection of

Dial Operation

29

30

31

32

Restricted

Access Group

33

34

Selection

35

36

37

38

39

40

41 Interface

42

43

44

45

46

47

 

Standard

Selectable Function

Optional

Single

 

Tie-line

 

Function

By DIP

By No. 200

Own

Outside

TI-600

Function

Function

Exchange

 

Switch

Programming

Exchange

Exchange

Exchange

 

 

 

 

Camp-On-Busy

Busy call back

Mic-Off

Single Digit Dialing

Automatic Access to Paging

Master/Sub Relationship

Privacy-Camp-On-Privacy/Continuous Calling Tone at Privacy

Mode *1

Continuous Calling Tone-One-touch Response *2

Press-To-Talk

Press-To-Talk Control

Personal Number Call

Personal Number Paging

Remote Response

Call TransferPagind during Normal call

Group Hunting

Secretary Transfer

Call Forwarding

Priority

Executive Priority

Highest Executive Priority

Conference

PA Paging-Station Paging *7

Combination Paging

Emergency All-Call

Paging Priority

Selectable numbering digit

Selectable First Station Number of Each Exchange

Output Capacity of Paging Zone

Selectable Dial Operation for Paging Response

Output Capacity of General Purpose Control

Programmable Statio n Numbering

Selectable function operation

Group Blocking (Restricted Dialing)

Restricted Access to All-Call Paging

Zone paging

Restricted Access to Conference

One-shot make output

Restricted Access

Make/break output

to General Purpose

8

selectable one-shot make output

Control

8

selectable make output/Decimal output

4 decimal digits output

Calling Tone-paging Pre-paging Tone Duration *11

Time out of Conversation and Paging Call

IN/OUT Annuncation

Destination Annunciation Indication

Calling Party Indication (Lamp type) (with/without memory)

Calling Party Indication (Numerical type)

Station called indicator (Lamp Type)

Pager

One-shot make output

Make/break output

General Purpose

8 selectable one-shot make output

Control

8 selectable make output/Decimal output

4 decimal digits output

Speech message

Pager calling and responding

BGM

Alarm and time signal

Selectable paging

— 18 —

Functions: EXES-6000 CP-66

Notes.

1.XX/YY indicates to select either XX (Function) or YY (Function).

2.Not all circles in The Switch Selection table

correspond to the DIP switches of the CP unit.

*1: "PV" (system with Privacy function) Type: with the

Privacy switch in the ON position, a brief Privacy

Tone sounds.

"NP" (system without Privacy function) Type: A station may be called by the continuous calling tone when the Privacy switch is placed in the ON position.

*2: When a hands-free station without handset is called by the continuous calling tone, conversation may start by touching any key

*3: Using the Press-to-talk control function reduces the maximum number of paging zone to All call + 23 zones (7 zones).

*4: This function may not be used if numbers 100 through 199 are used in the Station Numbering

Schedule. Either "Personal number call" or "Personal number paging" may be selected.

*5: Additional equipment is required for paging.

*6: Either "Executive Priority" or "Highest Executive

Priority" may be selected.

*7: Each zone of paging provides Station paging and/or

PA paging.

*8: It is necessary to respond only by dialing (without zone No.).

*9: It is possible to make a paging call and its response between the local exchange and the remote extension exchange. However, a response to the zone paging is possible only from a station connected to the exchange having the paged zone.

*10: Station numbers of each exchange can be changed freely within the range of "Selectable numbering schedule of each exchange".

*11: Calling tone: 0.3 sec (Trill note tone)/0.2 sec (Single note tone)/none.

Paging pre-paging tone: 2 sec/1 sec/none.

*12: Selects whether or not the indication of the calling party station continuously lights up, after the calling party has cancelled the call to a line which is busy or in the privacy mode.

— 19 —

Chapter 2

Functions and operating procedures of single exchange system

EXES-6000 CP-66 — Summary of Dialing Operations (single exchange system)

1. Selecting dial operations

The EXES-6000 Intercom system allows digit-dialing operations to be minimized depending on the number of stations and their functions. Four types of dialing operations (Type 1, Type 2, Type 3, and Type 4) are available. Select the most suitable type by changing the setting of the internal switch at the exchange. The following explanations describe the dialing operation when the switch is set for Type 2. For other types, check the dial operation while referring to the attached lists.

[Four types of dialing operations]

Type

Feature

Numbering plan

 

Three-digit dialing

Standard type

 

Standard type

No. 200 ~ 327

Type1

Maximum of 128 stations

No. 100 ~ 227)

(without paging)

Station number conversion

 

 

Maximum of 120 stations

No.200~399

 

(with all station call + 7-zone paging)

(No. 100 ~ 399)

 

Three-digit dialing

Standard type

 

Station number conversion

No. 200 ~ 455

Type 2

Maximum of 256 stations

(No. 100 ~ 355)

 

 

 

Station number conversion

 

 

 

 

 

 

 

 

 

 

 

 

No. 200 ~ 999

 

 

 

 

 

 

 

 

(No.100~ 999)

 

Two-digit dialing

Standard/station number conversion

Type3

Full paging function

No. 20 ~ 79

Maximum of 70 stations

(No. 10 ~ 79)

 

 

(with/without paging)

 

 

Two-digit dialing

Standard/station conversion

Type 4

Maximum of 90 stations

No. 20 ~ 99

 

(with/without paging)

(No. 10 ~ 99)

— 20 —

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

(Type 1)

 

(Type 2)

 

(Type 3)

 

(Type 4)

 

 

Three-digit dialing,

Three-digit dialing, station number

Two-digit dialing,

Two-digit dialing, 60 stations

 

standard type, 128 stations

conversion, 256 stations

full paging function, 60 stations

(No. 20 through 99, No. 10 through 99)

 

(No. 200 through 327, No. 100 through 227)

(No. 200 through 999, No. 100 through 999)

(No. 20 through 79, No. 10 through 79)

 

 

Function

Dialing operation

 

Number assignment

Dialing operation

Number assignment

Dialing operation

 

Number assignment

Dialing operation

Number assignment

Press-to-talk

Remote response

Remote response registration

Continuous calling tone

Privacy

Secretary transfer

Single-digit registration

Single-digit dialing

Personal number cancellation

In/out indicator lamp ON

Personal number cancellation

In/out indicator lamp OFF

Personal number call

Personal number paging

Conference

Call forwarding registration

— 21 —

 

(Type 1)

 

(Type 2)

(Type 3)

 

(Type 4)

 

Three-digit dialing,

Three-digit dialing, station number

Two-digit dial,

 

 

Two-digit dialing, 60 stations

 

standard type, 128 stations

conversion, 256 stations (No. 200 through

full paging function, 60 stations

 

(No. 20 through 99, No. 10 through 99)

 

(No. 200 through 327, No. 100 through 227)

999, No. 100 through 999)

(No. 20 through 79, No. 10 through 79)

 

 

 

Function

Dialing operation

Number assignment

Dialing operation

Number assignment

Dialing operation

Number assignment

Dialing operation

Number assignment

Conference clear

Mic.off

Busy call back registration

Busy call-back response

Priority/priority response

Executive priority

Highest executive priority

Call transfer

All call + 7-zone paging

All call +

31 -zone paging

Cambination paging

All call paging response

Zone paging response

Paging transfer

22

Function

One-shot, relay-connection output

Relay connection/ disconnection output

8-selectable, one-shot,

relay connection output

8-selectable output (Decimal output)

4-digit decimal output

Pager call

Pager response

Calling station selection

Message recording

Message check

Message playback

Message cancellation

Remote message playback

Clearing calling party indication

BGM

 

 

(Type1)

(Type 2)

(Type 3)

 

(Type 4)

 

 

Three-digit dialing,

Three-digit dialing, station number

Two-digit dialing,

Two-digit dialing, 60 statins

 

 

standard type, 128 stations

conversion, 256 stations

full paging function, 60 stations

(No. 20 through 99, No. 10 through 99)

 

(No. 200 through 327, No. 100 through 227)

(No. 200 through 999, No. 100 through 999)

(No. 20 through 79, No. 10 through 79)

 

 

 

Dialing operation

Number assignment

Dialing operation

Number assignment

Dialing operation

Number assignment

Dialing operation

Number assignment

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

— 23 —

Camp-On-Busy

When the party you are calling is on another line, by simply waiting you automatically "Camp-On" the line. (Busy tone sounds continuously.) As soon as the line is freed, you will

be automatically connected.

After call

 

Call

Busy Call Back

When the called station is busy, dialing

permits this function to be registered and terminates the call after a confirmation tone. As soon as the line is freed, the calling party is called by the distinctive "busy-call-back" tone that sounds for 10 seconds. By one-touch dialing any one of key during the 10-second period, the calling party can be connected to the called party.

The disadvantage of the camp-on-busy function is that a link is occupied and busy tone is heard from your station all the way while you are waiting. This problem can be avoided by using the busy call back function that can improve the availability of speech paths as well as enables you to wait without being annoyed by "noisy" busy tone.

A maximum of 15 stations can be registered for this func- tion. Once the function has been programmed into your station, you are put in the simple "busy waiting" mode even when you depress 6 in an attempt to register other busy stations for this function.

It is possible to make or receive other calls while waiting after this fuction has been programmed. However, if you are still using your station for conversation with the third party when the busy station registered for this function is freed, the registered busy call back function will be cancelled.

Camp-on-busy is prior to busy call back.

Registration

Busy tone

Conversation

Calling station

Called station

Line has been freed.

Busy call back tone

Calling station

Calling

 

 

 

Called station

(Any key other than

— 24 —

Privacy

Shift Privacy Switch to ON.

When a party does not wish to accept incoming calls, this function may be employed to refuse them. With the Privacy switch in the ON position, a continuous privacy tone will be sounded in the station making the call, and at the same time, a brief Privacy tone will sound in the station called, indicating a call attempt is being made.

It is possible to call the other party from the station in the Privacy mode but Remote Response is impossible from that station.

Shift Privacy Switch back to the left.

To restore a station in the "Privacy" mode to a normal condition, and thus ready to receive calls.

Note: 1. A call received while the station is in the Privacy mode may be accepted if the Privacy function is immediately cancelled (see Camp-On Privacy)

2.In the even of the station registered for the Secretary Transfer function, the Privacy switch is used on and off operation of the Secretary Transfer function. (see Secretary Transfer)

3.During the above "Privacy" mode, while the call-

ing station has the bar is released, the privacy tone stops are the caller and transmit a

one way message.

When the bar is released, the normal "Privacy" mode to be resumed.

— 25 —

PV Type

One tone

Privacy tone

Call

Camp-On Privacy

When the party you are calling has his station on Privacy mode, by simply waiting you will automatically "Camp-

On" the line. (Privacy tone sounds continuously.) As soon as the Privacy mode is released, or as soon as he one-touch dials any of the keys , or as soon as he picks up a handset of his station, you will be automatically connected.

This function is canelled automatically if the station in the privacy mode may not accept the call within approximately

10 seconds.

PV Type

Automatic

Press-To-Talk

This function is activated when the

(Press-To-Talk Bar)

is continuously depressed after dial tone confirmation or during hands-free conversation. This allows one-way conversation from the party depressing the function key. When the key is released, one-way conversation is reversed.

Employ when a person in a high noise level area is called by a person in a quiet area, or when no particular response is required, or when simple announcements are made. In such cases, one-way conversation flow can be used.

One-way conversation is activated while the Press-To-Talk bar is continuously depressed.

As long as the Press-To-Talk bar is depressed by either party, the voice of the party using this function has dominance. When the key is released, the other party has dominance.

One-way conversation is reversed when the Press-To-Talk bar is released.

Mic Off

Touch dialing of

during a conversation turns off that station's microphone.

This function is used when for one reason or another it is desirable to stop a conversation temporarily. With this function in use, the conversation is interrupted. A party on hold can use the Press-To-Talk function even during the

Mic-off. Releasing the key cause the Mic-off to be resumed.

Touch dialing

again cancels the Mic-Off function, and the conversation

can be resumed.

__ __ _________

When it is desirable to resume the conversation interrupted with the Mic-Off function, the function may be cancelled by the Party who operates the Mic-Off.

If both parties depress the Press-To-Talk bar, the voice of the party who depresses the bar last will have dominance.

Depress the

to return to ordinary hands-free 2-way conversation ........

Note.

One-way conversation is impossible even if the

bar is depressed unless either party or both parties involved pick up a handset.

PV Type

Call

Again

Call

— 26 —

Mic Off

NP Type

Touch dialing of

during a conversation turns off that station's microphone, and a holding tone is heard at both stations involved.

This function is used when for one reason or another it is desirable to stop a conversation temporarily. With this function in use, a holding tone is transmitted to both the calling and the called station while the conversation is interrupted.

Touch dialing

again cancels the Mic-Off function, and the conversation can be resumed.

When it is desirable to resume the conversation interrupted with the Mic-Off function, the function may be cancelled by the Party who operates the Mic-Off.

Call

Holding tone

Holding tone

Again

Call

Press-To-Talk Control

Touch dialing the specific station number.

One way conversation is activated while the Press-To-Talk bar is continuously depressed, same as the Press-To-Talk (selected simplex) function, and a relay is activated with continuous make-contact.

One way conversation is reversed when the Press-To-Talk bar is released, and the relay is activated with break-contact.

Note.

1.Stations No.200 through No.207 (8 stations) are the specific stations.

2.It is possible to use a relay make output for Door Remote or for controlling Radio Transmitting/ Receiving Equipment through user provided interface.

3.The relay output of the Paging Interface Unit PI-62 is used for this purpose.

Adaption of this function permits the paging of only all-call plus 23 zones (the paging of all-call + 31 zones is impossible.)

Control

Relay of PI-62 unit

Specified station

(No.200~207)

— 27 —

Single Digit Dialing

Single digit registration

Register in advance as follows:

Confirmation tone

(Station number)

Station number

 

Confirmation tone

(Personal number)

Personal number

 

Confirmation tone

(Paging call)

Paging zone

 

Confirmation tone

(All-call paging response)

 

 

 

 

 

 

 

 

Confirmation tone (Each function)

Any six digits

Confirmation tone (Each function)

Any five digits

 

Confirmation tone

(Each function)

Any four digits

 

Confirmation tone

(Each function)

Any three digits

Confirmation tone (Each function)

Any two digits

< Single digit dialing >

When required, dial

and the registered number will be called automatically.

Note: 1. To cancel the registration, dial the station number of the station at which this functions has been registered.

2.It is also possible to use this function to shorten the long dial operation.

Example

Combination paging

Single digit

Simply dialing makes the combination paging instead of dialing

3. Single digit registration is not available from any substation programmed by No.200 programming, even if its line is connected with master station.

— 28 —

Master Sub Relationship

Master/Substation associations are set up by using station #200 as the programming station. Once these relationships have been established, substations can then contact their designated master stations by simply touch dialing

If TL-600S Handset substation is used, it can be connected to its designated master stations by simply picking up a handset.

With respect to this function, the stations in the system are divided into two categories; master stations and substations. Any master station can be connected to any other station in the system. However, substations can initiate calls only to specific master stations. This is done by single touch dialing, and will only connect the substation to one specific master.

Also, one master station can have 2 or more substations.

To register this function, dial

Confirmation tone

Substation No. paired off with the master

at the master station. This allows the master station to be connected to the substation when is pressed.

Note.

Once a certain station number has been designated as a substation by No.200 programming, the single digit dialing is impossible even when the master station is connected to that number.

Substation

Master Station

Handset substation

Single Digit Registration of Substation

Master Station

Substation Number

Substation

Automatic Access To Paging

This function requires "single digit dialing registration for handset station" as well as No.200 programming at time of installation.

A paging call can be placed over the specified zone by simply lifting the handset.

A paging response is possible by simply lifting the handset.

Paging call

Paging call

Paging response

Response to a paging call

Fig. 2

— 29 —

Personal Number Call

A personal number may be registered at any master station which the person to whom the number is assigned expects to be. A party wishing to receive personal number calls at a specific station may register his number at that station by touch dialing

Confirmation tone

Personal Number.

Those who are frequently away from their assigned station, as well as those who share a single station may be assigned a "Personal" 4-digit number which may be programmed to any master station in the system. This personal number, which is completely independent of station numbers, may be programmed at any master station, and any previous programming of that same number at any other station is automatically cancelled. When the party calling has dialed the number to which he wishes to speak, the call is then routed to the station at which the Personal Number was last registered. The numbers which may be assigned in this group are 1000 through 1999.

Personal number program cancellation can be done at any station be merely dialing:

Confirmation tone

Personal Number

When anyone having a personal number leaves the office, he merely cancels the programming of his personal number. With the personal number cancelled, any incoming calls to that number will be answered by a dial tone, indicating that he is not available.

Note.

The maximum number of the Personal Number remains same even if the number of exchange to be connected is increased to 2 or 3.

Registration

Personal Number

Personal Number Call

Personal Number

Call

Station where the personal number is registrated.

Cancellation (At any station)

— 30 —

Continuous Calling Tone

When there is an incoming call to the specified station, a calling tone is sounded continuously at the called station.

The continuous calling tone stops if the called party presses

1. Use this function when it is difficult to hear a brief single tone due to high background noise. Any station can be so made as to be called by the continuous calling tone, but No. 200 programming is required for such a station (refer to Installation Handbook for EXES-6000 CP-66).

2.If the calling party presses the key while the continuous calling tone is being sounded, the continuous

calling tone stops to allow the caller's voice call to go through. Releasing thekey restores the continuous calling tone.

3.If either party continuously presses the key during the normal two-way conversation, this makes a one-

way conversation from the party who pressed the key. Releasing the key reverses the one-way conversation flow and the other party has a dominance (Press-to-Talk).

Notes.

1. In the NP type system that has no Privacy function,

Continuous calling tone

Continuous calling call

Continuous calling tone

Call

Any key other than

the station can be called by the continuous calling tone if its Privacy switch is set to ON. This function by No. 200 programming is, therefore, used in the PV type system having the Privacy function or for the HF-670M industrial type station equipped with no Privacy switch.

2.The following stations can be called by the continuous calling tone:

(1)Stations in the "NP" type system or specified substations in the "PV" type system.

(2)Stations registered for continuous calling tone by No. 200 programming.

<Station vs. calling tone>

Type of station

(Specific station provided with Type of system "continuous calling tone" function by

station No.200 programming)

Non-programmed station (standard)

"PV" Type

Programmed station

Handset programmed station

Non -programmed station (standard)

"NP" Type

Programmed station

Responding to a call made by continuous calling tone

Type of calling tone

Privacy switch in OFF position

Privacy switch in ON position

Single "trill" calling tone

Privacy tone

(Call is put through immediately

 

after calling tone)

 

Continuous calling tone

Privacy tone

-

Continuous calling tone

Single "trill" calling tone

Continuous calling tone

(Call is put through immediately after

 

calling tone)

 

Continuous calling tone

Continuous calling tone

Depress any dial key other than

1 . Depress only dial key other than

key.

key.

 

2. Pick up a handset.

 

3. Shift Privacy switch to OFF.

— 31 —

Remote Response

A call to a certain station can be remotely responded to from the other station by simply depressing while a continuous call tone is ringing or within 5 seconds after a brief call tone has stopped ringing.

Notes.

1.The Remote Response is only possible among stations programmed for this function.

2.When making the remote response from the station having its Privacy switch in ON position, shift the

switch back to OFF or lift its handset before depress- ing

Programming the remote response group

Establish the remote response group of stations and designate a specific station within the group as a temporary "Master station" and the rest as "Substations".

Set up the "Master station" by dialing.

Confirmation tone

Station No. to become "Master station".

Register the "Master station" No. at the "Substation" by dialing

Confirmationtone

Master's number

Note.

Be sure to register the station No. that becomes the "Master station" at the "Master stations".

Cancelling remote response programming

Touch dialing at each "Substation"

Confirmation tone

His own Substation number cancels the Remote response program.

Dial operation for Remote response

Calling tone

Calling

Station

No.201

No.209

No.203

Remote response group

Conversation after Remote response

Conversation

Station

No.201

No.209

No.203

Remote response group

Programming the remote response group (Example)

Station

No. 201

Station

Station

Station

No. 204

No. 203

No. 202

Remote response group

— 32 —

Call Transfer

Call Transfer from Called Station

During the conversation, first dial

(the Station Number of the person the call is to be transferred to).

The original call is then held and the holding tone is transmitted to the other party, while the third party is called and asked whether he will accept the call. If he agrees to accept the call, dial or hang up a handset,

and the transfer will be completed.

This function allows called party to transfer that call to another station. The party to whom the call is to be trans- ferred, may be called using either the Station Number, the

Personal Number or through Single Digit Dialing.

Call Hold and Call Back from Calling or Called Station

During the conversation, first dial

(Station No. of the third party.)

The other party is then placed on hold while the third party is called. Upon completion of the conversation with the third party,

dial

or the third party dials

or replaces his station handset.

This allows the original conversation to resume.

The Transfer function is combined with the Call Holding function.

When two parties are talking, either one can be temporarily placed on hold to permit the call to another station. When the conversation with the third aprty is over, the original conversation can be resumed.

The third party can be called using either the Station Number, his Personal Number or through Single Digit Dialing.

Called Station

Third Party

Call Back

Call

Called Station

Calling Station

Called Station

Transfered Station Number

Called Station

Calling Station

Holding

Call

Third Party

Transfer

Called Station

Called Station

Calling Station

Call

Third Party

Called Station

Calling Station

Original Call

 

Third Party

— 33 —

Paging during Normal Calls

This function allows a paging call to be made during the conversation to call the third party and ask him if he accepts the call, while holding the original conversation. The original call, if he accepts, is transferred to the third party.

When it is desirable to call the third party during the conversation, press plus the desired paging zone.

(0~7, 00~31, *00~15). This place the conversation on hold and allows a paging call to be made.

Wait for a paging response by pressing . (The original conversation is restored.) When there is the paging response, the conversation is interrupted and the paging party is automatically connected to the third party, while transmitting a holding tone to the conversation partner.

Dial again when coming back to the original conversation. To transfer the original call to the third party, press or replace the handset.

* When the exchange in use is EX-610 or EX-620.

Note.

This function can be operated when both "Call Transfer" and "Paging" functions are employed.

Group Hunting

When the called is busy, the call is automatically rerouted to the pre-programed.

When that station is also busy, the call is further rerouted to the other pre-programed station.

Notes.

1.To use this function, No.200 programing must be established for station a call is to be rerouted to. Also set the DIP switch for Group Hunting to ON.

2.If all stations are registered for this function by

No.200 programing so that an imcoming call may make a loop in the group, any incoming call is automatically transferred to an idle station.

Conversation

Calling party

Called party

On hold

Station paging

 

External PA paging

Resuming

the original call

— 34 —

Secretary Transfer

This function is only available when a specified station is programmed for this purpose with use of Station #200 in the programming mode. Automatic transfer of incoming calls by an executive to his secretary is accomplished by placing the Privacy Switch on his station in the ON position.

This function allows a secretary to accept all incoming calls placed to an executive.

For the executive to accept calls directed to his station once the automatic secretary function has been programmed by station #200, he simply moves the privacy switch to the left, or OFF position.

It is also possible for the executive to accept calls at his station.

There is no limit to the number of Executive/Secretary pairings except by the number of available number combinations within a given system.

When a secretary who is already programmed for this function wishes another secretary to accept all incoming calls directed to an executive, station No. 200 programming of another secretary should be set up in the exchange. Then, the calls can be rerouted to another secretary if the executive and the secretary first registered place their Privacy switches in the ON position. It is also possible to transfer the call in a daisy chain method.

Note.

When 2 or 3 exchanges are connected by tie-line, set up a Secretary/Executive association within a group of stations connected to the same exchange.

Executive

Secretary

Digit the executive station.

— 35 —

Secretary Transfer and Call Transfer

Combination of the secretary transfer and call transfer allows rerouting of the call transferred to the secretary back to the executive's station.

When the secretary answering a call touch dials

Executive's station number

the privacy tone sounds continuously at both stations, while the call is held. The holding tone is transmitted to the calling station. If the executive shifts the privacy switch to the left position, or if he depresses any of the keys other than the key( ), or picks up a handset he can talk with the secretary. If the call held is to then be transferred back to the executive's station, the secretary is to touch dial , or to hang up a handset, and the original calling station will be connected to the executive's station.

Secretary Transfer and Call Transfer using Single Digit Dialing

Combination of "Secretary Transfer", "Call Transfer" and "Single Digit Dialing" allows simple retransfer of the call transferred to the secretary back to the executive's station.

Touch dial

Confirmation tone

Executive's station number

at the secretary's station in advance. When the call transferred to the secretary has to be transferred back to the executive, the secretary simply touch dials

at her station. This sends the continuous Privacy tone to both stations while the call is held. If the call is to be transferred back to the executive's station, the secretary touch dials or hangs up a handset.

The calling station will then be connected to the executive's station.

If there is no answer from the executive, the secretary touch dials

and the original call is resumed.

Unless the executive sets his station Privacy switch to OFF within 10 seconds after the Privacy tone has sounded, the call attempt to the executive is cancelled for automatic return to the original conversation.

 

PV Type

 

Executive

Secretary

Other person

 

Call

Secretary dials

(Executive)

Privacy tone

 

Executive

Privacy Tone

Holding tone

Holding

Secretary

Other person

Executive

or depresses any of the keys

or picks up a handset

Executive

Holding tone

Call

Secretary

Other person

Call Transfer

 

Call Back

 

Secretary dials

Secretary dials

or hangs up a handset

 

 

Executive

Executive

Call Transfer

 

 

Secretary

Other person

Secretary

Other person

— 36 —

Secretary Transfer and Call Transfer

Adoption of the selective function "Transfer" allows rerout- ing of the call transferred to the secretary back to the executive's station.

When the secretary answering a call touch dials

Executive's station number

the continuous calling tone sounds at both stations, while

the call

is held. The call holding tone is transmitted to the

calling

station.

If the executive shifts the

privacy switch

to the

left position, or if he depresses any of the keys

other than the

key (

), or picks

up a handset he can talk with the secretary. If the call

held is to then be transferred back

to the executive's

station, the secretary is to touch dial

, or to hang up a

handset, and the original calling station will be connected to the executive's station.

Secretary Transfer and Call Transfer using Single Digit Dialing

Adoption of the selective functions "Transfer" and "Single Digit Dialing" allows simple retransfer of the call transferred to the secretary back to the executive's station.

Touch dial

Confirmation tone

Executive's station number

at the secretary's station in advance. When the call transferred to the secretary has to be transferred back to the executive, the secretary simply touch dials

at her station. This sends the continuous calling tone to both stations, while the call is held. If the call is to be transferred back to the executive's station, the secretary touch dials or hangs up a handset.

The calling station will then be connected to the executive's station.

If there is no answer from the executive, the secretary touch dials

and the original call is resumed.

 

NP Type

 

Executive

Secretary

Other person

 

Call

Secretary dials

(Executive)

Continuous calling tone

 

Continuous Executive

calling tone

Holding tone

Holding

Secretary

Other person

Executive

or depresses any of the keys

or picks up a handset

Executive

Holding tone

Call

Secretary

Other person

• Call Transfer

 

• Call Back

 

Secretary dials

Secretary dials

or hangs up a handset

 

 

Executive

Executive

Call Transfer

 

 

Secretary

Other person

Secretary

Other person

— 37 —

Call Forwarding

When you will be away from your station and wish all incoming calls to be rerouted to a different destination you are going to move to, you can do so by registering that station number before you leave.

Registering Call Forwarding function

To program this function, touch dial plus the station number of the destination you are going to move to (confirmation tone is heard). This function may only be registered at the originally assigned station and any previous programming made for this function is automatically cancelled each time the new destination is registered.

Registration of Call Forwarding

Call

Destination Station No.

Station

No.202

Cancelling Call Forwarding function

Touch dial

Original assigned station No.

Notes.

1. Call made in the following instances are directly put through to the original station, independently whether or not this even if call forwarding function has been programmed.

1.Calls from the registered destination station to the original station.

2.Calls by a personal number.

2.Before a call is automatically rerouted to the registered station, a brief confirmation tone sounds at the original station, indicating that the incoming call is put through to the registered station.

3.This function is available only between stations within the same group when the system employs Group Blocking function. Even when it is possible to

make a call between stations of

different groups,

Call Forwarding function cannot

be registered be-

tween them.

 

Station

No.201

No.203

Cancellation of Call Forwarding

Original Station No.

Station

No.201

Station

No.201

No.203

— 38 —

Priority

When the party called is on the line, as indicated by the busy tone, dialing

transmits a priority tone to the called party. The same tone is audible at the calling station. The call is connected if the called party also responds by dialing

In this event, the original conversation partner of the party called is temporarily placed on hold and the holding tone is transmitted to his station.

Upon completion of the priority conversation, the party who placed the priority conversation dials

or replaces the handset.

This allows the interrupted conversation to resume.

When the called party is already on the line, the party calling, if he deems it necessary, can send a Priority signal to the called party. After a response from the party called, the urgent call is allowed to take priority and go through.

Busy Tone

Priority

Original Call

Priority

Priority Call

Holding Tone

Response

Executive Priority

 

 

This function is available only for those stations specifically

 

programmed for this function, with programmed station

 

#200. When the station called is busy or in the Privacy

 

mode, as indicated by the busy or privacy tone, dialing

 

sends a priority tone. This priority tone is transmitted for a

 

few seconds and then the call is put through.

Original Call

 

 

In this event, the original conversation partner of the party

 

called is put on hold and a holding tone is transmitted to

Busy Tone

his station.

 

 

Upon completion of the priority conversation, the party

 

placing the priority call dials

or replaces the

 

handset.

 

 

The original conversation can be resumed.

When the called station is busy or in the "Privacy" mode, this function allows forced interruption for priority conversation.

Priority Call

Holding Tone

Priority

— 39 —

Highest Executive Priority

This function is available only for those stations specifically programmed for this function, with programming station No. 200. When the station called is busy, as indicated by the busy or privacy tone, dialing

sends a priority tone. This priority tone is transmitted for a few seconds and then the call is put through, terminating the original conversation.

When the called station is busy or in the Conference mode or during a paging call, this function allows forced interruption for priority conversation.

Note.

Either Executive Priority function or Highest Executive Priority function may be employed.

*When the party called through the conference function is busy and it is desirable to interrupt his conversation, dial

Priority

Original Conversation

Busy Tone

Priority Call

Conversation Over

— 40 —

Conference

A "Hands-Free" conference call can be made with up to 4 persons. For a conference under this function the other participants may be called either through their station num- ber, personal number or by Single Digit Dialing. Addition of stations or personal numbers (total of only 4) may be added by anyone already connected.

The person who proposes the conference may dial

(Station Number of the 1st of the participants)

After receiving 2nd person's consent, he may then dial

(2nd participant)

After receiving 3rd person's consent, he may now dial

(the last participant)

At this point, the 4-man conference may begin. It is also possible for any of the 4 participants to call up any of the other participants.

Both the 2nd and the 3rd persons can be called up in one dial operation without obtaining their consents.

A person wishing to drop out of the conference should dial

or hangs up a handset

at his station.

Any of the participants who wish to drop out during the conference may do so as long as it's not the party who originated the conference.

The function is cancelled and the normal mode is restored when the person who arranged the conference dials

In the event that the calls made by the person arranging the conference are not answered or that there has been a dialing error, the function can be cancelled for restoration to the normal mode.

The conference is terminated when the party who arranged the conference dials

or hangs up a handset

When the conference has been terminated by the party who originated it, the other participants cannot continue the conference.

Either of the parties in conversation is to dial

(the Station Number of the third party).

It is possible for persons in normal conversation to change to the Conference mode without interruption.

A "Hands-Free" conference call can be made with up to 4 persons.

Dialing of conference member.

Station number

Personal number

Single Digit

— 41 —

Paging

A variety of paging modes allows paging over a wide area from any master station. The paged party may respond from the nearest master station.

Paging modes include external PA systems and/or Station paging and Zone paging is for calling a limited area, and All-call paging is for calling over the entire area.

Response to a paging call may be made by means of Auto- matic response or Zone number dialing.

1. External PA paging and Station paging

A.External PA paging

1.Paging through external speakers is possible from any master station, with the paged party able to respond from the nearest master station.

2.External PA paging zones and all-call paging are

possible up to a maximum number of 31 zones.

B.Station paging

1.Paging from any master station to all stations within a certain area is possible through the station speakers. But the page will not be heard at stations in use in the area.

2.Station zone paging and all-call paging are possible only within zone 1 through 31.

2.Zone paging and All-call paging

A.Zone paging (Individual zone paging).

Paging and Paging response are possible through Zone

paging. To page a specific zone, press and the zone number. To respond to a zone page, press simply or plus the zone number.

Paging to zones 1 through 31 may be made through external PA paging using the external amplifiers and speakers, and/or through station paging using the station speakers.

B.All-call paging

Paging and Paging response for External PA and/or

station paging is possible through All-call paging. To

make an all-call page, press (maximum of 7

zones) or (maximum of 31 zones). To respond, press or

This does not necessarily mean that All-call station paging must reach all the stations.

C.Maximum paging zones

Exchange

Station paging

Public address paging

EX-610/620

All call +7 zones

All call +15 zones

EX -630

All call +31 zones

All call +31 zones

3.Responding to a paging call A. Automatic response

1. Zone paging response

 

Touch dialing

at the station within the paged

zone permits a response to the party who placed a paging call.

In this event, No.200 registration of the stations

(consecutive station numbers) within each zone must be made.

2.All-call paging response

Touch dial at any station and the paged party is put through to the party calling.

B.Zone number dialing

1. Zone paging response

The paged party is connected to the party calling by depressing.

 

(Zone number)

 

at any station.

 

 

2. All-call paging response

 

Depressing

or

permits a re-

sponse to the party calling.

— 42 —

Other Paging Modes

1.Combination paging

Combination paging is used when several zones must be paged simultaneously through External PA or Station paging. A special paging area can be created wherever the paging ranges overlap by combining several zones. A maximum of 20 combinations can be created in this way from a maximum of 31 individual zones.

2. Emergency all-call paging

Emergency external PA or station all-call paging can be made either from the specified station (No.247) or by an external input signal connected to line No.247. All normal calls and pages are interrupted for the duration of the emergency All-call page, returning to normal when the page is terminated.

3. Paging priority

Note.

Dial operation of Combination paging Paging call

Combination zone No. (80 ~ 99)

Paging response

Combination zone No. (80 ~ 99)

In normal station paging, the page is not heard at any station already in use. By using the paging priority function, the call can be interrupted to allow the page to go through. A holding tone sounds at the other party's station, and the call is restored when the page is terminated.

All-Call paging

Combination zone No.81

Combination paging

Combination zone No.80

 

 

Individual zone No. 1

< Example >

 

 

 

Individual zone No. 2

 

 

Individual zone paging

 

 

 

 

Individual zone No. 3

 

 

 

 

 

 

Individual zone No. 4

 

 

 

 

 

 

 

 

 

 

 

 

Note: Priority of Paging

Emergency all-call paging > All-call paging > Combination paging = (Individual) zone paging

1.The higher priority page overrides the lower priority one. The lower priority page will be restored when the higher priority page is terminated.

2.Individual zone pages made while a Combina-

tion paging is in progress will result in Camp- On-Busy.

— 43 —

How to select the paging area and make the paging call.

Paging functions may include both external PA and stations, depending on the zone being used. The paging area is limited to individual zone, Combination paging and All-call paging depending on the call range.

Dialing operation

Paging call

Paging area

 

All-call and

All-call and

No. maximum of 9-

maximum of

zone paging.

15-zone paging.

All-call paging

Zone paging up to 31 sones

Maximum of 15 zones

Combination paging of up to 20 zones

*When EX-610 or 620 is used.

All-call

Zone 1

Zone7

Zone 8

Zone 31

Combination

zone 90

Combination

zone 99

Response

Automatic

Zone number

response

dialing

External PA paging

Station paging

Zone 1 through 7

Zone8 through 31

< Example >

— 44 —

All-Call Paging and Individual Zone Paging

Paging call

External PA paging to a specific zone is possible from any master station by pressing

or

('0' or '00" = all-call)

and the desired zone number ('0' = all-call). It is possible to wait for a response in this mode, but anything said will be broadcasted over the entire zone. It is best to end the paging call by pressing

or hanging up a handset

and waiting for a response.

* When EX-610 or 620 is used.

Paging to zones 1 through 31 may be made through external PA paging using the external amplifiers and speakers, and/or through station paging using the station speakers. When EX610 or 620 is used, the maximum number of stations for public address paging and station paging are 15 zones and 7 zones respectively.

All zones are paged at the same time by all-call paging.

Paging response

1.Automatic response

To respond to a paging call, go to the nearest master station and press either

(All-call paging response) or

(Zone paging response).

2.Zone number dialing

To respond to a All-call paging, go to the nearest master station and press

To respond to a Zone paging call, press

Zone No. 1 ~ 9 (01 ~ 31)

at the nearest station.

Note 1: When all-call paging is initiated during zone paging, the Zone paging is interrupted and restored after the all-call paging is finished.

Note 2: To respond to Zone paging by pressing No.200 registration of the stations (consecutive station numbers) within each zone must be made. Such registration is required for both external and station paging. For further details, please refer to Installation Hand Book for EXES-6000 CP unit.

All-call paging

Zone paging

Response to zone paging

Response to All-call paging

Table of stations used for individual zone paging. (Example)

— 45 —

Combination Paging

Several zones can be called simultaneously using external PA paging and station paging. This is combination paging and is initiated by pressing

Paging will be broadcast to predetermined zones. It is possible to wait for a response in this mode, but it is usually preferable to terminate the paging call and wait for a response. The paged party can respond by pressing

80 ~ 99 at the nearest station. Refer to Example 1.

Priority of paging

All call paging>combination paging= individual zone paging

1.When some stations are already receiving another combination paging, the second paging call will be put on camp-on-busy. Refer to Example 2.

2.When some stations are receiving individual zone paging, a combination paging call will be put on camp-on-busy.

Likewise, when a combination paging call is being received, individual zone paging calls will be put on camp-on-busy. Refer to Example 3.

Responding to combination paging and zone paging

1. Automatic response

To respond to zone paging or combination paging, press

When the same zone is called via both zone paging and combination paging, responses will be put through to the station calling last. Refer to Example 4.

2. Zone number dialing

To respond to the (individual) zone paging call, depress

1~7

(01~31)(*01~15)

Depressing

(80~99)

permits the response to the combination paging call.

* When EX-610 or 620 is used.

< Example 1 > Combination of individual zones

Combination zone 91

Combination zone 92

Combination paging to

Combination paging to

combination zone 91

combination zone 92

< Example 2 >

 

Combination zone 93

Combination zone 94

Call

Camp-on-busy

 

Combination paging to

Initiating combination paging

combination zone 93

to combination zone 94

< Example 3 >

Combination zone 94

Camp-on-busy

During paging to zone 2

Initiating combination paging

to combination zone 94

 

— 46 —

< Example 4 >

To use the combination paging, Programing must be established for each individual paging zone included in each combined zone.

For further details, refer to Installation Hand Book for EXES-6000 CP unit.

Programming for Example 1.

Combination

 

Individual

zone

Dialing

zone

— 47 —

Emergency All-Call Paging

Handset substation TL-600S should normally be used for

< Emergency all-call paging is made >

the emergency all-call station, No. 247.

 

To broadcast emergency all-call paging, pick up a handset.

All-call

The highest priority all-call paging can be broadcasted to all zones without a paging pre-announcement tone. During emergency all-call paging, all other paging calls and normal calls are interrupted until the handset is replaced to finish the emergency message.

< Emergency all-call paging is finished >

1.This function may be used to announce emergency instructions from the specified station No.247. It may also be used to provide the signal tones such as chime or alarm signals when the signal sources are fed to No.247 circuit.

2.To make emergency all-call paging from the specified station No.247 using Hands-free type of station, move the privacy switch from "ON" to "OFF" position.

— 48 —

Priority Station Paging

Normal station paging calls are not audible at the busy stations, but the Priority Station Paging can break in on such busy stations.

1. Dial

(zones: 1 ~ 7, all-call: 0),

(zones: 01 ~ 31, all-call: 00), or

(*01~15)

(combination zones: 80 ~ 99).

If there is a busy station, the conversation is interrupted and the paging call is allowed to go through, while transmitting a holding tone to the conversation partner placed on hold.

2.The converstion is restored when the paging is finished.

(*)

3.To respond to the paging call during the conversation,

first terminate it by depressing or by replacing a

station handset and then dial

or

(Zone

No.) (Zone paging or combination paging response) or or (All-call response).

*When the EX-610 or EX-610 is used.

*The conversation is not restored if the Privacy switch is set to ON. (In the EX-6000 system, it is possible to page or respond to a paging call even when the Privacy switch is ON.)

Notes.

(1)Dialling keys while receiving a station paging call makes the call inaudible at that station and connects that station to the called station.

(2)When the called station is being paged, a busy tone is transmitted to a calling party and he can "campon". Refer to Example 2.

(3)When a paged zone (Zone 1) has a station placing a paging call over the other zone (Zone 2), a party who has paged the zone 1 is put in the "Camp-on- busy" mode. Refer to Example 3.

(4)For the Priority Station Paging function, stations (consetive numbers) in each paging zone, which can be interrupted during conversation, must be programmed at the station No.200. This is also required to programme the zones for automatic paging response (see Note 2 of Paging) and station groups having acess to incoming telephone calls.

(5)Even when the Priority Station Paging function has been adopted, by establishing the station No.200 programming (Function Code 39) desired stations can be made to refuse a priority paging call when

they are busy.

(6)When the system incorporates Station paging and

PA paging at the same time, employ the Zone

number dialing method

for the

paging response. Also, set up "Station No.200 programming" for Priority Station paging. If the

Automatic reeponsing method is employed, then "No.200 programming" need to be set up for every station and conversation is interrupted each time the external PA paging is made.

< Example 1 >

< Example 2 >

< Example 3 >

Programming for Example 1, 2 and 3

— 49 —

Personal Number Paging

If you wish to receive personal number paging call, register your personal number at any station in the desired paging zone by dialing

Personal number

A calling party can page you automatically in that zone if he dials.

Personal number

To respond to a paging call, press on the nearest master station.

This function allows those who are frequently away from their original station to be paged automatically in the area where they are available, if personal number registration is done.

When you move from that registered area to another, make the same programming again.

When you leave the office, cancel the personal number registration, which may be done from any station by dialing

confirmation tone is heard.

Personal number

With your personal number cancelled, any incoming call to your number will be answered by a dial tone, indicating that you are not available.

Note.

1.There is no limit to the number of personal numbers that may be registered at any single station, but the personal numbers which are used in this function are

No.1000 through 1999.

2.Either the personal number call function or the

personal number paging function is selectable.

3.No.200 programming must be established for stations of each paging zone.

4.In the systems where the zone number must be pressed to respond to a paging call, dial for paging response.

Registering a Personal Number

I Any station in a Paging zone No. 3

(Example)

Personal Number

Calling from any master station

Personal Number

Paging response

Paging to the zone in which a person is registered

Any station in a paging zone No. 3 (Example)

Responding to Zone paging

Cancelling Personal number

Cancellation is possible at any station

— 50 —

Selectable First Station Number

The first station number of the system may be selected from any of the following numbers (Hardwired station number): 100/200/300/400/500/600/700/ 800/900.

The system with Personal Numbers can't use No. 100 ~ 199.

Note.

Station No. 200 programming is required when any other numbering schedules than standard (No. 200 ~) are used.

Programmable Station Numbering

This function allows the system to have "Programmable station numbers'', other than the "Hardwired station numbers" by programming.

The unprogrammed stations are used as original hardwired station numbers.

Type of dial operation

Hardwired

Programmable

station number

station number

 

With Personal number

No.200 ~ 455

No.200 ~ 999

Without Personal number

No.100 ~ 355

No.100 ~ 999

1. Numbering schedules can be changed easily by programming in stead of rewiring.

2. Such numbering schedules as 200's, 300's and 900's can be grouped together for each individual office.

3.Hardwired stations of each paging zone must have consecutive numbers. To make the programmable station numbers inconsecutive, use this function.

4.This function requires No.200 programming. See Installation Instructions for EXES-6000 CP unit.

Dialing

Exchange

Programmable station

 

No. 203

 

 

 

 

Circuit No. 201

 

 

(Hardwired station

 

 

number)

 

 

Circuit No. 203

 

 

(Hardwired station

 

 

number)

 

 

Programmable station

 

 

No. 201

5.People operating the intercom stations need not worry about the Hardwired station numbers. Note, however, that the hardwired station numbers are used to program all the setup data of each function into the exchange through No.200 programming.

< Example >

Hardwired

Programmable

station number

station number

Department 1

Department 2

Hardwired Programmable station number station number

Station

paging zone

Hardwired Programmable station number station number

—51—

Group Blocking

Function (A) . . The system can

be grouped or divided

into a maximum

of 8 groups of stations

with sequential station numbers. Stations in the group cannot call another.

Function (B) . . The group can call and/or be called by any other group (s) by programming.

Function (C) . . The paging zone number (all-call, individual zone and combination) which each group can call is programmable. (No distinction is made between external and station paging.)

Note.

1.When the paging call is made, the group of stations to which the response is made is restricted by Function

B. Function B permits the normal station call in the direction of the arrows. Its paging response can be made in the opposite direction of the arrows.

(Refer to Fig. 4)

< Example of Paging response >

When the programming is set up for the normal station call as is shown in Fig. 2, the paging response is only possible in the direction of the arrows of Fig. 4.

Note.

2.To use this function station No.200 programming for the allocated station number, group, paging zone, etc., must be set up in the exchange. For further details, refer to Installation Hand Book for EXES6000 CP unit.

<Programming for Fig. 1, 2, 3 and 4 >

Group 1 No.201 ~ 209

Group 2

Group 3

Group 4

No.210~219

No.220~249

No.250~279

 

Fig. 1

 

 

Group 1

 

Group 2

Group 3

Group 4

 

Fig.2

 

 

 

 

 

Group 1

 

Group 2

Group 3

Group 4

 

Fig. 3

 

 

 

Paging station

 

Group 1

 

Group 2

Group 3

Group 4

 

Fig.4

 

< Example >

Calling station

Station receiving

All-call paging

Zone 4 paging

Paging zone

Paging station

Paging response

Station responding to paging call

Function registration (A)

Function registration (B)

 

Station for

Group No. of calling

Group No. of station

 

station

 

receiving call

 

each group

 

All-call

Station not in group

Stations capable of being called without registration. Stations not belonging to the group.

Function registration (C)

Paging zone of station receiving call

Zone No.

Combination zone No.

< Example >

—52—

Programmable Restricted Access for Stations

Stations at which the following 7 specified functions can be restricted.

1.All-call paging

2.Zone paging.

3.Conference

Station number

4.General purpose control

Mode 1 (One-shot make output)

5.General purpose control

Mode 2 (Make/break output)

6. General purpose control

Mode 3 (8 selectable one-shot make output)

Unit No. Condition No.

General purpose control

Mode 4 (8 selectable output or decimal output)

Unit No. Condition No.

7. General purpose control

Mode 5 (4 decimal digits output)

 

(Unit No.)

(4-digits)

 

1. For conference, only the specified stations (one or more) can make a call, but any station can be called.

2.No.200 programming must be established for the specified stations.

—53—

Selectable Calling Tone

The duration of the calling tone can be set for either 0.2 second (single note tone) or 0.3 second (warble tone). It is also possible to have the station without any calling tone.

Note.

1.The duration of the continuous calling tone is impossible to change.

2. It is impossible to use different calling tone modes in one same system.

Selectable Paging Pre-paging Tone Duration

Paging pre-paging tone can be chosen from "2 seconds",

"1 second" and nothing.

Time-Out of Conversation

It is possible to limit the conversation duration to one through ninty-nine minutes in the unit of one minute in order to improve speech path availability. A hurry-up tone is sounded in both the calling and called stations approximately 10 seconds before the busy stations are automatically disconnected from the speech path.

Time-Out of Paging Call

This function is employed to prevent the unnecessary line occupation as a result of a paging party's failure to depress the key after a paging call establishment. The paging call is automatically cancelled after a certain period of time, which may be set at one through nintynine minutes in the unit of one minute, with a hurry-up tone transmitted to the paging station approximately 10 seconds prior to the automatic disconnection. When the paged party responds, the conversation is automatically cut off after the duration set by the Time-out of conversation function.

—54—

In/Out Annunciation

The in/out annunciation indicators can be turned on or off from any master station by using the personal number registering procedure.

When a personal number registration is made at a station, by dialing

Confirmation tone

1000~1999 (personal number)

the personal number is registered at that station and the personal number lamp on the in/out indication panel is turned on.

Personal number call

By dialing

1000~1999 (personal number)

from any station, the call is put through to the station registered with the personal number.

Cancelling personal number and turning off in/outannunciation.

By dialing

Confirmation tone

1000~1999 (personal number) from any station, the personal number is cancelled and

the personal number lamp on the in/out indication panel is turned off.

1.The maximum number of in/out annunciation windows is 1000.

This maximum number remains the same even when the number of exchanges to be connected is increased to 2 or 3.

2.The in/out indication panel must be used with the Data

Transmitting and Receiving Units (DT-E60 and DR-B61).

In/out indication panel

. . .

Lamp on

Personal number

In/out indication panel

Lamp off

Personal number

—55—

Destination Annunciation Indication

When a personal number is registered at the station of the destination a person has moved to, the corresponding lamp on the destination indication panel comes on, indicating where he is.

Dial

Confirmation tone

1000 ~ 1031 (personal No.)

at any station (No.201~No.232), and the personal number is registered at that station and the corresponding station number is indicated by lamp. The personal number from 1032 to 1999 can be registered at the station but the corresponding station lamp does not come on. Registering the same personal number at another station causes the original station's lamp to extinguish and the new station's lamp to come on.

Personal number call

By dialing

1000 ~ 1999 (personal No.)

from any station, the call is put through to the station registered with the personal number.

Cancelling Personal number registration and turning off Destination indication

By dialing

Confirmation tone

1000 ~ 1031 (personal No.)

from any station, the personal number program is cancelled and the registered station's lamp on the destination indication panel goes out.

Note.

1.The personal numbers which may be assigned to this function are from No. 1000 to 1031.

2.The station numbers which may be assigned to this function are No. 201 through 232. Registration of the personal number at any other station than these specified stations while the corresponding lamp is on causes that lamps to go out.

3.The destination indication panel must be made using use of the Data Transmitting and Receiving units.

For further details,

please refer to instruction

manuals for the DT-E70

and the DR-B61.

The lamp on the Destination panel is turned on

Lamp on

At station

No. 202

personal number

The lamp on the Destination panel is turned off

Lamp off

Mr. A

At any station

personal number

—56—

Calling Party Indication (Lamp Type)

A one station/one lamp type calling party indication panel can be provided for certain specified stations (eight stations or eight groups of stations)

The system can also be divided into a maximum of 8 groups of stations (consecutive station numbers) so that each group may have the calling party indication panels which are common within the group. The party making the call is indicated even if the call is made to any station in the group.

<Calling station memory>

It is also possible to equip the system with the "Calling station Memory" function. With this function, the calling party's lamp remains lit on the indication panel even if he cancels the call when the called party is on another line or in Privacy mode.

< Indication mode without calling station memory >

1.A lamp of the calling station comes on and goes out when the conversation is over.

2.When the call is made during conversation or privacy mode, a lamp of the calling station comes on and goes out when the calling station cancels the call.

<Indication mode with calling station memory >

1.The lamp at the station receiving the call comes on when a call is made and goes out when the conversation is completed.

2.When a call (camp-on-busy) is made to the busy or the privacy station (with the privacy switch on), the lamp of calling station comes on. The lamp will not

 

go out even if the original call is cancelled.

3.

The lamp goes out after the conversation is canelled.

4.

Dialing

without placing a call causes all lights to go out. *1

Note.

*1. In the case of Handset Master station TL-600M, lift a station handset and confirm that a dial tone is heard. Press after cancelling the dial tone by pressing

1.The maximum number of calling stations is 256.

When 2 or 3 exchanges are connected by tie-lines, the party who is calling through the remote extension exchange is not indicated.

2.The indication panel must be used with the Data

Transmitting and Receiving Units.

3.No.200 programming must be established in exchange

"A" for stations or station groups to have the indication panel. Similarly, No.470 programming must be established in exchange "B" and No.740 programming in exchange "C".

4. If the lamp type calling party indication function is used, this makes it impossible to use the lamp type conversation partner indication function.

Indication panel at station No. 239

No.208

Camp-on-busy

No.239

No.201

Conversation

Example of registration

Indication

First station

Last station

panel

number

number

1

 

 

2

239

239

3

 

 

4

 

 

5

251

255

6

 

 

7

 

 

8

 

 

1.Station No. 239 has the indication panel No.2.

2.The group of stations No. 251-255 is provided with the indication panel No. 5.

—57—

<Response to indicated calling party>

If, during the conversation, the called party wishes to respond the calling party indicated on the panel, he can do so by pressing either.

1. (calling party's No.) (the conversation is terminated) or

2. (calling party's No.) (the conversation is placed on hold temporarily).

Calling Party Indication ( Numerical Type)

A maximum of 32 stations (No.201~No.232) can have a numerical type calling party indication panel.

1. The first conversation partner (regardless of whether he is a calling or called party) is indicated at the "Conversation partner number" with 7 segment display.

2.When these is an incoming call during the conversation or to the station having its Privacy in ON position, the calling station number is indicate at the "Waiting station number", with the "Number of waiting stations" showing 1. If there are other stations waiting, the station numbers are stored but not indicated. A maximum of 8 waiting stations can be indicated. Even if a call is cancelled by a waiting station, the indication is not cancelled.

3.When a call is placed to a station in the wating station mode, the next waiting station is indicated.

4.If a call is finished, the indication is turned off.

5.To cancel the waiting station without responding, dial and the next waiting station is indicated. *1

Note.

 

*1. In the case of

Handset Master station TL-600M, lift

a station handset and confirm that a dial tone is

heard. Press

after cancelling the dial tone by

pressing

 

1. If the number of waiting stations exceeds 8, the indication for the station that has been waiting for the longest period of time is cancelled and the next station moves into that place.

2. Produce the indication panel using the Data

Transmitting and Receiving Units or use the master station HF-250M with liquid crystal display. For further details, refer to "Installation hand Book for CP Unit and Operation Instructions for the DT-E70, DR-B61 and HF-250M".

Indication panel at station No. 239

No.208

Responding to a selected

calling party

No.239

No.201

Conversation

(Station No. 201 is disconnected)

or

(Station No. 201 is hold)

Indication panel at station No. 231

Calling station

Waiting station

Number of

waiting

number

number

stations

No.235

Camp-on-busy

No.234

During a call

No.231

 

 

having an indication

panel

—58—

Conversation Partner Indication (Lamp Type)

A one station/one lamp type Conversation partner indica-

Indication panel at station No. 239

tion panel can be provided for specific stations (eight

 

 

 

stations or eight groups of stations). The system can be

 

 

 

divided into max. 8 groups of stations (consecutive station

 

 

 

numbers) so that each group may have the Conversation

 

 

 

partner Indication panels which are common within, the

 

 

 

group. The party making the call and the party receiving

 

 

 

the call are indicated whenever the calls are made to and

 

 

 

made from any station in the group.

 

 

 

1. When a station having the Indication Panel makes a

 

 

 

call, a lamp of the called station lights on until the

 

 

 

conversation is cancelled.

 

 

No.239

2. When a station having the Indication Panel receives

 

 

 

 

 

a call, a lamp of the calling station lights on until the

No.201

conversation is cancelled.

Conversation

Note.

 

 

 

The waiting station making a call to the station

 

 

 

(Camp-on-busy, privacy on) is not displayed on the

 

 

 

Indication Panel.

 

 

 

Group assignment for this function should be equal

 

 

 

to ''Conversation Partner Indication'' group assign-

 

 

 

ment.

 

 

 

Indication panel should be used with the Data Trans-

 

 

 

mitting and Receiving Units.

 

 

 

 

 

 

 

 

 

 

 

—59—

Pocket Pager

• Pager call and response

The system can call a maximum of 10,000 pager receivers and the party called can answer the call via the nearest station.

It is also possible to call those pager receivers having voice or display functions.

1. Paging

 

(1) Tone-only pager

Pager transmitter

The following two methods are available for calling tone-only pagers.

1. When there is no response from the called party to the call made by dialing the station number or personal number, further dial as follows without

terminating the call:

Pager call

Confirmation tone is heard.

and the call is connected to the called party's pager receiver.

Pager receiving call

2. To call the receiver directly, dial

Confirmation tone

Pager No.

Response call

The calling station, while wating for a response from

the pager, can receive other incoming calls.

Response

(From the nearest station)

Table showing paging operation 1 and output digits for pager calls

Pager digit

Two-digit

Three-digit

Four-digit

dialing

dialing

dialing

 

2 digits

Station No.

Station No.

Station No.

3 digits

-

Station No.

Station No.

4 digits

Personal No.

Personal No.

Station No.

Personal No.

 

 

 

(2) Pager with speech or display function

First dial and then both the pager and function code numbers according to the pager operating instructions.

Pager No.

 

After all operations are completed, dial

or replace

the handset.

 

—60—

2.Answering

To respond to the pager call, go to the nearest station and dial:

Pager No.

3.Automatic pager call

Register the station for this function using No.200 programming. When the station receive a station or personal number call, that call is automatically connected to the pager.

Notes.

1. No.200 programming must be established to register a pager output digit.

2. A maximum of 16 pager receivers can be called at a time.

3.A person called by pager has to respond quickly from the nearest station. Otherwise he cannot receive other calls during 3 minutes after the pager call has been made.

General Purpose Control

Station may be restricted from access to this function. This function can control other equipments by employing the Data Transmitting and Receiving Units.

Select the required type of output.

(Mode 1) One-shot make output (500/50 contacts)

Dial

0 ~ 49

(000 ~ 499)

and the relay output is made for 1 to 2 seconds. Example: Door remote and VTR control

Note: Operation performed even when all link circuits are occupied.

(Mode 2) Make/break output (512/100 contacts)

Dial

00 ~ 99

(000 ~ 511)

and the make output is sent out. Dial

00 ~ 99

(000 ~ 511) and the break output sent out.

Example: In/out annunciation, Prescription annunciatior

(Mode 3) 8-selectable one-shot make output (9 units)

Dial

1 ~ 9

1 ~ 8

Unit No. Contact No.

and one contact out of 8 selectable make outputs is obtained for about 1 or 2 seconds.

Example: VTR control

(Mode 4) 8 selectable make output and/or decimal output

(A)8 selectable make output (64/9 units)

Dial

1 ~ 9 1 ~ 8, 0 (Clear)

(01 ~64) Condition No. Unit No.

and one of the 8 relay outputs is made. "Clear" operation makes all 8 relays break.

Example: Destination indication, room condition indication, ITV control

(B)Decimal output

Dial

1 ~ 9

0 ~ 9

(01~64)

Condition No.

Unit No.

 

and the condition is indicated numerically. Example: Destination indication, room condition

(Mode 5) 4 decimal digits output

Dial

1 ~ 9

0000 ~ 9999

Unit No.

4 decimal digits

and 4 decimal digits are indicated. Example: Prescription annunciation

Door remote control

Fig. 1 Control with one-shot make output

Fig. 2 Lamp on/off indication panel

Fig. 3 VTR control with 8-selectable one-shot make output

Fig. 4 8 selectable output type indication panel

Fig. 5 Decimal output type indication panel

Fig. 6 4 decimal digits type indication panel

—61—

Simplified Paging

If an external speaker is connected instead of a station, simplified paging can be made without the PA amplifier when the caller dials that station number and makes a paging call.

Simplified paging

Note.

For further details, refer to "Installation Handbook for Exchange"

External speaker connected to the station

(No.234)

Clear Entry and Conversation Over

1.Clear entry

In the event that an error has been made when dialing

for Transfer or Conference, at the start of or during the conversation, dial

This will restore the condition before the error was made, allowing the caller to make a correction with- out interrupting the call.

2. Conversation over

 

To terminate conversation dial

or hang up a handset.

—62—

Chapter 3

Functions and operating procedures of tie-line system

Tie-line Connections of Exchanges

Tie-line

1.Purpose of tie-line connection

The EXES-6000 system incorporating the CP-66 central processing unit permits the use of a single exchange as well as the tie-line connection of 2 or 3 exchanges.

The tie-line connection is used when

1)connecting 2 or 3 exchanges installed in locations which are remote from each other (Maximum distance: About 2km. Cable: 0.65mm in diameter).

2)one more exchange, in addition to the existing exchange, is required for system expansion.

Tie-line

Station

(No. 200 ~ 455)

 

 

Conversation

Tie-line

Tie-line

("C"-"A")

("A"-"B")

Conversation

Tie-line

Station

("B"-"C")

(No. 470 ~ 725)

Station

Station

Station

(No. 200 ~ 455)

(No. 470~725)

(No. 740 ~ 995)

2. Number of stations, paging zones and links

 

 

Maximum number

Number of links

 

Maximum number

Maximum number of stations

 

 

Number of

in each exchange

Composition of exchange

of links within

 

 

of paging zones

 

 

one's own

exchanges

 

exchanges

 

 

 

 

 

 

Without paging

With paging

 

 

exchange

 

 

 

 

 

 

 

 

 

 

EX-610

12

 

1

All station calls

56

48

Without Tie-line

 

+ 7 zones

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

EX-620

16

 

1

All station calls

120

112

 

 

+ 7 zones

 

 

 

 

 

 

 

 

 

EX-1

EX-630

16

 

1

All station calls

256

256

 

 

+ 31 zones

 

 

 

 

 

 

 

 

 

 

EX-610

12*

1

8

 

2

All station calls

112

96

2 exchanges Tie-lines

 

 

+ 14 zones *4

 

 

 

 

 

 

 

 

 

 

EX-620

16*

1

8

 

2

All station calls

240

224

 

 

 

+ 14 zones *4

EX-2A EX-2B

 

 

1

2

 

2

All station calls

512

512

 

EX-630

16*

 

16*

 

+ 30 zones *4

3 exchanges Tie-line

 

 

1

4 per Tie line

 

3

All stations calls

168

144

EX-3A EX-610

12*

 

 

+ 21 zones *4

 

EX-620

16*

1

4 per Tie line

 

3

All stations calls

360

336

 

 

 

+ 21 zones *4

EX-3B EX-3C

EX-630

16*

1

8 per Tie line *

3

3

All stations calls

768

768

 

 

+ 45 zones *4

 

 

 

*1 Speech links of the local exchange are also used for communication between exchanges. *2 One (8 links) or two tie-line interface (TI-62) are required per exchange.

*3 Two tie-line interface (TI-62) are required per exchange.

*4 All-call paging from one exchange is placed over the whole area of all exchanges connected. *5 Different types of exchanges (EX-610/620/630) can be combined for tie-line connection.

—63—

3. Numbering Schedule for Stations and Paging Zones

Standard schedule (when personal Nos. are provided)

 

 

Numbering for stations

Numbering for paging zones

Type of exchange

System

 

 

Paging zones/exchange

 

 

Without paging

With paging

 

 

 

 

 

 

 

All station calls

Zones

 

EX-610

200~263

200~255 (247)*1

 

01~07

(15)*1

EX-1 (Single)

EX-620

200~327

200~319 (311)*1

 

01~07

(15)*1

 

EX-630

200~455

200~455

 

01~07 (31)*1

 

EX-610

200~247, 256~263

200~247

 

01~07

A

EX-620

200~311, 320~327

200~311

 

01~07

EX-2A/EX-3A

 

 

 

 

 

 

 

 

EX-630

200~455

200~455

 

01~15

 

 

 

 

00

 

 

 

EX-610

470~517, 526~533

470~517

 

08~14

(16~22)*2

B

EX-620

470~581, 590~597

470~581

 

08~14 (16~22)*2

EX-2B/EX-3B

 

 

 

 

 

 

 

EX-630

470~725

470~725

 

16~30

 

EX-610

740~787, 796~803

740~787

 

15~21 (31~37)*2

C

EX-620

740~851, 860~867

740~851

 

15~21

(31~37)*2

EX-3C

 

 

 

 

 

 

 

EX-630

740~995

740~995

 

31~45

*1 When the paging dial operations is set for

*2 When the EX-610 or EX-620 is connected to the EX-630 by tie-line.

When no personal Nos. are provided

 

 

Numbering for stations

Numbering for paging zones

Type of exchange

System

 

 

Paging zones/exchange

 

 

 

Without paging

With paging

 

 

 

 

 

 

 

All station calls

Zones

 

EX-610

100~163

100~155 (147)*1

 

01~07

(15)*1

EX-1 (Single)

EX-620

100~227

100~219 (211)*1

 

01~07

(15)*1

 

EX-630

100~355

100~355

 

01~07

(31)*1

 

EX-610

100~147, 156~163

100~47

 

01~07

A

EX-620

100~211, 220~227

100~211

 

01~07

EX-2A/EX-3A

 

 

 

 

 

 

 

 

EX-630

100~355

100~355

 

01~15

 

 

 

 

00

 

 

 

EX-610

400~447, 456~463

400~447

 

08~14 (16~22)*2

B

EX-620

400~511, 520~527

400~511

 

08~14(16~22)*2

EX-2B/EX-3B

 

 

 

 

 

 

 

EX-630

400~655

400~655

 

16~30

 

EX-610

700~747, 756~763

700~747

 

15~21 (31~37)*2

C

EX-620

700~811, 820~827

700~811

 

15~21 (31~37)*2

EX-3C

 

 

 

 

 

 

 

EX-630

700~955

700~955

 

31~45

*1 When the paging dial operations is set for

*2 When the EX-610 or EX-620 is connected to the EX-630 by tie-line.

—64—

Restricted Conditions for Tie-line Connection

 

 

 

 

 

Tie-line

1. Paging

 

 

 

 

 

4. Below are functions that can be operated for the same

1)

Paging is possible for up to 15 zones per exchange.

exchange but cannot be operated extending over more

2) The whole area of all exchanges can

be called

by all-

than one exchange connected by tie-line.

 

 

call paging.

 

 

 

 

 

1) Remote Response

 

3)

It is possible to

make an all-call paging and an indivi-

2)

Master/Sub Relationship

 

 

dual zone paging from any master station.

 

 

3)

Call Transfer

 

4) It is possible to

respond to all-call

paging from any

4)

Paging during Normal Calls

 

 

master station.

 

 

 

 

 

5) Group Hunting

 

5) A response to

the individual zone

paging is only

6)

Secretary Transfer

 

 

possible from the station connected to the exchange

7) General

Purpose Control (One-shot

Make Output,

 

corresponding to that paging zone. If the Automatic

 

Make/Break Output, 8 Selectable Make Output,

 

Paging Response (

) is employed, a response to

 

Decimal Output, 4 Decimal Digits Output). Even

 

the zone paging is only possible from the station

 

when dialed correctly, different indications result or

 

(consecutive number)

which belongs to

that

zone.

 

unintended control equipment are operated if the

6) Paging assignment is

impossible beyond

the

local

 

function

extends over more than

one exchange.

 

exchange.

 

 

 

 

 

8) Calling Party Indication (Lamp Type)

 

 

 

 

 

 

 

 

9)

Pager Call

 

 

2. Programmable Station Numbering

It is possible to change station numbers of each exchange within the limit specified in "Selectable numbering schedule of each exchange".

3.Group Blocking

1)The system can be divided into a maximum of 6 groups per exchange.

2)It is possible to set up the calling and called groups as desired within the same exchange.

3)Only one pair of stations can call each other between exchanged connected by tie-line.

4)Arbitrary station groups can be restricted to access all-call and individual zone paging.

5)Calling and called groups must be set up to make a paging response possible. The paging response is possible from the called group to the calling group

(reverse direction of call restriction).

—65—

EXES-6000, CP-66 Summary of Dial Operations (For Tie-Line System)

Function

Dialing operation

Press-to-talk

Remote response

Remote response registration

Answering continuous calling tone

Privacy

Secretary transfer

Single-digit registration

Single-digit dialing

Personal number registration

In/out indicator lamp ON

Personal number cancellation

In/out indicator lamp OFF

Personal number call

Conference

Conference clear

Busy call back registration

Busy call-back response

Highest executive priority

Call transfer

All call

+ 45 -zone paging

All call paging response

Zone paging response

Paging transfer

Tie-line

Number assignment

—66—

Tie-line

Function

Dialing operation

Number assignment

One-shot, relay-make output

Relay make-break output

8-selectable, one-shot, relay make output

8-selectable output

(Decimal output)

4-digit decimal output

Pager call

Pager response

Calling station selection

Message recording

Message check

Message playback

Message cancellation

Remote message playback

Clearing calling party indication

BGM

—67—

Camp-On-Busy

When the party you are calling is on another line, by simply waiting you automatically "Camp-On" the line. (Busy tone sounds continuously.) As soon as the line is freed, you will be automatically connected.

After call

Call

Busy Call Back

When the called station is busy, dialing

permits this function to be registered and terminates the call after a confirmation tone. As soon as the line is freed, the calling party is called by the distinctive "busy-call-back" tone that sounds for 10 seconds. By one-touch dialing any

one of

key during the 10-second

period, the calling party can be connected to the called party.

The disadvantage of the camp-on-busy function is that a link is occupied and busy tone is heard from your station all the way while you are waiting. This problem can be avoided by using the busy call back function that can improve the availability of speech paths as well as enables you to wait without being annoyed by "noisy" busy tone.

A maximum of 15 stations can be registered for this function. Once the function has been programmed into your station, you are put in the simple "busy waiting" mode even when you depress 6 in an attempt to register other busy stations for this function.

It is possible to make or receive other calls while waiting after this fuction has been programmed. However, if you are still using your station for conversation with the third party when the busy station registered for this function is freed, the registered busy call back function will be cancelled.

Camp-on-busy is prior to busy call back.

Registration

Busy tone

Conversation

Calling station

Called station

Line has been freed.

Busy call back tone

Calling station

Calling

 

 

 

(Any key other than

Called station

—68—

Privacy

Shift Privacy Switch to ON.

When a party does not wish to accept incoming calls, this function may be employed to refuse them. With the Privacy switch in the ON position, a continuous privacy tone will be sounded in the station making the call, and at the same time, a brief Privacy tone will sound in the station called, indicating a call attempt is being made.

It is possible to call the other party from the station in the Privacy mode but Remote Response is impossible from that station.

Shift Privacy Switch back to the left.

To restore a station in the "Privacy" mode to a normal condition, and thus ready to receive calls.

Note: 1. A call received while the station is in the Privacy mode may be accepted if the Privacy function is immediately cancelled. (see Camp-On Privacy)

2. In the event of the station registered for the Secretary Transfer function, the Privacy switch is used on and off operation of the Secretary Transfer function. (see Secretary Transfer)

3.During the above "Privacy" mode, while the call-

ing station has the bar depressed, the privacy tone stops and the caller can transmit a one way message.

When the bar is released, the normal "Privacy" mode to be resumed.

Tie-line

PV Type

 

One tone

Privacy tone

Call

—69—

Camp-On Privacy

When the party you are calling has his station on Privacy mode, by simply waiting you will automatically "Camp-

On" the line. (Privacy tone sounds continuously.) As soon as the Privacy mode is released, or as soon as he one-touch dials any of the keys (), or as soon as he picks up a handset of his station, you will be automatically connected.

This function is canelled automatically if the station in the privacy mode may not accept the call within approximately

10 seconds.

Tie-line PV Type

Automatic

Press-To-Talk

This function is activated when the

(Press-To-Talk Bar)

is continuously depressed after dial tone confirmation or during hands-free conversation. This allows one-way conversation from the party depressing the function key. When the key is released, one-way conversation is reversed.

Employ when a person in a high noise level area is called by a person in a quiet area, or when no particular response is required, or when simple announcements are made. In such cases, one-way conversation flow can be used.

One-way conversation is activated while the Press-To-Talk bar is continuously depressed.

As long as the Press-To-Talk bar is depressed by either party, the voice of the party using this function has dominance. When the key is released, the other party has dominance.

One-way conversation is reversed when the Press-To-Talk bar is released.

If both parties depress the Press-To-Talk bar, the voice of the party who depresses the bar last will have dominance.

Depress the

to return to ordinary hands-free 2-way conversation ........

Note.

One-way conversation is impossible even if the bar is depressed unless either party or both parties involved pick up a handset.

—70—

Single Digit Dialing

Tie-line

Single digit registration

 

 

 

Register in advance as follows:

 

 

 

Confirmation tone

 

 

(Station number)

Station number

 

 

 

Confirmation tone

 

(Personal number)

Personal number

 

 

 

Confirmation tone

 

(Paging call)

Paging zone

 

 

 

Confirmation tone

 

 

(All-call paging response)

Confirmation tone

(Each function)

Any six digits

 

 

 

Confirmation tone

(Each function)

Any five digits

 

 

 

Confirmation tone

 

(Each function)

Any four digits

 

 

 

Confirmation tone

 

(Each function)

Any three digits

 

 

 

Confirmation tone

(Each function)

Any two digits

 

 

 

< Single digit dialing >

When required, dial

and the registered number will be called automatically.

Note: 1. To cancel the registration, dial the station number of the station at which this function has been registered.

2. It is also possible to use this function to shorten the long dial operation.

Example.

Combination paging

Single digit

Simply dialing makes the combination paging instead of dialing

3.Single digit registration is not available from any substation programmed by No.200 programming, even if its line is connected with master station.

—71—

Master Sub Relationship

Master/Substation associations are set up by using station #200 as the programming station. Once these relationships have been established, substations can then contact their designated master stations by simply touch dialing

If TL-600S Handset substation is used, it can be connected to its designated master station by simply picking up a handset.

With respect to this function, the stations in the system are divided into two categories; master stations and substations. Any master station can be connected to any other station in the system. However, substations can initiate calls only to. specific master stations. This is done by single touch dialing, and will only connect the substation to one specific master.

Also, one master station can have 2 or more substations.

To register this function, dial

Confirmation tone

Substation No. paired off with the master

at the master station. This allows the master station to be connected to the substation when is pressed.

Note.

Once a certain station number has been desgination as a substation by No. 200 programming, the single digit dialing is impossible even when the master station is connected to that number.

Tie-line

Substation

Master Station

Handset substation

Single Digit Registration of Substation

Master Station

Substation Number

Substation

Automatic Access To Paging

This function requires "single digit dialing registration for handset station" as well as No.200 programming at time of installation.

A paging call can be placed over the specified zone by simply lifting the handset.

A paging response is possible by simply lifting the handset.

—72—

Paging call

Fig. 1

Paging call

Paging response

Response to a paging call

Fig. 2

Personal Number Call

A personal number may be registered at any master station which the person to whom the number is assigned expects to be. A party wishing to receive personal number calls at a specific station may register his number at that station by touch dialing

Confirmation tone

Personal Number.

Those who are frequently away from their assigned station, as well as those who share a single station may be assigned a ''Personal" 4-digit number which may be programmed to any master station in the system. This personal number, which is completely independent of station numbers, may be programmed at any master station, and any previous programming of that same number at any other station is automatically cancelled. When the party calling has dialed the number to which he wishes to speak, the call is then routed to the station at which the Personal Number was last registered. The numbers which may be assigned in this group are 1000 through 1999.

Personal number program cancellation can be done at any station be merely dialing:

Confirmation tone

Personal Number

When anyone having a personal number leaves the office, he merely cancels the programming of his personal number. With the personal number cancelled, any incoming calls to that number will be answered by a dial tone, indicating that he is not available.

Note.

The maximum number of the Personal Number remains same even if the number of exchange to be connected is increased to 2 or 3.

Registration

Personal Number

Personal Number Call

Personal Number

Call

Station where the personal number is registrated.

Cancellation (At any station)

—73—

Continuous Calling Tone

Tie-line

When there is an incoming call to the specified station,

a calling tone is sounded continuously at the called station. The continuous calling tone stops if the called party presses

(except key)

1. Use this function when it is difficult to hear a brief single tone due to high background noise. Any station can be so made as to be called by the continuous calling tone, but No.200 programming is required for such a station (refer to Installation Handbook for EXES-6000 CP-66).

2.If the calling party presses the key while the continuous calling tone is being sounded, the continuous

calling tone stops to allow the caller's voice call to go through. Releasing the key restores the continuous calling tone.

3.If either party continuously presses the key

during the normal two-way conversion, this makes a one-way conversation from the party who pressed the

key. Releasing the

key reverses the one-

way conversation flow and the other party has a dominance (Press-to-Talk).

Notes.

1. In the NP type system that has no Privacy function, the station can be called by the continuous calling tone if its Privacy switch is set to ON. This function by No.200 programming is, therefore, used in the PV type system having the Privacy function or for the HF-670M industrial type station equipped with no Privacy switch.

2.The following stations can be called by the continuous calling tone:

(1)Stations in the "NP" type system or specified substations in the "PV" type system.

(2)Stations registered for continuous calling tone by No.200 programming.

Continuous calling tone

Continuous calling call

Continuous calling tone

Call

(Any key other than

< Station vs. calling tone >

Type of system

"PV" Type

"NP" Type

Type of station (Specific station provided with

"continuous calling tone" function by station No.200 programming)

Non-programmed station (standard)

Programmed station

Handset programmed station

Non-programmed station (standard)

Programmed station

Responding to a call made by continuous calling tone

Type of calling tone

Privacy switch in OFF position

Privacy switch in ON position

Single "trill" calling tone

Privacy tone

(Call is put through immediately

 

after calling tone)

 

Continuous calling tone

Privacy tone

-

Continuous calling tone

Single "trill" calling tone

Continuous calling tone

(Call is put through immediately after

 

calling tone)

 

Continuous calling tone

Continuous calling tone

Depress any dial key other than

1 . Depress only dial key other than

key.

key.

 

2. Pick up a handset.

 

3. Shift Privacy switch to OFF.

—74—

Remote Response

A call to a certain station can be remotely responded to from the other station by simply depressing while a continuous call tone is ringing or within 5 seconds after a brief call tone has stopped ringing.

Notes.

1.The Remote Response is only possible among stations programmed for this function.

2.When making the remote response from the station having its Privacy switch in ON position, shift the

switch back to OFF or lift its handset before depressing

Programmingtheremote response group

Establish the remote response group of stations and designate a specific station within the group as a temporary "Master station" and the rest as "Substations".

Set up the "Master station" by dialing.

Confirmation tone

Station No. to become "Master station".

Register the "Master station" No. at the "Substation" by dialing

Confirmation tone

Master's number

Note.

Be sure to register the station No. that becomes the "Master station" at the "Master stations".

Cancelling remote response programming

Touch dialing at each "Substation"

Confimationtone

His own Substation number

cancels the Remote response program.

Note.

When 2 or 3 exchanges are connected by tie-line, select the Remote response group within the stations connected to the same exchange.

Tie-line

Dial operation for Remote response

Calling tone

Calling

Station

No.201

No.209

No.203

Remoteresponsegroup

Conversation after Remote response

Conversation

Station

No.201

No.209

No.203

Remote response group

Programming the remote response group (Example)

Station

No.201

Station

Station

Station

No. 204

No. 203

No. 202

Remote response group

—75—

Call Transfer

Tie-line

Call Transfer from Called Station

During the conversation, first dial

(the Station Number of the person the call is to be transferred to).

The original call is then held and the holding tone is transmitted to the other party, while the third party is called and asked whether he will accept the call. If he agrees to accept the call, dial or hang up a handset,

and the transfer will be completed.

This function allows called party to transfer that call to another station. The party to whom the call is to be transferred, may be called using either the Station Number, the

Personal Number or through Single Digit Dialing.

Call Hold and Call Back from Calling or Called Station

During the conversation, first dial

(Station Number of the third party.)

The other party is then placed on hold while the third party is called. Upon completion of the conversation with the third party,

dial

or the third party dials

or the third party replaces a handset.

This allows the original conversation to resume.

The Transfer function is combined with the Call Holding function.

When two parties are talking, either one can be temporarily placed on hold to permit the call to another station. When the conversation with the third party is over, the original conversation can be resumed.

The third party can be called using either the Station Num- ber, his Personal Number or through Single Digit Dialing.

Note.

When 2 or 3 exchanges are connected by tie-line, an original call can be transferred only to the third party who shares the same exchange with the party who transfers the call.

Called Station

Third Party

Call Back

Call

Called Station

Calling Station

Called Station

Transfered Station Number

Called Station

Calling Station

Holding

Call

Third Party

Transfer

Called Station

Called Station

Calling Station

Call

Third Party

Called Station

Calling Station

 

Original Call

Third Party

—76—

Paging during Normal Calls

A paging call can be made by a called party of an existing call to a third party, the third party's response accepted while the original call is on hold, and the original call resumed when the response call has ended.

Press

and the desired zone number. This puts the original call on hold and makes the External PA and or Station paging call. Then, press

to restore the original call, and wait for the response to the paging call. When the response is received, press

or replace the handset and the original call goes back on hold allowing the second call to the taken. When the second call is completed, press

and the original call can be resumed.

•When EX-610 or EX-620 is used.

Note.

1.With adoption of the selective functions "Call Transfer" and "Paging", this function is allowed to activate.

2.When 2 or 3 exchanges are connected by tie-line, paging during a normal call is only possible within the paging zones allocated to the exchange to which a station making the paging is connected. An All-call paging during a normal call is impossible.

Group Hunting

When the party you are calling is on another line, your call is automatically rerouted to another station which is pro- grammed from the beginning.

When the party to whom the call is rerouted is also on another line, the call can further be rerouted to the other station by programming.

Note.

1.To use this function, station No.200 programming of the station number(s) to which the call is to be trans- ferred must be set up in the exchange. Place a DIP switch for Group Hunting in the ON position and make Group Hunting programming, so that this func- tion can be programmed.

2.The combined use of this function with the

"Secretary Transfer" function makes the system more functional. When "Secretary Transfer" function is employed, setting the Privacy switch to the ON position allows any incoming call to be automatically transferred to the other stations even when one is absent.

3.If station No. 200 programming is made so that the call can be rerouted to the station which is called first when the other stations registered are busy, then any call can be transferred automatically to another station.

Similarly, the original call can be rerouted one after another in the "Secretary Transfer".

4.When 2 or 3 exchanges are connected by tie-line, select the station to which the call is to be transferred within the same exchange group.

Tie-line

Conversation

Calling party

Called party

 

Station paging

On hold

External PA paging

Resuming

the original call

—77—

Secretary Transfer

This function is only available when a specified station is programmed for this purpose with use of Station #200 in the programming mode. Automatic transfer of incoming calls by an executive to his secretary is accomplished by placing the Privacy Switch on his station in the ON position.

This function allows a secretary to accept all incoming calls placed to an executive.

For the executive to accept calls directed to his station once the automatic secretary function has been program- med by station #200, he simply moves the privacy switch to the left, or OFF position.

It is also possible for the executive to accept calls at his station.

There is no limit to the number of Executive/Secretary pairings except by the number of available number combinations within a given system.

When a secretary who is already programmed for this func- tion wishes another secretary to accept all incoming calls directed to an executive, station No. 200 programming of another secretary should be set up in the exchange. Then, the calls can be rerouted to another secretary if the executive and the secretary first registered place their Privacy switches in the ON position. It is also possible to transfer the call in a daisy chain method.

Note.

When 2 or 3 exchanges are connected by tie-line, set up a Secretary/Executive association within a group of stations connected to the same exchange.

Secretary

Digit the executive station.

Tie-line

Executive

—78—

Secretary Transfer and Call Transfer

Combination of the secretary transfer and call transfer allows rerouting of the call transferred to the secretary back to the executive's station.

When the secretary answering a call touch dials

Executive's station number

the privacy tone sounds continuously at both stations,

while

the call

is held.

The

holding tone is

transmitted

to the

calling

station.

If the

executive shifts

the privacy

switch to the left position, or if he depresses any of the keys other than the key or picks up a handset he can talk with the secretary. If

the call held is to then be transferred

back to the execu-

tive's station, the secretary is to touch dial

, or to

hang up a handset, and the original

calling

station will

be connected to the executive's station.

 

 

Secretary Transfer and Call Transfer using Single Digit

Dialing

Combination of "Secretary Transfer", "Call Transfer" and "Single Digit Dialing" allows simple retransfer of the call transferred to the secretary back to the executive's station.

Touch dial

Confirmation tone

Executive's station number

at the secretary's station in advance. When the call transferred to the secretary has to be transferred back to the executive, the secretary simply touch dials

at her station. This sends the continuous Privacy tone to both stations while the call is held. If the call is to be transferred back to the executive's station, the secretary touch dials or hangs up a handset.

The calling station will then be connected to the executive's station.

If there is no answer from the executive, the secretary touch dials

and the original call is resumed.

Unless the executive sets his station Privacy switch to OFF within 10 seconds after the Privacy tone has sounded, the call attempt to the executive is cancelled for automatic return to the original conversation.

Tie-line PV Type

Call

Secretary dials

(Executive)

Privacy tone

Pr vacy Tone

Holding tone

Holding

Executive

or depresses any of the keys

or picks up a handset

Holding tone

Call

Call Transfer

Call Back

Secretary dials

Secretary dials

or hangs up a handset

Call Transfer

—79—

Secretary Transfer and Call Transfer

Adoption of the selective function "Transfer" allows rerout- ing of the call transferred to the secretary back to the executive's station.

When the secretary answering a call touch dials

Executive's station number

the continuous calling tone sounds at both stations, while the call is held. The call holding tone is transmitted to the calling station. If the executive shifts the privacy switch to the left position, or if he depresses any of the keys other than the key or picks up a handset he can talk with the secretary. If the call held is to then be transferred back to the executive's station, the secretary is to touch dial , or to hang up a handset, and the original calling station will be connected to the executive's station.

Secretary Transfer and Call Transfer using Single Digit Dialing

Adoption of the selective functions "Transfer" and "Single Digit Dialing" allows simple retransfer of the call transferred to the secretary back to the executive's station.

Touch dial

Confirmation tone

Executive's station number

at the secretary's station in advance. When the call transferred to the secretary has to be transferred back to the executive, the secretary simply touch dials

at her station. This sends the continuous calling tone to both stations, while the call is held. If the call is to be transferred back to the executive's station, the secretary touch dials or hangs up a handset.

The calling station will then be connected to the executive's station.

If there is no answer from the executive, the secretary touch dials

and the original call is resumed.

Tie-line NP Type

Call

Secretary dials

(Executive)

Continuous calling tone

Continuous

calling tone

Holding tone

Holding

Executive

or depresses any of the keys

or picks up a handset

Holding tone

Call

Call Transfer

Call Back

Secretary dials

Secretary dials

or hangs up a handset

Call Transfer

—80—

Highest Executive Priority

This function is available only for those stations specifically programmed for this function, with programming station No. 200. When the station called is busy, as indicated by the busy or privacy tone, dialing

sends a priority tone. This priority tone is transmitted for a few seconds and then the call is put through, terminating the original conversation.

When the called station is busy or in the Conference mode or during a paging call, this function allows forced interruption for priority conversation.

*When the party called through the conference function is busy and it desirable to interrupt his conversation, dial

Priority

Tie-line

Original Conversation

Busy Tone

Priority Call

Conversation Over

—81—

Conference

A "Hands-Free" conference call can be made with up to 4 persons. For a conference under this function the other participants may be called either through their station number, personal number or by Single Digit Dialing. Addition of stations or personal numbers (total of only 4) may be added by anyone already connected.

The person who proposes the conference may dial

(Station Number of the 1st of the participants)

After receiving 2nd person's consent, he may then dial

(2nd participant)

After receiving 3rd person's consent, he may now dial

(the last participant)

At this point, the 4-man conference may begin. It is also possible for any of the 4 participants to call up any of the other participants.

Both the 2nd and the 3rd persons can be called up in one dial operation without obtaining their consents.

A person wishing to drop out of the conference should dial

or hangs up a handset

at his station.

Any of the participants who wish to drop out during the conference may do so as long as it's not the party who originated the conference.

The function is cancelled and the normal mode is restored when the person who arranged the conference dials

In the event that the calls made by the person arranging the conference are not answered or that there has been a dial- ing error, the function can be cancelled for restoration to the normal mode.

The conference is terminated when the party who arranged the conference dials

or hangs up a handset

When the conference has been terminated by the party who originated it, the other participants cannot continue the conference.

Tie-line

A "Hands-Free" conference call can be made with up to 4 persons.

Dialing of conference member.

Station number

Personal number

Single Digit

—82—

Paging

A variety of paging modes allows paging over a wide area from any master station. The paged party may respond from the nearest master station.

Paging modes include external PA systems and/or Station paging, and Zone paging is for calling a limited area and

All-call paging is for calling over the entire area.

Response to a paging call may be made by means of Automatic response or Zone number dialing.

1. External PA paging and Station paging

A.External PA paging

1.Paging through external speakers is possible from any master station, with the paged party able to respond from the nearest master station.

2.External PA paging zones and all-call paging are possible up to a maximum number of 15 zones per exchange.

3.A maximum of 30 zones can be connected when 2 exchanges are tie-lined and 45 zones for 3 exchanges.

B.Station paging

1.Paging from any master station to all stations within a certain area is possible through the station speakers. But the page will not be heard at stations in use in the

area.

2.Zone paging and all-call paging are possible up to a maximum number of 15 zones per exchange.

3.A maximum of 30 zones can be connected when 2 exchanges are tie-lined and 45 zones for 3 exchanges.

2. Zone paging and All-call paging

A.Zone paging (Individual zone paging).

Paging and Paging response are possible through Zone paging. The same paging zones (Exchange A: No. 1 ~ 15,

B:No. 16 ~ 30, C: No. 31 ~ 45) are used for PA paging

and Station paging. Therefore, both PA and Station paging calls are possible in the specific zone connected for the both paging functions.

To page, depress

Zone No. (01 ~ 45)

To respond to a zone paging, depress

Zone No. (01 ~ 45)

B.All-call paging

Paging and Paging response for External PA or station paging is possible through All-call paging. All-call paging is possible over the zones (No. 1 through 45) connected for PA or Station paging, and it is possible to make the paging response from any station. However, the station

not connected to any of the paging zones is not paged. This does not necessarily mean that All-call station paging must reach all the stations.

To make a all-call paging, depress

To respond, depress

 

 

 

 

 

Tie-line

C. Maximum paging zones

 

 

 

 

No. of

Kind of Exchanger

Station paging

Public address

Exchanger

 

paging

 

 

 

 

 

EX-610/620

All station calls

All station calls

 

+7

zones

+7 zones

(1)

 

 

All station calls

All station calls

 

EX -630

 

+15 zones

+15 zones

 

 

 

EX-610/620 : EX-610/620

All station calls

All station calls

 

 

+14 zones

+14

zones

(2)

EX-610/620 : EX-630

All

station calls

All

station calls

+22

zones

+22

zones

 

 

 

EX -630 : EX -630

All station calls

All

station calls

 

+30

zones

+30 zones

 

 

 

EX-610/620 : EX-610/620

All station calls

All station calls

 

: EX-610/620

+21

zones

+21

zones

 

EX-610/620 : EX-610/620

All station calls

All station calls

(3)

: EX -630

+29 zones

+29 zones

EX-610/620 : EX-630 :

All station calls

All station calls

 

 

EX -630

+37

zones

+37

zones

 

EX -630 : EX -630 :

All station calls

All station calls

 

EX -630

+45

zones

+45 zones

3.Responding to a paging call

A. Automatic response

1.Zone paging response Touch dialing

at the station within the paged zone permits a response to the party who placed a paging call.

In this event, No. 200 registration of the stations (consecutive station numbers) within each zone must be made.

2.All-call paging response Touch dial

at any station and the paged party is put through to the party calling.

B.Zone number dialing

1.Zone paging response

The paged party is connected to the party calling by depressing

Zone No. (01 ~45)

at any station.

A response to the zone paging is possible only from a station connected to the exchange that includes the paged zone.

2.All-call paging response Depressing

permits a response to the party calling.

—83—

How to select the paging area and make the paging call

Tie-line

If the EX-630

Dialing operation

is included in the

 

tie-line exchanges.

Paging area

 

Response

 

 

 

 

 

 

Paging call

Automatic

Zone number

 

 

 

 

 

 

response

dialing

All-call paging over the entire zones of exchanges

"A", "B"and "C"

*1

Zone paging to the zone

 

of

exchange

"A"

 

Zone paging to the zone

 

of

exchange

"B"

 

Zone paging to the zone

 

of

exchange

"C"

 

If the tie-line

 

Dialing operation

exchanges are the

 

 

 

 

EX-610 and/or

Paging area

Response

EX-620.

 

Paging call

Zone number

 

 

Automatic

 

 

response

dialing

All-call paging over the entire zones of exchanges "A", "B"and "C"

*1

Zone paging to the zone of exchange "A"

Zone paging to the zone of exchange "B"

Zone paging to the zone of exchange "C"

Note.

*1 When

2 or 3 exchanges are connected by tie-line

but 1

or 2 of them have no built-in Paging unit (PI),

All-call paging is made only over the area of the exchange(s) having the PI.

*2 A paging response is possible only from the station in the paged zone.

*3 A paging response is possible only from the station connected to the exchange "A" (station No.200 ~ 455)

*4 A paging response is possible only from the station connected to the exchange "B" (station No.470~

725)

*5 A paging response is possible only from the station connected to the exchange "C" (station No.740~ 995)

Paging zone

No.31 ~ 45

Paging zone

No.01 ~ 15

Paging zone

No.16 ~ 30

—84—

All-Call Paging and Individual Zone Paging

Paging call

External PA paging to a specific zone is possible from any master station by pressing after picking up a handset.

("00" = all-call)

(01 ~ 45) (*01 ~ 21)

It is possible to wait for a response in this mode, but anything said will be broadcasted over the entire zone. It is best to end the paging call by pressing

or hanging up a handset

and waiting for a response.

* When the tie-line system is using the EX-610 and EX-620.

All-call paging of zones 1 through 45 can be done in both the External PA paging mode through an external amplifiers and speakers, and the station paging mode through the station speakers. In the event of All-call paging, the paging is done over the entire zones.

When all-call paging is initiated during zone paging, the zone paging is interrupted and restored after the all-call paging is finished.

Paging response

1.Automatic response

To respond to a paging call, go to the nearest master station and press either

(All-call paging response) or

(Zone paging response)

A paging response is possible only from the station in the paged zone.

A response to All-call paging is possible from any station.

To respond to Zone paging by pressing

, No. 200

registration of the stations (consecutive station numbers) within each zone must be made. Such registration is required for both external and station paging.

2.Zone number dialing

To respond to a All-call paging, go to the nearest master station and press

To respond to a Zone paging call, press

Zone No. 01 ~ 45

at the nearest station.

A response to the zone paging is possible only from a station connected to the exchange that includes the

paged zone (Exchange "A":

Zone

No.

1

~ 15,

"B":

No. 16 ~ 30, "C": No. 31 ~

45). It

is not impossible to

respond from the station

connected

to

the

other

exchange.

A response to All-call paging is possible from any station.

Tie-line

All-call paging

Zone paging

Response to zone paging

Response to All-call paging

Table of stations used for individual zone paging (Example) (In the case of "Automatic response")

Zone

First station

Last station

numbers

number

number

—85—

Selectable First Station Number of Each Exchange

Tie-line

1.Standard station Numbering schedules of exchanges A,

B and C are as follows:

<Standard station numbering >

Type of Exchange

A

B

C

With Personal

200 ~ 455

470 ~ 725

740 ~ 995

Number (Standard)

 

 

 

2. If other numbering schedules are preferred, it is possible to choose the head number of each exchange from

100/200/300/400/500/600/700/800/900 in order of exchange A, B and C. (Stations of each exchange must have the consecutive numbers.)

< Example >

Type of Exchange

A

B

C

Example 1 With Personal Number

300~

500~

700~

Example 2

Without Personal

100~

600~

900~

Number

 

 

 

 

—86—

Programmable Station Numbering

1. This function allows the system to have "Programmable station numbers", other than the "Hardwired station numbers" by programming.

The stations not registered for "Programmable Station Numbers" remain in the original "Hardwired Station

Number".

2.Each station number can be programmed in the station number series of the exchanges A, B and C that have been determined by the function of the Selectable First Station Number.

1.Numbering schedules can be changed easily by programming in stead of rewiring.

2.Such numbering schedules as 200's, 300's and 900's can be grouped together for each individual office. (Refer to Fig. 1)

3.Hardwired stations of each paging zone must have consecutive numbers. To make the programmable station numbers inconsecutive, use this function. (Refer

to Fig. 2)

4.This function requires No.200 programming. See Installation Instructions for EXES-6000 CP unit.

Dialing

Exchange

Programmable station

 

No. 203

 

 

 

 

Circuit No. 201

 

 

(Hardwired station

 

 

number)

 

 

Circuit No. 203

 

 

(Hardwired station

 

 

number)

 

 

Programmable station

 

 

No. 201

5."Programmable station number" series for each exchange

< Fig. 1 >

Hardwired station number

<Fig. 2>

Hardwired station number

<Fig. 3>

Hardwired station number

Tie-line

Programmed station number

Department 1

Department 2

Programmed station number

Station

paging zone

Programmed station number

<Example 1> With Personal Number

<Example 2> Without Personal Number

<Example 3>

 

Exchange

Hardwired

Programmed

Exchange

Hardwired

Programmed

Exchange

Hardwired

Programmed

station number

station number

station number

station number

station number

station number

 

 

 

(Standard)

6.People operating the intercom stations need not worry about the Hardwired station numbers. Note, however, that the hardwired station numbers are used to program all the setup data of each function into the exchange through No.200 programming.

—87—

Group Blocking

Funtion (A)

The system can be grouped or divided into a maximum of 6 groups of stations with consecutive station numbers by exchanges "A", "B" and "C". Different station groups cannot call each another.

[Example 1]

< Exchange

"A" >

Fig. 1

< Exchange "B" >

Fig. 2

Group 1 No.201~209

Group 1

No.470~479

Group 2

Group 3

Group 4

Group 2

 

Group 3

No. 210~219

No.220~249

No. 250~279

No.480~489

No.490~499

Tie-line

< Exchange "C" >

Fig. 3

Group 1 No.740-759

Group 2

Group 3

No.760~769 No.770~799

Function (B)-1

The group connected to the same exchange can call and/ or be called by any other group(s) within the same exchange area.

Function (B)-2

Only one pair of groups can call each other across the tie-lined exchange. The tie-line link of each exchange (4

links) forms a group (

and

) like stations.

The groups No.1

through

6 connected to the same

exchange can call

exchange

by programming in tie-line

links (group No. 7) and (group No. 8).

[Example 2-1]

Fig. 4

 

 

 

Group 1

 

Calling station

Group 2

Group 3

Group 4

 

 

 

 

Station receiving

[Example 2-2]

< 2 exchanges tie-lined >

Fig. 5

 

< 3 exchanges tie-lined > Fig. 6

Explanation of < 3 exchanges tie-lined > (Fig. 6)

1) The call can be made from Group No. 2 of exchange "A" to tie-line links of exchange "A".

2)Connect tie-line links of exchange "A" to tie-line links of exchange "B".

3) The call can

be made

from tie-line links

of ex-

change "B" to

group No.

1 of exchange "B".

 

4)Thus, the call is allowed to go through from Group No.2 of exchange "A" to Group No. 1 of exchange "B".

Function (C)

The paging zone number (All-call, individual zones No.1 ~ 30 for 2 exchanges and No.1 ~ 45 for 3 exchanges) which each group of each exchange can call is programmable. (No distinction is made between external PA and

Station paging.)

Paging to the paging zones of the other exchange is also programmable.

Note.

When the paging call is made, the group of stations to which the response is made is restricted by Function B. Function B permits the normal station call in the direction of the arrows. Its paging response can be made in the opposite direction of the arrows.

(Refer to Fig. 4 and Fig. 8)

[Example 3]

Fig. 7

 

 

 

Group 1

 

All-call paging

Group 2

Group 3

Group 4

Zone 4 paging

 

 

 

[Example 4]

Fig. 8

Paging station

Paging zone

 

 

 

Group 1

 

Paging station

 

 

 

< Example of Paging response >

When the programming is set up for the normal station

 

 

Paging response

Group 2

Group 3

Group 4

call as is shown in Fig. 4, the paging response is only

 

 

Station responding to paging call

 

 

 

possible in the direction of the arrows of Fig. 8.

—88—

Example of Group Blocking registration

To use this function, station No. 200 programming (No.470 programming or No.740 programming) of the allocated station number, group, paging zone, etc., must be set up in the exchange.

1. Example of conversation and paging

To make this example of Group Blocking available for the system, the following programming at steps 2 through 4 must be set up in each exchange.

Paging to Zone No. 31

2. "No. 200 programming" in Exchange A

Function registration (A)

Function registration (B)

 

Station for

Group No. of calling

Group No. of station

 

station

All-call

each group

 

receiving call

First station No. Last station No.

 

 

2 0 1

2 0 9

 

 

2 1 0

2 1 9

 

 

2 2 0

2 4 9

 

 

2 5 0

2 7 9

 

 

Tie-line links

Tie-line links

Tie-line

Paging to Zone No. 16

Function registration (C)

Paging zone of station receiving call

Zone No.

Station not in group

 

 

 

 

 

 

 

Exchange A

ExchangeB

Exchange C

3. "No.470 programming" in Exchange B

 

 

 

Function registration (A)

Function registration (B)

 

Function registration (C)

 

Station for

Group No. of calling

Group No. of station

Paging zone of station receiving call

station

 

 

 

each group

receiving call

All-call

Zone No.

 

 

 

First station No. Last station No.

 

 

 

 

4 7 0

4 7 9

 

 

 

 

4 8 0

4 8 9

 

 

 

 

4 9 0

4 9 9

 

 

 

 

Tie-line links

 

 

 

 

 

Tie-line links

 

 

 

 

 

Station not in group

 

 

 

 

Stations capable of being called without registration.

Exchange A

Exchange B

Exchange C

Stations not belonging to the group.

 

 

 

 

Tie-line links

 

 

 

 

 

Tie-line links

 

 

 

 

 

Station not in group

 

 

 

 

 

 

 

Exchange A

Exchange B

Exchange C

4. "No. 740 programming" in Exchange C

 

 

 

Function registration (A)

Function registration (B)

 

Function registration (C)

 

Station for

Group No. of calling

Group No. of station

Paging zone of station receiving call

each group

station

receiving call

All-call

Zone No.

 

First station No. Last station No.

 

 

 

 

7 4 0

7 5 9

 

 

 

 

7 6 0

7 6 9

 

 

 

 

7 7 0

7 9 9

 

 

 

 

Note.

—89—

Programmable Restricted Access for Stations

Tie-line

Stations at which the following 7 specified functions

 

can be restricted.

 

1. All-call paging

 

2. Zone paging

 

3. Conference

 

Station number

4.General purpose control

Mode 1 (One-shot make output)

00~49 000 ~ 499

5.General purpose control Mode 2 (Make/break output)

00~99 000 ~ 511

00~99

000~511

6. General purpose control

 

Mode 3 (8 selectable one-shot make output)

1 ~ 9

1 ~ 8

Unit No.

Condition No.

General purpose control

Mode 4 (8 selectable output or decimal output)

01 ~ 64

1~8,0 (clear)

(01 ~99)

(0~9)

Unit No.

Condition No.

7. General purpose control

Mode 5 (4 decimal digits output)

1 ~ 9

0000 ~ 9999

(Unit No.)

(4-digits)

1.For conference, only the specified stations (one or more) can make a call, but any station can be called.

2.No.200 programming must be established for the specified stations.

—90—

Selectable Calling Tone

Tie-line

The duration of the calling tone can be set for either 0.2 second (single note tone) or 0.3 second (warble tone).

It is also possible to have the station without any calling tone.

Note.

1.The duration of the continuous calling tone is impossible to change.

2.It is impossible to use different calling tone modes in one same system.

Selectable Paging Pre-paging Tone Duration

Paging pre-paging tone can be chosen from "2 seconds", "1 second" and nothing.

Time-Out of Conversation

It is possible to limit the conversation duration to one through ninty-nine minutes in the unit of one minute in order to improve speech path availability. A hurry-up tone is sounded in both the calling and called stations approximately 10 seconds before the busy stations are automatically disconnected from the speech path.

Time-Out of Paging Call

This function is employed to prevent the unnecessary line occupation as a result of a paging party's failure to depress the key after a paging call establishment. The paging call is automatically cancelled after a certain period of time, which may be set at one through nintynine minutes in the unit of one minute, with a hurry-up tone transmitted to the paging station approximately 10 seconds prior to the automatic disconnection. When the paged party responds, the conversation is automatically cut off after the duration set by the Time-out of conversation function.

—91—

In/Out Annunciation

The in/out annunciation indicators can be turned on or off from any master station by using the personal number registering procedure.

When a personal number registration is made at a station, by dialing

Confirmation tone

1000~1999 (personal number)

the personal number is registered at that station and the personal number lamp on the in/out indication panel is turned on.

Personal number call

By dialing

1000~1999 (personal number)

from any station, the call is put through to the station registered with the personal number.

Cancelling personal number and turning off in/out annunciation.

By dialing

Confirmation tone

1000~1999 (personal number) from any station, the personal number is cancelled and

the personal number lamp on the in/out indication panel is turned off.

1.The maximum number of in/out annunciation windows is1000.

This maximum number remains the same even when the number of exchanges to be connected is increased to 2 or 3.

2.Produce the indication panel using the Data Transmitting and Receiving Units. For further details, refer to "Installation Hand Book for CP Unite and Operating Instructions for the DT-E70 and DR-B61".

Tie-line

In/out indication panel

Lamp on

Personal number

In/out indication panel

Lamp off

Personal number

—92—

Calling Party Indication (Lamp Type)

A one station/one lamp type calling party indication panel can be provided for certain specified stations (eight stations or eight groups of stations)

The system can also be divided into a maximum of 8 groups of stations (consecutive station numbers) so that each group may have the calling party indication panels which are common within the group. The party making the call is indicated even if the call is made to any station in the group.

<Calling station memory>

It is also possible to equip the system with the "Calling station Memory" function. With this function the calling party's lamp remains lit on the indication panel to keep on lighting even if he cancels the call when the called party is on another line or in Privacy mode.

< Indication mode without calling station memory >

1.A lamp of the calling station comes on and goes out when the conversation is over.

2.When the call is made during conversation or privacy mode, a lamp of the calling station comes on and goes out when the calling station cancels the call.

<Indication mode with calling station memory >

1.The lamp at the station receiving the call comes on when a call is made and goes out when the conversation is completed.

2.When a call (camp-on-busy) is made to the busy or the privacy station (with the privacy switch on), the lamp of calling station comes on. The lamp will not

 

go out even if the original call is cancelled.

3.

The lamp goes out after the conversation is canelled.

4.

Dialing

without placing a call causes all lights to go out. *1

Note.

*1. In the case of Handset Master station TL-600M, lift a station handset and confirm that a dial tone

is heard. Press

after cancelling the dial tone

by pressing

1.The maximum number of calling stations is 256. When 2 or 3 exchanges are connected by tie-lines, the party who is calling through the remote extension exchange is not indicated.

2.The indication panel must be used with the Data Transmitting and Receiving Units.

3.No.200 programming must be established in exchange "A" for stations or station groups to have the indication panel. Similarly, No.470 programming must be established in exchange "B" and No.740 programming in exchange "C".

4.If the lamp type calling party indication function is used, this makes it impossible to use the lamp type conversation partner indication function.

Tie-line

Indication panel at station No. 239

No.208

Camp-on-busy

No.201

Conversation

No.239

having the panel

Example of registration

Indication

First station

Last station

panel

number

number

1

 

 

2

239

239

3

 

 

4

 

 

5

251

255

6

 

 

7

 

 

8

 

 

1.Station No. 239 has the indication panel No.2.

2.The group of stations No. 251-255 is provided with the indication panel No. 5.

—93—

< Response to indicated calling party >

 

 

If,

during

the

conversation,

the called

party

wishes

to

respond

the

calling party

indicated

on the

panel,

he can do so by pressing either

1. (calling party's No.) (the conversation is terminated), or

2

(calling party's No.) (the conversation

 

is placed on hold temporarily).

Conversation Partner Indication (Lamp Type)

A one station/one lamp type Conversation Partner indication panel can be provided for specific stations (eight stations or eight groups of stations). The system can be divided into max. 8 groups of stations (consecutive station numbers) so that each group may have the Conversation Partner Indication panels which are common within the group. The party making the call and the party receiving the call are indicated whenever the calls are made to and made from any station in the group.

1.When a station having the Indication Panel makes a call, a lamp of the called station lights on until the

conversation is cancelled.

2. When a station having the Indication Panel receives a call, a lamp of the calling station lights on until the conversation is cancel led.

Note.

The waiting station making a call to the station (Camp-on-busy, privacy on) is not displayed on the Indication Panel.

Group assignment for this function should be equal to ''Conversation Partner Indication" group assignment.

Indication panel should be used with the Data Transmitting and Receiving Units.

Tie-line

Indication panel at station No. 239

No.208

Responding to a selected

calling party

No.239

No.201

Conversation

(Station No. 201 is disconnected)

(Station No.201 is hold)

Tie-line

Indication panel at station No. 239

No.239

No.201

Conversation

—94—