TOA Electronics BG-1060, BG-1030, BG-1015, BG-1120 User Manual

275.21 Kb

OPERATING INSTRUCTIONS

MIXER POWER AMPLIFIER

BG-1015

 

BG-1030

 

BG-1060

 

BG-1120

Please follow the instructions in this manual to obtain the optimum results from this unit. We also recommend that you keep this manual handy for future reference.

IMPORTANT SAFETY INSTRUCTIONS

·Be sure to read these instructions in this section carefully before use.

·Heed all warnings and follow all instructions.

·Keep these instructions handy for reference at any time.

Do not block any of the ventilation openings. Install in accordance with the manufacturer's instructions.

Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.

Do not defeat the safety purpose of the polarized or grounding type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong is provided for your safety. When the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.

Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.

Only use the attachments or accessories specified by the manufacturer.

Use only with a cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.

Unplug this apparatus during lightning storms or when unused for long periods of time.

Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

Do not use this apparatus near water.

Clean only with a dry cloth.

SAFETY PRECAUTIONS

Be sure to read the instructions in this section carefully before use.

Make sure to observe the instructions in this manual as the conventions of safety symbols and messages regarded as very important precautions are included.

We also recommend you keep this instruction manual handy for future reference.

Safety Symbol and Message Conventions

Safety symbols and messages described below are used in this manual to prevent bodily injury and property damage which could result from mishandling. Before operating your product, read this manual first and understand the safety symbols and messages so you are thoroughly aware of the potential safety hazards.

WARNING

CAUTION

Indicates a potentially hazardous situation which, if mishandled, could result in death or serious personal injury.

Indicates a potentially hazardous situation which, if mishandled, could result in moderate or minor personal injury, and/or property damage.

WARNING

When Installing the Unit

Do not expose the unit to rain or an environment where it may be splashed by water or other liquids, as doing so may result in fire or electric shock.

Use the unit only with the voltage specified on the unit. Using a voltage higher than that which is specified may result in fire or electric shock.

Do not cut, kink, otherwise damage nor modify the power supply cord. In addition, avoid using the power cord in close proximity to heaters, and never place heavy objects -- including the unit itself -- on the power cord, as doing so may result in fire or electric shock.

2

Be sure to replace the unit's terminal cover after connection completion. Because high voltage is applied to the speaker terminals, never touch these terminals to avoid electric shock.

Avoid installing or mounting the unit in unstable locations, such as on a rickety table or a slanted surface. Doing so may result in the unit falling down, causing personal injury and/or property damage.

When the Unit is in Use

Should the following irregularity be found during use, immediately switch off the power, disconnect the power supply plug from the AC outlet and contact your nearest TOA dealer. Make no further attempt to operate the unit in this condition as this may cause fire or electric shock.

·If you detect smoke or a strange smell coming from the unit.

·If water or any metallic object gets into the unit

·If the unit falls, or the unit case breaks

·If the power supply cord is damaged (exposure of the core, disconnection, etc.)

·If it is malfunctioning (no tone sounds.)

To prevent a fire or electric shock, never open nor remove the unit case as there are high voltage components inside the unit. Refer all servicing to your nearest TOA dealer.

Do not place cups, bowls, or other containers of liquid or metallic objects on top of the unit. If they accidentally spill into the unit, this may cause a fire or electric shock.

Do not insert nor drop metallic objects or flammable materials in the ventilation slots of the unit's cover, as this may result in fire or electric shock.

CAUTION

When Installing the Unit

Never plug in nor remove the power supply plug with wet hands, as doing so may cause electric shock.

ATTENTION

When unplugging the power supply cord, be sure to grasp the power supply plug; never pull on the cord itself. Operating the unit with a damaged power supply cord may cause a fire or electric shock.

When moving the unit, be sure to remove its power supply cord from the wall outlet. Moving the unit with the power cord connected to the outlet may cause damage to the power cord, resulting in fire or electric shock. When removing the power cord, be sure to hold its plug to pull.

Avoid installing the unit in humid or dusty locations, in locations exposed to the direct sunlight, near the heaters, or in locations generating sooty smoke or steam as doing otherwise may result in fire or electric shock.

When the Unit is in Use

Do not place heavy objects on the unit as this may cause it to fall or break which may result in personal injury and/or property damage. In addition, the object itself may fall off and cause injury and/or damage.

Make sure that the volume control is set to minimum position before power is switched on. Loud noise produced at high volume when power is switched on can impair hearing.

Do not operate the unit for an extended period of time with the sound distorting. This is an indication of a malfunction, which in turn can cause heat to generate and result in a fire.

Contact your TOA dealer as to the cleaning. If dust is allowed to accumulate in the unit over a long period of time, a fire or damage to the unit may result.

If dust accumulates on the power supply plug or in the wall AC outlet, a fire may result. Clean it periodically. In addition, insert the plug in the wall outlet securely.

Switch off the power, and unplug the power supply plug from the AC outlet for safety purposes when cleaning or leaving the unit unused for 10 days or more. Doing otherwise may cause a fire or electric shock.

L'appareil ne doit pas être exposé aux éclaboussures ou écoulements et tous objets remplis de liquide, tels que vases, ne doivent pas être sur l’appareil.

3

TABLE OF CONTENTS

 

1.

GENERAL DESCRIPTION .............................................................................

5

2.

FEATURES ..........................................................................................................

5

3.

NOMENCLATURE AND FUNCTIONS

 

 

Front .........................................................................................................................

6

 

Rear ..........................................................................................................................

7

4.

INPUT CONNECTIONS ...................................................................................

8

5.

OUTPUT CONNECTIONS ..............................................................................

9

6.

PLUG-IN MODULE INPUT PORT

 

 

6.1. Module Installation ............................................................................................

9

 

6.2. Module Selector Switch Settings ......................................................................

10

7.

EQUIPMENT SETTINGS

 

 

7.1. Mute Function

 

 

7.1.1. Mute operation A ....................................................................................

10

 

7.1.2. Mute operation B ....................................................................................

11

 

7.2. TEL Input Impedance Selection .......................................................................

11

 

7.3. AUX, PROGRAM, MODULE (BGM) Output Selection .....................................

12

 

7.4. Phantom Power On/Off Setting for Microphone Input ......................................

12

 

7.5. Changing MIC and PROGRAM Input Types

 

 

7.5.1. MIC input ................................................................................................

12

 

7.5.2. Program input ........................................................................................

13

8.

INSTALLATION .................................................................................................

13

9.

RACK MOUNTING ...........................................................................................

13

10. CONTROL SETTINGS ....................................................................................

14

11. DIMENSIONAL DIAGRAM ............................................................................

14

12. BLOCK DIAGRAM ...........................................................................................

15

13. SPECIFICATIONS ............................................................................................

16

 

Accessories .............................................................................................................

16

 

Optional products ....................................................................................................

16

4

1. GENERAL DESCRIPTION

TOA's BG-1015, BG-1030, BG-1060, and BG-1120 Mixer Power Amplifiers can mix up to a total of 5 independent input signals. Power output is rated at 15 W for the BG-1015, 30 W for the BG-1030, 60 W for the BG-1060, and 120 W for the BG-1120. All units are ideal for use in sound systems requiring small power outputs.

2. FEATURES

3 balanced inputs, 1 unbalanced input, and 1 module input

Phantom-powered microphone input

Telephone paging input

Compatible with all 900 Series modules (except for mute buss functions)

Wide frequency response ranging from 50 Hz to 20 kHz

Low distortion and low noise level

Excellent output regulation

Three different speaker outputs: 4 Ω, 25 V, and 70 V

MOH (Music On-Hold) output: 1 V, 600 Ω

1W output terminal: 8 Ω

Independent bass and treble controls

Input and output terminals for connection of signal processors

Two different mute functions

Overcurrent and thermal protection circuitries

Compact and lightweight

Desktop or 19" rack mountable

5

3. NOMENCLATURE AND FUNCTIONS

[Front]

5

6

7

8

9

3

4

 

MIC

 

TEL

PROGRAM

 

AUX

 

MODULE

 

 

 

 

 

 

 

 

 

 

 

SIGNAL

PEAK

POWER

0

10

0

10

0

10

0

10

0

10

 

 

 

 

 

 

 

 

 

 

 

 

 

ON

 

 

 

 

 

 

 

 

 

 

 

OFF

2

1

INTEGRATED AMPLIFIER BG-1120

1.Power switch

Press to turn ON the power. Press again to turn the power OFF.

Note

Amplifier operation is enabled about 3 seconds after the power switch is pressed.

2.Power indicator

Lights green when the power is switched on.

3.Signal level indicator

Lights green when the speaker output signal level exceeds 20 dB.

4.Peak indicator

Lights when the output signal level exceeds the point at which the signal begins to distort. If this indicator remains lit, reduce the volume at each volume control so that the indicator only lights momentarily.

Protection function to be noted on operation

This figure represents the BG-1120.

5.Microphone input volume control

Adjusts the microphone input volume. Turn clockwise to increase and counterclockwise to decrease.

6.Telephone paging input volume control

Adjusts the telephone paging input volume. Turn clockwise to increase and counterclockwise to decrease.

7.Program input volume control

Adjusts the Program input volume. Turn clockwise to increase and counterclockwise to decrease.

8.AUX input volume control

Adjusts the AUX input volume. Turn clockwise to increase and counterclockwise to decrease.

9.Module input volume control

Adjusts the Module input volume. Turn clockwise to increase and counterclockwise to decrease.

When the temperature of unit's internal heat sink exceeds the specified limit, the protection circuit is activated and the output is disconnected from the circuit. Output is automatically restored when the heat sink cools down below the temperature limit.

6

[Rear]

 

 

13

 

14

 

15

 

17

19

 

22

23

24

 

 

 

 

 

 

 

 

 

 

18

 

 

 

Blank panel

120V

60Hz

 

 

 

 

 

SENSE

 

 

 

 

 

 

 

 

MAX 500W

UNIT

 

 

 

OUTLET

 

 

 

 

MUTE

MODULE

 

 

 

 

 

 

 

 

 

 

 

 

PUSH

 

 

PUSH

 

 

 

 

 

 

 

BREAKER

 

 

BREAKER

 

 

 

 

 

 

 

 

 

 

RESET

 

 

RESET

 

 

 

 

 

 

 

 

 

 

4 A

 

 

4 A

0

 

10

 

 

 

 

 

12

 

PROGRAM

 

TEL

MIC

 

 

 

 

A

 

B PAGE

BGM

 

 

G

COM HOT

G

COM

HOT G COM

HOT NC

 

 

BASS

TREBLE

AUX

 

 

 

 

 

0

0

 

 

 

UNSWITCHED

 

 

 

 

 

 

 

+

+

 

 

27

11

 

 

OUTPUT 120 W

 

OUTPUT 1 W

MOH

MUTE

 

 

 

 

 

 

 

 

120V 60Hz

 

 

 

 

 

 

 

 

 

 

 

PREAMP

POWER

 

150W

 

COM

4Ω 25V

70V

8Ω

COM 600Ω COM

G

 

OUTPUT 1 W

MOH

 

OUT

IN

 

 

 

 

 

 

 

 

 

 

0

10

0

10

 

 

 

 

 

 

CLASS 2 WIRING

 

 

 

 

 

 

 

 

 

 

10

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

28

16

 

 

20

21

 

25

26

 

10.Power cord

Connect this cord to an AC outlet of 120 V AC.

11.Ground terminal

A functional ground terminal.

12.AC outlet [UNSWITCHED]

Continuously supplies up to 500 W of AC power to connected external equipment.

13.Breaker [UNIT]

Cuts off the AC power to the unit when its input current exceeds the allowable value.

Note

The yellow button in the breaker pops out to indicate that the breaker has tripped. After turning off the power and eliminating the cause of the breaker trip, press the button to reset the breaker.

14.Breaker [OUTLET]

Cuts off the AC power supply from the AC outlet if current output exceeds 4 A.

Note

The yellow button in the breaker pops out to indicate that the breaker has tripped. After turning off the power and eliminating the cause of the breaker trip, press the button to reset the breaker.

This figure represents the BG-1120.

15.Input terminal block

Used for connection of MIC, TEL and PROGRAM inputs. (Refer to p. 8.)

16.Output terminal block

Used for connection of speaker outputs, 1 W output, MOH (Music On-Hold) output, and Mute control signals. (Refer to p. 9 and p. 10.)

17.Sensitivity control

Adjusts the sensitivity of the mute circuit. Rotate clockwise to increase sensitivity, and counterclockwise to reduce sensitivity.

18.Bass control

Adjusts the bass frequency band level of speaker outputs for MODULE (BGM), PROGRAM, and AUX input signals. Rotate clockwise to increase bass output, and counterclockwise to reduce it. The center position provides flat characteristics.

19.Treble control

Adjusts the treble frequency band level of speaker outputs for MODULE (BGM), PROGRAM, and AUX input signals. Rotate clockwise to increase treble output, and counterclockwise to reduce it. The center position provides flat characteristics.

7

20.1 W output volume control

Adjusts the 1 W OUTPUT level. Rotate clockwise to increase and counterclockwise to decrease.

21.MOH output volume control

Adjusts the MOH (Music On-Hold) output signal level. Rotate clockwise to increase and counterclockwise to decrease.

22.Mute selector switch

Changes the type of mute operation. (Refer to p. 10.)

23.Module selector switch

Selects the output terminal for the module signal. Set the switch to the PAGE position when using the paging module, and to the BGM position when using the BGM module.

24.AUX input terminals (2P RCA pin jack)

An internal mixing type of jack.

Used for connection of external equipment input signals. (Refer to p. 8.)

25.Preamplifier output terminal [PREAMP OUT]

Used for connection of output signals to external signal processing equipment such as limiters and equalizers.

26.Power amplifier input terminal [POWER IN]

Used for connection of input signals from external signal processing equipment such as limiters and equalizers.

27.Module input port

Optional 900 Series modules can be installed here.

Note

For details concerning 900 Series modules, contact your nearest TOA dealer.

28.Terminal cover

Make sure that the terminal cover is reattached after speaker output terminal connection completion.

4. INPUT CONNECTIONS

[MIC input connections]

G COM HOT

MIC

H

C

E

[TEL and PROGRAM input connections]

G COM HOT

H

C Input source

E

[AUX input connections]

AUX

H

Input source

E

H

Input source

E

8

5. OUTPUT CONNECTIONS

[Output terminals]

Each amplifier has 3 speaker outputs: 4 Ω, 25 V and 70 V. Use only one of these outputs for connection. Class 2 wiring may be used.

Note: The impedance in the figure below represents the total impedance of the speaker system.

COM 4Ω 25V 70V

COM 4Ω 25V 70V

 

 

COM 4Ω 25V 70V

 

 

 

 

 

 

 

 

 

 

 

5.2 Ω (BG-1120)

 

 

 

 

 

40.8 Ω (BG-1120)

 

 

 

 

 

 

 

 

 

 

 

10.4 Ω (BG-1060)

 

 

 

 

 

81.7 Ω (BG-1060)

 

 

 

 

 

 

21

(BG-1030)

 

 

 

 

 

163 Ω (BG-1030)

 

 

 

 

 

4 Ω

 

 

 

 

42

(BG-1015)

 

 

 

 

 

330 Ω (BG-1015)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

25

V line

 

 

 

 

 

70 V line

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

[MOH output connections]

[OUTPUT 1 W output connections]

The MOH output is rated at 1 V/600 Ω

The OUTPUT 1 W output is rated at 1 W/8 Ω

600Ω COM G

8Ω COM

 

E

 

 

 

 

 

 

 

 

 

 

C

 

 

 

 

8Ω

H

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

6. PLUG-IN MODULE INPUT PORT

A single port for TOA plug-in modules is located on the unit's rear panel. Any 900 Series plug-in module can be inserted into this port.

Note: Consult your nearest TOA dealer for selection of appropriate module types.

Be sure to turn off the power before performing the following operations:

6.1. Module Installation

Mixer power amplifier

Step 1. Remove the blank panel covering the module slot on the rear panel.

Step 2. Align the module board with the top and bottom guide rails, and press in.

Step 3. Using the screws supplied with the module, secure the module to the rear panel.

Guide rail

900 Series plug-in module

Module mounting screw (supplied with the module)

9

6.2. Module Selector Switch Settings

Set the rear panel-mounted Module Selector Switch to either the PAGE or BGM position, depending on the output terminal to which the module signal is to be sent.

PAGE: Signals from the installed module are only sent to the

 

MODULE

speaker outputs.

PAGE

 

 

 

 

BGM

BGM: The terminal to which the signal from the module is to

 

 

 

 

 

 

 

 

 

 

 

 

be output differs depending on jumper wire settings

 

 

 

Module selector switch

inside the unit. (Refer to p. 12.)

 

 

 

 

 

 

 

 

 

Set both the bass and treble controls to the center position when using the equalizer module.

Caution: Make sure that the supplied blank panel is placed over the connector port when the port is not in use.

7. EQUIPMENT SETTINGS

Caution: Be sure to leave settings to a qualified technician.

7.1. Mute Function

The unit features 2 different mute functions, A and B. Mute A or

 

MUTE

B can be selected with the rear panel-mounted Mute Selector

A

 

 

 

 

B

Switch.

 

 

 

 

 

 

 

 

 

Mute selector switch

 

 

 

 

7.1.1. Mute operation A

The mute function can be activated either by the TEL, MIC, or MODULE (PAGE) input signal, or by shorting the rear panel-mounted mute terminals.

[Mute signal settings]

Input signals to activate the mute function can be selected by the internal jumper wire settings. The TEL, MIC, and MODULE (PAGE) input signals are all factory-preset (Jumpers JP207, JP208, and JP209 are set) as muting signals.

Cut off the jumper wire corresponding to the input signal to be disabled for muting.

In any case, shorting the rear-mounted Mute terminals can also actuate the mute function.

T203

T202 T201

Preamplifier board

Note

JP208

JP207

JP209

TEL

MIC

MOD

If Module Input is selected, the mute function can only be used when the Module Selector Switch is set to the PAGE position.

10

[Muted signal settings]

Use the unit's internal jumper switch JP301 to select the signal to be muted. Select either the input signal from the TEL, MIC, and MODULE (PAGE) terminals or from the AUX, PROGRAM, and MODULE (BGM) terminals as the signal to be muted.

Jumper switch JP301

PAGE: TEL, MIC, MODULE ( PAGE)

BGM: AUX, PROGRAM, MODULE ( BGM)

Preamplifier output board

Note: Selection is factory-preset to the input from AUX, PROGRAM,

and MODULE (BGM) terminals.

7.1.2. Mute operation B

The mute function can be controlled by way of the rear panel-mounted Mute terminal.

Note: The mute function cannot be controlled by means of an input signal.

[Mute terminal]

: Channel is ON.

: Signal is muted.

 

 

 

 

Open

 

Close

MIC

 

MIC

 

TEL

 

TEL

 

MODULE (PAGE)

 

MODULE (PAGE)

 

 

 

 

 

AUX

 

AUX

 

PROGRAM

 

PROGRAM

 

MODULE (BGM)

 

MODULE (BGM)

 

7.2. TEL Input Impedance Selection

The impedance is factory-preset to 10 kΩ. To switch to 600 Ω, change the position of the unit's internal jumper switch JP204.

600 Ω 10 kΩ

T203

T202 T201

Jumper switch JP204

Preamplifier board

11

7.3. AUX, PROGRAM, MODULE (BGM) Output Selection

Operations shown in the following table can be enabled with the unit's internal jumper settings.

[OUTPUT 15 W/30 W/60 W/120 W]

JP210

Jumpered

AUX:

ON

Cut

AUX:

OFF

 

JP211

Jumpered

PROGRAM:

ON

Cut

PROGRAM:

OFF

 

JP212

Jumpered

MODULE (BGM): ON

Cut

MODULE (BGM): OFF

 

[OUTPUT 1 W, MOH]

JP213

Jumpered

AUX:

ON

Cut

AUX:

OFF

 

JP214

Jumpered

PROGRAM:

ON

Cut

PROGRAM:

OFF

 

JP215

Jumpered

MODULE (BGM): ON

Cut

MODULE (BGM): OFF

 

[OUTPUT 1 W, MOH]

[OUTPUT 15 W/30 W/60 W/120 W]

 

JP213: AUX

JP212: MODULE (BGM)

Preamplifier board

JP214: PROGRAM

JP211: PROGRAM

 

JP215: MODULE (BGM)

JP210: AUX

 

 

T203

 

 

T202

T201

7.4. Phantom Power On/Off Setting for Microphone Input

The phantom power is set for ON or OFF by the unit's internal jumper switch JP201. It is factory-preset for OFF.

Preamplifier board

OFF ON

T203

T202 T201

Jumper switch JP201

7.5. Changing MIC and PROGRAM Input Types

Both MIC and PROGRAM inputs can be changed from electronically-balanced to transformer-balanced types in the procedures as follows.

7.5.1. MIC input

Install an optional IT-450 Line Transformer in the specified location on the printed circuit board.

Cut off the JP202 and JP203 jumper wires.

JP202

JP203

 

T203

Preamplifier board

T202

Line Transformer IT-450

12

7.5.2. Program input

Install an optional IT-453A Line Transformer in the specified location on the printed circuit board.

Cut off the JP205 and JP206 jumper wires.

JP206

T202

T201

Preamplifier board

 

 

 

JP205

Line Transformer

 

 

 

IT-453A

 

 

8. INSTALLATION

Keep the unit's all sides at least 10 cm away from objects that may obstruct air flow to prevent the unit's temperature from rising.

 

 

 

 

 

 

At least

 

 

 

 

 

 

10 cm

MIC

TEL

PROGRAM

AUX

MODULE

 

 

 

 

 

 

SIGNAL

PEAK

POWER

 

INTEGRATED AMPLIFIER BG-1120

 

 

 

 

At least

 

 

At least

10 cm

 

 

10 cm

 

 

 

 

 

 

 

 

 

 

 

 

9. RACK MOUNTING

To mount the amplifier in a standard 19" equipment rack, use the optional MB-1000 Rack Mouting Kit.

Attach the MB-1000 to the amplifier using the supplied 4 screws. When using other screws, ensure that each screw is shorter than 16 mm.

Amplifier

Amplifier

Amplifier

Amplifier

M4 x 16 Machine screw included in MB-1000

MB-1000

PF-511 Perforated Panel (1-unit size)

Note

Mount the Perforated Panel PF-511 above and below each amplifier for ventilation inside the rack.

About the perforated panel, consult your TOA dealer.

Amplifier

13

10. CONTROL SETTINGS

Output levels are adjustable with individual volume controls. For music play or announcement, adjust the corresponding volume control so that the signal indicator lights intermittently. Note that the sound quality is downgraded when the peak indicator remains lit.

To prevent the accidental change of the settings of input volume controls, remove their knobs after setting them to the desired position and attach the volume control covers instead.

 

 

 

TE

L

 

 

 

 

M

IC

 

 

 

 

 

 

 

10

 

 

 

0

 

 

10

 

 

 

0

 

 

 

-1120

 

 

 

 

 

 

 

 

BG

 

 

 

 

LIFIER

 

 

 

 

AMP

 

 

 

TED

 

IN

TE

GRA

 

 

 

 

 

 

 

 

Volume control cover (Accessory)

Volume control knob

11. DIMENSIONAL DIAGRAM (Applicable to all models)

120V

 

60Hz

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Unit: mm

MAX 500W

UNIT

 

 

 

 

 

OUTLET

 

 

 

SENSE

 

 

MUTE

 

MODULE

 

 

 

BREAKER

 

PUSH

 

 

 

BREAKER

 

PUSH

 

 

 

 

 

 

 

 

 

 

 

1.25A

 

RESET

 

 

 

4A

 

RESET

0

10

A

 

B

PAGE

BGM

 

 

 

PROGRAM

 

TEL

 

 

MIC

 

 

 

 

 

 

 

 

G

COM

HOT

G

COM

HOT

G

COM

HOT

NC

 

BASS

TREBLE

AUX

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

0

0

 

 

 

 

UNSWITCHED

 

 

 

 

 

 

 

 

 

 

+

+

 

 

 

 

 

 

 

OUTPUT 15W

 

OUTPUT 1W

 

 

MOH

MUTE

 

 

 

 

 

 

 

120V

50Hz

 

 

 

 

 

 

 

 

 

 

 

 

 

 

PREAMP

 

POWER

40W

 

COM

4Ω

25V

70V

8Ω

COM

600Ω COM

G

 

OUTPUT 1W

MOH

 

OUT

 

IN

1800

 

 

 

 

 

 

 

 

 

 

 

 

0

10

0

10

 

 

 

 

 

 

 

 

CLASS 2 WIRING

 

 

 

 

 

 

 

 

 

model BG-1015

264

 

MIC

 

TEL

PROGRAM

 

AUX

 

MODULE

 

 

 

 

 

 

 

 

 

 

 

SIGNAL

PEAK

POWER

0

10

0

10

0

10

0

10

0

10

 

 

 

 

 

 

 

 

 

 

 

 

 

ON

 

 

 

 

 

 

 

 

 

 

 

OFF

280

266.5

88.4

107.4

INTEGRATED AMPLIFIER BG-1015

14

Phantom Power (DC 24 V)

OFF JP201

ON

Option

EBA

Mic Vol.

Mic

–60 dB/600 Ω Balanced

I.T.

Tel Vol.

Tel

–20 dB/10 kΩ

I.T.

JP204

10 kΩ 600 Ω

Mute

 

Module

PAGE

OUT

 

PAGE

IN

 

BGM

Module

 

 

 

 

BGM

Option

EBA

Program Vol.

Program

–10 dB/10 kΩ

I.T.

AUX Vol.

AUX

–10 dB/47 kΩ

JP207

JP208

JP209

JP212

JP215

JP211

JP214

JP210

JP213

 

 

 

 

.12

 

 

Mute

 

BLOCK

Mute

 

 

JP301

DIAGRAM

 

 

 

 

 

 

 

A

Mute Cont.

 

PAGE

 

 

BGM

 

 

 

 

 

B

Mute Cont.

Mute selector

Tone

 

 

 

 

 

Mute

 

 

Preamp OUT

 

 

 

(Preamplifier Output)

 

 

 

 

Bass Treble

 

 

 

Power IN

 

Peak

Signal

 

(Power Amplifier Input)

 

Power

O.T.

70

 

 

 

 

 

 

 

25

Output 15 W/30 W/

 

 

 

4Ω

60 W/120 W

 

 

 

COM.

Output 1W Vol.

Power

 

 

 

 

 

 

 

 

 

 

 

Output 1 W 1 W/8 Ω

MOH Vol.

 

O.T.

 

 

 

 

 

MOH output

 

 

 

 

Power

 

 

 

1 V/600 Ω

 

 

 

 

P.T

Power S.W.

 

 

 

 

 

 

 

 

 

 

 

AC 120 V

 

Breaker

 

 

60 Hz

 

 

 

 

 

 

Breaker

 

 

 

 

A.C. Outlet

 

15

13. SPECIFICATIONS

Model No.

BG-1015

 

BG-1030

BG-1060

 

BG-1120

Power Source

 

 

 

120 V AC, 60 Hz

 

Rated Output

15 W

 

 

30 W

60 W

 

 

120 W

Power Consumption

 

 

 

 

 

 

 

 

 

 

 

Rated output

50 W

 

 

80 W

160 W

 

 

260 W

 

Based on UL/CSA standards

40 W

 

 

60 W

100 W

 

 

150 W

Frequency Response

 

 

 

50 – 20,000 Hz

 

Total Harmonic Distortion

 

 

 

0.05% at 1 kHz, rated output

 

Input

Mic:

–60 dB*1, 600 Ω, electrically balanced, M3 screw terminal*2

 

 

Tel:

–20 dB*1, 10 kΩ/600 Ω, balanced, M3 screw terminal*2

 

 

Program:

–10 dB*1, 10 kΩ, electrically-balanced, M3 screw terminal*2

 

 

Aux:

–10 dB*1, 47 kΩ, unbalanced, 2P RCA pin jack (internal mixing)

 

 

Module: –20 dB*1, 10 kΩ, unbalanced, card edge connector

 

 

 

Power IN: 0 dB*1, 10 kΩ, unbalance, RCA pin jack

 

 

 

Mute:

M3 screw terminal*2

 

 

 

 

 

Output

Main:

 

4 Ω, 25 and 70 V, balanced, M3 screw terminal*2

 

 

 

Sub:

 

1 W/8 Ω, unbalanced, M3 screw terminal*2

 

 

 

MOH:

 

0 dB*1, 600 Ω, balanced, M3 screw terminal*2

 

 

 

Preamp OUT: 0 dB*1, 600 Ω, unbalance, RCA pin jack

 

Output Regulation

 

 

 

Under 2 dB, no load to full load

 

S/N Ratio

Mic: 60 dB, Telephone: 75 dB, Program: 75 dB, Aux: 75 dB, Module: 75 dB

 

 

(Band Pass: 20 – 20,000 Hz, Tone Controls: Centered)

 

 

 

 

 

 

 

 

 

 

 

Tone Controls

Bass: ±10 dB at 100 Hz, Treble: ±10 dB at 10 kHz

 

 

 

Controls affect only program input, aux input and module (BGM) input

Cooling Fan Speed

 

 

 

Variable by heat sink temperature

Indicator

 

 

 

Power LED, Signal LED, Peak LED

 

Protection

 

 

Self protection, with 1 AC breaker (outside)

 

Other Feature

Automatic electronic drive limiter

 

 

 

 

 

 

 

Output disconnected for approx. 3 seconds after the unit is turned on

 

 

 

 

 

 

 

 

 

 

 

 

Finish

 

 

 

Panel: ABS resin, black

 

 

 

 

 

 

Case: Steel plate, black, paint

 

 

 

 

 

 

 

 

 

 

 

 

 

Dimensions

 

 

 

264 (w) x 107.4 (h) x 280 (d) mm

 

Weight

4.5 kg

 

 

4.8 kg

5.6 kg

 

6.4 kg

(without input module)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

*1 0 dB = 1 V

 

 

 

 

 

 

 

 

 

 

*2 Distance between barriers on the above screw terminal: 6 mm

 

 

 

 

 

Note: The design and specifications are subject to change without notice for improvement.

• Accessories

Volume control cover ...........................................

5

• Optional products

Line transformer: IT-450

Line transformer: IT-453A

133-12-819-0B