Thermador TRUE, C301, C271, S302, CM301 User Manual

...
0 (0)
Thermador TRUE, C301, C271, S302, CM301 User Manual

INSTALLATION INSTRUCTIONS

FOR THERMADOR® BUILT-IN ELECTRIC OVENS

Models:

C272 / C302 / CM302 / CJ302 / C271 / C301 / CM301

S272 / SC272 / SCD272 / S302 / SC302 / SCD302 / S301 / SC301 / SMW272 / SM272

Please read this entire instruction manual before proceeding.

IMPORTANT: Local codes vary. Installation, electrical connections, circuit breakers and grounding must comply with all applicable codes. Save these instructions for the Local Electrical Inspector's use.

INSTALLER: Please leave these Installation Instructions with this unit for the owner.

OWNER: Please retain these instructions for future reference.

WARNING: Disconnect power at the breaker before installing.

TABLE OF CONTENTS

 

STEP 1: UNPACKING ............................................................................................

2

STEP 2: CABINET PREPARATION .....................................................................

2

STEP 3: ELECTRICAL INSTALLATION .............................................................

6

STEP 4: INSTALLING THE OVEN ......................................................................

7

STEP 5: INSTALLING THE BOTTOM TRIM ....................................................

8

STEP 1: UNPACKING

Cut the bands from the carton. Carefully remove the carton, fillers and all packing material. Included with your new Thermador oven are the following:

Number of Racks Per Oven Model

 

C272/C302/CM302

6

SCD272/SCD302

6

SC272/SC302

5

S272/S302/CJ302

4

SC301/C271/C301/CM301/SMW272/SM272 3

S301

2

One 2-Piece Broiler Pan

Care & Use Manual

Installation Instructions

Bottom Trim

Installation Screws (Packet)

Quick Guide

Cookbook (C, CJ and CM models only)

Fig. 1 Oven Base Attachment

 

Remove Screws -

Shipping base skid

4 places

The bottom trim is shipped, wrapped in waxed paper, on top of the unit and should not be unpacked until the final step when the oven has been placed in the cabinet. See Fig. 6.

STEP 2: CABINET PREPARATION

The cabinet cutout dimensions for wall mounted and under the counter installations are shown in Figs. 2 and 3, respectively.

It is good practice, when oven is installed at the end of a cabinet run, adjacent to a perpendicular wall or cabinet door, to allow at least 1/4" space between the side of the oven door and the wall/door.

Wall Mounted Units —

For oven support, install 2 x 4’s extending front to back flush with the bottom and the side of the opening.

The supporting base must be well secured to the floor/ cabinet and level with the floor line.

NOTE: The conduit box for double ovens (S272, SC272, SCD272, S302, SC302, SCD302, C272, C302, CM302, CJ302, SMW272 and SM272) should be located above the unit to facilitate connecting and servicing. For single ovens (S301, SC301, C271, C301 and CM301) the conduit box may be installed either above or below the unit. If the conduit box is installed below the unit, a 2" diameter hole or space is required between the back wall and the right rear of the 2 x 4 supports. See Fig. 2

When an oven is installed, the cabinet base must be capable of supporting the oven weight as listed below:

Oven

Pounds

Kilograms

S-series Single Oven

165

75

C-series Single Oven

210

95

CM Single Oven

240

109

S-series Double Oven

330

150

C-series Double Oven

355

161

CM/CJ Double Oven

370

168

Page 2

Fig. 2- Cabinet Cutout - Wall Mounted Installation

 

 

 

FRONT VIEW

 

SIDE VIEW

 

 

 

F

 

G

 

 

 

 

Preferred

 

 

 

 

Location

 

C

of Conduit

 

Box

Frame

Overlap

 

 

 

 

 

 

 

 

(Top) 3/8"

 

 

 

(1, 0 cm)

 

 

 

 

Cabinet

 

 

 

 

 

 

 

 

 

 

 

 

 

 

A

 

 

 

 

 

 

 

E

 

Recommended

 

 

 

 

 

 

 

 

2" Diameter Hole (4.5 cm)

 

 

2x4

Supports

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

(Wall

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Stud)

 

 

 

 

 

 

 

 

 

 

Exposed Edge Must

 

 

 

 

 

 

 

 

 

Post Supports

 

 

 

 

 

 

 

 

 

be a Finish-Cut

 

 

 

 

 

 

 

 

 

Required Near

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Back

 

 

H

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

D

 

 

B

Side Frame Overlap

 

 

 

 

 

 

 

5/8" Cabinet

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

(1, 6 cm)

 

 

 

 

 

 

 

 

 

 

FLOOR LINE

 

 

 

 

 

Conduit Box May be Placed Here

Double Oven

Location of

Conduit Box

2-1/2" (6, 4 cm) Above

Unit

CONDUIT BOX IS NOT FURNISHED WITH UNIT

Approx. 5" (13 cm)

Refer to dimensions for specific ovens on Page 4

Page 3

Loading...
+ 5 hidden pages