Loading...
THOMSON TG784
Wireless VoIP Multi-User Ethernet WAN & ADSL2+ Gateway
Setup and User Guide
THOMSON TG784
Setup and User Guide
Copyright
Copyright ©1999-2008 Thomson. All rights reserved.
Distribution and copying of this document, use and communication of its contents is not permitted without written authorization from Thomson. The content of this document is furnished for informational use only, may be subject to change without notice, and should not be construed as a commitment by Thomson. Thomson assumes no responsibility or liability for any errors or inaccuracies that may appear in this document.
Thomson Telecom Belgium
Prins Boudewijnlaan, 47
B-2650 Edegem
Belgium
http://www.thomson-broadband.com
Trademarks
The following trademarks may be used in this document:
DECT is a trademark of ETSI.
Bluetooth® word mark and logos are owned by the Bluetooth SIG, Inc.
Ethernet™ is a trademark of Xerox Corporation.
Wi-Fi®, WMM® and the Wi-Fi logo are registered trademarks of the Wi-Fi Alliance®. "Wi-Fi CERTIFIED", "Wi-Fi ZONE", "Wi-Fi Protected Access", "Wi-Fi Multimedia", "Wi-Fi Protected Setup", WPA", WPA2" and their respective logos are trademarks of the Wi-Fi Alliance®.
UPnP™ is a certification mark of the UPnP™ Implementers Corporation.
Microsoft®, MS-DOS®, Windows®, Windows NT® and Windows Vista® are either registered trademarks or trademarks of Microsoft Corporation in the United States and/or other countries.
Apple® and Mac OS® are registered trademarks of Apple Computer, Incorporated, registered in the United States and other countries.
UNIX® is a registered trademark of UNIX System Laboratories, Incorporated.
Adobe®, the Adobe logo, Acrobat and Acrobat Reader are trademarks or registered trademarks of Adobe Systems, Incorporated, registered in the United States and/or other countries.
Other brands and product names may be trademarks or registered trademarks of their respective holders.
Document Information
Status: v1.0 (September 2008)
Reference: E-DOC-CTC-20080421-0010
Short Title: Setup and User Guide TG784 R8.2 (en)
Contents
|
About this Setup and User Guide............................................. |
1 |
1 |
Installation.................................................................................... |
3 |
1.1 |
Preliminary Steps............................................................................................ |
4 |
1.2 |
Installing your Thomson Gateway .................................................................. |
5 |
1.2.1 |
Guided Installation ................................................................................................................................. |
6 |
1.2.2 |
Manual Installation................................................................................................................................. |
8 |
2 |
Thomson Gateway Basics .......................................................... |
9 |
2.1 |
Thomson Gateway LED Behaviour ................................................................ |
10 |
2.1.1 |
Status LEDs ........................................................................................................................................... |
11 |
2.1.2 |
WPS Button LED ................................................................................................................................... |
13 |
2.1.3 |
Ethernet LEDs ....................................................................................................................................... |
14 |
2.2 |
Thomson Gateway Web Interface ................................................................. |
15 |
2.3 |
Backing Up/Restoring your Configuration .................................................... |
18 |
3 Adding a New Computer to your Network............................. |
19 |
|
3.1 |
Connecting a Computer Using the Ethernet Cable ....................................... |
20 |
4 |
Wireless ...................................................................................... |
21 |
4.1 |
Connecting Your Wireless Client via WPS .................................................... |
22 |
4.2 |
Connecting Your Wireless Client without WPS ............................................ |
24 |
4.3 |
Securing Your Wireless Connection.............................................................. |
25 |
4.3.1 |
Configuring WPA-PSK Encryption ...................................................................................................... |
27 |
4.3.2 |
Configuring WEP Encryption............................................................................................................... |
28 |
5 |
Telephony................................................................................... |
29 |
5.1 |
Connecting a Regular Phone to Your Thomson Gateway ............................. |
30 |
5.2 |
Installing the Thomson DECT USB Adapter .................................................. |
31 |
5.3 |
Connecting a DECT Phone to Your Thomson Gateway ................................ |
32 |
5.4 |
Configuring the Telephony Service............................................................... |
33 |
5.5 |
Address Book ................................................................................................ |
35 |
5.6 |
Telephony services........................................................................................ |
36 |
E-DOC-CTC-20080421-0010 v1.0
i
Contents
5.7 |
Viewing Telephony Statistics ....................................................................... |
40 |
6 Getting the Most Out of Your Thomson Gateway................. |
41 |
|
6.1 Sharing Content on your Network ................................................................ |
42 |
|
6.1.1 |
Setting Up the File Server.................................................................................................................... |
44 |
6.1.2 Managing your Shared Content.......................................................................................................... |
47 |
|
6.1.3 |
Using UPnP AV to Share Content with Media Devices ..................................................................... |
48 |
6.1.4 |
Accessing your Shared Content by FTP ............................................................................................. |
49 |
6.1.5 Safely Removing your USB Storage Device ...................................................................................... |
51 |
|
6.2 Universal Plug and Play ................................................................................ |
52 |
|
6.2.1 Accessing Your Thomson Gateway with UPnP ................................................................................. |
53 |
|
6.2.2 Managing your Internet connection with UPnP................................................................................. |
54 |
|
6.2.3 Configuring UPnP on the Thomson Gateway.................................................................................... |
56 |
|
6.2.4 Installing UPnP on Windows XP ......................................................................................................... |
57 |
|
6.3 |
Assigning a service (HTTP, FTP,...) to a computer ........................................ |
59 |
6.4 |
Dynamic DNS ................................................................................................ |
61 |
7 |
Internet Security........................................................................ |
63 |
7.1 |
Firewall.......................................................................................................... |
64 |
7.2 |
Web Site Filtering.......................................................................................... |
65 |
7.2.1 Configuring The Content-based Filter ................................................................................................ |
67 |
|
7.2.2 Adding Rules For The Address Based Filter....................................................................................... |
68 |
|
8 |
Troubleshooting ........................................................................ |
71 |
8.1 |
Setup wizard Troubleshooting ...................................................................... |
72 |
8.2 |
General Thomson Gateway Troubleshooting ................................................ |
73 |
8.2.1 |
Wired Connection Troubleshooting.................................................................................................... |
74 |
8.2.2 |
Wireless Connection Troubleshooting ............................................................................................... |
75 |
8.3 |
Voice over IP Troubleshooting...................................................................... |
76 |
8.4 |
Reset to Factory Defaults ............................................................................. |
77 |
ii
E-DOC-CTC-20080421-0010 v1.0
About this Setup and User Guide
About this Setup and User Guide
Used Symbols
A note provides additional information about a topic.
A caution warns you about potential problems or specific precautions that need to be taken.
Terminology
Generally, the THOMSON TG784 will be referred to as Thomson Gateway in this Setup and User Guide.
Typographical Conventions
Following typographical convention is used throughout this manual:
Sample text indicates a hyperlink to a Web site.
Example: For more information, visit us at www.thomson-broadband.com.
Sample text indicates an internal cross-reference.
Example: If you want to know more about guide, see “1 Introduction” on page 7”.
Sample text indicates an important content-related word.
Example: To enter the network, you must authenticate yourself.
Sample text indicates a GUI element (commands on menus and buttons, dialog box elements, file names, paths and folders).
Example: On the File menu, click Open to open a file.
Documentation and software updates
Thomson continuously develops new solutions, but is also committed to improving its existing products.
For more information on Thomson's latest technological innovations, documents and software releases, visit us at http://www.thomson-broadband.com.
E-DOC-CTC-20080421-0010 v1.0 |
1 |
|
About this Setup and User Guide
2 |
E-DOC-CTC-20080421-0010 v1.0 |
|
1 Installation
1 Installation
Introduction
In a few minutes you will be able to access the Internet using your Thomson Gateway.
This Setup and User Guide will show you how to set up your Thomson Gateway and how to connect your computer(s) to the Internet.
E-DOC-CTC-20080421-0010 v1.0 |
3 |
|
1 Installation
1.1Preliminary Steps
DSL service (only if you are using your Thomson Gateway as Internet Gateway)
The DSL service must be up and running on your telephone line.
If both conventional telephone and DSL service are simultaneously available from the same copper pair, you will need a central splitter or distributed filters for decoupling DSL and telephone signals.
Public telephone lines carry voltages that can cause electric shock. Only try to set up splitter/ filters that have been designed to be installed by unqualified personnel. For further assistance, contact your Internet Service Provider.
Computer requirements
To connect a computer via Ethernet, make sure the computer is equipped with an Ethernet Network Interface Card (NIC).
For wireless networking, you will need a WiFi-certified wireless client adapter for each computer you want to connect wirelessly.
Internet connection details
You may need the following connection details from your Internet Service Provider (ISP):
Your ISP’s method for connecting to the Internet (for example PPPoE)
The VPI/VCI (for example 8/35)
Your user name and password to connect to the Internet for PPP connections
Your IP settings in case of static configurations
Optionally your ISP may indicate the Service Profile to use during Setup.
You may have received this information when you subscribed at your Internet Service Provider. You may be prompted for this information at a given step in the installation procedure.
Voice over IP (VoIP) connection details
If you want to be able to make phone calls over the Internet, you will need following details for your VoIP connection:
A user account at your VoIP Service Provider
The server settings of your VoIP Service
These settings may be provided by your Internet Service Provider.
4 |
E-DOC-CTC-20080421-0010 v1.0 |
|
1 Installation
1.2Installing your Thomson Gateway
Installation methods
There two ways to set up your Thomson Gateway:
Guided Installation
Manual Installation
Guided Installation
How it works
The Setup wizard included on the CD will guide you through all configuration aspects of your Thomson Gateway. This is the recommended way to install your Thomson Gateway.
Requirements
Your computer must run one of the following operating systems:
Microsoft Windows Vista (SP1) or higher
Microsoft Windows Vista x64 (SP1) or higher
Microsoft Windows XP SP2 or higher
Microsoft Windows XP x64 SP 1 or higher
Microsoft Windows 2000 SP4
Mac OS X 10.4 (Tiger)
Mac OS X 10.5 (Leopard)
You must have administrative rights on your computer
Getting started
Proceed with“1.2.1 Guided Installation” on page 6.
Manual Installation
How it works
The Setup and User Guide will first help you to connect your computer to the Thomson Gateway. After this is done, you can configure your Thomson Gateway using your web browser.
Requirements
Javascript must be enabled on your web browser.
Getting started
Proceed with“1.2.2 Manual Installation” on page 8.
E-DOC-CTC-20080421-0010 v1.0 |
5 |
|
1 Installation
1.2.1Guided Installation
Connecting devices: wait!
Do not plug in any cables or connect any devices until you are prompted to do so by the wizard.
In case of problems
If you encounter problems during this installation please refer to “8.1 Setup wizard Troubleshooting” on page 72.
Starting the wizard
To start the wizard:
1Insert the Setup CD into your computer's CDor DVD-ROM drive.
2If your computer runs:
Microsoft Windows: The CD should autostart.
Mac OS X: Double-click Menu in the window with the content of the CD.
3Select the language of your choice and click OK.
4The Setup wizard will now guide you through the installation.
5At the end of the installation, following screen appears:
6Select the Go to the Thomson Gateway Web Interface if you want to go to the Thomson Gateway Web Interface after closing the wizard. On the Thomson Gateway Web Interface, you can further configure your Thomson Gateway.
7Click Finish.
8The CD menu appears.
6 |
E-DOC-CTC-20080421-0010 v1.0 |
|
1 Installation
CD menu
On the CD Menu, click:
Initial Setup to connect your computer to the Thomson Gateway and configure it.
Reconfigure my Thomson Gateway to reconfigure your Thomson Gateway.
Setup my computer to connect your computer to the Thomson Gateway network.
View Documentation to view the documentation that is available for your Thomson Gateway. This list will be automatically updated if you are connected to the Internet.
Visit Thomson Broadband to visit the online support sections on www.thomson-broadband.com.
Actual available items may depend on the Setup CD delivered with your Thomson Gateway.
E-DOC-CTC-20080421-0010 v1.0 |
7 |
|
1 Installation
1.2.2Manual Installation
Procedure
Proceed as follows:
1Connect the cables
2Configure the Thomson Gateway
Connect the cables
Proceed as follows:
1Connect your computer to the Thomson Gateway as described in “3 Adding a New Computer to your Network” on page 19.
2Connect the Thomson Gateway to the DSL line.
If your Internet Service Provider (ISP) is not using the Thomson Gateway to access the Internet, you must not connect the DSL cable. Instead, use an Ethernet cable to connect the WAN port of your Thomson Gateway to your Internet Gateway.
3Connect the power supply.
4Turn on the Thomson Gateway.
Configure the Thomson Gateway
1Open your web browser.
2The Thomson Gateway informs you that you have not yet configured your Thomson Gateway.
If this window does not appear browse to http://dsldevice.lan or to the IP address of your Thomson Gateway (by default: 192.168.1.254) and click Thomson Gateway on the menu on the left-hand side.
3Click Setup my Thomson Gateway.
4The Easy Setup wizard appears. This wizard will guide you through the configuration of your Thomson Gateway. Click Next and follow the instructions.
8 |
E-DOC-CTC-20080421-0010 v1.0 |
|
|
|
2 Thomson Gateway Basics |
||
|
|
|
|
|
2 Thomson Gateway Basics |
|
|
|
|
In this chapter |
|
|
|
|
|
|
|
|
|
|
Topic |
|
Page |
|
|
|
|
|
|
|
Thomson Gateway LED Behaviour |
|
10 |
|
|
|
|
|
|
|
Thomson Gateway Web Interface |
|
15 |
|
|
|
|
|
|
|
Backing Up/Restoring your Configuration |
|
18 |
|
|
|
|
|
|
E-DOC-CTC-20080421-0010 v1.0 |
9 |
|
2 Thomson Gateway Basics
2.1Thomson Gateway LED Behaviour
Content
This chapter describes the behaviour of:
Status LEDs
WPS Button LED
Ethernet LEDs
10 |
E-DOC-CTC-20080421-0010 v1.0 |
|
2 Thomson Gateway Basics
2.1.1Status LEDs
Introduction
On the top panel of your Thomson Gateway, you can find a number of status LEDs, indicating the state of the device during normal operation.
Power LED
Colour |
State |
Description |
|
|
|
Green |
Solid on |
Power on, normal operation |
|
|
|
Red |
Solid on |
Power on, self-test failed, indicating device malfunction |
|
|
|
Amber |
Blinking |
Bootloader active (during upgrade) |
|
|
|
Off |
|
Power off |
|
|
|
Ethernet LED
|
Colour |
State |
Description |
|
|
|
|
|
Green |
Blinking |
Ethernet activity |
|
|
|
|
|
|
Solid on |
Ethernet connection, no activity |
|
|
|
|
|
Off |
|
No Ethernet connection |
|
|
|
|
Wireless LED |
|
|
|
Colour |
State |
Description |
|
|
|
Green |
Blinking |
Wireless activity, WPA(2) encryption |
|
|
|
|
Solid on |
No wireless activity, WPA(2) encryption |
|
|
|
Amber |
Blinking |
Wireless activity, WEP encryption |
|
|
|
|
Solid on |
No wireless activity, WEP encryption |
|
|
|
Red |
Blinking |
Wireless activity, no security |
|
|
|
|
Solid on |
No wireless activity, no security |
|
|
|
Red/green |
Toggling |
Wireless client registration phase |
|
|
|
Off |
|
WLAN disabled |
|
|
|
E-DOC-CTC-20080421-0010 v1.0 |
11 |
|
2 Thomson Gateway Basics
Broadband LED
|
Colour |
State |
Description |
|
|
|
|
|
Green |
Blinking |
Pending DSL line synchronisation |
|
|
|
|
|
|
Solid on |
DSL line synchronised |
|
|
|
|
|
Off |
|
No DSL line |
|
|
|
|
Internet LED |
|
|
|
|
Colour |
State |
Description |
|
|
|
|
|
Green |
Blinking |
Internet activity |
|
|
|
|
|
|
Solid on |
Internet connectivity, no activity |
|
|
|
|
|
Red |
Solid on |
Internet connection setup failed |
|
|
|
|
|
Off |
|
No Internet connection |
|
|
|
|
Phone LED |
|
|
|
Colour |
State |
Description |
|
|
|
Green |
Solid on |
VoIP service up |
|
|
|
|
Blinking |
VoIP activity |
|
|
|
Off |
|
VoIP service down |
|
|
|
12 |
E-DOC-CTC-20080421-0010 v1.0 |
|
2 Thomson Gateway Basics
2.1.2WPS Button LED
Introduction
The WPS button allows you to add new wireless clients to your network.
For more information, see Connecting Your Wireless Client via WPS.
WPS LED
Colour |
State |
Description |
|
|
|
Green |
Solid On |
Client successfully registered via WPS |
|
|
|
Amber |
Blinking |
WPS registration ongoing |
|
|
|
Red |
Blinking |
Error occurred |
|
|
|
E-DOC-CTC-20080421-0010 v1.0 |
13 |
|
2 Thomson Gateway Basics
2.1.3Ethernet LEDs
Ethernet LED
A LED may be provided per Ethernet port to indicate link integrity (or activity).
LED Status |
Description |
|
|
Off |
No connection on this port |
|
|
Solid on |
Ethernet link up |
|
|
Blinking |
Data is flowing from/to this port |
|
|
14 |
E-DOC-CTC-20080421-0010 v1.0 |
|
2 Thomson Gateway Basics
2.2Thomson Gateway Web Interface
Introduction
The Thomson Gateway Web Interface allows you to configure your Thomson Gateway using your web browser.
Requirements
Javascript must be enabled on your browser. For more information, consult the help of your Internet browser.
Accessing the Thomson Gateway Web Interface
Proceed as follows:
1Open your web browser.
2Browse to http://dsldevice.lan or to the IP address of your Thomson Gateway (by default: 192.168.1.254).
3If you have protected your Thomson Gateway with a user name and password, the Thomson Gateway will prompt you to enter these. Enter your user name and password and click OK.
4The Thomson Gateway Web Interface appears.
If your computer runs Windows Vista or Windows XP, you can also access the Thomson Gateway Web Interface using the Internet Gateway Device icon. For more information, see “6.2 Universal Plug and Play” on page 52.
E-DOC-CTC-20080421-0010 v1.0 |
15 |
|
2 Thomson Gateway Basics
Components
All the pages contain following components:
2
4
3
5
1
6
7
Label Description
1Menu
2Language bar
3Location bar
4Login section
5Notification area
6Content pane
7Tasks
Menu
The menu consists of the following menu items:
Home:
Allows you to go back to the home page.
Thomson Gateway:
Provides basic information on the Thomson Gateway.
Broadband Connection:
Allows you to view/configure your broadband connections.
Toolbox:
Allows you to assign games or applications to a device and secure your Internet connection.
Home Network:
Allows you to manage your local network.
Help:
Allows you to view context-related help information.
16 |
E-DOC-CTC-20080421-0010 v1.0 |
|
2 Thomson Gateway Basics
Language bar
The language bar allows you to change the language of the Thomson Gateway Web interface.
The language bar will only be shown if more than one language is available.
Location bar
The location bar allows you to view the current position in the Thomson Gateway Web interface.
Login section
In this section you can see the current user name.
By clicking your user name, you can:
Change your password.
Switch to another user.
Notification area
The notification area is used to display:
Error messages, indicated by a red traffic light.
Warnings, indicated by an orange traffic light.
Information, indicated by a green traffic light.
If none of these events occur, the notification area will not be shown.
Content pane
The content pane displays the information and configurable items of the selected topic.
Tasks
To allow a quick configuration of your Thomson Gateway, some pages may offer you a number of related tasks in the Pick a task list. These tasks will guide you to the page where you can perform the selected task.
E-DOC-CTC-20080421-0010 v1.0 |
17 |
|
2 Thomson Gateway Basics
2.3Backing Up/Restoring your Configuration
Introduction
Once you have configured your Thomson Gateway to your needs, it may be a good idea to backup your configuration for later use. This way you can always return to your working configuration in case of problems.
Backing up your configuration
Proceed as follows:
1Browse to the Thomson Gateway Web Interface.
2On the Thomson Gateway menu, click Configuration.
3In the Pick a task list, click Save or Restore Configuration.
4Under Backup current configuration, click Backup Configuration Now.
5The Thomson Gateway prompts you to save your file.
6Save your file to a location of your choice.
Restoring your configuration
Proceed as follows:
1Browse to the Thomson Gateway Web Interface.
2On the Thomson Gateway menu, click Configuration.
3In the Pick a task list, click Save or Restore Configuration.
4Under Restore saved configuration, click Browse.
5Open your backup file.
6The Thomson Gateway restores your configuration.
18 |
E-DOC-CTC-20080421-0010 v1.0 |
|
3 Adding a New Computer to your Network
3 Adding a New Computer to your Network
Guided Installation
If you configured your Thomson Gateway using the Guided Installation, use the same procedure on the computer that you want to add.
At a specific point in the installation, the Setup wizard will inform you that the Thomson Gateway has already been configured:
Select No and click Next to continue.
Manual Installation
If you want to connect your computer to the Thomson Gateway using:
A Wireless connection, continue with “4 Wireless” on page 21.
The Ethernet cable, continue with “3.1 Connecting a Computer Using the Ethernet Cable” on page 20.
E-DOC-CTC-20080421-0010 v1.0 |
19 |
|
3 Adding a New Computer to your Network
3.1Connecting a Computer Using the Ethernet Cable
Requirements
Your computer must have a free Ethernet port.
Your computer must be configured to obtain an IP address automatically. This is the default setting.
Ethernet cable
In your package, you will find a cable with yellow connectors. This is the Ethernet cable.
Procedure
Proceed as follows:
1 Connect one end of the Ethernet cable to (one of the) yellow Ethernet port(s) of your Thomson Gateway:
2Connect the other end of the Ethernet cable to your computer.
3Your computer is now connected to your network. No additional configuration is needed.
20 |
E-DOC-CTC-20080421-0010 v1.0 |
|
Loading...