TEAC DVH-500 Service manual

1-2

SECTION 1

SUMMARY

CONTENTS

PRODUCT SAFETY SERVICING GUIDELINES FOR VIDEO PRODUCTS ............................................. 1-3

SERVICING PRECAUTIONS ....................................................................................................................... 1-4

* General Servicing Precautions
* Insulation checking prodedure
* Electrostatically Sensitive Devices

SPECIFICATIONS ......................................................................................................................................... 1-5

LOCATION OF CUSTOMER CONTROLS ......................................................................................... 1-6 ~ 1-7

1-3

PRODUCT SAFETY SER

VICING GUIDELINES FOR VIDEO PRODUCTS

CAUTION : DO NOT ATTEMPT TO MODIFY THIS PRODUCT IN
ANY WAY. NEVER PERFORM CUSTOMIZED INSTALLATIONS
WITHOUT MANUFACTURER’S APPROVAL. UNAUTHORIZED
MODIFICATIONS WILL NOT ONLY VOID THE WARRANTY, BUT
MAY LEAD TO YOUR BEING LIABLE FOR ANY RESULTING
PROPERTY DAMAGE OR USER INJURY.

SERVICE WORK SHOULD BE PERFORMED ONLY AFTER YOU
ARE THOROUGHLY FAMILIAR WITH ALL OF THE FOLLOWING
SAFETY CHECKS AND SERVICING GUIDELINES. TO DO
OTHERWISE, INCREASES THE RISK OF POTENTIAL HAZARDS
AND INJURY TO THE USER.

WHILE SERVICING, USE AN ISOLATION TRANSFORMER FOR
PROTECTION FROM A.C. LINE SHOCK.

SAFETY CHECKS

AFTER THE ORIGINAL SERVICE PROBLEM HAS BEEN
CORRCTED. A CHECK SHOULD BE MADE OF THE
FOLLOWING.

SUBJECT : FIRE & SHOCK HAZARD

1. BE SURE THAT ALL COMPONENTS ARE POSITIONED IN
SUCH A WAY AS TO AVOID POSSIBILITY OF ADJACENT
COMPONENT SHORTS. THIS IS ESPECIALLY IMPORTANT
ON THOSE MODULES WHICH ARE TRANSPORTED TO AND
FROM THE REPAIR SHOP.

2. NEVER RELEASE A REPAIR UNLESS ALL PROTECTIVE
DEVICES SUCH AS INSULATORS, BARRIERS, COVERS,
SHIELDS, STRAIN RELIEFS, POWER SUPPLY CORDS, AND
OTHER HARDWARE HAVE BEEN REINSTALLED PER
ORIGINAL DESIGN. BE SURE THAT THE SAFETY PURPOSE
OF THE POLARIZED LINE PLUG HAS NOT BEEN DEFEATED.

3. SOLDERING MUST BE INSPECTED TO DISCOVER POSSIBLE
COLD SOLDER JOINTS, SOLDER SPLASHES OR SHARP
SOLDER POINTS. BE CERTAIN TO REMOVE ALL LOOSE
FOREIGN PARTICLES.

4. CHECK FOR PHYSICAL EVIDENCE OF DAMAGE OR
DETERIORATION TO PARTS AND COMPONENTS. FOR
FRAYED LEADS, DAMAGED INSULATION (INCLUDING A.C.
CORD). AND REPLACE IF NECESSARY FOLLOW ORIGINAL
LAYOUT, LEAD LENGTH AND DRESS.

5. NO LEAD OR COMPONENT SHOULD TOUCH A RECIVING
TUBE OR A RESISTOR RATED AT 1 WATT OR MORE. LEAD
TENSION AROUND PROTRUNING METAL SURFACES MUST
BE AVOIDED.

6. ALL CRITICAL COMPONENTS SUCH AS FUSES,
FLAMEPROOF RESISTORS, CAPACITORS, ETC. MUST BE
REPLACED WITH EXACT FACTORY TYPES, DO NOT USE
REPLACEMENT COMPONENTS OTHER THAN THOSE
SPECIFIED OR MAKE UNRECOMMENDED CIRCUIT
MODIFICATIONS.

7. AFTER RE-ASSEMBLY OF THE SET ALWAYS PERFORM AN
A.C.LEAKAGE TEST ON ALL EXPOSED METALLIC PARTS OF
THE CABINET, (THE CHANNEL SELECTOR KNOB, ANTENNA
TERMINALS. HANDLE AND SCREWS) TO BE SURE THE SET
IS SAFET TO OPERATE WITHOUT DANGER OF ELECTRICAL
SHOCK. DO NOT USE A LINE ISOLATION TRANSFORMER
DURING THIS TEST USE AN A.C. VOLTMETER, HAVING 5000
OHMS PER VOLT OR MORE SENSITIVITY, IN THE
FOLLOWING MANNER; CONNECT A 1500 OHM 10 WATT
RESISTOR, PARALLELED BY A .15 MFD, 150.V A.C TYPE
CAPACITOR BETWEEN A KNOWN GOOD EARTH GROUND
(WATER PIPE, CONDUIT, ETC.) AND THE EXPOSED
METALLIC PARTS, ONE AT A TIME.
MEASURE THE A.C. VOLTAGE ACROSS THE COMBINATION
OF 1500 OHM RESISTOR AND .15 MFD CAPACITOR.
REVERSE THE A.C. PLUG AND REPEAT A.C. VOLTAGE
MEASUREMENTS FOR EACH EXPOSED METALLIC PART.

VOLTAGE MEASURE MUST NOT EXCEED 75 VOLTS R.M.S.
THIS CORRESPONDS TO 0.5 MILLIAMP A.C ANY VALUE
EXCEEDING THIS LIMIT CONSTITUTES A POTENTIAL
SHOCK HAZARD AND MUST BE CORRECTED IMMEDIATELY.

SUBJECT : GRAPHIC SYMBOLS

SUBJECT : TIPS ON PROPER INST ALLATION

1. NEVER INSTALL ANY PRODUCT IN A CLOSED-IN RECESS,
CUBBYHOLE OR CLOSELY FITTING SHELF SPACE. OVER
OR CLOSE TO HEAT DUCT, OR IN THE PATH OF HEATED
AIR FLOW.

2. AVOID CONDITIONS OF HIGH HUMIDITY SUCH AS:
OUTDOOR PATIO INSTALLATIONS WHERE DEW IS A
FACTOR, NEAR STEAM RADIATORS WHERE STEAM
LEAKAGE IS A FACTOR, ETC.

3. AVOID PALCEMENT WHERE DRAPERIES MAY OBSTRUCT
REAR VENTING. THE CUSTOMER SHOULD ALSO AVOID THE
USE OF DECORATIVE SCARVES OR OTHER COVERINGS
WHICH MIGHT OBSTRUCT VENTILATION.

4. WALL AND SHELF MOUNTED INSTALLATIONS USING A
COMMERCAL MOUNTING KIT. MUST FOLLOW THE
FACTORY APPROVED MOUNTING INSTRUCTIONS A
PRODUCT MOUNTED TO A SHELF OR PLATFORM MUST
RETAIN ITS ORIGINAL FEET (OR THE EQUIVALENT
THICKNESS IN SPACERS) TO PROVIDE ADEQUATE AIR
FLOW ACROSS THE BOTTOM, BOLTS OR SCREWS USED
FOR FASTENERS MUST NOT TOUCH ANY PARTS OR
WIRING. PERFORM LEAKAGE TEST ON CUSTOMIZED
INSTALLATIONS.

5. CAUTION CUSTOMERS AGAINST THE MOUNTING OF A
PRODUCT ON SLOPING SHELF OR A TILTED POSITION,
UNLESS THE PRODUCT IS PROPERLY SECURED.

6. A PRODUCT ON A ROLL-ABOUT CART SHOULD BE STABLE
ON ITS MOUNTING TO THE CART. CAUTION THE
CUSTOMER ON THE HAZARDS OF TRYING TO ROLL A CART
WITH SMALL CASTERS ACROSS THRESHOLDS OR DEEP
PILE CARPETS.

7. CAUTION CUSTOMERS AGAINST THE USE OF A CART OR
STAND WHICH HAS NOT BEEN LISTED BY UNDERWRITERS
LABORATORIES, INC. FOR USE WITH THEIR SPECIFIC
MODEL OF TELEVISION RECEIVER OR GENERICALLY
APPROVED FOR USE WITH T.V.’S OF THE SAME OR
LARGER SCREEN SIZE.

8. CAUTION CUSTOMERS AGAINST THE USE OF EXTENSION
CORDS, EXPLAIN THAT A FOREST OF EXTENSIONS
SPROUTING FROM A SINGLE OUTLET CAN LEAD TO
DISASTROUS CONSEQUENCES TO HOME AND FAMILY.

THE LIGHTNING FLASH WITH ARROWHEAD SYMBOL, WITHIN AN
EQUILATERAL TRIANGLE, IS INTENDED TO ALERT THE USER TO THE
PRESENCE OF UNINSULATED “DANGEROUS VOLTAGE” WITHIN THE
PRODUCT’S ENCLOSURE THAT MAY BE OF SUFFICIENT MAGNITUDE TO
CONSTITUTE A RISK OF ELECTRIC SHOCK.

THE EXCLAMATION POINT WITHIN AN EQUILATERAL TRIANGLE IS
INTENDED TO ALERT THE USER TO THE PRESENCE OF IMPORTANT
OPERATING AND MAINTENANCE (SERVICING) INSTRUCTIONS IN THE
LITERATURE ACCOMPANYING THE APPLIANCE.

A.C. VOLTMETER

PLACE THIS PROBE
ON EACH EXPOSED
METAL PART

GOOD EARTH GROUND
SUCH AS THE WATER
PIPE. CONDUIT. ETC

10 WATT

0.15uF

1-4

SER

VICING PRECAUTIONS

CAUTION : Before servicing the DVD player covered by this service
data and its supplements and addends, read and follow the SAFETY
PRECAUTIONS. NOTE : if unforeseen circumstances create conflict
between the following servicing precautions and any of the safety
precautions in this publications, always follow the safety precautions.

Remembers Safety First:

General Servicing Precautions

1. Always unplug the DVD player AC power cord from the AC power
source before:
(1) Removing or reinstalling any component, circuit board,

module, or any other assembly.

(2) Disconnection or reconnecting any internal electrical plug or

other electrical connection.

(3) Connecting a test substitute in parallel with an electrolytic

capacitor.
Caution : A wrong part substitution or incorrect polarity installation
of electrolytic capacitors may result in an explosion hazard.

2. Do not spray chemicals on or near this DVD player or any of its
assemblies.

3. Unless specified otherwise in this service data, clean electrical
contacts by applying an appropriate contact cleaning solution to
the contacts with a pipe cleaner, cottontipped swab, or
comparable soft applicator.
Unless specified otherwise in this service data, lubrication of
contacts is not required.

4. Do not defeat any plug/socket B+ voltage interlocks with whitch
instruments covered by this service manual might be equipped.

5. Do not apply AC power to this DVD player and/or any of its
electrical assemblies unless all solid-state device heat sinks are
cerrectly installed.

6. Always connect test instrument ground lead to the appropriate
ground before connection the test instrument positive lead. Always
remove the test instrument ground lead last.

Insulation Checking Procedure

Disconnect the attachment plug from the AC outlet and turn the
power on. Connect an insulation resistance meter(500V) to the
blades of the attachment plug. The insulation resistance between
each blade of the attachment plug and accessible conductive parts
(Note 1) should be more than 1M-ohm.
Note 1 : Accessible Conductive Parts including Metal panels, Input
terminals, Earphone jacks, etc.

Electrostatically Sensitive (ES) Devices

Some semiconductor (solid state) devices can be damaged easily by
static electricity. Such components commonly are called
Electrostatically Sensitive (ES) Devices. Examples of typical Es
devices are integrated circuits and some field effect transistors and
semiconductor chip components.
The following techniques should be used to help reduce the
incidence of component damage caused by static electricity.

1. Immediately before handling any semiconductor component or
semiconductorequipped assembly, drain off any electrostatic
charge on your body by touching a known earth ground.
Alternatively, obtain and wear a commercially available
discharging wrist strap device, which should be removed for
potential shock reasons prior to applying power to the unit under
test.

2. After removing an electrical assembly equipped with ES devices,
place the assembly on a conductive surface such as aluminum
foil, to prevent electrostatic charge buildup or exposure of the
assembly.

3. Use only a grounded-tip soldering iron to solder or unsolder ES
devices.

4. Use only an antistatic solder removal device. Some solder
removal devices not classified a “anti-static” can generate
electrical charges sufficient to damage ES devices.

5. Do not use freonpropelled chemicals. These can generate
electrical charge sufficient to damage ES devices.

6. Do not remove a replacement ES device from its protec tive
package until immediately before you are ready to install it. (Most
replacement ES devices are packaged with leads electrically
shorted together by conductive foam, aluminum foil, or
comparable conductive material).

7. lmmediately before removing the protective material from the
leads of a replacement ES device, touch the protective material to
the chassis or circuit assembly into which the device will be
installed.

Caution : Be sure no power is applied to the chassis or circuit, and
observe all other safety precautions.

8. Minimize bodily motions when handing unpackaged replacement
ES devices. (Normally harmless motion such as the brushing
together of your clothes fabric or the lifting of your foot from a
carpeted floor can generate static electricity sufficient to damage
an ES device.)

1-5

SPECIFICA

TIONS

DVD VIDEO PLAYER

Power supply .............................................................. AC 230 V, 50 Hz (EUR)/ 120 V, 60 Hz (US/CANADA)

Power consumption .................................................... 22 W

External dimensions (W x H x D) ................................ 285 x 131 x 292 mm

Weight (net) ................................................................ 3.9 kg

Signal system ............................................................. PAL (EUR)/NTSC (US/CANADA)

Laser ........................................................................... Semiconductor laser, wavelength 650 nm

Frequency range (digital audio) .................................. 2 Hz to 22 kHz

Signal-to-noise rating (digital audio) ........................... More than 105 dB (EIAJ)

Audio dynamic range (digital audio) ........................... More than 92 dB (EIAJ)

Harmonic distortion (digital audio) .............................. 0.008%

Wow and flutter ........................................................... Below measurable level (less than + 0.001% (W.PEAK)) (EIAJ)

Operating conditions ................................................... Temperature: 41˚F to 95˚F, Operation status: Horizontal

OUTPUTS

Video output ............................................................... 1.0 V (p-p), 75 Ω, negative sync., RCA jack x 1

S-video output ............................................................ (Y) 1.0 V (p-p), 75 Ω, negative sync., Mini DIN 4-pin x 1

(C) 0.286 V (p-p) 75 Ω

Audio output (digital audio) ......................................... 0.5 V (p-p), 75 Ω, RCA jack x 1

Audio output (analog audio) ....................................... 2.0 Vrms (1 kHz, 0 dB), RCA jack x1

1-6

LOCA

TION OF CUSTOMER CONTROLS

POWER/Standby button
and indicator
(Standby mode : Red color)

Display Window

OPEN/CLOSE

button

SKIP/SCAN
buttons

STOP button

PLAY button

PAUSE button

Disc Tray

TruSurroundRemote sensor

Audio 5.1CH OUT jacks

POWER Cord

AUDIO MIXED OUT jacks

DIGITAL AUDIO OUT jack
(COAXIAL)

DIGITAL AUDIO OUT jack
(OPTICAL)

Remote Control Selector
switch

Remote Control jacks

AV CONNECTOR jack

S-VIDEO OUT jack

VIDEO OUT jack

FRONT P ANEL

REAR PANEL

[EUR only]

1-7

RANDOM indicator

PROGRAM indicator

CHAPTER indicator RESUME indicator

TRACK indicator REPEAT indicator

REMAIN indicatorTITLE indicatorPLAY indicator

VIDEO CD indicator

DVD indicator

5.1 CH & SRS indicator

Use the TITLE button to display the title
screen included on DVD video discs.
To operate a menu screen, follow the
instructions in "Using a Title Menu".

Use the MENU button to display the menu
screen included on DVD video discs.
To operate a menu screen, follow the
instructions in "Using a DVD Menu".

(up, down, left, right) for use in highlighting
a selection on a GUI menu screen, TITLE
and MENU screen

** Directional arrow buttons

*** TITLE button

* MENU button

POWER button

REPEAT button

SHUFFLE
(RANDOM) button

SET UP button

AUDIO button

SUBTITLE button

***TITLE button

SELECT button

GUI button

MARKER button

SCAN/STEP button

ZOOM button

RESUME button

Number button

CLEAR button

PROGRAM button

PAUSE button

STOP button

FWD/REV SKIP button
PLAY button

SLOW buttons

MARKER-SEARCH button

RETURN button

**ARROW buttons

*MENU button

ANGLE button

TruSURROUND button

A-B button

OPEN/CLOSE button

DISPLAY Window

REMOTE CONTROL

1-8

RANDOM indicator

PROGRAM indicator

CHAPTER indicator RESUME indicator

TRACK indicator REPEAT indicator

REMAIN indicatorTITLE indicatorPLAY indicator

VIDEO CD indicator

DVD indicator

5.1 CH & SRS indicator

Use the TITLE button to display the title
screen included on DVD video discs.
To operate a menu screen, follow the
instructions in "Using a Title Menu".

Use the MENU button to display the menu
screen included on DVD video discs.
To operate a menu screen, follow the
instructions in "Using a DVD Menu".

(up, down, left, right) for use in highlighting
a selection on a GUI menu screen, TITLE
and MENU screen

** Directional arrow buttons

*** TITLE button

* MENU button

POWER button

REPEAT button

SHUFFLE
(RANDOM) button

SET UP button

AUDIO button

SUBTITLE button

***TITLE button

SELECT button

GUI button

MARKER button

SCAN/STEP button

ZOOM button

RESUME button

Number button

CLEAR button

PROGRAM button

PAUSE button

STOP button

FWD/REV SKIP button
PLAY button

SLOW buttons

MARKER-SEARCH button

RETURN button

**ARROW buttons

*MENU button

ANGLE button

TruSURROUND button

A-B button

OPEN/CLOSE button

DISPLAY Window

REMOTE CONTROL

2-9

ELECTRICAL TROUBLESHOOTING GUIDE

1. SYSTEM CHECK

Standby LED ON?

Power ON.

OK

YES

NO

Refer to Front Part.

NO

NO

Replace Main B/D

Check Mechanism

Reconnect

Check Power.

Does Bar appear at FLD?

Do all eight Bars appear?

NO

YES

NO

Reconnect

NO

Check Mechanism

NO

Refer to Front Part

NO

Check the Oscillation

YES

Refer to Front Part

Check Video part

NO

Check MPEG part

Is CN04

Connected normally?

YES

YES

YES

YES

NO

Is CN04 Pin

5 7 normally?

"CHECK" message

appear?

Is CN06, CN07

Connected normally?

YES

Does logo appear?

YES YES

Disc reading?

YES

AUDIO/VIDEO output?

YES

YES

NO

Is CN04 Pin

1 3 normally?

Is oscillation of

X101 normal?

NO

Refer to Front Part

Are IC25 Pin 116

and TP54,55 normal?

YES

NO

Replace IC

Replace Main B/D

Is IC8, 9, 10, 11

normal?

2-10

2. Power Circuit

Input Voltage : 230 V
It is possible to malfunction, if the unload condition is left for a long time when power on.

(More than Dummy load 100mA)
The resistor value of both terminal is measured with DVM crossing each other to check the each element is normal or abnormal.

(It is normal when the numerical value is different each other.)

START

Is F601 normal?

YES

NO

A primary side abnormal

Check the GND of C601 and
IC68 Pin 3 with oscilloscope

END

END

To (A)

(A)

Is voltage D601 230V?

NO

NO

NO

NO

NO

NO

Is IC68 pin 3

switching normally?

YES

Are R607, D602,

normal?

YES

Are SN61 and R612

normal?

YES

Is PC61 normal?

YES

YES

Is CN63 pin 6 5.2V?

In condition of DC140V.
(Feedback is abnormal)

Check or
replace
D610,D622.

YES

YES

Is CN64 pin 3 5V?

YES

Is CN64

pin 9 and 11 12V?

YES

YES

NO

Are CN63 Pin 6

-32V, Pin 4 -22V and
Pin 5 -26V?

Is CN64

pin 1 and 2 3.3V?

YES

YES

YES

Are CN64

Pin 4 and 5 5V?

Does oscillate
continuously when the
CN63 is disconnected?

When IC68
Oscillating

Secondary side
is abnormal.

NO

NO

Is IC61
normal?

Replace defective

Parts.

Replace D616,

Q602 and Q609.

Are R618, C626,
R621 and R910
normal?

After connect
CN63
Pin 2 , 7 Short.

NO

Front Circuit
Board is
abnormal

Replace
defective
parts.

Replace IC66

NO

Check Q622

and Q617.

NO

NO

Check Q621

and Q623.

NO

Are D610, D611
D612, D614, D615
and D617 normal?

YES

Is CN63 Pin 2

5.2V?

YES

2-11

3. MPEG Circuit

Power ON

Does DVD

LOGO appear

on the screen?

Does the

moving picture of the

DVD Disc

play on the screen

normally?

YES

Does the

audio sound output normally?

Is the data from

MPEG to

DAC normally?

YES

END

YES

YES

YES

Does OSD appear

normally?

NO

Does OSD

appear normally?

NO

NO

Check VIDEO part

Check IC23

NO

Replace MAIN B/D

Check IC22 and IC23

NO

Check IC22

NO

YES

Check AUDIO part

2-12

4. FRONT Circuit (Digtron & Key)

STRAT

LED ON?

END

Power ON.

Is oscillation of

X901 normal?

YES

YES

NO

NO

Check Power.

Is Display on normally?

Check waveform
of IC91 Pin 32 .

NO

NO

NO

Replace Q902.

Replace IC91.

Solder Key part.

YES

YES

YES

YES

Do all the

buttons work

normally?

Is waveform of IC91

Pin 42 normal?

Check waveform

of IC91 Pin 51 - 54 .

NO

Replace D906.

Replace Rs91.

Replace IC91.Complete repairing Front B/D. Re-solder.

Recheck

Replace Q901 and Q903.

YES

Check waveform

of Q901 and Q902.

NO

Check and replace D901,
D902, D907, R932, R933,
R934 and R935.

Check the pattern between
IC91 and FIP1.

Solder defective parts again.

YES

Check waveform

of IC91 Pin 51 - 54 .

YES

NO

NO

NO

Solder defective part.

YES

YES

Does remote

control work

normally?

Does pulse

waveform of Rs51 Pin 1

appear?

Is Rs91 Pin 3 5V?

YES

YES

YES YES

YES

Is IC91

Pin 62 Connected to

Rs91 Pin 1 ?

NO

NO

NO

2-13

A. Audio abnormal

Check Audio Jack.

AUDIO ABNORMAL

Check the Mute TR.

Refer to Audio part.

Refer to MPEG part.

Replace B/D.

C. DISC ERROR

Check the disc.

DISC ERROR

Refer to Servo part.

Replace MAIN B/D.

B. OPEN/CLOSE abnormal E. PICTURE abnormal

OPEN/CLOSE ABNORMAL

Check the

Connection of CN05.

YES

NO

Reconnected it.

YES

Check IC12 Pin 2 10 .

NO

Check Front.

Check the connection
of MD's Drawer Motor

YES

Replace IC12.

Check IC12 Pin 5 6 .

D. Video abnormal

Check Video Jack.

VIDEO ABNORMAL

Refer to Video part.

Refer to MPEG part.

Replace B/D.

Check the disc.

PICTURE ABNORMAL

R299/R402 option

Check MPEG part.

Replace MAIN B/D.

5. ETC

2-14

IC BLOCK DIAGRAMS & PIN

DESCRIPTION

1. IC25 (STi5505 DVD BACKEND-DECODER)
PIN DESCRIPTION

Pin Name Type Function

SUPPLIES

1, 18, 34, 67, 75, 86, 95,
102, 110, 119, 130, 139,

149, 159, 171, 184, 208

V

DD

Power Supply (3.3 V)

4, 19, 35, 68, 77, 87, 96,
103, 111, 120, 131, 140,

150, 160, 172, 185, 200

GND Ground

53, 60 V

DDA

Analog Power Supply for DENC D/A Converters (3.3 V)

54, 61 V

SSA

Analog Ground for DENC D/A Converters

48 V

DDA_PCM

Analog Power Supply for PLL PCM (3.3 V)
49 V_REF_PCM Analog Reference for PLL PCM (3.3 V)
50 V

SSA_PCM

Analog Ground for PLL PCM

FRONT-END INTERFACE

36 B_DATA I I

2

S Data (DVD) or PARA_DATA[2] (DVD//) or Link Data

(DVB/DSS)
40 B_WCLK I/O I

2

S Word Clock or NRSS_CLK (DVB/DSS)

37 B_BCLK I I

2

S Bit Clock (DVD) or PARA_DATA[3] (DVD//) or Link

Bit Clock (DVB/DSS)
38 B_FLAG I Error Flag (DVD) or PARA_DATA [4] (DVD//) or Link

Sync (DVB/DSS)
39 B_SYNC I Sector / Abs Time Sync (DVD) or PARA_DATA[5]

(DVD//) or Link Not Valid (DVB/DSS)
42 B_V4 I Versatile Input Pin (Subcode Input) or NRSS_IN

(DVB/DSS)

VIDEO OUTPUT INTERFACE

57 R_OUT O Red Output
56 G_OUT O Green Output
55 B_OUT O Blue Output
63 C_OUT O Chroma Output
64 CV_OUT O Composite Video Output
62 Y_OUT O Luma Output
59 I_REF_DAC_RGB I DAC Current Reference
66 I_REF_DAC_YCC I DAC Current Reference
58 V_REF_DAC_RGB I DAC Voltage Reference
65 V_REF_DAC_YCC I DAC Voltage Reference

117 OSD_ACTIVE I/O OSD Active
118 PIXCLK_27MHz I System Clock Input

51

HSYNC

I/O Horizontal Sync

52 ODD/EVEN I/O Vertical Sync

AC-3/MPEG1-2 AUDIO OUTPUT INTERFACE

43 SCLK O Serial Bit Clock
44 PCM_OUT0 O Audio Serial Output Data 0
24 PCM_OUT1 O Audio Serial Output Data 1
21 PCM_OUT2 O Audio Serial Output Data 2
45 PCM_CLK I/O PCM Clock In or Out
46 LRCLK O Left/Right Clock
47 SPDIF_OUT I/O S/PDIF Output (Tristated after reset)

EXTERNAL INTERRUPTS

23, 25 IRQ[0:1] I External Interrupts

2-15

IC BLOCK DIAGRAMS & PIN

DESCRIPTION

1. IC25 (STi5505 DVD BACKEND-DECODER)
PIN DESCRIPTION

Pin Name Type Function

SUPPLIES

1, 18, 34, 67, 75, 86, 95,
102, 110, 119, 130, 139,

149, 159, 171, 184, 208

V

DD

Power Supply (3.3 V)

4, 19, 35, 68, 77, 87, 96,
103, 111, 120, 131, 140,

150, 160, 172, 185, 200

GND Ground

53, 60 V

DDA

Analog Power Supply for DENC D/A Converters (3.3 V)

54, 61 V

SSA

Analog Ground for DENC D/A Converters

48 V

DDA_PCM

Analog Power Supply for PLL PCM (3.3 V)
49 V_REF_PCM Analog Reference for PLL PCM (3.3 V)
50 V

SSA_PCM

Analog Ground for PLL PCM

FRONT-END INTERFACE

36 B_DATA I I

2

S Data (DVD) or PARA_DATA[2] (DVD//) or Link Data

(DVB/DSS)
40 B_WCLK I/O I

2

S Word Clock or NRSS_CLK (DVB/DSS)

37 B_BCLK I I

2

S Bit Clock (DVD) or PARA_DATA[3] (DVD//) or Link

Bit Clock (DVB/DSS)
38 B_FLAG I Error Flag (DVD) or PARA_DATA [4] (DVD//) or Link

Sync (DVB/DSS)
39 B_SYNC I Sector / Abs Time Sync (DVD) or PARA_DATA[5]

(DVD//) or Link Not Valid (DVB/DSS)
42 B_V4 I Versatile Input Pin (Subcode Input) or NRSS_IN

(DVB/DSS)

VIDEO OUTPUT INTERFACE

57 R_OUT O Red Output
56 G_OUT O Green Output
55 B_OUT O Blue Output
63 C_OUT O Chroma Output
64 CV_OUT O Composite Video Output
62 Y_OUT O Luma Output
59 I_REF_DAC_RGB I DAC Current Reference
66 I_REF_DAC_YCC I DAC Current Reference
58 V_REF_DAC_RGB I DAC Voltage Reference
65 V_REF_DAC_YCC I DAC Voltage Reference

117 OSD_ACTIVE I/O OSD Active
118 PIXCLK_27MHz I System Clock Input

51

HSYNC

I/O Horizontal Sync

52 ODD/EVEN I/O Vertical Sync

AC-3/MPEG1-2 AUDIO OUTPUT INTERFACE

43 SCLK O Serial Bit Clock
44 PCM_OUT0 O Audio Serial Output Data 0
24 PCM_OUT1 O Audio Serial Output Data 1
21 PCM_OUT2 O Audio Serial Output Data 2
45 PCM_CLK I/O PCM Clock In or Out
46 LRCLK O Left/Right Clock
47 SPDIF_OUT I/O S/PDIF Output (Tristated after reset)

EXTERNAL INTERRUPTS

23, 25 IRQ[0:1] I External Interrupts

2-16

Pin Name Type Function

EXTERNAL MEMORY INTERFACE

161-170, 173-183 ADR[1:21] I/O External Memory Address Bus
141-148, 151-158 DATA[0:15] I/O External Memory Data Bus

128

RAS1/HOLDREQ

O DRAM RAS or reserved
136 WAIT/READY I/O External Wait States or Reserved
133

R/

W/DMAACK

I/O DRAM R/W Strobe or Reserved

121, 122

BE[0:1]

O Byte enable
129

CAS0/HOLDACK

O/I DRAM CAS or Reserved

132

CAS1/DMAREQ

O DRAM CAS or Reserved

124-126

CE[1:3]

O Chip Select for Banks 1 - 3
135

CS

I Reserved
137 PROCCLK I/O ST20 Clock or Reserved
127

RAS0/CE0

O DRAM RAS or Chip Select for Bank 0
134 DMAXFER I Reserved
138

PPC_MODE

I Reserved

123

OE

I/O Output Enable or Reserved

SDAV/P1394 INTERFACE

30 TEST1 I/O DATA_RX/STROBE_TX (SDAV Mode) or SDAV_CLK

(P1394 Mode) or PARA_DATA[6] (DVD//)

31 TEST2 I/O STROBE_RX/DATA_TX (SDAV Mode) or

DATA_IN/DATA_OUT (P1394 Mode) or
PARA_DATA[7] (DVD//)

32 TEST3 I/O Direction (SDAV Mode) or DATA_VALID In/Out (P1394

Mode)

MISCELLANEOUS

41 TEST5 O NRSS_OUT (DVB/DSS)
33 TEST4 I PARA_DVALID (DVD//) : Data valid on front end parallel

interface

PERIPHERALS

FRONT-END

INTERFACE

DMA

GENERIC

EMI

SDRAM I/F

DENC

CENTRAL

COMMAND

PORT

DMAs

COMMUNICATIONS

ARBITER

ST20 ARBITER & MEMORY CONTROLLER

CPU
(C2)

CLOCK

GENERATION

SMI

SDRAM

BLOCK MOVE

CD FIFOs COMMAND I/F

SDRAM ARBITER (LMC)

OSD AND

SP DECODER

VIDEO

DECODER

AUDIO

DECODER

CACHE SUBSYSTEM

RID TAP

REFILL

CONTROL

ICACHE

SRAM

DCACHE

DIAGNOSTIC

CONTROLLER

CPU ARBITER

MPEG

MPEG

TELETEXT

DEBUG

BLOCK MOVE

P
A
D
S

P
A
D
S

SDAV/P1394

INTERFACE

DMA

BLOCK DIAGRAM

2-17

120
119
118
117
116
115
114
113
112
111
110
109
108
107
106
105

208

206

205

204

136
135
134
133
132
131
130
129
128
127
126
125
124
123
122
121

140
139
138
137

143
142
141

147
146
145
144

149
148

153
152
151
150

156
155
154

203

202

201

200

199

198

197

196

195

194

193

192

191

190

189

188

187

186

185

184

183

182

181

180

179

178

177

176

175

174

173

172

171

170

169

168

167

166

165

164

163

160

159

158

157

162

161

207

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52

53545556575859606162636465666768697071727374757677787980818283848586888990919287939495969798100

101

102

103

104

99

V

DD

PIO3[7]
PIO2[0]

GND
PIO2[3]
PIO2[4]
PIO2[5]
PIO2[7]
PIO1[0]
PIO1[2]
PIO1[5]
PIO1[6]
PIO1[7]
PIO4[7]
PIO0[0]
PIO0[3]
PIO0[4]

V

DD

GND
PIO0[5]

PIO0[6]/PCM_OUT2

PIO0[7]

IRQ[0]

PCM_OUT1

IRQ[1]

PWM0/OSLINK_SEL

PWM1/BOOTFROMROM

PWM2

RST
TEST1
TEST2
TEST3
TEST4

V

DD

GND
B_DATA
B_BCLK
B_FLAG
B_SYNC

B_WCLK

TEST5

B_V4

SCLK

PCM_OUT0

PCM_CLK

LRCLK

SPDIF_OUT

V

DDA_PCM

V_REF_PCM

V

SSA_PCM

HSYNC

ODD/EVEN

V

DDA

V

SSA

B_OUT

G_OUT

R_OUT

I_REF_DAC_RGB

V_REF_DAC_RGB

V

DDA

V

SSA

Y_OUT

C_OUT

CV_OUT

V_REF_DAC_YCC

I_REF_DAC_YCC

V

DD

GND

AD[4]

AD[5]

AD[6]

AD[7]

AD[8]

AD[9]

V

DD

MEMCLKOUT

GND

AD[0]

AD[1]

AD[2]

AD[3]

AD[11]

AD[10]

SDCS[0]

SDCS[1]

V

DD

GND

SDRAS

SDCAS

SDWE

DQML

DQ[0]

DQ[1]

DQ[2]

V

DD

GND

DQ[3]

DQ[4]

DQ[5]

DQ[6]

DQ[7]

V

DD

GND

MEMCLKIN

DQMU

DQ[8]

DQ[9]

DQ[10]

DQ[11]

V

DD

GND

DQ[12]

DQ[13]

DQ[14]

DQ[15]

AUXCLK

OSD_ACTIVE

PIXCLK_27MHz

V

DD

GND

BE[1]

OE

CE[1]

CE[2]

CE[3]

RAS0/CE[0]

RAS1

CAS0/HOLDACK

V

DD

GND

CAS1/DMAREQ

R/W/DMAACK

DMAXFER

CS

WAIT/READY

PROCCLK

PPC_MODE

V

DD

GND

DATA[0]

DATA[1]

DATA[2]

DATA[3]

DATA[4]

DATA[5]

DATA[6]

DATA[7]

V

DD

GND

DATA[8]

DATA[9]

DATA[10]

DATA[11]

DATA[12]

DATA[13]

VDDPIO3[6]

PIO3[5]

PIO3[4]

PIO3[3]

PIO3[2]

PIO3[1]

PIO3[0]

GND

PIO1[4]

PIO1[3]

PIO4[6]

PIO4[5]

PIO4[4]

PIO4[3]

PIO4[2]

PIO4[1]

PIO4[0]

TRST

TDO

TCK

TMS

TDI

GND

VDDADR[21]

ADR[20]

ADR[19]

ADR[18]

ADR[17]

ADR[16]

ADR[15]

ADR[14]

ADR[13]

ADR[12]

ADR[11]

GND

VDDADR[10]

ADR[9]

ADR[8]

ADR[7]

ADR[6]

ADR[5]

ADR[4]

ADR[3]

ADR[2]

ADR[1]

GND

VDDDATA[15]

DATA[14]

STi5505

PQFP208

(Top View)

BE[0]

PIN CONNECTIONS

2-18

2. IC19 (PCM1600 6CH DAC)
PIN DESCRIPTION

PIN NAME I/O DESCRIPTION

1 ZERO1 O Zero Data Flag for V

OUT

1.

2 ZERO2 O Zero Data Flag for V

OUT

2.

3 ZERO3 O Zero Data Flag for V

OUT

3.

4 ZERO4 O Zero Data Flag for V

OUT

4.

5 ZERO5 O Zero Data Flag for V

OUT

5.

6 ZERO6 O Zero Data Flag for V

OUT

6.
7 AGND — Analog Ground
8V

CC

— Analog Power Supply, +5V

9V

OUT

6 O Voltage Output of Audio Signal Corresponding to Rch on DATA3.

10 V

OUT

5 O Voltage Output of Audio Signal Corresponding to Lch on DATA3.

11 V

OUT

4 O Voltage Output of Audio Signal Corresponding to Rch on DATA2.

12 V

OUT

3 O Voltage Output of Audio Signal Corresponding to Lch on DATA2.

13 V

OUT

2 O Voltage Output of Audio Signal Corresponding to Rch on DATA1.

14 V

OUT

1 O Voltage Output of Audio Signal Corresponding to Lch on DATA1.

15 V

COM

2 O Common Voltage Output. This pin should be bypassed with a 10µF capacitor to AGND.

16 V

COM

2 O Common Voltage Output. This pin should be bypassed with a 10µF capacitor to AGND.
17 AGND6 — Analog Ground
18 V

CC

6 — Analog Power Supply, +5V
19 AGND5 — Analog Ground
20 VCC5 — Analog Power Supply, +5V
21 AGND4 — Analog Ground
22 VCC4 — Analog Power Supply, +5V
23 AGND3 — Analog Ground
24 VCC3 — Analog Power Supply, +5V
25 AGND2 — Analog Ground
26 VCC2 — Analog Power Supply, +5V
27 AGND1 — Analog Ground
28 VCC1 — Analog Power Supply, +5V
29 AGND0 — Analog Ground
30 VCC0 — Analog Power Supply, +5V
31 NC I No Connection. Must be open.
32 NC I No Connection. Must be open.
33 MDO O Serial Data Output for Function Register Control Port

(3)

34 MDI I Serial Data Input for Function Register Control Port

(1)

35 MC IN Shift Clock for Function Register Control Port

(1)

36 ML IN Latch Enable for Function Register Control Port

(1)

37 RST I System Reset, Active LOW

(1)

38 SCLKI I System Clock In. Input frequency is 256, 384, 512 or 768fS.

(2)

39 SCLKO O Buffered Clock Output. Output frequency is 256, 384, 512, or 768fS and one-half of 256, 384, 512, or 768f

S.

40 BCK IN Shift Clock Input for Serial Audio Data

(2)

41 LRCK IN Left and Right Clock Input. This clock is equal to the sampling rate, fS.

(2)

42 TEST — Test Pin. This pin should be connected to DGND.

(1)

43 V

DD

— Digital Power Supply, +3.3V
44 DGND — Digital Ground for +3.3V
45 DATA1 IN Serial Audio Data Input for V

OUT

1 and V

OUT

2

(2)

46 DATA2 IN Serial Audio Data Input for V

OUT

3 and V

OUT

4

(2)

47 DATA3 IN Serial Audio Data Input for V

OUT

5 and V

OUT

6

(2)

48 DATA1 IN Serial Audio Data Input for V

OUT

1 and V

OUT

2

NOTES: (1) Schmitt-Trigger input with internal pull-down, 5V tolerant. (2) Schmitt-Trigger input, 5V tolerant. (3) Tri-state output.

2-19

Top View LQFP, MQFP

36
35
34
33
32
31
30
29
28
27
26
25

ML
MC
MDI
MDO
NC
NC
V

CC

0
AGND0
VCC1
AGND1
V

CC

2
AGND2

ZEROA

DATA3

DATA2

DATA1

DGND

VDDTEST

LRCK

BCK

SCLKO

SCLKI

RST

V

OUT

2

V

OUT

1

V

COM

2

V

COM

1

AGND6

V

CC

6

AGND5

V

CC

5

AGND4

V

CC

4

AGND3

V

CC

3

1
2
3
4
5
6
7
8

9
10
11
12

ZERO1
ZERO2
ZERO3
ZERO4
ZERO5
ZERO6

AGND

V

CC

V

OUT

6

V

OUT

5

V

OUT

4

V

OUT

3

48 47 46 45 44 43 42

41 40 39 38

13 14 15 16 17 18 19 20 21 22 233724

PCM1600
PCM1601

Audio
Serial

I/F

Output Amp and

Low-Pass Filter

DAC

DAC

DAC

DAC

DAC

DAC

8x

Oversampling

Digital Filter

with

Function

Controller

Enhanced
Multi-level

Delta-Sigma

Modulator

Output Amp and

Low-Pass Filter

Output Amp and

Low-Pass Filter

Output Amp and

Low-Pass Filter

Output Amp and

Low-Pass Filter

Output Amp and

Low-Pass Filter

BCK

LRCK

DATA1
DATA2
DATA3

Serial

Control

I/F

System Clock

Manager

Zero Detect

Power Supply

TEST

RST

ML

MC

MDI

MDO

V

OUT

1

V

OUT

2

V

OUT

5

V

OUT

6

V

OUT

3

V

COM

1

V

COM

2

V

OUT

4

ZERO1

ZERO2

ZERO3

ZERO4

ZERO5

ZERO6

V

DD

DGND

ZEROA

SCLKI

System Clock

SCLKO

V

CC

AGND

V

CC

0

AGND0

V

CC

1-6

AGND1-6

BLOCK DIAGRAM

PIN CONNECTIONS

2-20

3. IC26 (MBM29F800BA FLASH ROM)
PIN DESCRIPTION

LOGIC SYMBOL

BLOCK DIAGRAM

2-21

A

15

A

14

A

13

A

12

A

11

A

10

A

9

A

8

N.C.
N.C.

WE

RESET

N.C.
N.C.

RY/BY

A

18

A

17

A

7

A

6

A

5

A

4

A

3

A

2

A

1

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24

48
47
46
45
44
43
42
41
40
39
38
37
36
35
34
33
32
31
30
29
28
27
26
25

MBM29F800TA/MBM29F800BA

Standard Pinout

TSOP(I)

A

16

BYTE
V

SS

DQ15/A

-1

DQ

7

DQ

14

DQ

6

DQ

13

DQ

5

DQ

12

DQ

4

V

CC

DQ

11

DQ

3

DQ

10

DQ

2

DQ

9

DQ

1

DQ

8

DQ

0

OE
V

SS

CE
A

0

(Marking Side)

FPT-48P-M19

PIN CONNECTIONS

2-22

4. IC22, IC23 (KM416S1 120D 16M SDRAM)
PIN DESCRIPTION

Pin Name Input Function

CLK System Clock Active on the positive going edge to sample all inputs.
CS Chip Select

Disables or enables device operation by masking or enabling all inputs except
CLK, CKE and L(U)DQM

CKE Clock Enable

Masks system clock to freeze operation from the next clock cycle.
CKE should be enabled at least one cycle prior to new command.
Disable input buffers for power down in standby.

A0 ~ A10/AP Address

Row / column addresses are multiplexed on the same pins.
Row address : RA0 ~ RA10, column address : CA0 ~ CA7

BA Bank Select Address

Selects bank to be activated during row address latch time.
Selects bank for read/write during column address latch time.

RAS Row Address Strobe

Latches row addresses on the positive going edge of the CLK with RAS low.
Enables row access & precharge.

CAS Column Address Strobe

Latches column addresses on the positive going edge of the CLK with CAS low.
Enables column access.

WE Write Enable

Enables write operation and row precharge.
Latches data in starting from CAS, WE active.

L(U)DQM Data Input/Output Mask

Makes data output Hi-Z, tSHZ after the clock and masks the output.

Blocks data input when L(U)DQM active.
DQ0 ~ 15 Data Input/Output Data inputs/outputs are multiplexed on the same pins.
VDD/VSS Power Supply/Ground Power and ground for the input buffers and the core logic.

VDDQ/VSSQ Data Output Power/Ground

Isolated power supply and ground for the output buffers to provide improved noise

immunity.
N.C/RFU

No Connection/
Reserved for Future Use

This pin is recommended to be left No Connection on the device.

2-23

Samsung Electronics reserves the right to
change products or specification without
notice.

*

Bank Select

Data Input Register

512K x 16

512K x 16

Sense AMP

Output BufferI/O Control

Column Decoder

Latency & Burst Length

Programming Register

Address Register

Row Buffer

Refresh Counter

Row Decoder Col. Buffer

LRAS

LCBR

LCKE

LRAS LCBR LWE LDQM

CLK CKE CS RAS CAS WE L(U)DQM

LWE

LDQM

DQi

CLK

ADD

LCAS LWCBR

Timing Register

BLOCK DIAGRAM

VDD
DQ0
DQ1

VSSQ

DQ2
DQ3

VDDQ

DQ4
DQ5

VSSQ

DQ6
DQ7

VDDQ

LDQM

WE
CAS
RAS

CS
BA

A10/AP

A0
A1
A2
A3

VDD

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25

50
49
48
47
46
45
44
43
42
41
40
39
38
37
36
35
34
33
32
31
30
29
28
27
26

VSS
DQ15
DQ14
VSSQ
DQ13
DQ12
VDDQ
DQ11
DQ10
VSSQ
DQ9
DQ8
VDDQ
N.C/RFU
UDQM
CLK
CKE
N.C
A9
A8
A7
A6
A5
A4
VSS

50PIN TSOP (II)

(400mil x 825mil)

(0.8 mm PIN PITCH)

PIN CONNECTIONS

2-26

5. IC91 (CXP501 12 FRONT u-COM)
PIN DESCRIPTION

PIN NO.

1
2
3
4
5
6
7
8

9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40

DESCRIPTION

P5
P6
P7
P8

P9
P10
P11
P12
P13
P14
P15
P16
P17
N.C
N.C
N.C
N.C

G1

G2

G3

G4

G5

G6

G7

G8

G9
G10
G11
N.C
N.C
N.C

RESET

N.C

VDD

N.C
N.C
N.C
N.C

KBDINCLK

KBDIN

REMARK PIN NO.

41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80

DESCRIPTION

N.C
N.C

GND

KBDOUTCLK

N.C

KBDOUT

POWERON

SOUNDMUTE

N.C

N.C
RETURN0
RETURN1
RETURN2
RETURN3

SYSID_O

SYSID_I
NOT USED
NOT USED

N.C

N.C
NOT USED
NOT USED

SCAN0
SCAN1

N.C

N.C

N.C

SCAN5

N.C

N.C

GND

XTAL

N.C

EXTAL

VDD

VP (-28V)

P1
P2
P3
P4

REMARK

FIP

NO CONNECTION

NO CONNECTION

NO CONNECTION

NO CONNECTION

NO CONNECTION

FIP

NO CONNECTION

SYSTEM REMOCON

KEY SCAN RETURN

KEY SCAN

KEY SCAN

TO MAIN PCB

NO CONNECTION

FROM MAIN PCB

FROM MAIN PCB

NO CONNECTION

NO CONNECTION

TO MAIN PCB

NO CONNECTION

5 V

5 V

FIP

2-27

80 79 78 77 76 75 74 73 72 71 70 69 68 67 66 65

25

G8

G9

G10

G11

P4

P3

P2

P1

-28V

VDD

EXTAL

XTAL

GND

SCAN5

RESET

VDD

KBDINCLK

KBDIN

26 27 28 29 30 31 32 33 34 35 36 37 38 39 40

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

17

18

19

20

21

22

23

24

P5

P6

P7

P8

P9

P10

P11

P12

P13

P14

P15

P16

P17

G1

G2

G3

G4

G5

G6

G7

64

63

62

61

60

59

58

57

56

55

54

53

52

51

50

49

48

47

46

45

44

43

SCAN1

SCAN0

NOT USED

NOT USED

NOT USED

NOT USED

SYSIN_I

SYSIN_O

RETURN3

RETURN2

RETURN1

RETURN0

SOUNDMUTE

POWERON

KBDOUT

KBDOUTCLK

GND

42

41

PIN CONNECTIONS

2-55

1 9A08145200 ORNAMENT,DVD KGX1A221WC11
2 9A08145100 DOOR,DVD KGR1A176K17
3 9A06240500 WINDOW 1A154Y KGU1A154Y
4 9A06224200 BADGE,TEAC BGB1A047
5 9A08143700 PANEL,AL KKM3A054VC11

6 9A07363000 PANEL , SUB KGW3A179ZK64
7 9A06863500 WINDOW,SENSOR KGU2A155
8 9A07301300 INDICATOR,POWER KGL2A120
9 9A07301200 KNOB , POWER KBT2A387ZK64

10 9A06316000 KNOB , TACT KBT1A386WK64
11 9A06239700 KNOB , TACT KBT1A410C13

12 9A06314300 KNOB , TACT (OPEN/CLOSE) KBT1A385YK64
13 9A06677600 SIDE BAR KKM1A062C11
14 9A06229300 CUSHION , FOOT KHG1A039Z
15 9A06315500 FOOT KKL1A047ZK63

16 9A08158500 CHASSIS,BOTTOM KUA2A179
17 9A08144400 SUPPORT,MECHA (A) KMH1A097
18 9A08144500 SUPPORT,MECHA (B) KMH1A098
19 9A06315900 TOP CABINET KKC3B077S21
20 9A08144300 BRACKET PCB KMD1A403

21 9A08144200 PANEL,REAR [J] KKF2A191WK59

9A08158600 PANEL,REAR [US, C] KKF2A191YK59

9A08152200 PANEL,REAR [E] KKF3A191XK59
22 9A06754900 BUSHING,AC CORD KHR1A028
23 9A08144000 POWER,CORD [J] BJA2J049Z

9A08043100 CODE,POWER [US, C] BJA523FBY

9A08152100 POWER,CORD [E] BJA2B043Z
24 9A08144100 MECHA ASS'Y KJDTVM501
25 9A07290000 BRACKET, FLT KMD1A374

26 9A06316200 PLATE,SHIELD KMC1A139
27 9A06241700 RUBBER , TRANS KHG1A143
28 9A06252900 BRACKET , PCB KMD1A081
29

9A05921700 RUBBER KHG1A113
30 9A08143900 SUB PCB ASS'Y KOP11324B

31

9A08144600 MAIN PCB ASS'Y [J, US, C] KOP11307D

9A08144620 MAIN PCB ASS'Y [E] KOP11307B
32 9A08144700 POWER PCB SMPS ASS'Y KOP11319B

S1 9A06229000 SCREW , SPECIAL KHD1A016
S2 9A01397400 SCREW KTS3+8J KTS3+8J
S3 9A01377400 SCREW,KTB3+10G KTB3+10G
S4 9A01535800 SCREW,KTB3+8J KTB3+8J
S5 9A05339200 SCREW KTW3+8J KTW3+8J

S6 9A01377300 SCREW,KTB3+10GFZ KTB3+10GFZ
S7

9A01377200 SCREW KTB3+8JFZ

KTB3+8JFZ
S8 9A05984300 SCREW KTB4+6FFZ KTB4+6FFZ
S9 9A01532600 SCREW KTB3+6J KTB3+6J

S10

9A06316300 SCREW KTB+6F

KTB3+6F

S11 9A06244200 SCREW KTS3+6J KTS3+6J

9A07928800

OWNER'S MNL J, DV-H500 [J]

KQX1A601Z

9A07928600 OWNER'S MNL E/F DV-H500 [US, C] KQX1A588Z
9A07928700 OWNER'S MNL E/F/I/G/S DV-H500 [E] KQX1A590Z
9A08143200

REMOCON XMTR AS KRC-4515B BARTDVH500
9A08143300 CORD,PHONE KJS4M011Z KJS4M011Y
9A05936000 CORD,PIN KJS4N001Y

REF. NO. PARTS NO. DESCRIPTION REMARKS

EXPLODED VIEW

REF. NO. PARTS NO. DESCRIPTION REMARKS

INCLUDED ACCESSORIES

3-56

SECTION 3

ELECTRICAL PARTS LIST

Numbering System of Resistor Numbering System of Capacitor

Example Example

KRD

Type25WattageFShapeJTolerance

101

Value

KCKR

Type1HVoltage

101

ValueKTolerance

B

Peculiarity

Resistor Type Wattage Tolerance

KRD: Carbon 20:1/5W F:= ±1%
KRG: Metal Oxide 25:1/4W J:= ±5%

50:1/2W K:= ±10%
1:1W

KRF: Metal Cement 2:2W

3:3W

KRJ: Carbon DHIP 10:1/10W

14:1/4W

Capacitor Type

Voltage

Tolerance

ECEA Type Other

KCB:Ceramic 0J:6.3V 1H:50V DC C: ±0.25pF
KCC:Ceramic 1A:10V 1:125V DC G: ±2%
KCK:Ceramic 1C:16V KC:400V AC J: ±5%
KCQI:Polyester 1E:25V K: ±10%
KCQP:Polypropylene 1H:50V Z: +80%, –20%
KCQS:Polystyrol 1V:35V
KCUC:CHIP

Notes : • Part numbers are indicated for most mechanical parts.

Please use this part number for parts order.

• The unit of resistance is OHM
K=1000 (OHM ), M=1000 (K ) OHM

• The unit of capacitance is MICROFARAD (µF)
P=10 -6µF

RESISTORS AND CAPACITORS

3-57

9A08144600 MAIN PCB ASS'Y [J, US, C] KOP11307D

9A08144620 MAIN PCB ASS'Y E] KOP11307B
IC02 9A05218300 IC , KA7808-ABTU KVIKA7808A
IC04 9A05218300 IC , KA7808-ABTU KVIKA7808A
CN05 9A05328900 WAFER MOLEX 5267-02A KJP02GA01ZM

CN04 9A05330300 WAFER MOLEX53014-0810 KJP08GA19ZM
IC12 9A05880800 IC , BA6209N MC-D200 KVIBA6209N
D110 9A06239100 MODULE , OPTICAL BJS9L001Z
JK10 9A06869700 JACK , BOARD KJJ4N031Z
IC03 9A06883500 IC , KA7908-ABTU KVIKA7908A

D102- 106 9A01390500 DIODE , 1N4148MT KVD1N4148MT
D108 9A01390500 DIODE , 1N4148MT KVD1N4148MT
D109, 111 9A05194000 DIODE , ZENER MTZJ5.1BT KVDMTZJ5.1BT
L103, 105 9A05356900 COIL , AXAIL 10UH,K KLQ02C100KT
L106, 107 9A05356900 COIL , AXAIL 10UH,K KLQ02C100KT

L115 9A05356900 COIL , AXAIL 10UH,K KLQ02C100KT
Q116 9A05892800 TR , KTC3198YT KVTKTC3198YT
Q119, 121 9A05892800 TR , KTC3198YT KVTKTC3198YT
Q104 9A05895900 TR , KTA1266YT KVTKTA1266YT
Q112- 115 9A05895900 TR , KTA1266YT KVTKTA1266YT

Q117, 118 9A05895900 TR , KTA1266YT KVTKTA1266YT
L109 9A05961400 COIL , CHOCK KLQ04C100KV
L116 9A05961400 COIL , CHOCK KLQ04C100KV
D101 9A06765300 DIODE , MTZJ5.6BT KVDMTZJ5.6BT
IC13- 17 9A07343300 IC , OP AMP NJM2068MD-TE1 BVINJM2068MDTE1

IC1 9A08033200 IC , INVERTOR SMD BVIMC74HC14D
IC9 9A08033200 IC , INVERTOR SMD BVIMC74HC14D
IC6 9A08149000 IC , 232 RECEIVER MC1489D BVIMC1489D
IC7 9A08149100 IC , 232 DRIVER MC1488D BVIMC1488D
IC8 9A08149200 IC , BINARY COUNTER BVI74HC161D

IC10 9A08149300 IC , SN74HC374D BVISN74HC374D
IC11

9A08149400 IC , SN74HC245D BVISN74HC245D
IC18 9A08149500 IC , 74HC32D BVI74HC32D
IC19 9A08149600 IC , DAC PCM1600 BVIPCM1600
IC22, 23

9A08149700 IC , 16M SDRAM KVIHY57V161610D
IC25 9A08149800 IC , MPEG ENCODER BVISTI5505

IC26 9A08149900 IC , FLASH MEMORY 8MBIT TSO BVI29F800BB90EC
IC27 9A08150000 IC , 16MEDO KVIKM416C1204CJ
Q101 9A08150100 TR , MUTE KVIUMZ1N KVIUMZ1N
Q105 9A08150100 TR , MUTE KVIUMZ1N KVIUMZ1N

"Q111, 120 9A08150100 TR , MUTE KVIUMZ1N KVIUMZ1N
Q103 9A08150200 TR , MUTE KVIUMX1N KVIUMX1N
Q106- 110 9A08150200 TR , MUTE KVIUMX1N KVIUMX1N
D107

9A08158300 DIODE SCHOTTKY , RB721QT77

KVDRB721QT77

L108 9A08158400 COIL , 1.8UH K KLQ02C1R8KT
L110- 114

9A08158400 COIL , 1.8UH K

KLQ02C1R8KT
BN01 9A08146100 WIRE ASS'Y , KWB1C911180FM KWB1C911180FM
BN99 9A08146200 WIRE ASS'Y , KWB2B906300EN KWB2B906300EN
CN03

9A08146300 10P HEADER

KJP10GA80ZP
CN06 9A08146400 HEDER ASSEMBLY , 90325-0012 KJP12GA120ZM

CN07

9A08146500 HEDER ASSEMBLY , 90325-0010

KJP10GA120ZM
JK08 9A08146600 JACK BOARD (ORANGE , PLATE) KJJ4M030Z
JK09 9A08146700 JACK BOARD KJJ4R026Z
JK12 9A08146800

JACK S-VIDEO , YKF51-5543

BJJYKF51-5543
JK13 9A08146900 JACK COMPOSITE (GOLD,PLAT) KJJ4M032Z

X101 9A08147000

OSC 27M , OSC

KOX27000

REF. NO. PARTS NO. DESCRIPTION REMARKS

MAIN PCB ASS'Y

3-58

9A08143900 SUB PCB ASS'Y KOP11324B
X901 9A05192900 CRYSTAL , DC-D1800 KOX04194E120C
CN99 9A05329700 WAFER MOLEX53014-0610 KJP06GA19ZM
JK91 9A06230200 JACK , REMOTE(2P) KJJ4N023Z
RZ91- 94 9A06244000 RES , NETWORK KRGSN7X104J

SW91 9A06675300 SWITCH SLIDE KSS2B016Z
RC91 9A06757900 SENSOR , REMOCON BRVPNA4612M00HB
D903 9A01390500 DIODE , 1N4148MT KVD1N4148MT
D981 9A01390500 DIODE , 1N4148MT KVD1N4148MT
D901, 902 9A01390600 DIODE , 1N4148T KVD1N4148T

Q983 9A05196400 TR , DTA114YST KVTDTA114YST
Q901- 903 9A05196500 TR , DTC114YST KVTDTC114YST
Q981, 982 9A05196500 TR , DTC114YST KVTDTC114YST
L901 9A05356900 COIL , AXAIL 10UH,K KLQ02C100KT
S901- 908 9A06671200 SW.TACT EVQ21505R BST1A014ZT

C911 9A08147200 CAP , CERAMIC 100PF 50V J KCBS1H101JT
D906 9A08147300 L.E.D , RED SLR342VCTB7 KVD342VCTB7T089
IC91 9A08147400 IC OTP , CXP50116 BVICXP50116
BN91 9A08145400 WIRE ASS'Y , KWB1B908180EN KWB1B908180EN
BN92 9A08145500 WIRE ASS'Y , KWB1B907150GN KWB1B907150GN

F901 9A08145600 F.I.P HNV-11SM06 KFLHNV-11SM06

REF. NO. PARTS NO. DESCRIPTION REMARKS

SUB PCB ASS'Y

9A08144700 POWER PCB SMPS ASS'Y KOP11319B
CN92

9A05356500 WAFER MOLEX53014-0710 KJP07GA19ZM
CN11 9A05890200 WAFER MOLEX 5267-11A KJP11GA01ZM
CN10 9A06674400 WAFER , 7.92MM (YUNHO) KJP02KA060ZY

REF. NO. PARTS NO. DESCRIPTION REMARKS

POWER PCB ASS'Y

PRINTED IN KOREAKQR1A025Z

TEAC CORPORATION

3-7-3, Nakacho, Musashino-shi, Tokyo 180-8550, Japan Phone: [phone]

TEAC AMERICA, INC. 7733 Telegraph Road, Montebello, California 90640 Phone: [phone]
TEAC CANADA LTD. 5939 Wallace Street, Mississauga, Ontario L4Z 1Z8, Canada Phone: [phone]
TEAC MEXICO, S.A. De C.V Campesinos 184. Col. Granjas Esmeralda. 09810. Mexico Phone: [phone]
TEAC UK LIMITED 5 Marlin House, Marlins Meadow, The Croxley Centre, Watford, Herts. WD1 8YA, U.K. Phone: [phone]
TEAC DEUTSCHLAND GmbH Bahnstrasse 12, 65205 Wiesbaden-Erbenheim, Germany Phone: [phone]
TEAC FRANCE S.A. 17, Rue Alexis-de-Tocqueville, CE 005 92182 Antony Cedex, France Phone: [phone]
TEAC NEDERLAND BV Oeverkruid 15, NL-4941 VV Raamsdonksveer, Nederland Phone: [phone]
TEAC BELGIUM NV/SA c/o TEAC NEDERLAND BV, Oeverkruid 15, NL-4941 VV Raamsdonksveer, Nederland Phone: [phone]
TEAC ITALIANA S.p.A. Via C. Cantù 11, 20092 Cinisello Balsamo, Milano, Italy Phone: [phone]
TEAC AUSTRALIA PTY., LTD. 106 Bay Street, Port Melbourne, Victoria 3207, Australia Phone: [phone]

A.B.N. 80 005 408 462