Tascam VL-A8, VL-A4, VL-A5, LF-S8 User Manual

0 (0)

D00994501A

»

VL-A4/VL-A5 VL-A8/LF-S8

BI-AMPLIFIED NEARFIELD STUDIO MONITOR

OWNER'S MANUAL

BEDIENUNGSANLEITUNG

MANUEL DU PROPRIÉTAIRE

MANUALE DI ISTRUZIONI

MANUAL DEL USUARIO

ENGLISH

DEUTSCH

FRANÇAIS

ITALIANO

ESPAÑOL

ENGLISH

IMPORTANT00 SAFETY INSTRUCTIONS

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE

COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING

TO QUALIFIED SERVICE PERSONNEL.

The lightning flash with arrowhead symbol, within equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

This appliance has a serial number locat-

 

WARNING: TO PREVENT FIRE OR SHOCK

ed on the rear panel. Please record the

 

model number and serial number and

 

HAZARD, DO NOT EXPOSE THIS

retain them for your records.

 

Model number

 

 

 

APPLIANCE TO RAIN OR MOISTURE.

 

 

Serial number

 

 

 

 

 

 

 

 

 

 

 

 

For U.S.A.

TO THE USER

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures.

a)Reorient or relocate the receiving antenna.

b)Increase the separation between the equipment and receiver.

c)Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

d)Consult the dealer or an experienced radio/TV technician for help.

CAUTION

Changes or modifications to this equipment not expressly approved by TEAC CORPORATION for compliance could void the user’s authority to operate this equipment.

2 TASCAM VL-A's

IMPORTANT SAFETY INSTRUCTIONS00

1Read these instructions.

2Keep these instructions.

3Heed all warnings.

4Follow all instructions.

5Do not use this apparatus near water.

6Clean only with dry cloth.

7Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.

8Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.

9Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.

10Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.

11Only use attachments/accessories specified by the manufacturer.

12Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.

13Unplug this apparatus during lightning storms or when unused for long periods of time.

14Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

Do not expose this apparatus to drips or splashes.

Do not place any objects filled with liquids, such as vases, on the apparatus.

Do not install this apparatus in a confined space such as a book case or similar unit.

The apparatus draws nominal non-operating power from the AC outlet with its POWER switch in the off position.

The apparatus should be located close enough to the AC outlet so that you can easily grasp the power cord plug at any time.

An apparatus with Class I construction shall be connected to an AC outlet with a protective grounding connection.

Excessive sound pressure from earphones and headphones can cause hearing loss.

The apparatus draws nominal non-operating power from the AC outlet with its STANDBY/ON in the Standby position.

ENGLISH

TASCAM VL-A's 3

ENGLISH

0Table0

of contents

 

1- INTRODUCTION ...........................................................

4

Main Features ................................................................

4

Supplied Accessories ....................................................

4

Environmental Precautions ............................................

5

Product Care ..................................................................

5

2- CONNECTION AND INSTALLATION.............................

6

Precautions for Connection ...........................................

6

Connection

.....................................................................

6

Installation ......................................................................

 

6

Installing .....................................................the VL-A’s

6

Installing ................................................a Subwoofer

7

Surround ...........................................................Setup

7

Tweeter Output Unit Protective Function

 

(VL-A5/VL ...............................................................-A8)

7

3- NAMES AND FUNCTIONS

.............................................8

VL-A4/VL-A5/VL-A8.........................................................

8

LF-S8 ...............................................................................

9

Dimensions ......................................................................

50

Specifications ..................................................................

51

Block Diagram .................................................................

52

1-INTRODUCTION

Thank you for your purchase of the TASCAM VL-A series, Bi-amplified Nearfield Studio Monitor, and LF-S8, Amplified Subwoofer Monitor. Before connecting and using the unit, please take time to read this manual thoroughly to ensure you understand how to properly set up and connect the VL- A’s, as well as the operation of its many useful and convenient functions. After you have finished reading this manual, please keep it in a safe place for future reference.

Main Features

VL-A4

HF12 W / LF16 W (Instant Maximum) Active Bi-amplified Nearfield Studio Monitor System

0.8" tweeter

4" woofer

VL-A5

HF30 W / LF60 W (Instant Maximum) Active Bi-amplified Nearfield Studio Monitor System

0.8" tweeter

5.25" woofer

LF cut function (500 Hz)

LF correction function: 1.5 dB boost/cut at 150 Hz or 800 Hz

HF correction function: 1.5 dB boost/cut at 3 kHz or 8 kHz

VL-A8

HF50 W / LF90 W (Instant Maximum) Active Bi-amplified Nearfield Studio Monitor System

1" tweeter

8" woofer

LF cut function (500 Hz)

LF correction function: 1.5 dB boost/cut at 150 Hz or 800 Hz

HF correction function: 1.5 dB boost/cut at 3 kHz or 8 kHz

LF-S8

LF50 W (Instant Maximum) Amplified Subwoofer System

8" woofer

HF cut function (40-120 Hz, variable)

Phase switching function

Supplied Accessories

This unit was packed in its carton with special materials in order to prevent any damage during shipment.

Please keep the carton and packing materials in the event you need to transport the unit in the future.

VL-A’s has been packed with the following:

 

VL-A4

VL-A5V

L-A8

LF-S8

 

 

 

 

 

Main unit

2 (1 pair)

2 (1 pair)

2 (1 pair)

1

 

 

 

 

 

Power cable

2 (1 pair)

2 (1 pair)

2 (1 pair)

1

 

 

 

 

 

Owner’s

1

1

1

1

manual

 

 

 

 

Warranty

1

1

1

1

 

 

 

 

 

If any of these items are missing, please contact your TASCAM supplier.

4 TASCAM VL-A's

Environmental Precautions

A speaker unit can be used in most places, but to maintain top performance and prolong operating life, do not place it in the following locations.

On an unsteady surface, or where there is frequent vibration or resonance

Near a window or where it can be exposed to direct sunlight

Near heating or air conditioning vents, or in very hot or cold places

Places with high humidity or poor ventilation

Product Care

Wipe off any dirt or dust with a dry, soft cloth. Do not wipe

with a chemical cleaning cloth, benzene, paint thinner or

alcohol. This can damage the surface of the product.

1-INTRODUCTION00

ENGLISH

TASCAM VL-A's 5

ENGLISH

20-0CONNECTION AND INSTALLATION

Precautions for Connection

 

Installation

When unpacking, do not grab by the front of the unit where the drivers are mounted as this may result in damage to the cone.

Turn off the power switch on the rear panel before connecting the power cord to the unit.

Be sure that the connection is made securely to avoid accidental disconnection.

Adjust the input signal levels on your audio device to the minimum or zero before turning on the power on the rear panel to prevent possible damage to the unit.

Do not use the system continuously for long periods of time at high volume levels to avoid any possible damage to your hearing.

Depending on the TV monitor used with the system, the speaker system may affect the quality of the picture on the monitor. In this case, try various positions to find best place to install the speaker system.

The voltage supplied to the unit should match the voltage as printed on the rear panel.

Use audio cables that are free of damage.

Do not send signals other than audio signals to the unit.

The polarity of an audio cable connected to the unit should match the pin assignments explained in “Connection.”

The speaker placement is important to monitor correct sound.

To get best performance of the speaker system, please follow the instruction explained below.

Installing the VL-A’s

1. The unit should be placed at least 60 cm (100 cm recommended) away from obstacle to the rear and at least 40 cm (60 cm recommended) from any obstacle on either side.

2. Basically, two units and the listener should align to form a regular triangle.

Connection

1. Turn off the power switch.

2. Connect the supplied power cord to the main unit and make sure the plug is inserted completely to prevent it from coming off. Connect the other end of the power cord to an AC outlet.

3. Connect the XLR balanced cable or TRS cable to your audio system to send audio signals. The pin assignments of the XLR balanced cable are shown below.

1: Ground, 2: Hot, 3: Cold

The pin assignments of the TRS balanced cable are shown below.

Tip: Hot, Ring: Cold, Sleeve: Ground

3. The height of units, more precisely, the top of the woofer should come up to where your ears are in normal listening environment.

6 TASCAM VL-A's

2-CONNECTION AND INSTALLATION00

4. Placing the unit vertically is recommended. If you place

the unit horizontally, refer to the diagram below.

Installing a Subwoofer

Adding a subwoofer to the monitor system lets you enjoy rich bass sounds.

The optimum placement of the subwoofer varies according to the placement of the other speakers and the room environment.

The following section explains one of the ways to place the subwoofer.

Surround Setup

This shows the subwoofer placed at the same distance from the listening position as the other speakers.

The example is the placement of the 5.1 channel surround monitor system.

Tweeter Output Unit Protective Function

(VL-A5/VL-A8)

The VL-A5 and VL-A8 tweeter output units use a tempera- ture-sensitive polymer switch as a protective device against excessively high output.

Once this protective function has been activated, the tweeter output will be muted until the temperature of the polymer switch returns to normal.

When treble sounds (output from the tweeter speaker) can not be heard, turn off the power and wait two to three minutes before turning on the power again. Check if the treble sound is output from the speaker.

NOTE

This setup is recommended by ITU, International Telecommunications Union, according to ITU-R BS.775-2 “Multichannel stereophonic sound system with and without accompanying picture.”

DO NOT place any obstacles that may block the flow of air, which is medium of the sound, or create reflected sound, especially, the material of high reflection tendency including glass, mirror or metal. Place those materials away from the path of the sound from VL-A’s.

ENGLISH

TASCAM VL-A's 7

Tascam VL-A8, VL-A4, VL-A5, LF-S8 User Manual

0

 

 

03-NAMES AND FUNCTIONS

 

VL-A4

Rear Panel

Front Panel

VL-A5

Rear Panel

Front Panel

ENGLISH

 

 

VL-A8

Rear Panel

Front Panel

1~ IN jack

This ~ IN jack is used to connect the supplied power cord.

2FUSE holder

This unit is equipped with a fuse. lf the unit does not work, disconnect the power plug from the AC outlet and then contact the nearest qualified service personnel.

3POWER switch

This is used to turn the power on and off.

4INPUT jack

This is a balanced input terminal that uses an XLR balanced cable and TRS PHONE balanced cable combination jack. This INPUT jack connects the unit to an external device.

8 TASCAM VL-A's

5LEVEL CONTROL knob

This is used to adjust the output volume.

6POWER indicator (Front Panel/Rear Panel)

This indicator lights up when the power switch is turned on and AC power is supplied to the ~ IN jack.

7HF CONT switch (VL-A5, VL-A8 only)

This is used to adjust the treble level.

+1.5 dB 8k: Boosts the 8 kHz frequency by 1.5 dB. +1.5 dB 3k: Boosts the 3 kHz frequency by 1.5 dB. -1.5 dB 8k: Cuts the 8 kHz frequency by 1.5 dB.

-1.5 dB 3k: Cuts the 3 kHz frequency by 1.5 dB.

8LF CONT switch (VL-A5, VL-A8 only)

This is used to adjust the bass level.

LF+: Boosts the 150 Hz or 800 Hz frequency by 1.5 dB. LF-: Cuts the 150 Hz or 800 Hz frequency by 1.5 dB.

LF CUT: Cuts bass sounds at a frequency of 500 Hz or lower.

3-NAMES AND FUNCTIONS00

LF-S8

Rear Panel

Front Panel

 

1 POWER switch

 

8 LEVEL CONTROL knob

ENGLISH

 

 

This is used to turn the power on and off.

 

This is used to adjust the output level of the subwoofer

 

2 FUSE holder

 

speaker.

 

 

 

 

This unit is equipped with a fuse. lf the unit does not

9 PHASE switch (0°/180°)

 

work, disconnect the power plug from the AC outlet and

This is used to switch the output phase of the subwoofer

 

then contact the nearest qualified service personnel.

speaker. Depending on speaker placement, or the com-

 

3 ~ IN jack

 

bination of speaker systems, bass sounds may be heard

 

 

differently. If so, try to adjust the output phase using this

 

This ~ IN jack is used to connect the supplied power

 

switch to make bass sounds better for you.

 

cord.

 

 

 

 

 

4INPUT CH1/CH2 jacks

These balanced input jacks suit for both XLR balanced and TRS PHONE balanced connectors, and are typically connected to output jacks on a mixer.

5CROSS FREQ knob

This control is used to set a cutoff frequency between 40 to 120 Hz to cut high or low frequency output from the subwoofer.

6OUTPUT CH1/CH2 jacks

These output jacks connect XLR balanced connectors. High frequency signals are output through the jack (lowfrequency is cut according to the cutoff frequency set with the CROSS FREQ knob). An external device such as a power amplifier is connected to the jack.

When you use the LF-S8 with the VL-A4, VL-A5 or VL-A8, connect both the left (CH1) and right (CH2) INPUT jacks.

7OUTPUT SUB LF jack

This output jack connects XLR balanced connector. Low frequency signals are output through the jack (high frequency is cut according to the cutoff frequency set with the CROSS FREQ knob). The second subwoofer is connected to this jack.

0POWER indicator

This indicator lights up when the power switch is turned on and AC power is supplied to the ~ IN jack.

TASCAM VL-A's 9

WICHTIGE00 SICHERHEITSHINWEISE

Achtung! Gefahr eines Stromschlags. Öffnen Sie nicht das Gehäuse. Es befinden sich keine vom Anwender zu wartenden Teile im Gerät. Lassen Sie das Gerät nur von qualifiziertem Fachpersonal reparieren.

Dieses Symbol, ein Blitz in einem ausgefüllten Dreieck, warnt vor nicht isolierten, elektrischen Spannungen im Inneren des Geräts, die zu einem gefährlichen Stromschlag führen können.

Dieses Symbol, ein Ausrufezeichen in einem ausgefüllten Dreieck, weist auf wichtige Bedienungsoder Sicherheitshinweise in dieser Bedienungsanleitung hin.

Bitte tragen Sie hier die Modellnummer und die Seriennummern (siehe Geräterückseite) ein, um sie mit Ihren Unterlagen aufzubewahren.

Modellnummer

Seriennummer

ACHTUNG! Zum Schutz vor Brand oder Elektroschock:

Setzen Sie dieses Gerät niemals Regen oder erhöhter Luftfeuchtigkeit aus.

DEUTSCH

10 TASCAM VL-A's

WICHTIGE SICHERHEITSHINWEISE00

1Lesen Sie diese Anleitung.

2Bewahren Sie diese Anleitung gut auf und geben Sie das Gerät nur mit dieser Anleitung weiter.

3Beachten Sie alle Warnhinweise.

4Befolgen Sie alle Anweisungen. Benutzen Sie das Gerät nur zu dem Zweck und auf die Weise, wie in dieser Anleitung beschrieben.

5Betreiben Sie dieses Gerät nicht in unmittelbarer Nähe von Wasser. Schützen Sie das Gerät vor Feuchtigkeit und Spritzwasser. Stellen Sie niemals mit Flüssigkeit gefüllte Behälter (Vasen, Kaffeetassen usw.) auf dieses Gerät.

6Reinigen Sie dieses Gerät nur mit einem trockenen Tuch.

7Versperren Sie niemals vorhandene Lüftungsöffnungen. Stellen Sie dieses Gerät nicht an einem räumlich beengten Ort ohne Luftzirkulation auf.

8Stellen Sie das Gerät nicht in der Nähe von Hitze abstrahlenden Geräten (Heizlüfter, Öfen, Verstärker usw.) auf.

9Unterbrechen Sie niemals den Schutzleiter des Netzsteckers und kleben Sie niemals den Schutzkontakt zu. Wenn der mitgelieferte Netzstecker nicht in Ihre Steckdose passt, ziehen Sie einen Elektrofachmann zu Rate.

10Sorgen Sie dafür, dass das Netzkabel nicht gedehnt, gequetscht oder geknickt werden kann

– insbesondere am Stecker und am Netzkabelausgang des Geräts – und verlegen Sie es so, dass man nicht darüber stolpern kann.

11Verwenden Sie nur Zubehör oder Zubehörteile, die der Hersteller empfiehlt.

12Verwenden Sie nur Wagen, Ständer, Stative, Halter oder Tische, die vom Hersteller empfohlen oder mit dem Gerät verkauft werden. Wenn Sie einen Wagen verwenden, bewegen Sie ihn vorsichtig, so dass er nicht umstürzen und Sie verletzen kann.

14Lassen Sie Wartungsarbeiten und Reparaturen nur vom qualifizierten Fachpersonal des Kundendienstes ausführen. Bringen Sie das Gerät zum Kundendienst, wenn es Regen oder Feuchtigkeit ausgesetzt war, wenn Flüssigkeit oder Fremdkörper hinein gelangt sind, wenn es heruntergefallen ist oder nicht normal funktioniert oder wenn das Netzkabel beschädigt ist.

Setzen Sie dieses Gerät nicht Wassertropfen oder –spritzern aus.

Stellen Sie keine mit Flüssigkeiten gefüllten Gegenstände, beispielsweise Vasen, auf das Gerät.

Stellen Sie dieses Gerät nicht in einem geschlossenen Raum, beispielsweise einem Bücherschrank oder dergleichen, auf.

Das Gerät nimmt eine kleine Menge Strom von der Steckdose auf, wenn der Stromschalter (POWER) ausgeschaltet ist.

Das Gerät sollte sich nahe genug an der Steckdose befindet, damit Sie den Netzstecker jederzeit einfach anfassen und abziehen können.

Ein Gerät der Klasse I sollte an eine Steckdose mit Schutzerdung angeschlossen werden.

Übermäßiger Schalldruck von den Ohrund Kopfhörern kann zu Gehörverlust führen.

Das Gerät nimmt eine kleine Menge Strom von der Steckdose auf, wenn der STANDBY/ON-Schalter auf den Bereitschaftsmodus (Standby) geschaltet ist.

13Ziehen Sie den Netzstecker bei Gewitter oder wenn Sie das Gerät längere Zeit nicht benutzen.

DEUTSCH

TASCAM VL-A's 11

Inhalt00

1- EINLEITUNG ...............................................................

12

3- NAMEN UND FUNKTIONEN.......................................

16

Hauptmerkmale ...........................................................

12

VL-A4/VL-A5/VL-A8......................................................

16

Lieferumfang ................................................................

12

LF-S8 ............................................................................

17

Vorsichtsmaßnahmen bei der Aufstellung ...................

13

 

 

Produktpflege ..............................................................

13

Dimensions ......................................................................

50

 

 

Specifications ..................................................................

51

2- AUFSTELLEN UND AUSRICHTEN .............................

14

Block Diagram .................................................................

52

Vorsichtsmaßnahmen beim Anschließen .....................

14

 

 

Anschluss .....................................................................

14

 

 

Aufstellung ...................................................................

14

 

 

Aufstellen von VL-A ...................................................

14

 

 

Aufstellung eines Subwoofers ..................................

15

 

 

Surround-Aufstellung ................................................

15

 

 

Hochtönerausgang-Schutzfunktion

 

 

 

(VR-A5/VL-A8) ...........................................................

15

 

 

DEUTSCH

1-EINLEITUNG

Vielen Dank, dass Sie sich für den TASCAM VL-A NahfeldStudiomonitor mit Doppelverstärkung und LF-S8 Subwoofer-Monitor mit Verstärkung entschieden haben. Bevor Sie das Gerät anschließen und benutzen, empfehlen wir Ihnen, dieses Handbuch aufmerksam durchzulesen. Nur so ist sichergestellt, dass Sie verstehen, wie man den VL-Ax korrekt verkabelt, und wie man seine Funktionsmerkmale richtig nutzt.

Bewahren Sie dieses Handbuch nach dem Lesen gut auf, um bei Bedarf jederzeit darin nachschlagen zu können.

Hauptmerkmale

VL-A4

Aktiver Nahfeld-Studiomonitor mit 12 Watt Hochtonund 16 Watt Tieftonleistung (Zweites Maximum)

20-mm-Hochtöner

100-mm-Woofer

VL-A5

Aktiver Nahfeld-Studiomonitor mit 30 Watt Hochtonund 60 Watt Tieftonleistung (Zweites Maximum)

20-mm-Hochtöner

130-mm-Woofer

Tieftonabsenkungsfunktion (500 Hz)

Tieftonkorrektur: 1,5 dB Anhebung/Absenkung bei 150 Hz oder 800 Hz

Hochtonkorrektur: 1,5 dB Anhebung/Absenkung bei 3 kHz oder 8 kHz

VL-A8

Aktiver Nahfeld-Studiomonitor mit 50 Watt Hochtonund 90 Watt Tieftonleistung (Zweites Maximum)

25-mm-Hochtöner

200-mm-Woofer

Tieftonabsenkungsfunktion (500 Hz)

Tieftonkorrektur: 1,5 dB Anhebung/Absenkung bei 150 Hz oder 800 Hz

Hochtonkorrektur: 1,5 dB Anhebung/Absenkung bei 3 kHz oder 8 kHz

LF-S8

Aktiver Subwoofer mit 50 Watt Tieftonleistung (Zweites Maximum)

200-mm-Woofer

Hochtonabsenkungsfunktion (40-120 Hz, variabel)

Phasenumschaltungsfunktion

Lieferumfang

Dieses Gerät wurde sehr sorgfältig verpackt, um eine Beschädigung während der langen Reise zu vermeiden. Bewahren Sie das Verpackungsmaterial auf, um das Gerät auch später einmal gut geschützt transportieren zu können.

Der Karton sollte zusätzlich zu den VLAx folgenden Inhalt haben:

 

VL-A4

VL-A5V

L-A8

LF-S8

 

 

 

 

 

Hauptgerät

2 (1 Paar)

2 (1 Paar)

2 (1 Paar)

1

 

 

 

 

 

Stromkabel

2 (1 Paar)

2 (1 Paar)

2 (1 Paar)

1

 

 

 

 

 

Bedienungs-

1

1

1

1

anleitung

 

 

 

 

 

 

 

 

 

Garantie

1

1

1

1

 

 

 

 

 

Wenn Teile fehlen, wenden Sie sich bitte an Ihren TASCAMFachhändler.

12 TASCAM VL-A's

Vorsichtsmaßnahmen bei der Aufstellung

Ein Lautsprecher kann in den meisten Umgebungen betrieben werden. Um eine größtmögliche Lebensdauer zu gewährleisten, stellen Sie ihn nicht:

auf unebene oder wackelige Oberflächen, oder wo Vibrationen oder Resonanzen auftreten können,

an Orte mit direkter Sonneneinstrahlung (z. B. an ein Fenster),

in die Nähe von Hitze oder Kälte abstrahlenden Geräten oder an sehr kalte oder sehr heiße Plätze,

an Orte mit hoher Luftfeuchtigkeit oder schlechter Belüftung,

Produktpflege

Wischen Sie Schmutz oder Staub mit einem trockenen

weichen Tuch ab. Vermeiden Sie die Verwendung von

chemischen Reinigungstüchern, Benzol, Farbverdünner und

Alkohol. Diese Substanzen können die Oberfläche des

Produkts beschädigen.

1-EINLEITUNG00

DEUTSCH

TASCAM VL-A's 13

DEUTSCH

20-0AUFSTELLEN UND AUSRICHTEN

Vorsichtsmaßnahmen beim Anschließen

 

Aufstellung

Halten Sie die Vorderseite des Geräts, wo sich die Treiber befinden, beim Auspacken nicht fest, da anderenfalls der Kegel beschädigt werden könnte.

Schalten Sie den auf der Rückseite befindlichen Netzschalter aus, bevor Sie das Netzkabel an das Gerät anschließen.

Vergewissern Sie sich, dass der Anschluss sicher ist, damit das Kabel nicht versehentlich abgetrennt werden kann.

Stellen Sie das Eingangssignal Ihres Audiogeräts auf den Mindestpegel oder Null, bevor Sie den auf der Rückseite befindlichen Netzschalter einschalten, um eine Beschädigung des Lautsprechers zu verhindern.

Verwenden Sie das System nicht über lange Zeit bei hoher Lautstärke, um Hörschäden zu vermeiden.

In Abhängigkeit von der Art des verwendeten Fernsehbildschirms kann dieses Lautsprechersystem die Bildqualität auf dem Bildschirm beeinträchtigen. Probieren Sie in diesem Fall verschiedenen Aufstellungsorte aus, um den besten Platz zum Aufstellen des Lautsprechers ausfindig zu machen.

Die Spannung, mit der das Gerät versorgt wird, sollte der auf der Rückseite des Geräts angeführten Spannung entsprechen.

Verwenden Sie unbeschädigte Audiokabel.

Senden Sie keine anderen Signale als Audiosignale zum Gerät.

Die Polarität eines an das Gerät angeschlossenen Audiokabels sollte mit der Stiftzuordnung, die in „Anschluss“ erklärt ist, übereinstimmen.

Anschluss

1. Drücken Sie den Netzschalter aus.

2. Schließen Sie das mitgelieferte Netzkabel an das Hauptgerät an, und vergewissern Sie sich, dass der Stecker vollständig eingesteckt ist und nicht von allein abgetrennt wird. Schließen Sie das andere Ende des Netzkabels an eine Wandsteckdose an.

3. Schließen Sie das symmetrische Kabel vom Typ XLR oder das TRS-Kabel an Ihr Audiosystem an, um Audiosignale zu senden. Die Stiftzuordnungen für das symmetrische Kabel vom Typ XLR sind unten angeführt.

1: Erde, 2: Strom führend,

3: nicht unter Strom stehend

Die Stiftzuordnungen für das symmetrische Kabel vom Typ TRS sind unten angeführt.

Spitze: Strom führend,

Ring: nicht unter Strom stehend, Muffe: Erde

Die Aufstellung des Lautsprechers ist besonders wichtig für die korrekte Tonwiedergabe.

Um die beste Leistung des Lautsprechersystems zu erzielen, befolgen Sie bitte die nachfolgenden Anleitungen.

Aufstellen von VL-A

1. Das Gerät sollte sich in einem Abstand von mindestens 60 cm (empfohlen: 100 cm) nach hinten und mindestens 40 cm (empfohlen: 60 cm) seitlich von einer Wand befinden.

2. Die zwei Lautsprecher sollten grundsätzlich ein gleichschenkliges Dreieck mit dem Hörer bilden.

3. Die Oberseite der Hochtöner sollte dabei auf gleicher Höhe mit den Ohren des Hörers in der normalen Hörposition sein.

14 TASCAM VL-A's

2-AUFSTELLEN UND AUSRICHTEN00

4. Wir empfehlen eine vertikale Aufstellung des Geräts.

Falls Sie das Gerät waagerecht aufstellen, beziehen Sie

sich bitte auf das folgende Schaubild.

Aufstellung eines Subwoofers

Indem Sie dem Monitor einen Subwoofer hinzufügen, können Sie eine kräftigere Basswiedergabe genießen.

Der optimale Aufstellungsort des Subwoofers hängt von der Aufstellung der anderen Lautsprecher und der Beschaffenheit des Zimmers ab.

Der folgende Abschnitt beschreibt eine Methode zum Aufstelen des Subwoofers.

Surround-Aufstellung

Diese Methode zeigt, dass der Subwoofer in der gleichen Entfernung von der Hörposition wie die anderen Lautsprecher aufgestellt ist.

Das Beispiel zeigt die Aufstellung eines SurroundMonitorsystems mit 5.1 Kanälen.

Hochönerausgang-Schutzfunktion (VR-A5/VL-A8)

Die Hochtönerausgänge VL-A5 und VL-A8 verwenden einen temperaturempfindlichen Polymer-Schalter als Schutzvorrichtung gegen übermäßig hohen Ausgang. Sobald diese Schutzfunktion aktiviert wurde, wird der Hochtönerausgang deaktiviert, bis die Temperatur des Polymer-Schalters auf den Normalwert zurückkehrt.

Wenn keine Höhen (Hochtönerausgang) ausgegeben werden, schalten Sie die Stromversorgung aus, und warten Sie 2 bis 3 Minuten lang, bevor Sie die Stromversorgung erneut einschalten. Vergewissern Sie sich dann, dass die Höhen vom Lautsprechern ausgegeben werden.

HINWEIS

Dieses Aufstellungsbeispiel basiert auf der Empfehlung ITU-R BS.775-2 der Internationalen Fernmelde-Union, „Multikanal-Stereo-System mit und ohne Begleitbild“.

Achten Sie in jedem Fall darauf, dass keine Hindernisse den Luftstrom, der das Medium für die Schallausbreitung darstellt, blockieren oder den Schall reflektieren, insbesondere solche Stoffe wie Glas, Spiegel oder Metall. Halten Sie derartige Stoffe vom Tonpfad des VL-Ax fern.

DEUTSCH

TASCAM VL-A's 15

 

0

 

 

 

03-NAMEN UND FUNKTIONEN

 

 

VL-A4

Rückseite

Vorderseite

 

VL-A5

Rückseite

Vorderseite

DEUTSCH

VL-A8

Rückseite

Vorderseite

1~ Eingangsbuchse (AC IN)

Diese ~ Eingangsbuchse (AC IN) wird für den Anschluss des mitgelieferten Netzkabels verwendet.

2Sicherungsfassung

Dieses Gerät ist mit einer Sicherung ausgestattet. Falls das Gerät nicht funktioniert, trennen Sie den Netzstecker von der Wandsteckdose ab, und wenden Sie sich die nächste qualifizierte Kundendienststelle.

3Stromschalter (POWER)

Dient zum Einund Ausschalten der Stromversorgung.

4Eingangsbuchsee (INPUT)

Dies ist eine Kombination von symmetrischer Eingangsbuchsee mit einem symmetrischen Kabel vom Typ XLR und und einer Telefonbuchse von Typ TRS mit symmetrischem Kabel. Diese Eingangsbuchse dient für den Anschluss eines Zusatzgeräts.

5Pegelregler (LEVEL CONTROL)

Wird zum Einstellen des Ausgangspegels verwendet.

6Leistungsanzeige (POWER) (Vorderseite/Rückseite)

Diese Anzeige leuchtet, wenn der Netzschalter eingeschaltet ist und die ~ Eingangsbuchse (AC IN) mit Strom versorgt wird.

7Hochtonreglerschalter (HF CONT) (nur VL-A5, VL-A8)

Wird zum Einstellen des Höhenpegels verwendet.

+1,5 dB 8k: Erhöht den Pegel der 8-kHz-Frequenz um 1,5 dB. +1,5 dB 3k: Erhöht den Pegel der 3-kHz-Frequenz um 1,5 dB. -1.5 dB 8 k: Verringert den Pegel der 8-kHz-Frequenz um 1,5 dB. -1.5 dB 3 k: Verringert den Pegel der 3-kHz-Frequenz um 1,5 dB.

8Tieftonreglerschalter (LF CONT) (nur VL-A5, VL-A8)

Wird zum Einstellen des Basspegels verwendet.

LF+: Erhöht den Pegel der 150-Hz- oder 800-Hz-Frequenz um 1,5 dB. LF-: Verringert den Pegel der 150-Hz- oder 800-Hz-Frequenz um 1,5 dB. LF CUT: Unterdrückt die Bässe mit einer Frequenz von 500 Hz oder darunter.

16 TASCAM VL-A's

 

 

3-NAMEN UND FUNKTIONEN00

LF-S8

Rückseite

Vorderseite

1Stromschalter (POWER)

Dient zum Einund Ausschalten der Stromversorgung.

2Sicherungsfassung

Dieses Gerät ist mit einer Sicherung ausgestattet. Falls das Gerät nicht funktioniert, trennen Sie den Netzstecker von der Wandsteckdose ab, und wenden Sie sich die nächste qualifizierte Kundendienststelle.

3~ Eingangsbuchse (AC IN)

Diese ~ Eingangsbuchse (AC IN) wird für den Anschluss des mitgelieferten Netzkabels verwendet.

4Eingangsbuchsen (INPUT) CH1/CH2

Dies sind symmetrischen Eingangsbuchsen vom Typ XLR und TRS PHONE, und sie werden typischerweise mit den Ausgangsbuchsen eines Tonmischers verbunden.

5Überschneidungsfrequenzknopf (CROSS FREQ)

Dieser Regler wird verwendet, um eine Grenzfrequenz zwischen 40 und 120 Hz für die Reduzierung der Höhen oder Bässe vom Subwoofer einzustellen.

6Ausgangsklemmen (OUTPUT) CH1/CH2

Dies sind symmetrische Ausgangsbuchsen vom Typ XLR. Die Höhen werden durch die Buchse ausgegeben (die Bässe werden entsprechend der Grenzfrequenz, die mit dem Überschneidungsfrequenzknopf eingestellt wurde, unterdrückt). Ein Zusatzgerät, beispielsweise ein Leistungsverstärker, wird an diese Buchse angeschlossen.

Wenn Sie den LF-S8 mit dem VL-A4, VL-A5 oder VL-A8 verwenden, schließen Sie sowohl die linke (CH1) als auch die rechte (CH2) Eingangsbuchse (INPUT) an.

7Ausgangsbuchse (OUTPUT) SUB LF

Dies ist eine symmetrische Ausgangsbuchse vom Typ XLR. Die Bässe werden durch die Buchse ausgegeben (die Höhen werden entsprechend der Grenzfrequenz, die mit dem Überschneidungsfrequenzknopf eingestellt wurde, unterdrückt). Der zweite Subwoofer sollte an diese Buchse angeschlossen werden.

8Pegelregler (LEVEL CONTROL)

Dieser Regler wird verwendet um den Ausgangspegel des Subwoofers einzustellen.

9Phasenschalter (PHASE) (0°/180°)

Dieser Schalter wird verwendet, um die Ausgangsphase des Subwoofers umzuschalten.

Je nach der Aufstellung des Lautsprechers oder der Kombination der verwendeten Lautsprecher erklingen die Bässe ggf. unterschiedlich. Stellen Sie die Ausgangsphase mit diesem Schalter so ein, dass Sie die beste Basswiedergabe erzielen.

0Leistungsanzeige (POWER)

Diese Anzeige leuchtet, wenn der Netzschalter eingeschaltet ist und die ~ Eingangsbuchse (AC IN) mit Strom versorgt wird.

DEUTSCH

TASCAM VL-A's 17

Loading...
+ 39 hidden pages