Tannoy CMS 601 DC BM, CMS 601 BM, CMS 501 PI, CMS 601 PI, CMS 501 DC PI User Manual

CMS

Tannoy United Kingdom	T: 00 44	(0) 1236 420199	E: [e-mail]
Tannoy Deutschland	T: 00 49	(180) 1111 881	E: [e-mail]
Tannoy France	T: 00 33	(0)1 7036 7473	E: [e-mail]
TC|Group Americas	T: 00 1 [phone]		E: [e-mail]

Tannoy adopts a policy of continuous improvement and product specification is subject to change.

CMS

C E I L I N G M O N I T O R S Y S T E M S

I N S T A L L A T I O N M A N U A L

CMS 501 BM		CMS 601 BM
CMS 501 DC BM		CMS 601 DC BM
CMS 501 PI		CMS 601 PI
CMS 501 DC PI		CMS 601 DC PI
CMS 501 PI back-can		CMS 601 PI back-can

2009 NOVEBER 2ND DATE: REVISION

0480 6481	CMS 501 models TEMPLATE HOLE CUTOUT SIZE: 190mm
	CMS 601 models TEMPLATE HOLE CUTOUT SIZE: 253mm

CMS

CONTENTS

1INTRODUCTION

2UNPACKING

3SAFETY NOTICES

4PRODUCT FEATURE IDENTIFICATION

5ACCESSORIES

6INSTALLATION GUIDE

6.1MECHANICAL INSTALLATION GUIDE FOR SUSPENDED CEILINGS

6.2MECHANICAL INSTALLATION GUIDE FOR SHEET-ROCK CEILINGS

6.3MECHANICAL INSTALLATION INSTRUCTIONS FOR OPTIONAL PLASTER RING

6.4INSTRUCTIONS FOR OPTIONAL PRE-INSTALLATION BACK-CAN (PI MODELS ONLY)

7WIRING AND SETTING UP

8DIMENSIONS

8.1CMS 501 DIMENSIONS

8.2CMS 601 DIMENSIONS

9TECHNICAL SPECIFICATIONS

10PAINTING

11WARRANTY

12DECLARATION OF CONFORMITY

1. INTRODUCTION

Thank you for purchasing this Tannoy Ceiling Monitor System product. This product range is suited for high-level music and speech reinforcement applications requiring exceptional sonic quality with uncompromised reliability.

2. UNPACKING

Every Tannoy product and accessory is carefully inspected before packing. After unpacking, please inspect your product to make sure no damage has occurred in transit. In the unlikely event of any damage, would you please notify your dealer immediately and retain your shipping carton, as your dealer may ask you to return the faulty unit to him for inspection.

Each CMS loudspeaker is packed in pairs and provided with the following accessories as standard; C Ring, tile-bridge kit, grille, cut-out template, and paint mask. A plaster (mud) ring is also available as an optional extra.

3. SAFETY NOTICES

Some regional construction codes require the use of a secondary method of securing loudspeakers in ceiling to provide security of a back up support. A secondary support line should be attached from the safety loop on the rear of the product to a source point on the ceiling. For PI models, the secondary

support. line should be attached from the back of the driver chasis to a source point on the ceiling. Please consult the relevant construction codes in your region.

When using a power driver to install the product it is essential to use the correct torque level settings to avoid over tightening and damage to the ceiling material or clamps.

Recommended torque setting: 1.5Nm

Tannoy will not be held responsible for any damages caused by the improper installation of these loudspeakers.

Electrical Safety Notice: to comply with the standard UL1480, metal-clad flexible conduit (BX) is required for connection to the terminal block for proper earth grounding.

In order to comply with UL regulations, the PI back-can must always be used with the CMS PI models.

SAFETY NOTE:

In order to comply with relevant fire safety regulations (i.e. BS 5839:1998), it is required that in the event of fire, that failure of the circuit to which the loudspeaker is connected does not occur before evacuation of the building is complete. Suitable measures include: -

a)use of terminal blocks (for connection to primary) with a melting point of not less than 650°C, for example constructed from ceramic materials;

b)use of terminal blocks of a lower melting point but protected with thermal insulation;

c)use of terminal blocks such that, on melting, an open-circuit or a short-circuit does not occur.

2		3

CMS

4. PRODUCT FEATURE IDENTIFICATION:

Conduit/Cable Clamp		Tuning Port

Euro Type Connector

Mounting Wings

5. ACCESSORIES:

Each product is supplied with the following accessories as standard:

Rotary Switch

C-Ring				Tile bridge kit

Note: A tile bridge kit must always be used when installing into suspended ceiling tiles

Screws for mounting wings

Fig 1.1: The blind-mount (BM) models come with a pre-fitted back-can

Grille

Screws for		Rotary Switch		Euro Type Connector
mounting wings

Tuning Port

Paint Mask

Fig 1.2: A pre-install (PI) model shown without optional pre-install back-can

Safety Notice: In order to comply with UL regulations, the PI back-can must always be used with the CMS PI models.

Euro Type Plug	Euro Type Connector

Optional accessories:

Cut-out template

Foam port-plug

NOTE: Only supplied with PI models for applications where

PI models are being installed without back-cans. Do not use the foam port-plug if you are installing the PI product into a back-can.

Conduit Knock-out points

Plaster (Mud) Ring

Fig 1.3: Optional pre-install (PI) back-can for PI models

Note that the 601 PI models have the transformer pre-attached to the inside of the 601 PI back-can, whereas the 501 models have the transformer pre-attached to the speaker assembly.

4		5