Page 1
LIGHTNING
PUSHCHAIR
USER & WORKSHOP MANUAL
FOR THE
Page 2
User & Workshop Manual for the Lightning Upholstery
2
CONTENTS
Safety Rules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Weight Limitations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Pushchair Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Pushchair Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Specications Chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
1.0 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
2.0 Contact Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
3.0 Intended Use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
4.0 Declaration Of Conformity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
5.0 Unpacking & Preparing The Pushchair For Use . . . . . . . . . . . . . . . . 8
6.0 Unfolding The Pushchair . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
7.0 Setting Up & Adjusting The Pushchair . . . . . . . . . . . . . . . . . . . . . . . 9
7.1 Folding & Carrying . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
7.2 Seat Back Angle Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
7.3 Seat Depth Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
7.4 Footrest Height Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
7.5 Footplate Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
7.6 Adjusting & Using The Safety Harness . . . . . . . . . . . . . . . . . . . . 13
7.7 Brake System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
8.0 Installing Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
8.1 Headrest Extension . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
8.2 Canopy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
8.3 Padded Headrest . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
8.4 Heel Loop and Ankle Cuffs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
8.5 Padded Harness Covers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
8.6 Trunk Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
9.0 Instructions For Transporting The Lightning Pushchair . . . . . . . . . 18
9.1 Prepare Lightning for Transportation . . . . . . . . . . . . . . . . . . . . . . 18
9.2 Attach the Set of Tie-Downs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
9.3 Assembly Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
9.4 Attach the Lightning Pushchair to Vehicle . . . . . . . . . . . . . . . . . 19
10.0 Instructions For Attaching The Work-N-Play Tray . . . . . . . . . . . . . . . 20
10.1 Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
10.2 Attaching and Removing the Tray . . . . . . . . . . . . . . . . . . . . . . . . . 20
11.0 Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
12.0 Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
13.0 Repair . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
13.1 Front Wheel Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
13.2 Rear Wheel Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
13.3 Replacing/Removing the Back Upholstery . . . . . . . . . . . . . . . . . . 24
13.4 Replacing/Removing the Seat Upholstery . . . . . . . . . . . . . . . . . . 24
14.0 Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Page 3
User & Workshop Manual for the Lightning Upholstery
3
SAFETY RULES:
WARNING: Failure to follow these warnings and assembly instructions could result
in serious injury or death.
Immediately discard any plastic wrapping.
Never allow children to fold, assemble, or disassemble the Pushchair.
Do not go over the weight capacity for the Pushchair. Excessive weight may
cause a hazardous, unstable condition if the approved load is exceeded.
Never place child in Pushchair with their head forward and feet rearward.
Avoid serious injury from falling or sliding out.
Always use seat belt.
Never leave user unattended.
Never allow Pushchair to be used as a toy or allow children to give rides to others.
Never use Pushchair if it becomes damaged.
Always be aware of trafc around you when walking.
Always engage brakes when you stop or when you let go of handle.
Accessories or parcels placed in or on the Pushchair may cause it to become
unstable.
To avoid burns, never put hot liquids in the working tray.
Care must be taken when folding and unfolding the product to prevent nger
entrapment.
WARNING – RAINCOVER FOR LIGHTNING PUSHCHAIR
TO AVOID DANGER OF SUFFOCATION, RAINCOVER MUST BE ASSEMBLED WITH
OPTIONAL CANOPY AS PER ILLUSTRATION. DO NOT LEAVE USER UNATTENDED AT
ANY TIME.
WEIGHT LIMITATIONS
The weight specications were tested and approved in accordance to the below guidelines
LT11/LT11SE – Total Weight Capacity is 86lbs (39.0kg)
• 66lbs (30kgs) on the seat.
• 5lbs (2.3kgs) on left side wheel.
• 5lbs (2.3kgs) on right side wheel.
• 10lbs (4.5kgs) on the lower basket.
LT14/LT14SE – Total Weight Capacity is 120lbs (54.4kg)
• 100lbs (45.5kgs) on the seat.
• 5lbs (2.3kgs) on left side wheel.
• 5lbs (2.3kgs) on right side wheel.
• 10lbs (4.5kgs) on the lower basket.
LT16/LT16SE – Total Weight Capacity is 150lbs (68kg)
• 100lbs (45.5kgs) on the seat.
• 5lbs (2.3kgs) on left side wheel.
• 5lbs (2.3kgs) on right side wheel.
• 10lbs (4.5kgs) on the lower basket.
!
!
!
!
!
!
!
!
!
!
!
!
!
!
Page 4
User & Workshop Manual for the Lightning Upholstery
4
PUSHCHAIR FEATURES
LT11/LT11SE MODEL
HEAVY DUTY UPHOLSTERY
includes moldable ‘stays’
FRONT RIGGING
SWING AWAY, FLIP-UP
Adjusts in the areasextension, Fore & Aft,
angle & lateral
SEAT DEPTH
ADJUSTABLE
1” to 12”
[15” with
optional Kit]
FOOTREST EXTENSION
From 1” to 12” in 1” increments
standard.
LT14/LT14SE MODEL
HEAVY DUTY UPHOLSTERY
includes moldable ‘stays’
FRONT RIGGING
SWING AWAY, FLIP-UP
Adjusts in the areasextension, Fore & Aft,
angle & lateral
Width between
Arms 13 1/2”
Width between
Arms 16 1/4”
SEAT DEPTH
ADJUSTABLE
12” to 14”
[17” with
optional Kit]
FOOTREST EXTENSION
From 1” to 17” in 1” increments
standard.
Page 5
User & Workshop Manual for the Lightning Upholstery
5
LT11/LT14/LT16 MODEL (Both Edition)
PUSH HANDLE
[ For pushing & control
of chair ]
LOCKING STRAP
[ To hold in folded position ]
CARRYING HANDLE
7000 SERIES ALUMINUM
is used for aircraft structural
members because of its
superb strength to weight
properties
WHEEL LOCKS
[ Operates both sides with single actuation ]
FOLDING
ACTUATOR
PUSHCHAIR FEATURES
LT16/LT16SE MODEL
HEAVY DUTY UPHOLSTERY
includes moldable ‘stays’
FRONT RIGGING
SWING AWAY, FLIP-UP
Adjusts in the areasextension, Fore & Aft,
angle & lateral
SEAT DEPTH
ADJUSTABLE
16” to 18”
[21” with
optional Kit]
FOOTREST EXTENSION
From 1” to 17” in 1” increments
standard.
Width between
Arms 17 1/2”
Page 6
User & Workshop Manual for the Lightning Upholstery
6
PUSHCHAIR ACCESSORIES
CANOPY
Extended Length w/Angle for Increased
Protection Viewing Window
Red Item # Blue Item #
LT11-RCD LT11-BCD
LT14-RCD LT14-BCD
LT16-RCD LT16-BCD
HEEL LOOPS
& ANKLE CUFFS
Soft, Stretch Fabric For Comfortable,
Firm Hold
Item #
LT11-BAC
LT14-BAC
LT16-BAC
HARNESS COVERS
Washable & Easy to Add or Remove
Soft, Fleece Covers w/Lateral Wing
Red Item # Blue Item #
LT11-RHC LT11-BHC
LT14-RHC LT14-BHC
LT16-RHC LT16-BHC
WEATHER PROTECTOR
w/ Velcro Closures Custom Made for
the Lightning
Item #
LT11-RC
LT14-RC
LT16-RC
SINGLE FLAP
Adjustable Lateral Trunk Support
Red Item # Blue Item #
LT11-RSF LT11-BSF
LT14-RSF LT14-BSF
LT16-RSF LT16-BSF
DOUBLE FLAP
Adjustable Lateral Trunk Support w/
Double Pads
Red Item # Blue Item #
LT11-RDF LT11-BDF
LT14-RDF LT14-BDF
LT16-RDF LT16-BDF
HEADREST EXTENSION
Simple Add-On or Remove
Design Adds 6” of Height
Red Item # Blue Item #
LT11-RHRE LT11-BHRE
LT14-RHRE LT14-BHRE
LT16-RHRE LT16-BHRE
HEADREST
Padded, Contoured w/Lateral Wings
Red Item # Blue Item #
LT11-RHR LT11-BHR
LT14-RHR LT14-BHR
LT16-RHR LT16-BHR
WORK ‘N’ PLAY TRAY
w/Turn-Up or Down Sides Easy to
Remove & Position
Item #
LT11-WT
LT14-WT
LT16-WT
TRANSPORTATION TIE DOWN
KIT
Item #: LT-TD
Navy Blue
Red Glow
UPHOLSTERY COLORS:
All accessories are
available in two colors.
Page 7
User & Workshop Manual for the Lightning Upholstery
7
SPECIFICATIONS CHART
Specications 11” Model 14” Model 16” Model
SEAT WIDTH
OUTSIDE CANES
12.75” 15.75” 16.75”
SEAT WIDTH
BETWEEN CANES
11” 14” 16”
OVERALL HEIGHT
PUSH HANDLE HEIGHT
36” 36” 38”
OVERALL LENGTH w/ FOOTPLATE
38” 42” 44”
OVERALL LENGTH w/o FOOTPLATE
31” 35” 37”
LENGTH WHEEL TO WHEEL
(maximum)
27” 27” 27”
SEAT TO FLOOR
20”@11” depth 21”@14” depth 22”
OVERALL WIDTH
19.5” 24” 25”
SEAT ANGLE (DUMP)
30° 30° 30°
BACK UPHOLSTERY
19.25” 24” 24.75”
SEAT TO FOOTREST *
1” to 12” 1” to 17” 1” to 17”
BACK ANGLE SETTINGS
85°, 90° & 95° 85°, 90° & 95° 85°, 90° & 95°
FOLDED DIMENSIONS
19.25”W x 19.25”D x 25.5”H 24”W x 19.25”D x 27.5”H 25”W x 16”D x 28”H
WEIGHT OF CHAIR
(without riggings)
25 lbs 27 lbs 28 lbs
WEIGHT CAPACITY
75 lbs 100 lbs 150 lbs
FRAME COLOR CHOICES
SILVER SILVER SILVER
UPHOLSTERY COLOR CHOICES
NAVY BLUE • RED GLOW NAVY BLUE • RED GLOW NAVY BLUE • RED GLOW
FRONT WHEELS
6” 6” 6”
REAR WHEELS
10” 10” 10”
HEADREST EXTENSION
ADDS 6” OF HEIGHT ADDS 6” OF HEIGHT ADDS 6” OF HEIGHT
WIDTH OF BACK SEAT
(tube to tube)
11” (outside - 12.75”) 14” (outside - 15.5”) 15” (outside - 16.75”)
SEAT TO TOP OF BACK
20.25” (upholstery)
25” to handle
24” (upholstery)
25” to handle
25” (upholstery)
28” to handle
FOOTPLATE
7.25” x 5.4375” 7.25” x 5.4375” 7.25” x 5.4375”
FOOTPLATE ADJUSTMENT
(fore and aft)
2” 2” 2”
FOOTPLATE MOUNTS
(outside width)
15.75” 16” 17”
WIDTH BETWEEN ARMRESTS
13.5” 16.25” 17.5”
SEAT DEPTH
10” to 12” 12” to 14” 16” to 18”
TUBING
7/8” 7/8” 7/8”
OVERALL LENGTH W/O RIGGINGS
26.5” 29.5” 34”
*(Standard extension range in 1” increments) • Note: The Lightning has been crash tested
Page 8
User & Workshop Manual for the Lightning Upholstery
8
1.0 INTRODUCTION
This Owners Manual will outline the proper method and easy
handling of the Lightning Pushchair and gives instructions for the
required cleaning and maintenance.
To avoid damage caused by improper handling and to allow optimal
use of the Lightning Pushchair, please read the following instructions
thoroughly.
If you have further questions or problems, please contact your
healthcare provider.
2.0 CONTACT COMPANY FOR ANY CONCERNS
For Europe, contact the authorized representative below:
TENDERCARE LIMITED
P.O.BOX 3091 LITTLE HAMPTON, BN16 2WF
UNITED KINGDOM
PH: #44 (0) 1903 726161 FX: #44 (0) 1903 734083
3.0 INTENDED USE – RECOMMENDATIONS
(Source: Catalogue and index for orthopedic appliances of the health
insurance companies, FRG) Rehab buggies are indicated for the
transport of patients with severe disabilities – mainly children and
adolescents – who are unable to walk and or to move independently
in a wheelchair.
4.0 DECLARATION OF CONFORMITY
Stealth Products declares that this product conforms to the requirements
of the 93 / 42 / EEC Guidelines.
5.0 UNPACKING AND PREPARING THE PUSHCHAIR FOR USE
The original package contains the following components
Pushchair (folded)
Footrest Riggings (both Left & Right)
Owners Manual
Accessories as Ordered
After unpacking and checking you have all components and that they
are in good condition, carefully dispose of the packaging at your local
recycling centre.
6.0 FOR UNFOLDING THE PUSHCHAIR, PROCEED TO THE
FOLLOWING INSTRUCTIONS:
• Remove any transport straps or transport guards
• Grasp the Pushchair at the push handles and lift up.
• Lift up enough as to allow the left and right locking mechanism to
latch in place.
Page 9
User & Workshop Manual for the Lightning Upholstery
9
7.0 SETTING UP AND ADJUSTING THE PUSHCHAIR
7.1 Folding and Carrying
• Grasp the Pushchair handles with
both arms, and depress the folding
locking mechanism with foot.
• Hold in the down position and push
the back forward toward the seat.
• Place the left side of the Pushchair
on the oor.
• On the right side, maneuver the
Velcro strap around the armrest and
fastened to the back of the chair.
• With care, pick the Pushchair up
using the plastic handle.
Illustration of the Pushchair in its
correct folding set-up.
Page 10
User & Workshop Manual for the Lightning Upholstery
10
7.2 Seat Back Angle Adjustment
To adjust back angle, you must remove
back upholstery
• Remove the top Velcro strap.
• Remove the lower Velcro strap.
• Remove both left and right side
backrest tubes.
• The diagram to the right will show
three position adjustments.
position 1 = 95
position 2 = 90
position 3 = 85
Page 11
User & Workshop Manual for the Lightning Upholstery
11
7.3 Seat Depth Adjustment
• Using a 10mm wrench, remove the
adjustment nut on both sides.
• Move to the desired angle position
and fasten the nuts with the 10mm
wrench.
• LT16 Adjustment = 16”-18” (406.4-457.2mm)
• LT14 Adjustment = 12”-14” (304.8-355.6mm)
• LT11 Adjustment = 10”-12” (254-304.8mm)
• Press release button and move For or
Aft for desired depth adjustment.
Page 12
User & Workshop Manual for the Lightning Upholstery
12
The footrest will swing-away for easy use
and adjustment.
• Swing footplate out.
7.5 Footplate Adjustments
• LT16 = 1”-17” (25.4-431.8mm)
• LT14 = 1”-17” (25.4-431.8mm)
• LT11 = 1”-12” (25.4-304.8mm)
• Remove the locking pin.
• Move the footrest to the desired
height location.
• And replace the locking pin.
• Using a 10mm wrench, loosen the
bolts and move to desired location.
• Once desired location is achieved,
fasten both bolts before use.
7.4 Footrest Height Adjustment
Page 13
User & Workshop Manual for the Lightning Upholstery
13
7.6 Adjusting and Using the Safety Harness
Adjusting the depth on the Crotch Strap
• With the button facing up, guide the
strap through the mid section of the
holder.
• Then guide the strap under and
over the crotch strap ring.
• Finally, adjust the strap to the desired
length and tighten the strap down.
Adjusting the depth on the Crotch Strap
• Remove both hand nuts from the back
of the Pushchair.
Page 14
User & Workshop Manual for the Lightning Upholstery
14
• On the front of the Pushchair, remove
the top strap pins and place them
where needed.
• Once desired location is met,
replace both hand nuts and rmly
tighten.
Locking and unlocking the safety harness
• To lock, insert both left and right side
harness pins into push button slots.
• To unlock, press the “red” push button
and gently pull back.
To engage brake
• With your foot press the brake lever
down. This will lock both rear wheels.
To disengage brake
• With your foot placed under the brake
lever, pull the lever up. This will unlock
both rear wheels.
7.7 Brake System
Page 15
User & Workshop Manual for the Lightning Upholstery
15
8.0 INSTALLING ACCESSORIES
8.1 Headrest Extension
• Insert the headrest extension rods
into the backrest accessory tubes.
• Insert the canopy into the backrest
accessory tubes or (if headrest
extension is in place) insert into
headrest extension tube.
The headrest extension is required for
installation of the headrest pad.
• From the headrest, tie the loose strings
strings onto the headrest extension.
• Guide the Velcro strap through the
loop and fastened it to other side of
the strap.
8.2 Canopy
8.3 Padded Headrest
Page 16
User & Workshop Manual for the Lightning Upholstery
16
• Wrap cover around the harness straps
and fasten one side of the Velcro to the
other.
8.5 Padded Harness Covers
• Guide the screw from the ankle cuff
through the top of the footrest.
• On the bottom of the footrest, place
the washer and fastened the nut.
8.4 Heel Loop and Ankle Cuffs
Page 17
User & Workshop Manual for the Lightning Upholstery
17
8.6 Trunk Support
• Place the trunk support on the front
of the Pushchair and fasten it around
the back set using the Velcro straps.
• On both sides, wrap the bottom
support ap Velcro straps around
the lower armrest tube.
• Using the loose strap, guide it
through both top support ap rings.
• Finally, guide the strap through its
own ring and wrap around behind
the lower supports aps.
Page 18
User & Workshop Manual for the Lightning Upholstery
18
9.0 INSTRUCTIONS FOR TRANSPORTING THE LIGHTNING
PUSHCHAIR
The Lightning Pushchair can be folded for transport in the luggage area
of the vehicle. The Lightning Pushchair has been successfully impact
tested and meets the requirements specied in ANSI/RESNA WC/Vol.1,
Section 19, 5.3., prior to May 2002. It may therefore be used as a vehicle
seat.
CAUTION: When used as a vehicle seat the following instructions must
be followed.
WARNING: ONLY A COMPETENT PERSON SHOULD INSTALL THE TRANSPORTATION
DEVICES
9.1 Preparing Lightning For Transport
9.1.1 Check that the child is correctly strapped in the seat using the
5-point harness. Check that the 5-point harness is properly adjusted.
9.1.2 During transportation the headrest extension must be tted.
9.1.3 Remove the following if tted: Work “N” Play Tray, Rain-hood,
Shopping Basket or Sun Canopy.
9.2 Attach The Set Of 4 Tie-Down Kit Brackets
This Instruction is specic to the attachment of Tie-Down hardware for the Lightning
Pushchair.
WARNING: FAILURE TO ATTACH THE HARDWARE AS DETAILED COULD LEAD TO
SERIOUS INJURY OR DEATH.
9.2.1 TOOLS
• 3/16” T-handle Allen.
9.2.2 CONTENTS
4 - Tie-Down assemblies and each include:
• 1 - Handle Threaded Clamp (HTC).
• 1 - Through Clamp (TC).
• 4 - 1/4-20 x 3/4” Socket Head Cap Screws
9.3 Assembly Instructions
9.3.1 Separate the 4 TCs from the HTCs by removing the four screws.
9.3.2 Apply adequate amount of Loctite to each screw.
9.3.3 Loosely position the HTC and the TC to the front left and right bars
as shown:
• LT14 & LT16 - (Fig. 1)
• LT11 - (Fig. 2)
9.3.4 Loosely position the HTC and the TC to the rear left and right bars
as shown:
• (Fig. 3)
9.3.5 Tighten all clamp screws to 100 inches pounds torque (metric: 11Nm).
Page 19
User & Workshop Manual for the Lightning Upholstery
19
9.4 Attach The Lightning Pushchair To Vehicle
The Lightning must be attched to the vehicle using the Set of 4 Tie-Down
Brackets, and a 4-point wheelchair restraint with Karabiners.
Note: The Set of 4 Tie-Down Kit Brackets is available from
Tendercare Ltd. 4-point wheelchair restraints are manufactured
by Unwin Safety Systems.
• Position the assembly correctly in
the vehicle over the oor track with
the front of the Lightning facing
towards the front of the vehicle (in
the direction of travel).
Put the Brakes on.
• Attach the front restraints to the
oor track and the front Tie-Down
Brackets making sure they are in
line with the oor track. Attach the
rear restraints to the oor track and
the rear Tie-Down Brackets.
• Open the lever of the over centre
buckle and pull through the excess
webbing to tighten the belt. Snap
down lever to tension.
• To release the Lightning follow the
above instructions in reverse order.
(Fig. 3)
Rear View 11”, 14” & 16”
Through
Clamps
HandleThreaded
Clamps
(Fig. 1) Front View
14” & 16” Pushchair
(Fig. 2) Front View
11” Pushchair
Through
Clamps
Page 20
User & Workshop Manual for the Lightning Upholstery
20
10.0 INSTRUCTIONS FOR ATTACHING THE WORK ‘N’ PLAY TRAY
The below instructions are for attaching the Work ‘n’ Play tray to the
Lightning Pushchair.
CAUTION: THE TRAYS HAVE BEEN RATED TO HOLD UP TO 6.8kgs
15lbs OF WEIGHT. DO NOT OVERLOAD.
WARNING: REMOVE THE TRAY WHEN TRANSPORTING USER IN A
MOVING VEHICLE.
10.1 Contents
• Plastic Tray
• 2 Locking Pins
10.2 Attaching And Removing The Tray
10.2.1 Place the tray on top of the armrest handles as shown on Fig. 1.
10.2.2 Insert a locking pin to both sides as shown on Fig. 2.
10.2.3 For removal, ensure that the tray is free from objects and release
the tray by removing both locking pins.
11.0 CLEANING
11.1 Frame
11.1.1 To clean the frame, wipe with a damp cloth and dry thoroughly.
11.1.2 For more stubborn stains wipe with a damp cloth and warm water.
in which a little mild soap has been dissolved. Dry thoroughly.
11.1.3 Never use furniture polish or any spirit to clean the frame.
11.2 Upholstery
11.2.1 Remove the seat and back upholstery from the Pushchair.
11.2.2 Remove the harness and support boards from the upholstery.
11.2.3 Machine wash in cold water on delicate cycle.
11.2.4 Dry cover thoroughly before re-assembly. Do not tumble dry.
11.3 H-Harness
11.3.1 Remove harness from Pushchair.
11.3.2 Wipe with a damp cloth and dry thoroughly. Do not tumble dry.
11.3.3 Do Not immerse in water or wash in a machine
Fig. 1 Fig. 2
Page 21
User & Workshop Manual for the Lightning Upholstery
21
11.4 Accessories
11.4.1 Remove accessories from the Pushchair.
11.4.2 Wipe with a damp cloth and dry thoroughly.
12.0 MAINTENANCE
Excessive exposure to the sun or heat could cause fading or warping
of parts.
Should a problem be found when carrying out the regular checks, it should be
immediately reported to the issuing authority or Tendercare Ltd.
12.1 Routine Maintenance -
The users family can carry-out the following tasks. No tools required.
12.1.1 Always wipe the Pushchair dry. Never put it away damp. (daily)
12.1.2 Check operation of the brake, folding and reclining mechanisms (weekly).
12.1.3 Check condition of harness, stitching and buckle (weekly).
12.1.4 Clean frame when necessary (we suggest at least once a week).
12.2 Six Months Maintenance -
Someone who is a competent tradesman or repairer should only carry out this
work. If a major fault is found stop using the Pushchair until it has been corrected.
12.2.1 Fold and open the Pushchair. Check that all movements through the
folding range are free. Examine frame for any damage.
12.2.2 Examine upholstery and foot straps for wear and arrange for replacement
if necessary.
12.2.3 Examine nuts, bolts, pivots and frame plugs for tightness and general
condition
12.2.4 Examine brake assembly for wear, damage and correct operation.
12.2.5 Examine tires for sharp objects, cuts or splits.
12.2.6 Examine castor and wheel bearings and suspension for excessive wear.
12.2.7 Check castors and rear wheels for free rotation, security and accumula-
tion of uff and grit. Remove with a dry lint free cloth.
!
!
Page 22
User & Workshop Manual for the Lightning Upholstery
22
13.0 REPAIR
Any items involved in an accident no matter how minor MUST BE
WITHDRAWN FROM SERVICE IMMEDIATELY AND REPLACED.
Key Points:
Do not reuse Nyloc nuts. Always replace with a new Nyloc nut.
Always use recommended components and parts available from
Tendercare Ltd.
Do not modify or repair frame
13.1 Front Wheel Assembly
!
!
!
• Insert the shoulder bolt from
outside the wheel caster, and
• Through the wheel, and
• To the inside wheel caster.
• Place the washer and nut on
the inside of the wheel caster.
• Then, tighten with necessary
tooling wrenches.
• Required items:
Wheel
Nut
Washer
Shoulder bolt
10mm wrench
Page 23
User & Workshop Manual for the Lightning Upholstery
23
13.2 Rear Wheel Assembly
• Required items:
Wheel
Nut
Washer
Shoulder bolt
10mm wrench
• Insert the shoulder bolt from the
outer part of the wheel
• Through the wheel, and
• To the inside wheel mount.
• Place the washer and nut on
the inside of the wheel caster.
• Then, tighten with necessary
tooling wrenches.
• Place the washer and nut on the
inside of the wheel mount.
• Then, tighten with necessary
tooling wrenches.
Page 24
User & Workshop Manual for the Lightning Upholstery
24
To replace the back upholstery,
• Remove the top Velcro strap.
• Remove the lower Velcro strap.
• Remove both left and right side backrest
tubes.
• Slip the upholstery out of the tubes.
• For reassembly, follow steps in reverse
order.
To replace the seat upholstery,
• Press both depth release buttons.
• Slide seat tubes out of tube receiver.
• Unscrew both bolts from the seat tubes.
• Slide upholstery from seat tubes.
• For reassembly, follow steps in reverse
order.
13.4 Replacing/Removing Seat Upholstery
13.3 Replacing/Removing the Back Upholstery
Page 25
User & Workshop Manual for the Lightning Upholstery
25
14.0 WARRANTY
For UK warranty claims contact Tendercare Ltd #44 (0) 1903 726161.
For all other warranty claims contact issuing authority.
14.1 The above will repair or replace free of charge, any parts or part found
to be defective due to manufacturer within a period of 12 months from
the date of delivery.
14.2 The above will not repair or replace free of charge any part or parts found
to be defective due to abuse, misuse or lack of correct maintenance.
14.3 Equipment for warranty claims should be returned in a strong carton.
There may be a charge for collection.
Page 26
P.O. Box 458 103 John Kelly Drive Burnet, TX 78611
phone: 1(800)965.9229
fax: 1(800)806.1225
e-mail: info@stealthproducts.com
www.stealthproducts.com
Loading...