Stanley Healthcare Bed-Check Classic-Check Fall Risk Monitoring System User Guide User Guide

Classic-Check

Bed-Check®Sensormat

User Manual

0163-436-C

Before installing this system, please read and follow these instructions carefully. Failure to do so could result in injury or death. No device is a substitute for proper nursing care.

CAUTION

Table of Contents

Quick Start Procedures ......................................................................................... 2

(For the experienced Bed-Check

caregiver, no setting changes)

Quick Set Procedures ............................................................................................ 3

(For the experienced Bed-Check

caregiver making setting changes)

How To Use the System ........................................................................................ 4

(Complete detailed instructions) Sensormat

............................................................................................... 4

Interfacing with the Nurse Call System ................................................... 6

System Operation..................................................................................... 8

Changing Operational Parameters (Setting) .......................................... 10

Troubleshooting .................................................................................................. 13

Care and Maintenance ........................................................................................ 14

Warranty Information ........................................................................................ 15

Read and follow these Installation instructions, particularly the warnings and cautions, before using your Bed-Check

Classic-Check®system. Failure to do

so may result in injury or death.

The Classic-Check

system will not stop a person from leaving a bed, chair, wheelchair or room. It is intended only to alert a caregiver that a person may need assistance. Other interventions may still be required for some people.

The Classic-Check

system can be defeated by a cognitively aware person, a person with only a few moments of lucidity or an uncooperative person. Properly assess each individual before the Classic-Check

system is used.

Make sure you have thoroughly read and understand the Classic-Check

system

instructions before using the Sensormat

Stanley Healthcare makes no claims whatsoever as to the viability of using nonBed-Check

brand pressure sensitive pads with the Classic-Check®control unit and accepts no responsibility or liability for any negative outcomes of any sort that arise from this action.

Visual monitoring by caregivers is required. Bed-Check

Sensormats®may not be suitable for all high risk persons; restraints may be required for some people.

Test your Sensormats

and Classic-Check®monitor before each use. Make sure

your Classic-Check

monitor is working properly. If the Sensormats®are no

longer working, discard them immediately.

During any HOLD mode (any yellow light), the system will not alarm. It will either remain on HOLD if no weight is on the mat, or begin to monitor after the time intervals cited above if weight is back on the mat. Any time a patient is on the Sensormat

, you may bypass the wait and begin monitoring immediately by pressing RESET. Always verify that the green light (MONitor mode) is blinking before leaving the patient.

Always physically inspect the status of the control unit by viewing the illuminated indicators on its face before leaving the patient’s room. If the control unit is in either hold mode, press the reset button to immediately begin monitoring and then ensure that the green monitor light is flashing. There is a possibility of the patient exiting the bed or chair during either HOLD period.

WARNING

Use of the Bed-Check® Classic-Check® system simultaneously with telemetry monitoring systems may, in some instances, result in detectable artifacts on the telemetry monitor recording. The Classic-Check's electronic monitoring cycle has been adjusted to minimize the occurrence of detectable artifacts; however, because of their sensitive nature, telemetry monitoring systems may detect the Classic-Check system. If an unexplained artifact is noted on the telemetry monitor recording, repeat the test with the Classic-Check system unplugged to clarify whether or not it is the source of the artifact.

CAUTION

Quick Start Procedures

How to get started with no setting changes - for the experienced Bed-Check

Caregiver.

Do use this section if you already understand the basic operational procedures, and the present settings do not need to be changed. Do not use this section

if you are unfamiliar with this equipment or wish to change

settings. Please refer to other sections of this User Guide. See Table of Contents.

Current Settings:

If brand new, the factory set delay is 3 seconds, Day mode, “Low pitch warble” alarm tone, maximum Day Volume and minimum Nite Volume. If the unit has already been in service, the settings will be as last selected, whether or not power has been interrupted since then.

Action step is in normal type. System indications are in Italics.

Set up:

1. Install and connect the Sensormat

2. Plug in the power cord. Unit will beep twice with solid yellow (Idle HOLD).

3. Plug in the nurse call system cord, if used, with an adapter if needed.

Monitoring patient/resident:

4. Place the patient on the mat. Flashing yellow for 5 seconds (or push RESET to

bypass and monitor immediately), then blinking green.

Repositioning or removing patient/resident:

5. Push RESET (middle button). Flashing yellow light (temporary HOLD) for 25 seconds. Classic-Check

then automatically goes back to MONitor mode (blinking

green) if weight is sensed on the Sensormat

, or idle HOLD (steady yellow) if no

weight is sensed.

6. Any time weight is on the Sensormat

, start immediate monitoring by pressing

RESET.

Shutting off alarm:

7. Press RESET. Flashing yellow (temporary HOLD) for 25 seconds, then steady yellow (idle HOLD) if no weight is on the mat, or blinking green light (MONitor) if

weight is on the mat.

Day/nite Mode change (either way)

8. Press DAY/NITE button once. DAY mode, no light in splash shield. NITE mode, blue in splash shield.

Assure that the green MONitoring light is blinking before leaving the patient. The system will not alarm while in any HOLD mode (yellow light blinking or on).

CAUTION

Quick Set Procedures

How to change settings - for the experienced Bed-Check®Caregiver.

Best done holding the unit with both hands and using both thumbs to press buttons. We recommend setting volumes after setting the tone. Classic-Check®remembers its current setting after power interruptions.

Actions are in standard type. Classic-Check

indications are in italics.

DAY/NITE mode change

1. Press/release the DAY/NITE button. Blue light in the splash shield indicates NITE

mode.

ALARM tone check (Tone will be identical in DAY and NITE modes.)

1. Press/hold RESET, press/release ALARM, release RESET (hear present alarm tone).

2. To silence, press/release RESET again (silence).

ALARM tone change (10 settings. Tone will be the same in both DAY and NITE modes.)

1. Press/hold RESET, press/hold ALARM. Do not release either yet.

2. Continue to hold down ALARM but release RESET (hear present alarm tone).

3. While still holding down ALARM press/release RESET. Each time you do this, unit will sequence to the next tone setting. Repeat until you hear desired tone.

4. When desired setting is reached, release ALARM button.

5. Press/release RESET once more to silence and lock in setting (silence).

6. Summary: The motion is hold middle, hold right, release middle. Press/release middle repeatedly to select a tone. Release all, press/release middle once more to lock.

VOLUME check

1. Set to DAY mode to check day volume or NITE mode to check night volume.

2. Press/hold RESET, press/release VOLUME, release RESET (hear present tone).

3. To silence, press/release RESET again (silence).

VOLUME change (7 separate settings available each for DATE and NITE modes)

1. Set to DAY mode to set day volume or NITE mode to set night volume.

2. Press/hold RESET, press/hold VOLUME. Do not release either yet.

3. Continue to hold down VOLUME, release RESET (hear present volume).

4. While still holding down VOLUME, press/release RESET. Each time you do this, unit will sequence to the next volume setting. Repeat until you hear desired volume.

5. When desired setting is reached, release VOLUME button.

6. Press/release RESET once more to silence and lock in setting

(silence).

7. Summary: The motion is hold middle, hold left, release middle. Press/release middle repeatedly to select a volume. Release all, press/release middle once more to lock.

DELAY change (1,2 or 3 seconds. Setting will be the same for DAY and NITE modes)

1. The red LEDs marked 1 2 3 indicate the current DELAY setting.

2. Press/release ALARM/DELAYto change the setting.

How To Use The System

(Complete detailed instructions)

The Classic-Check®System consists of a control unit and a disposable pressure sensitive Sensormat®, available in several sizes either for use on a standard hospital bed or a bedside chair. When the patient’s weight is off the Sensormat®for a pre-selected number of seconds, the control unit activates two alarms (if selected): a call signal at the nursing station and an audible alarm in the patient’s room. The nurse, having been alerted that a patient is attempting to exit the bed, should immediately send or render assistance. The patient may simultaneously be counseled by intercom if available. NOTE: The alarm unit should be positioned outside of the patient’s reach to prevent tampering with alarm settings.

Sensormat

To ensure effectiveness, place the Sensormat®across the width of the bed, ON TOP OF THE MATTRESS. The preferred Sensormat®location is directly under the patient’s buttocks three to five inches below the bend in the mattress when the head of the bed is elevated. Effective operation of the Sensormat

in the alternative location, behind the patient’s back, is dependent upon their weight and the articulation angle of the bed.

To prevent slipping and to maintain the correct position of the Sensormat

, always use the enclosed rubber bands and metal clips. A. Thread one end of the band through the hole of the clip to form a loop. Pass the other end of the band through the loop and pull tight to form a knot at the base of the clip. B. Thread the other end of the band through the Sensormat

hole to form a loop. Bring the clip through the loop and pull tight to form another knot at the end of the Sensormat

. Repeat these

steps on the other end of the mat. C. Position Sensormat

across width of bed 3

inches to 5 inches below bend in mattress so it will be under the patient’s buttocks. D. Attach the clips to the piping at the bottom of the mattress on both sides of the bed or to the bed frame. The idea is to have the rubber bands taut so the Sensormat

does not

slide back and forth over the mattress. E. You may place over the Sensormat®a felt or incontinence pad, towel, draw sheet, rubber sheet, sheep skin or convoluted foam pad. Make the bed as usual.

Nursing personnel should test the system’s effectiveness daily when either Sensormat

position is selected. Sensormats®may not be effective with air bed

type mattresses; test before using.

WARNING

The Sensormat®is effective for patients weighing 100 pounds or more. For patients weighing under 100 pounds, test the effectiveness immediately upon installation with the patient in bed. Please be aware that the physiology of each patient is different. The functionality of the Sensormat

is impacted by the

physics of the patient’s weight and height.

Plug the Sensormat

cord connector into the side of the control unit (Port designated “Sensormat®”). Sensormats®are available with 5 1/2 foot and 8 foot cords. If you are using the wire holster with control unit, 5 1/2 foot cords work best. Other cord lengths may be special ordered.

Nursing personnel should test the system daily for proper functioning. If the patient weighs 100 pounds or more, the nurse may test the system using just hand pressure on the Sensormat

. Lighter weights could possibly compromise system performance, and if the patient weighs less than 100 pounds, system function should be checked using the actual patient’s presence in the bed. If the system does not perform properly, trying a different Sensormat

may resolve the

problem.

To ensure compatibility, the Classic-Check®control unit should be used only with Bed-Check

Sensormat®pressure sensitive mats. An alarm may sound when a damaged or incompatible mat is plugged into the control unit. The power supply must be unplugged from the wall to cancel the alarm.

Always physically inspect the status of the control unit by viewing the illuminated indicators on the face of the control unit before leaving the patient’s room. If the control unit is in either HOLD mode, press the reset button to immediately begin monitoring and ensure the green monitor light is flashing. There is a possibility of the patient exiting the bed or chair during either HOLD period.

WARNING

Interfacing with the Nurse Call System

The Classic-Check®can be set for a normally open or normally closed nurse call system. The unit is factory preset to function with a normally open system.

The Control Unit uses a standard, two conductor, 1/4 inch diameter phone plug, the most common type of nurse call connection. If your nurse call system does not provide a compatible input, contact Bed-Check

or your biomedical depart-

ment to obtain the appropriate adapter.

If your facility does not have a biomedical department, please contact BedCheck

at the phone number listed on the back of this user guide. If requesting information on interfacing the Control Unit to a nurse call system, please have the following information available:

• The brand of your nurse call system.

• Adescription of the system’s call cord or pillow speaker, including the type of plug and number of pins in the plug.

• Whether your nurse call system is normally open or normally closed.

• If this information is not available, you may still contact us for assistance, and we will be glad to help you.

The Classic-Check (72021) is supplied with a ¼" receptacle/jack (which may be used in lieu of a common Y-Adaptor) to accept a common ¼" mono plug from any other equipment in use in the patient's room. This receptacle/jack is located in the housing for the ¼" mono plug supplied on the end of the 72021 nurse call cord.

However, common ¼" mono plugs from other equipment in the patient's room are not all exactly alike. Therefore:

TEST THIS CONNECTION BEFORE USE TO VERIFY THAT THE 1/4” PLUG ON THE OTHER EQUIPMENT IS FULLY COMPATIBLE WITH THE 1/4” RECEPTACLE IN THE 72021 AND THAT THE EQUIPMENT’S TEST CALL IS SUCCESSFULLY RECEIVED BY YOUR NURSE CALL SYSTEM.

IF THE TEST CALL IS NOT SUCCESSFUL, DO NOT

USE THIS INCOMPATIBLE

RECEPTACLE IN THE 72021 WITH THAT EQUIPMENT.

WARNING

Possible Internal Set-up Instructions

(only if connecting to a nurse call system)

1. Determine if your nurse call system is a normally closed or normally

open system (consult your BioMed). The Classic-Check

Unit is factory

set for a normally open system unless otherwise specified.

2. If your system is normally open, or if your Classic-Check®Unit was

ordered to be specifically compatible with your system, skip the rest of this section. Continue on to the section entitled How to Use the System on page 4.

NOTE: The following steps (3 Thru 8) should be accomplished only by your BioMed Department or Bed-Check

3. With the Classic-Check

Unit unplugged, remove the 4 screws from the

back of the case.

4. Remove splash guard and the back cover.

5. At JP1 remove jumper.

6. Re-install the jumper on pins 2 & 3 for normally closed (1 & 2 is for

normally open).

7. Reinstall the 4 screws. The round-headed screws fit the splash shield, and

the countersunk screws secure the bottom of the case. Do not over-tighten.

Danger of electrical shock. Unplug unit before servicing.

WARNING

Classic-Check®plugs into Nurse Call system

System Operation

The Classic-Check®Unit is factory set for a 3 second delay, day mode, “Low pitch warble” alarm tone, maximum day volume and minimum night volume.

1. Power up the Classic-Check

Unit by plugging the power cord into a standard (120 VAC) outlet. The unit will respond by giving a short two beep "Hello" signal.

2. If connecting to a nurse call system, plug the Classic-Check

Unit nurse

call cord into the system. The Classic-Check

Unit will function whether

or not connected to a nurse call system.

3. The yellow HOLD light and SECONDS ALARM lights will illuminate.

The Classic-Check

Unit powers up in idle HOLD, with a steady yellow

HOLD light and the red lights indicating the delay setting of 1, 2 or 3 seconds. This is the best time to make operational parameter changes, since the patient is not yet on the mat. See the section entitled Changing

Operational Parameters on page 10 for more information.

4. If you have not already done so, install the Sensormat

on the bed or

chair, and plug its cord into the Classic-Check®Unit. The yellow HOLD light should not blink either alone or with the delay lights. If it does, replace the Sensormat

5. The Classic-Check

Unit will stay in idle HOLD (steady yellow) until

further action is taken.

6. If weight is sensed on the Sensormat

, the Classic-Check®Unit will go to

short HOLD (blinking yellow) for 5 seconds. During those 5 seconds, if weight is again removed, the Classic-Check®Unit will revert to idle HOLD (steady yellow). If weight is still sensed after 5 seconds, the Classic-Check

Unit automatically begins to MONitor (green, blinking).

This reduces false alarms while relocating a patient, but also allows for

automatic monitoring that cannot be "forgotten" (no activate switch has to be pressed).

7. In the MONitoring mode, proper operation is indicated by the green MON light, which will blink off briefly, once per second.

8. When pressure (weight) is removed from the Sensormat®(patient begins to exit the bed or chair), the Classic-Check®Unit begins the delay countdown. Once the countdown starts, weight back on the Sensormat

will stop the countdown and MONitoring will resume. This reduces false alarms. However, once the alarm starts, it can only be silenced by pressing RESET. Weight back on the Sensormat®will stop countdown/resume MONitoring, but will not silence an alarm once that alarm has started. This is important for patient safety, and provides good feedback to the caregiver about patient agitation.

9. Pushing RESET while either MONitoring (before removing the patient) or when silencing an alarm puts the Classic-Check

Unit into a 25 sec

temporary HOLD (blinking yellow).

a. At 25 seconds, if weight is sensed on the Sensormat

, the Classic-Check®Unit automatically resumes MONitoring. If weight is not sensed on the Sensormat®, the Classic-Check®Unit goes to idle HOLD (steady yellow).

b. Any time during the 25-second temporary hold period, MONitoring

can be resumed without waiting by pressing RESET, as long as there is weight sensed on the Sensormat

10. Any time the Classic-Check®Unit is in the idle HOLD (steady yellow), if weight is again sensed on the Sensormat®, The Classic-Check®Unit will go to short HOLD (5 seconds).

a. At 5 seconds, if weight is sensed on the Sensormat

, the Classic-

Check

Unit automatically resumes MONitoring. If weight is not

sensed on the Sensormat

, the Classic-Check®Unit reverts to idle

HOLD (steady yellow).

b. The 5-second period may be bypassed and MONitoring is resumed

without waiting by pressing RESET at any time, as long as weight is sensed on the Sensormat

Summary:

• The Classic-Check®Unit will only start the delay countdown/alarm sequence when in the MONitor mode and weight is removed from the Sensormat®.

• In any HOLD mode, the Classic-Check

Unit will not alarm. It will either

remain in HOLD or automatically begin MONitoring when weight is again sensed on the Sensormat®(after the described time period).

Changing Operational Parameters

Day/Night Mode Setting

The Classic-Check®Unit has a blue light in the clear splash shield that illuminates in the NITE mode. In addition, you may pre-set the alarm volumes separately for DAY and NITE modes. (See the section entitled Volume Settings.) Press the DAY/NITE VOLUME button to select the mode desired. The blue light indicates NITE mode. (To bypass this feature and use the blue light to locate unit or verify power, set DAY/NITE volumes the same and select NITE.)

Delay Setting

When the Classic-Check®Unit is MONitoring (green light), ALARM DELAY is the time from pressure off the Sensormat®until the alarm begins. The

ALARM DELAY may be set for 1, 2 or 3 seconds by pressing the ALARM DELAY button and observing the red LEDs. ALARM DELAY may be reset at

any time when the Classic-Check

Unit is not in 5 second hold, countdown or alarm. One second is strongly recommended if monitoring a patient in a bedside chair or wheelchair, since he/she is poised to get up. 2 or 3 seconds are usually better for bed patients. Shorter delays may increase alarm frequency for restless bed patients, but may be necessary for “fast exit” patients.

Alarm Tone Settings

(If you do not wish to change the tone setting, skip to the Volume Settings section). There are ten available alarm tone settings. Six of them are songs, to provide a sound distinctly different from other equipment in the vicinity. The programmed songs have been selected for their non-threatening nature, while maintaining alarm effectiveness. The tone selected will be the alarm in both DAY and NITE modes, although volumes may be set separately.

Front Panel of Classic-Check

1. To hear the current alarm tone setting,

a. Press and hold RESET. b. Press and release ALARM DELAY.

c. Release RESET. You will hear the current tone setting. Silence by pressing RESET. Note that the volume may be wrong at this point, but it is best to set volume after the tone has been selected. Alarm tones are always played at lowest volume during alarm tone selection regardless of Day/Nite or volume settings.

d. If this is the tone desired, press RESET once more, skip the rest of

this section, and proceed to VOLUME SETTINGS.

2. To change the tone setting,

a. Press and hold RESET.

b. Press and hold ALARM DELAY.

c. Release RESET.

d. Continue holding ALARM DELAY and press/release RESET until

the desired alarm tone is reached. Each press/release of RESET advances the tone one step. If at the end of the list, the sequence will start over at 1.

e. For a visual indication of what setting you’re on, observe the 1

green and 3 red LEDs in a row.

Setting

❍ = off ● = on Tone

1 ❍❍❍● Low pitch warble

❍❍●❍ High pitch warble

❍❍●● Triple tone

❍●❍❍ Old McDonald Had a Farm

❍●❍● Mary Had a Little Lamb

❍●●❍ The Farmer in the Dell

❍●●● She’ll Be Comin’ ‘Round the Mountain

●❍❍❍ Tom, Tom, the Piper’s Son

●❍❍● Folk Song

●❍●❍ DoReMiFaSoLaTiDo

f. When the desired alarm tone has been reached, release all buttons.

Press/release RESET once to silence and lock the tone.

Volume Settings

Since each alarm tone is different, you may wish to change the volume setting whenever the alarm tone selection is changed. You may also choose to set different volumes for DAY and NITE modes. For any selected alarm tone, there are 7 selectable volumes each for DAY and NITE modes. (You may wish to have a quieter or louder volume at night than during the day.)

1. First select DAY mode (blue light off) or NITE mode (blue light on)

by pressing the DAY/NITE button on the left.

2. To hear the current volume in that mode,

a. Press and hold RESET.

b. Press and release DAY/NITE VOLUME.

c. Release RESET. You will hear the current volume and tone setting. Silence by pressing RESET.

3. To change the volume setting,

a. Press and hold RESET.

b. Press and hold DAY/NITE VOLUME.

c. Release RESET.

d. Continue holding DAY/NITE VOLUME and press/release RESET

until desired volume is reached. Each press/release of the RESET advances volume one step. If it is at max (7), the sequence will start over at 1.

e. For a visual indication of what setting you’re on, observe the 3 red

LEDs.

Setting

❍ = of

● = on

Sound Level (approx)

1 ❍❍● 67db

❍●❍ 73db

❍●● 77db

●❍❍ 80db

●❍● 81db

●●❍ 83db

●●● 85db

f. When desired volume is reached, release all buttons. Press/release

RESET once more to silence and lock in the volume. The Classic-Check

Unit’s settings will remain unchanged during power interruptions. If you wish to change the volume setting in the other mode (Day or Nite), go back to step 1, change the mode, and repeat the process.

Troubleshooting

Problem: No alarm - Patient out of bed

Check:

1. Are you using the Bed-Check®Sensormat®or another manufacturer’s mat? Adefective mat or a mat provided by a different manufacturer will generally cause the Control Unit to alarm when it is plugged into the unit and power is on.

2. Did the patient get up during the preset HOLD period?

3. Is the Sensormat

bent through misplacement or handling? Is it

functional? Try another Sensormat®.

4. Is there an object putting pressure on the Sensormat

simulating the

patient’s weight?

5. Is there power to the unit? (Note that if it is connected to the nurse call system and power to the unit is interrupted, the unit will alarm the nurse call system.)

Problem: Control Unit alarms during set up

Check:

1. Is the connector between the Sensormat®and Control Unit snapped in properly?

2. Has the cord been pulled from the Sensormat

or its connector?

3. Is the mat a Bed-Check®Sensormat®?

Problem: Alarm triggered - Patient in bed

Check:

1. Did the patient get up and return to the bed upon hearing the alarm?

2. Is the mat a Bed-Check

Sensormat®?

3. Is the Sensormat®placed beneath the patient’s buttocks, or if used behind the back, is the patient of sufficient weight and the bed properly adjusted?

4. Has the Sensormat

slipped toward the end of the bed because the rubber bands and clips were not used to secure the Sensormat®into position beneath the patient’s buttocks?

5. Is the connector between the Sensormat

and Control Unit snapped in

properly?

6. Is the time delay set too low for the patient’s level of activity?

7. If the patient weighs less than 100 pounds, has the system been tested with that patient?

8. Has the Sensormat

cord been pulled out or damaged (check moving bed

parts)?

Test the system’s operations daily. Failure to do so could result in injury or death.

WARNING

Problem: Room alarm triggered - No call at nursing station

-orNurse call will not turn off after an alarm

Check:

1. Is the nurse call plug firmly connected to the patient station or adapter?

2. Is the call cord or pillow speaker firmly connected to the patient station or adapter?

3. Is the adapter firmly connected to the patient station?

4. Was the Control Unit reset after an alarm before the nurse call system alarm was canceled?

5. Has the nurse call adapter been tested for proper functioning?

6. Is the mat a Bed-Check

Sensormat®?

7. If the control unit is not set to the proper nurse call system configuration (N.O. or N.C.), the unit will alarm the nurse call system as soon as power is applied to the unit.

Care and Maintenance

If maintenance or opening of the Control Unit is required, it should be performed in a static-controlled (free) environment by qualified personnel.

The Control Unit and the Sensormat

may be cleaned with a damp cloth or sponge using mild disinfectants. Never use alcohol, acidic or harsh petroleum based cleaners. If absolutely essential, the unit may be gas sterilized up to 120

Danger of electrical shock. Unplug before servicing. Never immerse the power supply or Control Unit in any liquid.

WARNING

The Bed-Check®Control Unit may not be effective with another manufacturer’s sensing device, the use of which may cause intermittent and unreliable operation resulting in injury or death. It may also damage the Bed-Check

Control

Unit and will void the Bed-Check

warranty.

CAUTION

LIMITED WARRANTY: BED-CHECK®CONTROL UNITS

1. WARRANTOR:

This Limited Warranty is given by Stanley Security Solutions, Inc., doing business at Lincoln, NE 68503.

2. DURATION:

This Limited Warranty begins on the date the product is delivered to the purchaser and continues for a period of two years (new units) or one year (refurbished units).

3. TO WHOM THIS LIMITED WARRANTY IS GIVEN:

This Limited Warranty is given to the original purchaser of Bed-Check's® products only.

4. PRODUCTS COVERED:

This Limited Warranty covers all Bed-Check® Control Units. (i.e. Model Vr, Classic-Check, Chair-Check II, and Basic-Check)

5. WHAT IS COVERED UNDER THIS LIMITED WARRANTY:

Defects in material and workmanship which occur within the defined duration of this limited warranty. Warrantor makes no other warranties expressed or implied, including without limitation, warrantor makes no warranty as to merchantability or fitness for a particular purpose.

6. WHAT IS NOT COVERED UNDER THIS LIMITED WARRANTY:

a) ANY INCIDENTAL, INDIRECT, OR CONSEQUENTIAL LOSS, DAMAGE, OR EXPENSE THAT MAY RESULT FROM ANY DEFECT, FAILURE, OR MALFUNCTION OF THE CONTROL UNITS. b) ANY INCIDENTAL, INDIRECT, OR CONSEQUENTIAL LOSS, DAMAGE, OR EXPENSE THAT MAY RESULT FROM USE OF THE CONTROL UNITS WITH ANOTHER MANUFACTURER'S PRESSURE SENSITIVE MAT, SENSING DEVICE, OR OTHER FALLPREVENTION PRODUCT.

NOTE: SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OFINCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATIONS OR EXCLUSIONS MAY NOT APPL YTO YOU.

c) Any defects or damage to the Control Units that may result from use of the Control Units with another manufacturer's parts, pressure sensitive mat, sensing device, or other fall prevention product. d) Any failure that results from an accident, purchaser's abuse, neglect or failure to operate the Control Units in accordance with the instructions provided in the owner's manual(s) supplied with the Control Units. e) Any Control Units which have the serial numbers altered, defaced or removed. f) Any Control Units which have been altered or modified in any way without the express written consent of Bed-Check®. g) Any Control Units which have been repaired other than by Bed-Check®.

7. RESPONSIBILITIES OF WARRANTOR UNDER THIS LIMITED WARRANTY:

a) In the event of a defect, malfunction, or other failure of the product not caused by any misuse or damage to the product while in the possession of purchaser, the warrantor will remedy the failure or defect without charge to the purchaser within a reasonable time. The remedy will consist of repair or replacement of the product, or refund of the purchase price, at the warrantor's option. If the product is no longer available, warrantor will supply purchaser with a comparable product or refund the purchase price at warrantor's option. However, the warrantor will not elect refund unless it is unable to provide replacement, and repair is not commercially practicable and cannot be made within a reasonable time, or unless the purchaser is willing to accept such refund. b) If this product or one of its component parts contains a defect or malfunction, after a reasonable number of attempts by the warrantor to remedy the defects or malfunctions, the purchaser will be entitled to either a refund or replacement of the product or its component part or parts. Replacement of a component part includes its free installation.

8. RESPONSIBILITIES OF THE PURCHASER UNDER THIS LIMITED WARRANTY:

a) Disinfect the Control Unit, if necessary, so that it is reasonably free from infectious matter. b) Package the Control Unit with a minimum of two inches of shock absorbent packaging material. Deliver or ship the Control Unit to Stanley Security Solutions, Lincoln, NE 68503. Freight costs, if any, must be borne by the purchaser. c) Use the Control Unit with reasonable care and in accordance with the supplied owner's manual.

THIS LIMITED WARRANTY GIVES YOU SPECIFIC LEGALRIGHTS AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE.

LIMITED WARRANTY BED-CHECK®SENSORMATS

1. WARRANTOR:

This Limited Warranty is given by Stanley Security Solutions, Inc., Lincoln, NE 68503.

2. DURATION:

This Limited Warranty begins on the date the product is delivered to the purchaser and continues for a period of one year or for the duration of the warranty stated on the Sensormat® label from the date first installed, whichever comes first.

3. TO WHOM THIS LIMITED WARRANTY IS GIVEN:

This Limited Warranty is given to the original purchaser of Bed-Check's® products only.

4. PRODUCTS COVERED:

This Limited Warranty covers all Bed-Check® Sensormats®.

5. WHAT IS COVERED UNDER THIS LIMITED WARRANTY:

Defects in material and workmanship which occur within the period described in paragraph 2. Warrantor makes no other warranties expressed or implied, including without limitation, warrantor makes no warranty as to merchantability or fitness for a particular purpose.

6. WHAT IS NOT COVERED UNDER THIS LIMITED WARRANTY:

a) ANY INCIDENTAL, INDIRECT, OR CONSEQUENTIAL LOSS, DAMAGE, OR EXPENSE THAT MAY RESULT FROM ANY DEFECT, FAILURE, OR MALFUNCTION OF THE SENSORMAT® ANY INCIDENTAL, INDIRECT, OR CONSEQUENTIAL LOSS, DAMAGE, OR EXPENSE THAT MAY RESULTFROM USE OF THE SENSORMAT® WITH ANOTHER MANUFACTURER'S CONTROLUNIT OR OTHER FALL PREVENTION PRODUCT.

NOTE: SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTALOR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATIONS OR EXCLUSIONS MAY NOT APPL YTO YOU.

b) Any defects or damage to the Sensormat® that may result from use of the Sensormat® with another manufacturer's parts, control unit, or other fall prevention product. c) Any failure that results from an accident, purchaser's abuse, neglect or failure to operate the Sensormat® in accordance with the instructions provided on the Sensormat® label. d) Any Sensormat® which has the serial numbers altered, defaced or removed. e) Any Sensormat® which has been altered or modified in any way without the express written consent of BedCheck®. f) Any Sensormat® which has been repaired other than by Bed-Check®.

7. RESPONSIBILITIES OF WARRANTOR UNDER THIS LIMITED WARRANTY:

8. RESPONSIBILITIES OF THE PURCHASER UNDER THIS LIMITED WARRANTY:

a) Disinfect the Sensormat®, if necessary, so that it is reasonably free from infectious matter. b) Package the Sensormat® unfolded and in a flat position. Deliver or ship the Sensormat® to Stanley Security Solutions, Inc. Lincoln, NE 68503. Freight costs, if any, must be borne by the purchaser. c) Use the Sensormat® with reasonable care and in accordance with the supplied owner's manual.

THIS LIMITED WARRANTY GIVES YOU SPECIFIC LEGALRIGHTS AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE.

Bed-Check, Classic-Check, and Sensormat

are registered trademarks of

Stanley Black & Decker or its affiliates.

Stanley Healthcare Bed-Check Classic-Check Fall Risk Monitoring System User Guide User Guide

Specifications and Main Features

Frequently Asked Questions

User Manual