Thank you for purchasing this car audio product.
Please read this manual carefully before operating this car audio product.
Please keep this manual for future use. It will be helpful to you if you are encounter any
operational problem.
Selecting fine audio equipment is only the start of your musical enjoyment.
Now it is time to consider how to maximize the enjoyment you will get from
knowing how to work your new car stereo receiver.
We hope you enjoy using this product and encourage you to always listen at
a moderate, safe sound level to avoid any possible hearing damage or loss.
If you listen to excessively loud sound over time, your hearing can adapt to
higher volumes and what sounds "normal" to you may be quite harmful and
can cause you to have permanent hearing loss. So please practice "safe sound"
and always listen at moderate sound levels only.
Start with your volume control at the lowest setting, and slowly increase the level
until you can hear it comfortably and clearly, free from distortion.
Once you have established this comfortable sound level, leave it there.
WARNING!
To prevent direct exposure to laser beam, do not try to open the enclosure.
Visible and invisible laser radiation will damage your eyes.
To protect our environment, do not dispose of electrical equipment in the domestic waste.
Please return any electrical equipment that you will no longer use to the collection points
provided for their disposal.
This helps avoid the potential effects of incorrect disposal on the environment and human
health. This will contribute to the recycling and other forms of reutilization of electrical and
electronic equipment. Information concerning where the equipment can be disposed of can
be obtained from your local authority.
Preface
Page 1 Page 8
Page 7 Page 2
VOL DEFA: After pressing SEL button, VOL will be displayed. Then you can
pre-select a constant switch-on volume by using the VOL knob.
CLK ON/OFF
CLK ON: Clock will always show on the display when power is off.
CLK OFF: Clock will not show on the display when power is off.
4. POWER ON/OFF & MUTE
When the unit is power off, the unit will turn on by pressing any button except
the EJECT and the RELEASE button.
When the unit is power on, press and hold the power button for more than 0.5
seconds, turns the unit off.
When the unit is power on, pressing the power briefly will turn the MUTE on/off.
5. LCD Display
6. CD SLOT
7&8. TUNE, SEEK, TRACK, SKIP UP / DOWN BUTTONS
a) During RADIO mode:
Press the >>| or |<< button briefly to manually tune up/down to the desired
radio station frequency step by step.
Press and hold the >>| or |<< button for longer than 0.5 seconds, to automatically
tune up/down to the radio station frequency of strong signal.
b) During disc, MMC/SD, USB playback mode:
Press the >>| button briefly to play next track.
Press the |<< button briefly to play the current track from the beginning of it
if the playing time is more than 2 seconds.
Press the |<< button briefly to play the previous track if the playing time is
less than 2 seconds.
Press the >>| or |<< button and hold to skip forwards or backwards, release
to resume normal playback.
9-14. PRESET STATION MEMORIES 1-6(||, INT, RPT, RDM) BUTTONS
a) During radio mode:
When pressed briefly, these buttons select a preset pre programed stations. If
any of the six buttons are pressed for more than 2 seconds, the station currently
being listened to is memorized into the selected preset button.
b) During disc, MMC/SD or USB mode:
1) Press the TOP/ >|| button briefly to pause the playback of the disc, MMC/SD
or USB. Press again to resume normal playback of the disc, MMC/SD or USB.
Press the TOP/>|| button and hold for approximately 0.5 seconds to play the
first track of the disc, MMC/SD or USB.
2) Press the INT button to sample the first 10 seconds part of each track, and the
INT ON will be visible on the LCD display.
In the process of INT, pressINT button again to stop sampling and to continue
playing the current track, and the LCD will display INT OFF.
3) Press the RPT button once to play the current track repeatedly, and the RPT
ONE will be visible on the LCD display.
During MP3/WMA disc, MMC/SD or USB mode, press the RPT button twice
continuously to play the current folder repeatedly, and the RPT ABM will be
visible on the LCD display.
In the process of RPT, press RPT button again to stop playing repeatedly
mode and the LCD will display RPT OFF.
TROUBLE SHOOTING
Before using the check list please make all the connections first.
If you still have questions after going through the checklist, please consult
your local customer service representative.
Common Symptoms
There is no power.
The CDs cannot
be loaded.
Cause
The fuse has blown.
Presence of CD disc inside the player
Inserted disc is upside down
The surface of CD is extremely dirty
or it is damaged.
Temperature inside the car is too
high.
The volume control is set too low.
There is no sound.
The operation keys
do not work
The sound of the
CD player skips
The antenna cable is not connected. Insert the antenna cable firmly into the
antenna socket of the device.
No radio reception.
1.The built-in microcomputer is not
operating properly
2.Front panel is not properly fix into
its place
1. Switch the device off and on again. Or press
the RESET button.
2. Reinstall the front panel
The device has not been wired
correctly.
The installation angle is more than
30 degrees
Wait until the road becomes smoother before
playing the CD.
Adjust the installation angle to less than 30
degrees
Turn up the volume properly.
Check the connections according to the
wiring diagram.
Cool off until the ambient temperature returns
to normal
Clean the CD or try another CD, if this works
correctly, the first CD is properly damaged.
Insert the compact disc with the label facing
upward
Remove the disc from the player
Replace another fuse with the same
amperage rating.
The car ignition is switched off.
If the power supply is properly connected to
the car accessory, switch the ignition key to
ON or " ACC " " " .
Solution
The device does
not work correctly
(EJECT, LOAD,
PLAY)
In automatic search
mode the radio does
not stop at a transmitting station.
Tune in to a radio station manually.The transmission signals are too
weak.
The CDs are loading
only halfway into
the CD tray.
The transport screws have not been
removed.
Remove the transport screws before using.
The surface of the road is uneven.
The surface of CD is extremely dirty
or it is damaged.
Clean the CD or try another CD, if this works
correctly, the first CD is properly damaged.
Page 6 Page 3
4) Press the RDM button to play all tracks on disc in random order, and the RDM
ON will be visible on the LCD display.
In the process of RDM, press RDM button again to stop playing in random
order and the LCD will display RDM OFF.
5) Press the -10 and +10button to move up and down10 tracks at a time.
15. BAND BUTTON
During radio mode:
Press the BND button briefly to select the radio broadcasting band you would
like to hear. The AM/FM band is toggled cyclically through the tuning bands:
->FM 1-> FM 2 -> FM 3 -> AM 1->AM 2 ->.
Press and hold the BND button to select LOCAL/DX mode.
Note: This button is only active for FM reception.
In MMC/SD, USB mode, the file name, folder name, song’s title, artist and album
information will be scrolling on the LCD display.
As long as the current playing MP3/WMA music contains relevant ID3 tag information
in version 1.0/2.0 format, the 3 items underlined above will be scrolling on the LCD
display; otherwise, they will not.
16. MODE BUTTON
Press the MODE button to change among tuner (radio), disc (when a disc is loaded),
MMC/SD card (when an MMC/SD card is inserted) , USB (when anUSB stick is
inserted) and AUX mode.
17. EJECT BUTTON
When the power is on, the loaded disc can be ejected by pressing the EJ button.
18. LOUDNESS BUTTON
When press briefly, the LOUD mode is turned on, its to enhance the bass sound
effect when the volume level is low. Press again to cancel the loudness effect.
19. AS/PS BUTTON (Auto-storage /Preset scan)
During radio mode:
1) When press and hold for more than 1 second, the radio searches from the
current frequency and checks the signal strength level until 6 station are found.
And then the 6 stations frequency are preset to the corresponding preset memory
numbered bank.
2) When press briefly, the radio searches for each preset station in the current band
and plays that preset station for 5 seconds, and then searches again.
During MP3/WMA file in disc, MMC/SD or USB mode:
In track search mode, the LCD will display TRK T000 and flash the highest digit 0
which the SD/MMC card or USB stick contain.
Press the VOL+ or VOL- buttons to select the number of the flashing digit from
0 to 9, and then press the BAND button to confirm the number and flash the next
lower digit 0. Following the same steps as above, choose and confirm the digits
until the desires track number has been selected and press the BAND button to
start playing the track.
FIRST CHARACTER SEARCH mode:
In first character search mode, the display will show the files in alphabetical order
from A to Z. and 0 to 9. If the files are not saved by character names the unit will
display "NONE" on the screen. Use the VOL+ and VOL- buttons to search through
the files and press the SEL button to play the desired file.
ÒÉÄѽâ³ý
CARE FOR USING CD'S:
1. To keep the disc clean:
Do not attach any sticker or adhesive tape on the disc.
Handle the disc by its edge to keep the disc clean and do not touch the surface.
Before playing a disc, wipe it off with a clean, dust-free cleaning cloth.
Wipe the disc outwards from the disc center.
2. When one disc has already been inserted. Inserting another disc will damage the
unit. Insert a disc with labeled surface up, or it will damage the unit.
3. Do not expose the disc to direct sunlight or nearby heat sources such as heating
vents, which can cause the disc to warp.
Do not leave disc in a car if it is parked in direct sunlight as that will lead to a
considerable rise in the temperature inside the car.
4. Always store the disc in its case for protection. Scratched up discs will produce poor
sound performance and cause CD player to skip.
5. In raining day or wet area, the moisture may form on the disc or the optical parts,
the playback may not be possible. If moisture forms on the disc, wipe it off with a
soft cloth.
6. Do not use solvents such as benzine or thinners. Commercially available cleaners
or anti-static spray will damage the unit.
About :
In addition to commercially-recorded audio CD's, this unit can play MP3,CD-R
and CD-R/W discs. In some cases, particularly when recorded on older CD
burners, some MP3,CD-R and CD-R/W discs may not play. Also, whenever you
are recording a CD for playback in this receiver, it is recommended that you
record at 24x or slower speed for CD-R and 4x or slower for CD-R/W to achieve
higher signal quality and better playback performance.
MP3/CD-R/CD-R/W discs
Page 4 Page 5
DIRECTORY SEARCH MODE
In directory search mode the unit will display the root folder. If there is root folder,
the unit will find root folder named “ROOT”.
In this mode, you can use the VOL+ or VOL- buttons to select the desired folder
then press >> | or |<< button to select the desired track in the folder.
Once the desired folder is selected, you can press the SEL button to start playing
the desired track.
20. ST/MO BUTTON
In FM mode, press the ST briefly to select stereo or mono sound mode.
21.CLK BUTTON
Press the CLK button briefly to show the time on the display. After 5 seconds,
it will return to the previous display.
Press the CLK button and hold for more than 1 second until the real time
flashes on the display. Then you can adjust HOUR or MINUTE by press the
VOL+ or VOL- button.
22.AUX INPUT JACK
Press the mode button to select auxiliary input playing mode. You can connect
external audio device to the front auxiliary input jack.
23.MMC/SD CARD SLOT
In order to play the files in the MMC/SD card, insert the MMC/SD card into
the MMC/SD card slot. The system will change into the MMC/SD mode
automatically, and then play the first file in the MMC/SD.
Note:
When MMC/SD card and USB stick are both inserted into their slot or socket,
the system will change into the playback mode of the last one.
24.USB SOCKET
In order to play the files in the USB stick, turn over the plastic cover cap then
insert the USB stick into the USB socket. The system will change into the
USB mode automatically, and play the first file from the USB.
When the USB socket is not used,cover the socket with the plastic cap.
25. FLASHING LED
When the front control panel is removed this indicator flashes.
26. RESET BUTTON
Before operating the unit for the first time, or after replacing the car battery or
changing the connections. You must reset the unit.
Press this button with a pointed object. This operation will erase the clock
setting and stored contents.
27. RELEASE BUTTON
Press the REL button to release the front control panel from the unit chassis,
then pull it out to remove it from the chassis.
When the front control panel is removed the LED indicator flashes.
INSTALLATION METHOD
This is an anti-theft installation method.
The main unit wears a METAL MOUNTING SLEEVE.
Please connect the wiring, eg, the Power supply, the Speakers and the Antenna
according to the requirements of this Instruction Manual, then install the metal
mounting sleeve into the car as per the diagram illustrated below.
Ö÷™CÖ÷™C
METAL
SUPPORT STRAP
Securely affix the metal support
strap into the metal joint that
connects to the vehicle chassis.
To properly fix the metal mounting
sleeve, bend the tabs of the sleeve
against the DASH BOARD with a
screwdriver.
UNIT CHASSIS
PLASTIC TRIM RING
FRONT PANEL
DASHBOARD
METAL MOUNTING SLEEVE
To remove the CD player out of the mounting sleeve,
insert the two supplied keys into the left and right side
slots of the chassis at the same time.
NOTE
Before installing and operating
the CD player, remove the metal
mounting sleeve illustrated by
the arrows.
Remove the two screws that protect
the CD mechanism during transportation
before operating the player.
To attach the removable faceplate, insert the
right side of the faceplate into the right of the
CD player chassis first. Then push the left side
of the faceplate into the chassis until you hear
it “click”.
Loading...