HP LaserJet 1010, 1012, 1015 and 1020
Service Manual
HP LaserJet 1010 series printers and HP LaserJet 1020 printer
Service Manual
Copyright Information
© 2005 Copyright Hewlett-Packard
Development Company, L.P.
Reproduction, adaptation or translation without prior written permission is prohibited except as allowed under the copyright laws.
The information contained in this document is subject to change without notice.
The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and services. Nothing herein should be construed as constituting an additional warranty. HP shall not be liable for technical or editorial errors or omissions contained herein.
Part number Q5911-90945
Edition 1, 4/2005
Information regarding FCC Class B, Parts 15 and 68 requirements can be found in the user guide.
NOTICE TO U.S. GOVERNMENT USERS: RESTRICTED RIGHTS COMMERCIAL COMPUTER SOFTWARE: “Use, duplication, or disclosure by the Government is subject to restrictions as set forth in subparagraph (c) (1)(ii) of the Rights in Technical Data Clause at DFARS 52.227-7013.”
Trademark Credits
Microsoft® and Windows® are U.S. registered trademarks of the Microsoft company.
Safety Information
WARNING!
Potential Shock Hazard
Always follow basic safety precautions when using this product to reduce risk of injury from fire or electric shock.
Read and understand all instructions in the user guide.
Observe all warnings and instructions marked on the product.
Use only a grounded electrical outlet when connecting the HP LaserJet 1010 series printer or HP LaserJet 1020 printer to a power source. If you don’t know whether the outlet is grounded, check with a qualified electrician.
Do not touch the contacts on the end of any of the sockets on the
HP LaserJet 1010 series printer or HP LaserJet 1020 printer. Replace damaged cords immediately.
Unplug this product from wall outlets before cleaning or servicing.
Do not install or use this product near water or when you are wet.
Install the product securely on a stable surface.
Install the product in a protected location where no one can step on or trip over the power cord and the power cord will not be damaged.
If the product does not operate normally, see the online user guide.
Table of contents
1 Product Information |
|
Product configurations............................................................................................................................ |
2 |
HP LaserJet 1010 printer....................................................................................................... |
2 |
HP LaserJet 1012 printer....................................................................................................... |
2 |
HP LaserJet 1015 printer....................................................................................................... |
2 |
HP LaserJet 1020 printer....................................................................................................... |
3 |
Overview of product............................................................................................................................... |
4 |
HP LaserJet 1010 series printers.......................................................................................... |
4 |
HP LaserJet 1020 printer....................................................................................................... |
6 |
Model and serial numbers..................................................................................................... |
7 |
Hardware description............................................................................................................. |
7 |
Firmware description ............................................................................................................ |
8 |
Product specifications............................................................................................................................ |
9 |
Physical specifications........................................................................................................... |
9 |
Printer performance............................................................................................................... |
9 |
Environmental specifications................................................................................................. |
9 |
Electrical specifications........................................................................................................ |
10 |
Acoustic emissions.............................................................................................................. |
11 |
Extended warranty............................................................................................................................... |
12 |
Print-cartridge information ................................................................................................................... |
13 |
Refilled print cartridges ...................................................................................................... |
13 |
Recycling print cartridges ................................................................................................... |
13 |
Regulatory information......................................................................................................................... |
14 |
FCC compliance.................................................................................................................. |
14 |
Canadian DOC regulations.................................................................................................. |
14 |
Korean EMI statement......................................................................................................... |
14 |
Laser statement for Finland................................................................................................. |
15 |
............................................................................................................................ |
15 |
2 Installation and operation |
|
Operating environment ........................................................................................................................ |
18 |
Identifying the control-panel components............................................................................................. |
19 |
Media specifications............................................................................................................................. |
21 |
Supported media sizes........................................................................................................ |
21 |
Guidelines for using media................................................................................................................... |
22 |
Paper and transparencies ................................................................................................... |
22 |
Common media problems table .......................................................................................... |
22 |
Labels.................................................................................................................................. |
23 |
Envelopes ........................................................................................................................... |
23 |
ENWW |
iii |
Envelopes with double-side seams..................................................................... |
23 |
Envelopes with adhesive strips or flaps.............................................................. |
24 |
Card stock and heavy media .............................................................................................. |
24 |
Card-stock construction...................................................................................... |
24 |
Card-stock guidelines.......................................................................................... |
24 |
Loading media...................................................................................................................................... |
25 |
Main input tray..................................................................................................................... |
25 |
Priority feed slot................................................................................................................... |
25 |
Specific types of media ....................................................................................................... |
25 |
Setting media types.............................................................................................................................. |
26 |
Set the media type............................................................................................................... |
26 |
3 Maintenance |
|
Life expectancies of parts that wear .................................................................................................... |
28 |
Cleaning the product............................................................................................................................ |
30 |
Cleaning the print path......................................................................................................... |
31 |
Cleaning the print-cartridge area......................................................................................... |
32 |
Cleaning the pickup roller.................................................................................................... |
34 |
User-replaceable parts ........................................................................................................................ |
35 |
Replacing the pickup roller.................................................................................................. |
35 |
Replacing the separation pad.............................................................................................. |
38 |
Replacing the main input tray (paper-pickup tray assembly)............................................... |
40 |
Replacing the output-bin extension (delivery-tray assembly).............................................. |
41 |
Jams..................................................................................................................................................... |
42 |
Clearing jams....................................................................................................................... |
42 |
Typical media jam locations................................................................................ |
42 |
Removing a jammed page.................................................................................. |
43 |
4 Operational overview |
|
Basic functions..................................................................................................................................... |
46 |
Formatter system................................................................................................................................. |
47 |
Central processing unit ....................................................................................................... |
47 |
RAM..................................................................................................................................... |
47 |
USB interface....................................................................................................................... |
47 |
Parallel interface (HP LaserJet 1015 printer only)............................................................... |
47 |
Control panel....................................................................................................................... |
47 |
Draft mode (EconoMode).................................................................................................... |
48 |
HP Memory Enhancement technology (MEt)...................................................................... |
48 |
Enhanced I/O ...................................................................................................................... |
48 |
PJL overview ...................................................................................................................... |
49 |
Printer functions................................................................................................................................... |
50 |
Engine control system (engine control unit and power assembly)....................................... |
50 |
Printer-engine-control system............................................................................. |
51 |
Printer laser/scanner unit ................................................................................... |
52 |
Power system on the engine power assembly.................................................... |
53 |
Image-formation system...................................................................................................... |
54 |
The seven image-formation processes .............................................................. |
55 |
Print cartridge...................................................................................................................... |
56 |
Printer paper-feed system................................................................................................... |
56 |
Jam detection ..................................................................................................................... |
58 |
iv |
ENWW |
Conditions of jam detection................................................................................. |
58 |
Solenoid, sensors, switches, and motor.............................................................................. |
58 |
Basic sequence of operation (formatter-to-printer).............................................................. |
60 |
5 Removal and replacement |
|
Removal and replacement strategy...................................................................................................... |
64 |
Required tools ..................................................................................................................... |
64 |
Before performing service.................................................................................................... |
64 |
Print cartridge ..................................................................................................................... |
65 |
Differences between the HP LJ 1010 series printer models................................................ |
66 |
Parts removal order ............................................................................................................ |
67 |
User-replaceable parts ........................................................................................................................ |
68 |
Replacing the pickup roller ................................................................................................. |
68 |
Replacing the separation pad.............................................................................................. |
71 |
Replacing the main input tray (paper-pickup tray assembly)............................................... |
73 |
Replacing the output-bin extension (delivery-tray assembly).............................................. |
74 |
Covers.................................................................................................................................................. |
75 |
Right-side cover................................................................................................................... |
75 |
Left-side cover..................................................................................................................... |
77 |
Rear panel and top-cover assembly.................................................................................... |
77 |
Front cover........................................................................................................................... |
82 |
Internal assemblies.............................................................................................................................. |
84 |
Transfer-roller assembly...................................................................................................... |
84 |
Engine-power assembly...................................................................................................... |
87 |
Fuser (fixing) assembly........................................................................................................ |
89 |
Paper-pickup assembly....................................................................................................... |
91 |
Engine control unit (ECU) assembly.................................................................................... |
92 |
Laser/scanner assembly...................................................................................................... |
96 |
6 Troubleshooting |
|
Basic troubleshooting........................................................................................................................... |
98 |
Troubleshooting checklist.................................................................................................... |
98 |
Control-panel power-on functions (HP LaserJet 1010 series printers)............................................... |
100 |
Control-panel pages (HP LaserJet 1010 series printers only)............................................................ |
101 |
Control-panel lights (HP LaserJet 1010 series printers)..................................................................... |
102 |
Control-panel light patterns (HP LJ 1010 series printers).................................................. |
102 |
Fatal errors (HP LJ 1010 series printers)........................................................................... |
105 |
Control-panel lights (HP LaserJet 1020 printer)................................................................................. |
106 |
Status-light patterns........................................................................................................... |
106 |
Jams................................................................................................................................................... |
108 |
Clearing jams..................................................................................................................... |
108 |
Typical media jam locations.............................................................................. |
108 |
Removing a jammed page................................................................................ |
108 |
Print-quality troubleshooting............................................................................................................... |
111 |
Print-cartridge problems.................................................................................................... |
111 |
Checking the print cartridge.............................................................................. |
111 |
To redistribute toner in the print cartridge......................................... |
111 |
Solving print-quality problems............................................................................................ |
111 |
Solving paper-feed problems............................................................................................................. |
122 |
Functional checks............................................................................................................................... |
124 |
ENWW |
v |
Half self-test functional check............................................................................................ |
124 |
To perform a half self-test check....................................................................... |
124 |
To perform other checks................................................................................... |
124 |
Drum-rotation functional check ......................................................................................... |
126 |
High-voltage-contacts check.............................................................................................. |
127 |
To check the print-cartridge contacts .............................................................. |
127 |
To check the printer high-voltage contacts ...................................................... |
128 |
Troubleshooting tools......................................................................................................................... |
129 |
Repetitive-image-defect ruler............................................................................................. |
129 |
Circuit diagram .................................................................................................................. |
130 |
Solenoid, sensors, switches, and motor............................................................................................. |
131 |
7 Parts and diagrams |
|
Ordering parts and supplies............................................................................................................... |
134 |
Parts.................................................................................................................................. |
134 |
Related documentation and software................................................................................ |
134 |
Parts that wear .................................................................................................................. |
134 |
Accessories and consumables........................................................................................................... |
135 |
Accessories....................................................................................................................... |
135 |
Common hardware ........................................................................................................... |
137 |
How to use the parts lists and diagrams............................................................................ |
137 |
Printer exchange/parts....................................................................................................................... |
138 |
Major components.............................................................................................................................. |
140 |
Alphabetical parts list......................................................................................................................... |
143 |
Numerical parts list............................................................................................................................. |
146 |
Index................................................................................................................................................................... |
149 |
vi |
ENWW |
List of tables
Table 1-1 |
Physical specifications.................................................................................................................... |
9 |
Table 1-2 |
Performance.................................................................................................................................... |
9 |
Table 1-3 |
Environmental specifications (HP LJ 1010 series printers and HP LJ 1020 printer) ...................... |
9 |
Table 1-4 |
Power requirements...................................................................................................................... |
10 |
Table 1-5 |
Power consumption (average, in watts)........................................................................................ |
10 |
Table 1-6 |
Acoustic emissions........................................................................................................................ |
11 |
Table 2-1 |
Media sizes................................................................................................................................... |
21 |
Table 3-1 |
Life expectancies of parts that wear.............................................................................................. |
28 |
Table 4-1 |
Basic sequence of operation......................................................................................................... |
60 |
Table 6-1 |
Basic troubleshooting .................................................................................................................. |
98 |
Table 6-2 |
Power-on functions: time ranges (HP LJ 1010 series printers only)........................................... |
100 |
Table 6-3 |
Control-panel pages: time ranges (HP LJ 1010 series printers only).......................................... |
101 |
Table 6-4 |
Control-panel light patterns (HP LJ 1010 series printers)........................................................... |
102 |
Table 6-5 |
Control-panel light patterns (HP LJ 1020 printer)........................................................................ |
106 |
Table 6-6 |
Solving print-quality problems..................................................................................................... |
111 |
Table 6-7 |
Solving paper-feed problems...................................................................................................... |
122 |
Table 7-1 |
Technical support websites......................................................................................................... |
134 |
Table 7-2 |
Accessories................................................................................................................................. |
135 |
Table 7-3 |
Printer exchange/parts................................................................................................................ |
139 |
Table 7-4 |
Major components....................................................................................................................... |
141 |
Table 7-5 |
Alphabetical parts list.................................................................................................................. |
143 |
Table 7-6 |
Numerical parts list...................................................................................................................... |
146 |
ENWW |
vii |
viii |
ENWW |
List of figures
Figure 1-1 |
Front and right-side view (HP LJ 1010 series printers)................................................................... |
4 |
Figure 1-2 |
Back and left-side view (HP LJ 1010 series printers)...................................................................... |
5 |
Figure 1-3 |
Front and right-side view (HP LJ 1020 printer)............................................................................... |
6 |
Figure 1-4 |
Back and left-side view (HP LJ 1020 printer).................................................................................. |
6 |
Figure 1-5 |
Modeland serial-number label (HP LJ 1010 printer is shown)...................................................... |
7 |
Figure 2-1 |
HP LaserJet 1010 series printer dimensions................................................................................ |
18 |
Figure 2-2 |
HP LaserJet 1020 printer dimensions........................................................................................... |
18 |
Figure 2-3 |
Control-panel lights and buttons (HP LJ 1010 series printers)...................................................... |
19 |
Figure 2-4 |
Control-panel lights (HP LJ 1020 printer)...................................................................................... |
20 |
Figure 3-1 |
Main input tray (HP LaserJet 1020 printer shown)........................................................................ |
40 |
Figure 3-2 |
Output-bin extension .................................................................................................................... |
41 |
Figure 4-1 |
Basic configuration........................................................................................................................ |
46 |
Figure 4-2 |
Printer functional-block diagram.................................................................................................... |
50 |
Figure 4-3 |
Laser/scanner operation............................................................................................................... |
52 |
Figure 4-4 |
High-voltage power supply circuit................................................................................................. |
54 |
Figure 4-5 |
Image formation-block diagram..................................................................................................... |
55 |
Figure 4-6 |
Printer paper path ........................................................................................................................ |
57 |
Figure 4-7 |
Solenoid, sensors, switches, and motor........................................................................................ |
59 |
Figure 4-8 |
Printer timing diagram................................................................................................................... |
61 |
Figure 5-1 |
Removing the print cartridge......................................................................................................... |
65 |
Figure 5-2 |
HP LaserJet 1015 parallel port...................................................................................................... |
66 |
Figure 5-3 |
Parts-removal block diagram........................................................................................................ |
67 |
Figure 5-4 |
Main input tray (HP LaserJet 1020 printer shown)........................................................................ |
73 |
Figure 5-5 |
Output-bin extension .................................................................................................................... |
74 |
Figure 5-6 |
Remove the right-side cover (1 of 4; HP LJ 1020 printer shown)................................................. |
75 |
Figure 5-7 |
Remove the right-side cover (2 of 4; HP LJ 1020 printer shown)................................................. |
75 |
Figure 5-8 |
Remove the right-side cover (3 of 4; HP LJ 1020 printer shown)................................................. |
76 |
Figure 5-9 |
Remove the right-side cover (4 of 4; HP LJ 1020 printer shown)................................................. |
76 |
Figure 5-10 |
Remove the rear panel and top-cover assembly (1 of 6).............................................................. |
77 |
Figure 5-11 |
Remove the rear panel and top-cover assembly (2 of 6).............................................................. |
78 |
Figure 5-12 |
Remove the rear panel and top-cover assembly (3 of 6).............................................................. |
78 |
Figure 5-13 |
Remove the rear panel and top-cover assembly (4 of 6; HP LJ 1020 printer shown)................... |
79 |
Figure 5-14 |
Remove the rear panel and top-cover assembly (5 of 6).............................................................. |
79 |
Figure 5-15 |
Remove the rear panel and top-cover assembly (6 of 6).............................................................. |
80 |
Figure 5-16 Reinstall the top-cover assembly (1 of 2)...................................................................................... |
80 |
|
Figure 5-17 Reinstall the top-cover assembly (2 of 2)...................................................................................... |
81 |
|
Figure 5-18 |
Remove the front cover (1 of 3).................................................................................................... |
82 |
Figure 5-19 |
Remove the front cover (2 of 3).................................................................................................... |
83 |
Figure 5-20 |
Remove the front cover (3 of 3).................................................................................................... |
83 |
Figure 5-21 |
Remove the transfer roller (1 of 3)................................................................................................ |
84 |
ENWW |
ix |
Figure 5-22 |
Remove the transfer roller (2 of 3)................................................................................................ |
85 |
Figure 5-23 |
Remove the transfer roller (3 of 3)................................................................................................ |
85 |
Figure 5-24 |
Remove the engine-power assembly (1 of 2; HP LJ 1020 printer shown).................................... |
87 |
Figure 5-25 |
Remove the engine power assembly (2 of 2)................................................................................ |
88 |
Figure 5-26 |
Remove the fuser (fixing) assembly (1 of 2)................................................................................. |
89 |
Figure 5-27 |
Remove the fuser (fixing) assembly (2 of 2)................................................................................. |
90 |
Figure 5-28 |
Remove the paper-pickup assembly............................................................................................. |
91 |
Figure 5-29 |
Remove the ECU assembly (1 of 6).............................................................................................. |
92 |
Figure 5-30 |
Remove the ECU assembly (2 of 6).............................................................................................. |
93 |
Figure 5-31 |
Remove the ECU assembly (3 of 6).............................................................................................. |
93 |
Figure 5-32 |
Remove the ECU assembly (4 of 6).............................................................................................. |
94 |
Figure 5-33 |
Remove the ECU assembly (5 of 6).............................................................................................. |
94 |
Figure 5-34 |
Remove the ECU assembly (6 of 6).............................................................................................. |
95 |
Figure 5-35 |
Remove the laser/scanner assembly............................................................................................ |
96 |
Figure 6-1 |
Control-panel-lights legend......................................................................................................... |
102 |
Figure 6-2 |
Control-panel lights (HP LJ 1020 printer).................................................................................... |
106 |
Figure 6-3 |
Control-panel-light legend (HP LJ 1020 printer).......................................................................... |
106 |
Figure 6-4 |
Check the fuser connections (HP LaserJet 1010 series shown)................................................. |
125 |
Figure 6-5 |
Print-cartridge high-voltage contacts........................................................................................... |
127 |
Figure 6-6 |
Printer high-voltage contacts....................................................................................................... |
128 |
Figure 6-7 |
Repetitive-image-defect ruler...................................................................................................... |
129 |
Figure 6-8 |
Circuit diagram............................................................................................................................ |
130 |
Figure 6-9 |
Solenoid, sensors, switches, and motor...................................................................................... |
131 |
Figure 7-1 |
HP LJ 1010 series and HP LJ 1020 product............................................................................... |
138 |
Figure 7-2 |
Major components (HP LJ 1010 series shown).......................................................................... |
140 |
x |
ENWW |
This chapter provides general product information for HP LaserJet 1010 series printer and the HP LaserJet 1020 printer.
●Product configurations
●Overview of product
●Product specifications
●Extended warranty
●Print-cartridge information
●Regulatory information
ENWW |
1 |
The HP LaserJet 1010 series printers and the HP LaserJet 1020 printer are designed to print documents easily and with the laser quality that customers have come to expect from an HP LaserJet product. The following sections describe the configurations of the HP LaserJet 1010 series printers and the
HP LaserJet 1020 printer.
The HP LaserJet 1010 printer (HP LJ 1010) is the base model in the HP LaserJet 1010 series printers. It offers the following features:
■Prints up to 12 pages per minute (ppm)
■10 seconds or less to first page out
■600 x 600 dpi
■150-sheet input capacity (75-g/m2 [20-lb] media)
■125-sheet output bin capacity
■A priority feed slot
■A horizontal paper-feed path
■8 MB of RAM (not expandable)
■A host-based driver
■A USB port
The HP LaserJet 1012 printer (HP LJ 1012) is the mid-range model in the series. It offers all of the features of the HP LaserJet 1010 printer, plus the following features:
■Prints up to 14 ppm on A4-size media and 15 ppm on letter-size media
■FastRes 1200: 1200 dpi effective output quality (600 x 600 x 2 dpi with HP Resolution Enhancement technology [REt])
■Networking support through HP Jetdirect devices
The HP LaserJet 1015 printer (HP LJ 1015) is the top model in the series. It offers all of the features of the HP LaserJet 1012, plus the following features:
■16 MB of RAM (not expandable)
■A host-based driver and HP PCL 5e driver
■A USB port and a parallel port
2 Chapter 1 Product Information |
ENWW |
The HP LaserJet 1020 printer (HP LJ 1020) offers the following features:
■Prints up to 14 ppm for A4-size media and 15 ppm for letter-size media
■10 seconds or less to first page out
■FastRes 1200: 1200 dpi effective output quality (600 x 600 x 2 dpi with HP Resolution Enhancement technology [REt])
■150-sheet input capacity (75-g/m2 [20-lb] media)
■125-sheet output bin capacity
■A priority feed slot
■EconoMode (saves toner)
■Prints watermarks, booklets, and multiple pages per sheet (N-up), and can print the first page on different media from the remainder of the document
■2 MB of RAM
■2,000-page print cartridge
■A USB 2.0 Hi-Speed port
ENWW |
Product configurations 3 |
1
10 |
2 |
|
|
|
3 |
9 |
4 |
|
5 |
||
8 |
||
|
||
7 |
6 |
|
|
Figure 1-1 Front and right-side view (HP LJ 1010 series printers)
1 |
ATTENTION light |
|
|
2 |
READY light |
|
|
3 |
GO light |
|
|
4 |
GO button |
|
|
5 |
CANCEL JOB button |
|
|
6 |
Print-cartridge door |
|
|
7 |
Priority feed slot |
|
|
8 |
Main input tray |
|
|
9 |
Tray cover (only for the HP LaserJet 1012 printer and the HP LaserJet 1015 printer in some countries/regions) |
|
|
10 |
Output bin |
|
|
4 Chapter 1 Product Information |
ENWW |
11
12
13 |
14 |
15 |
Figure 1-2 Back and left-side view (HP LJ 1010 series printers)
11USB port
12Parallel port (HP LaserJet 1015 printer only)
13On/off switch
14Power receptacle
15Separation pad
ENWW |
Overview of product 5 |
Figure 1-3 Front and right-side view (HP LJ 1020 printer)
1ATTENTION light
2READY light
3Print-cartridge door
4Output-media support
5Priority feed slot
6150-sheet main input tray
7Output bin
8
10 |
9 |
|
|
|
11 |
Figure 1-4 Back and left-side view (HP LJ 1020 printer)
8On/off switch
9Power receptacle
10USB port
11Separation pad
6 Chapter 1 Product Information |
ENWW |
The model number and serial number are listed on an identification label located on the back of the product.
The serial number contains information about the country/region of origin, and the revision level, production code, and production number of the product.
The label also contains power-rating and regulatory information.
Figure 1-5 Modeland serial-number label (HP LJ 1010 printer is shown)
The HP LaserJet 1010 printer provides 600 x 600 dpi printing. The HP LaserJet 1012, 1015, and 1020 printers offer HP REt technology for 600 x 600 x 2 dpi printing (effectively 1200 dpi).
The printers print at 12 ppm (HP LaserJet 1010) or 15 ppm for letter-size paper and 14 ppm for A4-size paper (HP LaserJet 1012, 1015, and 1020). With 600 dpi printing for the HP LaserJet 1010 printer and an effective 1200 dpi printing resolution for the other models, the printers have exceptional text and graphics print quality. The simple control panels and improved paper-handling make these printers easy to use.
The main input tray has a 150-sheet (75-g/m2 [20-lb] media) capacity for continuous, multiple-page printing. The priority feed slot is used to manually feed single sheets of most recommended media and holds up to ten sheets of 75-g/m2 (20-lb) media. Both the main input tray and the priority feed slot are center-justified for all supported media sizes. The output bin holds up to 125 sheets of 75-g/m2 (20-lb) media.
These printers have a very fast first-page-out, at less than 10 seconds to first page out. The base memory contains 8 MB of RAM for the HP LaserJet 1010 series printers and 2 MB for the HP LaserJet 1020 printer. These printers use an embedded 133 MHz processor.
The print engine has an average duty cycle of 1,000 pages per month (7,000 peak) or 50,000 total pages printed. The standard print-cartridge life is 2,000 pages, in accordance with ISO/IEC 19752.
NOTE Actual print cartridge life depends on specific usage.
ENWW |
Overview of product 7 |
The firmware in the printers includes these features:
■Host-based printing
■PCL 5e (HP LaserJet 1015 printer only)
■EconoMode functionality
8 Chapter 1 Product Information |
ENWW |
This section details the specifications for the HP LaserJet 1010 series printers and the HP LaserJet 1020 printer.
Table 1-1 Physical specifications
Model |
Height |
Depth |
Width |
Weight |
|
|
|
|
|
HP LaserJet 1010 series printers and the |
209 mm |
242 mm |
370 mm |
5.9 kg (13.0 lb) |
HP LaserJet 1020 printer |
(8.3 inches) |
(9.5 inches) |
(14.6 inches) |
|
|
|
|
|
|
Table 1-2 Performance
Model |
Print resolution (normal) |
Print speed (A4-size media) |
|
|
|
HP LaserJet 1010 printer |
600 x 600 dpi |
12 ppm |
|
|
|
HP LaserJet 1012 printer |
600 x 600 dpi |
14 ppm |
|
|
|
HP LaserJet 1015 printer |
600 x 600 dpi |
14 ppm |
|
|
|
HP LaserJet 1020 printer |
600 x 600 dpi |
14 ppm |
1 1200 dpi effective output quality, 600 x 600 x 2 dpi with HP Resolution Enhancement technology (REt)
Table 1-3 Environmental specifications (HP LJ 1010 series printers and HP LJ 1020 printer)
Category |
Specification |
|
|
Operating environment (unit plugged into an alternatingcurrent [ac] outlet)
■Temperature: 10° to 32.5°C (50° to 90.5°F)
■Humidity: 20 to 80% relative humidity (no condensation)
Storage environment (unit not plugged into an ac outlet)
■Temperature: 0° to 40°C (32° to 104°F)
■Humidity: 10 to 80% relative humidity (no condensation)
ENWW |
Product specifications 9 |
WARNING! Power requirements are based on the country/region where the printer is sold. Do not convert operating voltages. This might damage the printer and void the product warranty.
Table 1-4 Power requirements
Specification |
110-volt models |
220-volt models |
|
|
|
Power requirements |
110–127 V (±10%) |
220–240 V (±10%) |
|
50/60 Hz (±2 Hz) |
50/60 Hz (±2 Hz) |
|
|
|
Rated current |
4.0 amps |
2.3 amps |
|
|
|
WARNING! Power sources are not interchangeable.
Table 1-5 Power consumption (average, in watts)1
Product model |
Printing2 |
Ready2 |
PowerSave |
Off |
HP LaserJet 1010 |
250 W |
2 W |
2 W |
0 W |
printer |
|
|
|
|
|
|
|
|
|
HP LaserJet 1012 |
250 W |
2 W |
2 W |
0 W |
printer |
|
|
|
|
|
|
|
|
|
HP LaserJet 1015 |
250 W |
2 W |
2 W |
0 W |
printer |
|
|
|
|
|
|
|
|
|
HP LaserJet 1020 |
250 W |
4 W |
4 W |
0 W |
printer |
|
|
|
|
1Values are subject to change. See www.hp.com/support/lj1010 or www.hp.com/support/lj1020 for current information.
2Power reported is highest value measured for printing using all standard voltages. HP LaserJet 1010 printer print speed is 12 ppm (letter size) and 12 ppm (A4 size). HP LaserJet 1012, 1015, and 1020 printer print speed is 15 ppm (letter size) and 14 ppm (A4 size).
10 Chapter 1 Product Information |
ENWW |
Table 1-6 Acoustic emissions12
Sound power level |
Declared per ISO 9296 |
|
|
Printing |
LWAd = 6.2 Bels (A) [62 dB (A)] |
|
|
Ready |
Inaudible |
|
|
Sound pressure level—Bystander position |
Declared per ISO 9296 |
|
|
Printing |
LpAm = 49 dB (A) |
|
|
Ready |
Inaudible |
1Values are subject to change. See www.hp.com/support/lj1010 for current information. Configuration tested: HP LaserJet 1010 printer using the standard tray, A4 paper, and simplex, continuous printing. HP LaserJet 1010 printer print speed is 12 ppm (letter size) and 12 ppm (A4 size). HP LaserJet 1012 and 1015 printer print speed is 15 ppm (letter size) and 14 ppm (A4 size).
2Values are subject to change. See www.hp.com/support/lj1020 for current information. Configuration tested: HP LaserJet 1020 printer using the standard tray, A4 paper, and simplex, continuous printing. During other operations, acoustic emissions might vary.
ENWW |
Product specifications 11 |
In most countries/regions, HP Care Pack provides additional coverage, beyond standard warranty for the HP device and for all HP-supplied internal components. This hardware maintenance can uplift the standard warranty, for example, from next-day to same-day service, or extend it up to 5 years. The HP Care Pack can provide Express Exchange or onsite service. For more information, see the support flyer that came with the device for the appropriate phone numbers and information.
12 Chapter 1 Product Information |
ENWW |
The print cartridge is designed to simplify replacement of the major consumable parts. The print cartridge contains the printing mechanism and a supply of toner.
The standard print-cartridge life is 2,000 pages, in accordance with ISO/IEC 19752.
NOTE Actual print cartridge life depends on specific usage.
While Hewlett-Packard does not prohibit the use of refilled print cartridges during the warranty period or while the product is under a maintenance contract, use of refilled cartridges is not recommended for the following reasons:
■Repairs resulting from the use of refilled cartridges are not covered under Hewlett-Packard warranty or maintenance contracts.
■Hewlett-Packard has no control or process to ensure that a refilled cartridge functions at the high level of reliability of a new HP LaserJet print cartridge. Hewlett-Packard also cannot predict the longterm reliability effect on the product from using the different toner formulations that are found in refilled cartridges.
■The print quality of HP LaserJet print cartridges influences the customer’s perception of the product. Hewlett-Packard has no control over the actual print quality of a refilled cartridge.
■Parts that are critical to print quality might not be replaced when the cartridge is refilled with toner.
In order to reduce waste, Hewlett-Packard offers a recycling program. Cartridge components that do not wear out are recycled. Plastics and other materials are recycled. Hewlett-Packard pays the shipping costs from the user to the recycling plant (within the United States). To join this recycling effort, follow the instructions inside the print cartridge box. See www.hp.com/recycle for more information.
ENWW |
Print-cartridge information 13 |
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy. If it is not installed and used in accordance with the instructions, it may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
■Reorient or relocate the receiving antenna.
■Increase separation between equipment and receiver.
■Connect equipment to an outlet on a circuit different from that to which the receiver is located.
■Consult your dealer or an experienced radio/TV technician.
NOTE Any changes or modifications to the printer that are not expressly approved by HewlettPackard could void the user's authority to operate this equipment. Use of a shielded interface cable is required to comply with the Class B limits of Part 15 of FCC rules.
Complies with Canadian EMC Class B requirements.
«Conforme á la classe B des normes canadiennes de compatibilité électromagnétiques. «CEM».»
14 Chapter 1 Product Information |
ENWW |
LASERTURVALLISUUS
LUOKAN 1 LASERLAITE
KLASS 1 LASER APPARAT
HP LaserJet 1010, HP LaserJet 1012, HP LaserJet 1015, HP LaserJet 1020-laserkirjoitin on käyttäjän kannalta turvallinen luokan 1 laserlaite. Normaalissa käytössä kirjoittimen suojakotelointi estää lasersäteen pääsyn laitteen ulkopuolelle. Laitteen turvallisuusluokka on määritetty standardin EN 60825-1 (1994) mukaisesti.
VAROITUS!
Laitteen käyttäminen muulla kuin käyttöohjeessa mainitulla tavalla saattaa altistaa käyttäjän turvallisuusluokan 1 ylittävälle näkymättömälle lasersäteilylle.
VARNING!
Om apparaten används på annat sätt än i bruksanvisning specificerats, kan användaren utsättas för osynlig laserstrålning, som överskrider gränsen för laserklass 1.
HUOLTO
HP LaserJet 1010, HP LaserJet 1012, HP LaserJet 1015, HP LaserJet 1020 -kirjoittimen sisällä ei ole käyttäjän huollettavissa olevia kohteita. Laitteen saa avata ja huoltaa ainoastaan sen huoltamiseen koulutettu henkilö. Tällaiseksi huoltotoimenpiteeksi ei katsota väriainekasetin vaihtamista, paperiradan puhdistusta tai muita käyttäjän käsikirjassa lueteltuja, käyttäjän tehtäväksi tarkoitettuja ylläpitotoimia, jotka voidaan suorittaa ilman erikoistyökaluja.
VARO!
Mikäli kirjoittimen suojakotelo avataan, olet alttiina näkymättömälle lasersäteilylle laitteen ollessa toiminnassa. Älä katso säteeseen.
VARNING!
Om laserprinterns skyddshölje öppnas då apparaten är i funktion, utsättas användaren för osynlig laserstrålning. Betrakta ej strålen. Tiedot laitteessa käytettävän laserdiodin säteilyominaisuuksista:
Aallonpituus 785-800 nm
Teho 5 mW
Luokan 3B laser
ENWW |
Regulatory information 15 |
16 Chapter 1 Product Information |
ENWW |
This chapter provides an overview of the appropriate operating environment, describes the control panel, describes media requirements, and describes how to load print media.
●Operating environment
●Identifying the control-panel components
●Media specifications
●Guidelines for using media
●Loading media
●Setting media types
ENWW |
17 |
Place the product on a sturdy, level surface in a well-ventilated area that meets the following environmental requirements:
■Temperature: 10° to 32.5°C (50° to 90.5°F)
■Humidity: 20 to 80% relative humidity (no condensation)
■Away from direct sunlight, open flames, and ammonia fumes
■With sufficient space around the product to accommodate access and ventilation requirements
370 mm (14.6 inches)
209 mm (8.2 inches)
242 mm (9.5 inches)
Figure 2-1 HP LaserJet 1010 series printer dimensions
Figure 2-2 HP LaserJet 1020 printer dimensions
18 Chapter 2 Installation and operation |
ENWW |