4-233-885-13(1)
Integrated
Stereo Amplifier
Operating Instructions |
GB |
Mode d’emploi |
FR |
Bedienungsanleitung |
DE |
Manual de instrucciones |
ES |
TA-FE570
TA-FE370
© 2001 Sony Corporation
WARNING
To prevent fire or shock hazard, do not expose the unit to rain or moisture.
To avoid electrical shock, do not open the cabinet. Refer servicing to qualified personnel only.
Do not install the appliance in a confined space, such as a bookcase or build-in cabinet.
Install this system so that the power cord can be unplugged from the wall socket immediately in the event of trouble.
To prevent fire, do not Cover the ventilation of the apparatus with news papers, table-cloths, curtains, etc. And don’t place lighted candles on the apparatus.
To prevent fire or shock hazard, do not place objects filled with liquids, such as vases, on the apparatus.
Don’t throw a battery, dispose it as the injurious wastes.
Precautions
On safety
•Do not disassemble the cabinet as this may result in an electrical shock. Refer servicing to qualified personnel only.
•Should any solid object or liquid fall into the cabinet, unplug the amplifier and have it checked by qualified personnel before operating it any further.
On power sources
•Before operating the amplifier, check that the operating voltage of the amplifier is identical with your local power supply. The operating voltage is indicated on the nameplate at the rear of the amplifier.
•The unit is not disconnected from the AC power source (mains) as long as it is connected to the wall outlet, even if the unit itself has been turned off.
•If you are not going to use the amplifier for a long time, be sure to disconnect the amplifier from the wall outlet. To disconnect the AC power cord (mains lead), grasp the plug itself; never pull the cord.
•AC power cord must be changed only at the qualified service shop.
2GB
On placement
•Place the amplifier in a location with adequate ventilation to prevent heat built-up and prolong the life of the amplifier.
•Do not place the amplifier near heat sources, or in a place subject to direct sunlight, excessive dust or mechanical shock.
•Do not place anything on top of the cabinet that might block the ventilation holes and cause malfunctions.
On operation
Before connecting other components, be sure to turn off and unplug the amplifier.
On cleaning the amplifier
Clean the cabinet, panel and controls with a soft cloth slightly moistened with a mild detergent solution. Do not use any type of abrasive pad, scouring powder or solvent such as alcohol or benzine.
On the prevention of howling
Do the following:
–lower the volume.
–keep the turntable as far from the speakers as possible.
–use commercially available audio insulators on the bottom of the turntable.
–keep the microphone away from the speakers during use.
For further protection against howling, set the speakers or turntable on top of a heavy wooden board or concrete slab.
If you have any questions or problems concerning your amplifier, please consult your nearest Sony dealer.
About This Manual
The instructions in this manual are for models TA-FE570 and TA-FE370. Check your model number by looking at the rear panel of your amplifier. The TA-FE570 is the model used for illustration purposes unless stated otherwise.
Any difference in operation is clearly indicated in the text, for example, “TA-FE570 only.”
Type of differences
Feature |
FE570 |
FE370 |
EON reception |
z |
|
|
|
|
Tape monitor function |
z |
|
|
|
|
Switched AC outlets |
z* |
z* |
* Except for U.K. model.
Tip
Instructions in this manual describe the controls on the amplifier.
For details on the remote buttons control, see “Remote button descriptions” on page 11.
Table of Contents |
|
Parts Identification |
|
Main unit ............................................... |
4 |
Getting Started |
|
Unpacking ............................................. |
5 |
Hookup overview .................................. |
5 |
Audio component hookups .................... |
6 |
Speaker system hookups ....................... |
7 |
Mains lead hookups ............................... |
7 |
Basic Operations |
|
Listening to the music ........................... |
8 |
Recording .............................................. |
9 |
Additional Information |
|
Troubleshooting ................................... |
10 |
Specifications ...................................... |
10 |
Remote button descriptions ................. |
11 |
3GB
Parts Identification
The items are arranged in alphabetical order.
Refer to the pages indicated in parentheses ( ) for details.
Main unit
1 2 3 |
4 |
5 |
|||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
qf qd qs qa 0 9 8 7 6
BALANCE 8 (8) BASS 0 (8)
EON LINK (TA-FE570 only) qd (8) INPUT SELECTOR 4 (8, 9) LOUDNESS 6 (8)
PHONES jack qf (8) SOURCE DIRECT 7 (8) SPEAKERS selector qa (8) STANDBY indicator 1
TAPE1 MONITOR (TA-FE570 only) qs (9) TREBLE 9 (8)
VOLUME control 5 (8) ?/1 (power) 2 (8, 9)
(remote control sensor) 3 (5)
4GB
Getting Started
Unpacking
Check that you have received the following supplied items:
•Remote commander (remote) RM-S325 (1)
•Sony batteries R6 (size-AA) (2)
Inserting batteries into the remote
Insert two R6 (size-AA) batteries, matching the + and – on the batteries with the markings inside the battery compartment. When using the remote, point it at the remote control sensor
on the amplifier.
Tip
With normal use, the batteries should last for about 6 months. When the remote no longer operates the amplifier, replace all the batteries.
Notes
•Do not leave the remote near an extremely hot or humid place.
•Do not drop any foreign object into the remote casing, particularly when replacing the batteries.
•Do not expose the remote sensor to direct sunlight or lighting equipment. Doing so may cause a malfunction.
•If you don’t use the remote for an extended period of time, remove the batteries to avoid possible damage from battery leakage and corrosion.
Hookup overview
The amplifier allows you to connect and control the following audio components. Follow the hookup procedure indicated for each component that you want to connect.
DAT deck |
Tape deck |
Tuner |
|
|
|
|
|
|
MD deck |
Turntable |
CD player |
|
|
|
Speaker (L) |
|
Speaker (R) |
|
|
|
Before you get started
•Turn off the power to all components before making any connections.
•Do not connect the mains leads of the various components until all connections are completed.
•Use the audio connecting cords supplied with each component for hooking up with the amplifier. Purchase and use optionally available cords as required.
•Be sure to make connections firmly to prevent hum and noise.
•When connecting an audio connecting cord, be sure to match the R (right) and L (left) jacks of the amplifier to the R and L jacks on the other components.
Started Identification/Getting Parts
5GB
Audio component hookups
Overview
Here you learn how to connect your audio components to the amplifier.
UTUNER AUX TAPE1/DAT
AC OUTLET
SWITCHED 100W MAX
SIGNAL GND U |
|
|
|
|
SPEAKERS |
|
Ω |
|
|
|
|
|
|
R |
L |
|
|
|
|
|
|
|
IMPEDANCE USE 4 - 16 |
|
|
|
|
|
|
|
|
+ |
|
+ |
|
PHONO TUNER |
CD |
AUX |
TAPE2/MD |
TAPE1/DAT |
|
|
|
|
IN |
IN |
IN |
IN |
RECOUT IN |
RECOUT IN |
|
|
|
L |
|
|
|
|
|
|
|
EON CONTROL |
|
|
|
|
|
– |
|
– |
IN |
R |
|
|
|
|
|
|
||
|
|
|
|
|
|
|
|
|
PHONO CD TAPE2/MD
EON CONTROL IN (TA-FE570 only)
What cords will I need?
Audio connecting cord (not supplied) (2 for each tape deck, DAT deck, or MD deck; 1 for other components)
White (L) |
White (L) |
Red (R) |
Red (R) |
Hookups
The arrow l indicates signal flow.
Note
The jacks on the TA-FE570 are shown in the following illustrations.
CD player
Amplifier |
|
CD Player |
CD |
|
OUTPUT |
IN |
|
LINE |
L |
l |
L |
|
|
|
R |
|
R |
Tuner |
|
|
Amplifier |
|
Tuner |
TUNER |
|
OUTPUT |
IN |
|
LINE |
L |
l |
L |
|
|
|
R |
|
R |
Tape deck, DAT deck, or MD deck
Amplifier |
Tape deck |
|
TAPE1/DAT |
OUTPUT |
INPUT |
OUT IN |
LINE |
LINE |
L |
l |
L |
|
|
|
R |
|
R |
l
Use the configuration above to connect the OUTPUT and INPUT jacks of:
–a tape deck or DAT deck to the TAPE1/DAT jacks.
–a tape deck or MD deck to the TAPE2/MD jacks.
Turntable
Amplifier |
Turntable |
PHONO |
|
IN |
|
L |
l |
|
|
R |
|
Note
To prevent hum, connect the earth lead to SIGNAL GND (U) on the amplifier.
EON CONTROL (TA-FE570 only)
Amplifier |
Tuner |
EON CONTROL |
EON CONTROL |
IN |
OUT |
|
l |
If your tuner is equipped with an EON CONTROL OUT terminal, connect it to the EON CONTROL IN terminal on the amplifier to allow use of the EON (Enhanced Other Networks) function of the RDS (Radio Data System) (see page 8).
6GB
Speaker system hookups |
Mains lead hookups |
Overview
Here you learn how to connect speakers to the amplifier. Before connecting, remove the caps from the speaker terminals.
SPEAKERS
AC OUTLET
SWITCHED 100W MAX
SIGNAL GND U |
|
|
|
|
|
SPEAKERS |
Ω |
|
|
|
|
|
|
R |
L |
|
|
|
|
|
|
|
IMPEDANCE USE 4 - 16 |
|
|
|
|
|
|
|
|
+ |
|
+ |
|
PHONO TUNER |
CD |
AUX |
TAPE2/MD |
TAPE1/DAT |
|
|
|
|
IN |
IN |
IN |
IN |
RECOUT IN |
RECOUT IN |
|
|
|
L |
|
|
|
|
|
|
|
EON CONTROL |
|
|
|
|
|
– |
|
– |
IN |
|
|
|
|
|
|
|
||
R
What cords will I need?
Speaker cord (not supplied) (1 for each speaker)
(+) |
(+) |
(–) 
(–)
Twist the stripped ends of the cord about
15 mm. Be sure to match the speaker cord to the appropriate terminal on the components: + to + and – to –. If the cords are reversed, the sound will be distorted and will lack bass.
Hookups
] ] 
} 
}
AC OUTLET
SWITCHED 100W MAX
SIGNAL GND y |
|
|
|
|
|
SPEAKERS |
Ω |
|
|
|
|
|
|
R |
L |
|
|
|
|
|
|
|
IMPEDANCE USE 4 - 16 |
|
|
|
|
|
|
|
|
+ |
|
+ |
|
PHONO TUNER |
CD |
AUX |
TAPE2/MD |
TAPE1/DAT |
|
|
|
|
IN |
IN |
IN |
IN |
RECOUT IN |
RECOUT IN |
|
|
|
L |
|
|
|
|
|
|
|
EON CONTROL |
|
|
|
|
|
– |
|
– |
IN |
|
|
|
|
|
|
|
||
R
b
To a wall outlet
Connecting the mains lead
Connect the mains lead from this amplifier and from your audio/video components to wall outlets.
Tip
You can power other components through AC OUTLET on the amplifier (except for U.K. model). By connecting other audio components to AC OUTLET on the amplifier, you can supply power to the connected components through the amplifier and turn them all on or off when you turn the amplifier on or off.
Caution
Make sure that the total power consumption of all components connected to the outlets on the amplifier does not exceed 100 watts. Do not connect electrical home appliances such as an electric iron, fan, TV, or other high-wattage appliances to these outlets.
Note
Separate the mains lead, audio connecting cords and speaker cords. Noise or sound deterioration may occur when audio connecting cords are in contact with the mains lead, or when the mains lead or speaker cords are placed near the tuner’s loop aerial or aerial wire.
Started Getting
7GB
Basic Operations
Listening to the music
1 Press ?/1 to turn on the amplifier and turn VOLUME fully anticlockwise to prevent damaging the speakers with excessive output.
2 Turn on the programme source you want to listen to.
3 Turn INPUT SELECTOR to select the respective programme source.
To listen to a |
Select |
Record |
PHONO |
|
|
Radio broadcast |
TUNER |
|
|
Compact disc |
CD |
|
|
Source connected to AUX |
AUX |
|
|
Source connected to: |
|
– TAPE1/DAT |
TAPE1/DAT |
– TAPE2/MD |
TAPE2/MD |
|
|
4 Start the programme source.
5 Adjust the volume by turning VOLUME.
To |
Press or turn |
Adjust the bass |
BASS |
|
|
Adjust the treble |
TREBLE |
|
|
Adjust the balance |
BALANCE |
|
|
Reinforce the bass and treble |
LOUDNESS |
at low listening level |
|
|
|
Tips
•If ?/1 is pressed down, you can turn the amplifier on and off by pressing ?/1 on the remote.
•To listen through the headphones, connect the headphones to PHONES and set SPEAKERS to OFF.
•To listen directly to the input signal, press SOURCE DIRECT so that the indicator lights up. Since the circuits of TONE controls, BALANCE control, and LOUDNESS button are bypassed, you cannot adjust bass, treble, the balance, reinforce the bass and treble while listening to a source directly.
Note
Avoid high speaker output at which the sound is distorted. High-frequency distortion may damage the tweeters.
To receive the Enhanced Other Networks (EON) programmes
(TA-FE570 only)
“Enhanced Other Networks (EON)” is one of the convenient RDS services. This allows the unit to automatically switch to a programme type of your choice when one starts in your broadcast area.
When your amplifier is connected to a Sony tuner with the EON CONTROL system, the amplifier switches to any EON programme that is broadcast in your EON area, and switches back to the last selected programme source when the programme ends.
1 Make sure that the amplifier and the tuner are connected through the EON CONTROL terminals (see page 6).
2 Press EON LINK so that the indicator lights up.
Whenever an EON programme starts on the radio frequency that your tuner is set to, you will receive it.
To cancel EON reception
Press EON LINK again so that the indicator goes off.
Notes
•If you select another programme source while receiving an EON programme, EON reception ends. However, as long as the EON LINK indicator lights up, you can receive EON programmes automatically.
•Make sure to cancel EON reception before starting to record since an EON programme may interfere with your recording.
•If you activate the Tape Monitor function (see page
9)while the EON LINK indicator is lit, the indicator goes off and you cannot receive EON programmes. If this happens, deactivate the Tape Monitor function so that the indicator lights up again.
8GB
Recording
1 Press ?/1 to turn on the amplifier.
2 Turn on the programme source you want to record.
3 Turn INPUT SELECTOR to select the programme source you want to record.
To record a |
Select |
Record |
PHONO |
|
|
Radio broadcast |
TUNER |
|
|
Compact disc |
CD |
|
|
Source connected to AUX |
AUX |
Source connected to: |
|
– TAPE1/DAT |
TAPE1/DAT |
– TAPE2/MD |
TAPE2/MD |
|
|
4 Prepare the recording component for recording, then start recording.
5 Start playing the programme source.
Tips
•You can record the same source on two recording components at the same time
•You can monitor the recorded sound if the tape deck you are recording on has separate playback and recording heads (Tape Monitor function)
(TA-FE570 only).
To monitor the sound, press TAPE1 MONITOR.
Note that you can monitor the only sound being recorded from the TAPE1/DAT jacks.
Operations Basic
9GB
Additional Information
Troubleshooting
If you experience any of the following difficulties while using the amplifier, use this troubleshooting guide to help you remedy the problem. Should any problem persist, consult your nearest Sony dealer.
No sound output.
•Connect the audio connecting cords firmly.
•Connect the amplifier and other audio components correctly.
•Turn INPUT SELECTOR to the appropriate programme source.
•Set SPEAKERS to ON.
No audio from one channel or unbalanced speaker output.
•Turn BALANCE to adjust the balance.
•Check the speaker and input connections of silent channel.
Weak bass or treble.
•Adjust the TONE controls.
•Change speaker positions or room conditions to eliminate obstructions in sound path.
Distorted sound.
•Improperly selected input signal.
•Insufficient input capacity of speakers. Lower the volume.
Lack of bass or ambiguity in instrument positions.
• Speaker cord and terminal polarity are reversed. Reconnect the cords with correct polarity.
Hum or noise.
•Ground the turntable system (see page 6).
•Connect the audio connecting cords firmly.
•The amplifier is picking up interference from a TV set. Move the amplifier away from the TV set or turn the TV set off.
The remote does not function.
•Remove any obstructions between the remote control sensor on the amplifier and the remote.
•Point the remote towards the remote sensor on the front of the amplifier.
•The remote is too far from the amplifier. Move closer to the amplifier.
•Replace the batteries in the remote.
Sudden loss of audio.
• Check if a short-circuit has occurred. Turn off the amplifier and check the connected components and speakers.
Specifications
Amplifier section
DIN power output |
|
TA-FE570: |
110 W + 110 W |
|
(4 ohms at 1 kHz) |
TA-FE370: |
70 W + 70 W |
|
(4 ohms at 1 kHz) |
Frequency response
PHONO (20 Hz - 20 kHz): RIAA equalization curve ±1.0 dB
TUNER, CD, AUX, TAPE1/DAT, TAPE2/MD: 7 Hz - 70 kHz +–30 dB
S/N (network A)
PHONO: 80 dB
TUNER, CD, AUX, TAPE1/DAT, TAPE2/MD: 105 dB
Output voltage/impedance
RECOUT: |
200 mV, 1 kilohm |
PHONES: |
5 mW (at 8 ohms) |
Speakers impedance |
4 - 16 ohms |
Damping factor |
80 (8 ohms, 1 kHz) |
10GB
General
System
Power amplifier with all stages directly coupled Preamplifier: Low-noise, equalizer
amplifier
Power requirements |
230 V AC, 50/60 Hz |
Power consumption |
|
TA-FE570: |
190 W |
TA-FE370: |
160 W |
|
0.6 W |
|
(In standby mode) |
Dimensions (approx.) (w/h/d)
430 x 135 x 310 mm incl. projecting parts and controls
Mass (approx.) |
|
TA-FE570: |
6.5 kg |
TA-FE370: |
5.5 kg |
Supplied accessories
Remote commander (remote) RM-S325 (1) Sony batteries R6 (size-AA) (2)
Design and specifications are subject to change without notice.
Remote button
descriptions
You can use the supplied remote to control other Sony audio components equipped with the (remote control sensor) mark.
Remote |
Component |
Function |
button(s) |
|
|
|
|
|
?/1 |
Amplifier |
Turns the amplifier on |
|
|
and off. |
|
|
|
FUNCTION |
|
|
CD |
Amplifier |
Selects input signals from |
|
|
the CD jacks. |
|
|
|
TUNER |
Amplifier |
Selects input signals from |
|
|
the TUNER jacks. |
|
|
|
PHONO |
Amplifier |
Selects input signals from |
|
|
the PHONO jacks. |
|
|
|
TAPE1/DAT Amplifier |
Selects input signals from |
|
|
|
the TAPE1/DAT jacks. |
|
|
|
TAPE2/MD |
Amplifier |
Selects input signals from |
|
|
the TAPE2/MD jacks. |
|
|
|
AUX |
Amplifier |
Selects input signals from |
|
|
the AUX jacks. |
|
|
|
TUNER |
|
|
PRESET +/– Tuner |
Scans and selects preset |
|
|
|
stations. |
|
|
|
CD |
|
|
N |
CD player |
Starts playback. |
|
|
|
X |
CD player |
Pauses playback. |
|
|
|
x |
CD player |
Stops playback. |
|
|
|
./> |
CD player |
Locates tracks (AMS*). |
|
|
|
D.SKIP |
CD player |
Skips a disc (for CD |
|
|
player equipped with a |
|
|
multi-disc changer). |
|
|
|
MD |
|
|
N |
MD deck |
Starts playback. |
|
|
|
X |
MD deck |
Pauses playback. |
|
|
|
x |
MD deck |
Stops playback. |
|
|
|
./> MD deck |
Locates tracks. |
|
|
|
|
TAPE DECK A/B |
|
|
n/N |
Deck A or B Starts playback. |
|
|
|
|
x |
Deck A or B Stops all tape operations. |
|
|
|
|
m/M |
Deck A or B Fast-forwards or rewinds |
|
|
|
the tape. |
|
|
|
VOL +/– |
Amplifier |
Controls the volume. |
|
|
|
* Automatic Music Sensor
Information Additional
11GB
AVERTISSEMENT
Afin d’éviter tout risque d’incendie ou d’électrocution, ne pas exposer cet appareil à la pluie ou à l’humidité.
Afin d’écarter tout risque d’électrocution, garder le coffret fermé. Ne confier l’entretien de l’appareil qu’à un personnel qualifié.
N’installez pas l’appareil dans un espace confiné comme dans une bibliothèque ou un meuble encastré.
Installez cette chaîne en veillant à ce que le cordon d’alimentation puisse être immédiatement débranché de la prise secteur en cas de problème.
Afin d’éviter tout risque d’incendie, ne pas couvrir les ailettes de ventilation de cet appareil avec des papiers journaux, des nappes, des rideaux, etc. Ne pas poser de bougies allumées sur l’appareil.
Afin d’éviter tout risque d’incendie et d’électrocution, ne pas poser d’objets remplis de liquide, vases ou autres, sur l’appareil.
Ne pas jeter les piles. Les déposer aux endroits prévus à cet effet.
Précautions
Sécurité
•Afin d’éviter tout choc électrique, n’ouvrez pas le coffret. Confiez l’entretien de l’amplificateur à un professionnel.
•Si un objet ou un liquide tombait dans l’amplificateur, débranchez celui-ci et faites-le vérifier par un professionnel avant de le remettre en marche.
Sources d’alimentation
•Avant de mettre l’amplificateur sous tension, vérifiez si sa tension de fonctionnement correspond à celle du secteur local. La tension de fonctionnement est indiquée sur la plaque signalétique à l’arrière de l’amplificateur.
•Cet amplificateur n’est pas isolé de la source d’alimentation (secteur) tant qu’il reste raccordé à une prise secteur, même s’il a été éteint.
•Débranchez l’amplificateur de la prise murale s’il doit rester inutilisé pendant une période prolongée. Pour débrancher le cordon d’alimentation secteur, tirez sur la fiche, jamais sur le cordon proprement dit.
•Le cordon d’alimentation secteur doit être remplacé par un professionnel.
Installation
•Installez l’amplificateur à un endroit suffisamment aéré pour éviter toute surchauffe interne et prolonger sa durée de vie.
•N’installez pas l’amplificateur près d’une source de chaleur, ou bien à un endroit exposé en plein soleil,
2FR |
à une poussière excessive ou à des chocs |
|
mécaniques. |
•Ne posez rien sur l’amplificateur qui pourrait obstruer les ailettes de ventilation ou provoquer une panne.
Fonctionnement
Avant de raccorder d’autres appareils, mettez l’amplificateur hors tension et débranchez-le.
Nettoyage de l’amplificateur
Nettoyez le coffret, le panneau et les commandes avec un chiffon doux, légèrement humidifié d’une solution détergente douce. N’utilisez pas de tampon abrasif, de poudre à récurer ni de solvant, comme l’alcool ou l’essence.
Pour éviter un effet Larsen
–Réduisez le volume.
–Éloignez le tourne-disque le plus possible des enceintes.
–Mettez des isolateurs audio en vente dans le commerce sous le tourne-disque.
–Maintenez le microphone éloigné des enceintes pendant l’utilisation.
Pour une meilleure protection contre l’effet
Larsen, installez les enceintes ou le tourne-disque sur une planche de bois épaisse ou une dalle de béton.
Pour toute question ou problème au sujet de cet appareil, veuillez contacter votre revendeur Sony agréé.
A propos de ce mode d’emploi
Les instructions de ce mode d’emploi concernent les modèles TA-FE570 et TA-FE370. Vérifiez le numéro de votre modèle sur le panneau arrière de l’amplificateur. Le TA-FE570 est le modèle utilisé dans les illustrations, sauf spécification contraire. Toute différence de fonctionnement est clairement indiquée dans le texte, par exemple “TA-FE570 seulement”.
Différences entre les modèles
Caractéristiques |
FE570 |
FE370 |
Réception EON |
z |
|
|
|
|
Contrôle du son enregistré |
z |
|
|
|
|
Prises secteur commutées z* |
z* |
|
|
|
|
* Sauf modèle pour le Royaume-Uni. |
|
|
Conseil
Les instructions dans ce mode d’emploi décrivent les commandes de l’amplificateur.
Pour les touches de la télécommande, voir “Description des touches de la télécommande”, page 11.
Table Des Matières
Nomenclature
Appareil principal .................................. |
4 |
Préparatifs
Déballage ............................................... |
5 |
Raccordements ...................................... |
5 |
Raccordement d’appareils audio ........... |
6 |
Raccordement des enceintes .................. |
7 |
Raccordement du cordon d’alimentation |
|
secteur ............................................. |
7 |
Opérations de base
Ecoute d’une source sonore ................... |
8 |
|
|
|
FR |
||
Enregistrement ....................................... |
9 |
|
|
|
|
|
|
Informations |
|
|
|
complémentaires |
|
|
|
Guide de dépannage ............................ |
10 |
|
|
Spécifications ...................................... |
10 |
|
|
Description des touches de la |
|
|
|
télécommande ............................... |
11 |
|
|
3FR
Nomenclature
Les éléments de la chaîne sont indiqués dans l’ordre alphabétique.
Reportez-vous aux pages entre parenthèses ( ) pour le détail.
Appareil principal
1 2 3 |
4 |
5 |
|||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
qf qd qs qa 0 9 8 7 6
BALANCE 8 (8) BASS 0 (8)
Commande VOLUME 5 (8)
EON LINK (TA-FE570 seulement) qd (8) Indicateur STANDBY 1
INPUT SELECTOR 4 (8, 9) LOUDNESS 6 (8)
Prise PHONES qf (8) Sélecteur SPEAKERS qa (8) SOURCE DIRECT 7 (8)
TAPE1 MONITOR (TA-FE570 seulement) qs (9) TREBLE 9 (8)
?/1 (alimentation) 2 (8, 9) 
(capteur de télécommande) 3 (5)
4FR
Loading...