3-865-267-11(1)
Compact Hi-Fi
Stereo System
Operating Instructions
Owner’s Record
The model and serial numbers are located on the rear panel. Record the serial number in the space provided below. Refer to them whenever you call upon your Sony dealer regarding this product.
|
|
Model No. |
|
Serial No. |
|
|
|
|
|
|
|
|
|
|
LBT-D390 LBT-XB44K
LBT-D790 LBT-XB50
LBT-G5500 LBT-XB60
LBT-XB33 LBT-XB66
LBT-XB33K LBT-XB66K
LBT-XB44 LBT-XB660
©1998 by Sony Corporation
WARNING
To prevent fire or shock hazard, do not expose the unit to rain or moisture.
To avoid electrical shock, do not open the cabinet. Refer servicing to qualified personnel only.
Do not install the appliance in a confined space, such as a bookcase or built-in cabinet.
Laser component in this product is capable of emitting radiation exceeding the limit for Class 1.
This appliance is classified as a CLASS 1 LASER product. The CLASS 1 LASER PRODUCT MARKING is located on the rear exterior.
This caution label is located inside the unit.
NOTICE FOR THE CUSTOMERS IN THE U.S.A.
This symbol is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
This symbol is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.
CAUTION
The use of optical instruments with this product will increase eye hazard.
INFORMATION
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
–Reorient or relocate the receiving antenna.
–Increase the separation between the equipment and receiver.
–Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
–Consult the dealer or an experienced radio/TV technician for help.
CAUTION
You are cautioned that any changes or modifications not expressly approved in this manual could void your authority to operate this equipment.
Note on CATV system installer:
This reminder is provided to call CATV system installer’s attention to Article 820–40 of the NEC that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as practical.
NOTICE FOR THE CUSTOMERS IN CANADA
CAUTION:
TO PREVENT ELECTRIC SHOCK, DO NOT USE THIS POLARIZED AC PLUG WITH AN EXTENSION CORD,
RECEPTACLE OR OTHER OUTLET UNLESS THE BLADES CAN BE FULLY INSERTED TO PREVENT BLADE EXPOSURE.
This stereo system is equipped with the Dolby* B- type noise reduction system.
* Dolby noise reduction manufactured under license from Dolby Laboratories Licensing Corporation. “DOLBY” and the double-D symbol aare trademarks of the Dolby Laboratories Licensing Corporation.
(LBT-XB50/XB60 only)
2
Table of Contents |
|
Getting Started |
|
Step 1: Hooking up the system ............ |
4 |
Step 2: Setting the time ......................... |
6 |
Step 3: Presetting radio stations .......... |
7 |
Connecting optional AV |
|
components ...................................... |
8 |
Sound Adjustment |
|
Adjusting the sound ............................ |
28 |
Selecting the audio emphasis ............. |
29 |
Adjusting the audio emphasis ............ |
30 |
Making a personal audio emphasis |
|
file .................................................... |
31 |
Basic Operations |
|
Playing a CD ......................................... |
11 |
Recording a CD .................................... |
13 |
Listening to the radio ........................... |
14 |
Recording from the radio .................... |
15 |
Playing a tape ........................................ |
16 |
Recording from a tape ......................... |
18 |
The CD Player |
|
Using the CD display ........................... |
19 |
Playing CD tracks repeatedly ............. |
19 |
Playing CD tracks in random |
|
order ................................................ |
20 |
Programming CD tracks ..................... |
21 |
Playing CDs without interruption ..... |
22 |
The Tape Deck |
|
Recording on a tape manually ........... |
23 |
Recording CDs by specifying the track |
|
order ................................................ |
24 |
DJ Effects |
|
Looping part of a CD ........................... |
26 |
Flashing part of a CD ........................... |
26 |
Waving the equalizer ........................... |
27 |
Other Features |
|
Using the Radio Data System |
|
(RDS)* .............................................. |
32 |
Singing along: Karaoke ...................... |
34 |
Falling asleep to music ........................ |
36 |
Waking up to music ............................. |
37 |
Timer-recording radio programs ....... |
38 |
Additional Information |
|
Precautions ............................................ |
40 |
Troubleshooting ................................... |
41 |
Specifications ........................................ |
43 |
Index ....................................................... |
46 |
* For European model only – excluding Russia
Notice for customers in the United Kingdom
The AC power cord has been fixed on the rear panel with the plug band temporarily for shipment.
Unlock the plug band to remove the plug.
Back panel
Plug band
F
ES
P
3
Getting Started
Step 1: Hooking up the system
Follow steps 1through 5to hook up your system using the supplied cords and accessories.
AM loop antenna
Right speaker |
FM antenna |
Left speaker |
5
2
|
3 |
1 |
1 |
1 |
4 |
The above illustration is of the LBT-XB66K.
1Connect the speakers. |
2 Insert only the stripped portion of the |
1 Connect the speaker cords to |
cord. Inserting the vinyl portion will |
SPEAKER jacks of the same color. |
interfere with the speaker connection |
Keep the speaker cords away from the |
and no sound will come from the |
antennas to prevent noise. |
speaker. |
R |
|
Note |
|
|
The speakers for LBT-D390/G5500/XB33/XB33K/ |
||
+ |
|
||
L |
XB50 do not have the speaker jacks. |
||
|
|||
|
+ |
Connect the speaker cords to the speaker jacks on |
|
|
the unit. |
||
|
|
||
|
– |
|
|
Red* (‘) Black* (’) |
|
|
*The color of your speaker cords might be different. See the speakers’ manual for
4 |
details if supplied. |
2Connect the FM/AM antennas.
Set up the AM loop antenna, then connect it.
For European model
Extend the FM wire antenna horizontally.
AM loop antenna
C |
|
|
||
F |
OA |
XIA |
L |
|
M |
||||
|
75 |
|||
|
|
|
AM
4Connect the power cord to a wall outlet.
The demonstration appears in the display.
If the plug on this unit does not fit your wall outlet, detach the supplied adapter from the plug (except for North and South American countries, Europe and Australia).
5Deactivate the demonstration mode by pressing DISPLAY/DEMO while the system is off.
Inserting two size AA (R6) batteries into the remote
For other models
Extend the FM wire antenna horizontally.
AM loop antenna
FM75
AM
3Set VOLTAGE SELECTOR to the position of your local power line voltage (except for North American, European, Mexican, South African, Thailand and Australian models).
VOLTAGE SELECTOR
110-120V 220-240V
Tips
•With normal use, the batteries should last for about six months. When the remote no longer operates the system, replace both batteries with new ones.
•When you set the time, the demonstration is deactivated.
To activate the demonstration again, press DISPLAY/DEMO while the system is off.
Note
If you do not use the remote for a long period of time, remove the batteries to avoid possible damage from battery leakage.
When carrying this system
Do the following to protect the CD mechanism.
1Press FUNCTION repeatedly until “CD” appears in the display.
2Hold down PLAY MODE and press 1/uto turn off the system.
5
Step 2: Setting the time
You must set the time before using the timer functions. The clock is on a 24hour system for the European and Brazilian models, and a 12-hour system for other models.
The 24-hour system model is used for illustration purpose.
4 Press TUNING +/– to set the minutes.
5 Press ENTER/NEXT.
The clock starts.
1 |
3,5 2,4 |
LBT-XB66/XB66K/XB660 only
1 Press t/CLOCK SET.
The hour indication flashes.
LBT-D390/D790/G5500/XB33/XB33K/ XB44/XB44K/XB50/XB60 only
1 Press t/CLOCK SET.
The hour indication flashes.
2 Press TUNING +/– to set the hour.
3 Press ENTER/NEXT.
The minutes indication flashes.
2 Press TUNING +/– to set the hour.
3 Press ENTER/NEXT.
The minutes indication flashes.
4 Press TUNING +/– to set the minutes.
5 Press ENTER/NEXT.
The clock starts.
Tip
If you make a mistake, start over from step 1.
6
Step 3: Presetting radio stations
You can preset the following number of stations:
—2 band model: 20 for FM and 10 for AM
—3 band model: 20 for FM, 10 for MW, and 10 for LW
—4 band model: 20 for FM, 10 for MW, 10 for LW, and 5 for UKV
The bands you can select depend on the kind of tuner built into your system. Confirm the bands by pressing TUNER/BAND repeatedly.
1/u
(Power) 6 4 2 3,5 1
1 Press TUNER/BAND repeatedly until the band you want appears in the display.
Each time you press this button, the band changes as follows:
2 band model: FM ˜AM 3 band model:
FM nMW nLW n
4 band model:
FM nMW nLW nUKV* n
*When you select this band, “STEREO Plus” appears in the display.
2 Press TUNING MODE repeatedly until “AUTO” appears in the display.
3 Press TUNING +/–.
The frequency indication changes and scanning stops when the system tunes in a station. “TUNED” and “STEREO” (for a stereo program) appear.
LBT-D390/D790/G5500/XB33/XB33K/XB44/ XB44K/XB50/XB60
DOLBY NR
OFF
TUNED
STEREO AUTO
ALL DISC S
MHz
LBT-XB66/XB66K/XB660
DOLBY NR |
|
OFF |
AUTO |
TUNED
STEREO
ALL DISC S |
MHz |
4 Press TUNER MEMORY.
A preset number flashes in the display.
LBT-D390/D790/G5500/XB33/XB33K/XB44/ XB44K/XB50/XB60
DOLBY NR
OFF
TUNED
STEREO AUTO
ALL DISC S
LBT-XB66/XB66K/XB660
DOLBY NR |
|
OFF |
AUTO |
TUNED
STEREO
ALL DISC S
5 Press TUNING +/– to select the preset number you want.
LBT-D390/D790/G5500/XB33/XB33K/XB44/ XB44K/XB50/XB60
DOLBY NR
OFF
TUNED
STEREO AUTO
ALL DISC S
LBT-XB66/XB66K/XB660
DOLBY NR |
|
OFF |
AUTO |
TUNED
STEREO
ALL DISC S
6 Press ENTER/NEXT.
The station is stored.
7 Repeat steps 1 through 6 to store other stations.
continued 7
Step 3: Presetting radio stations (continued)
To tune in a station with a weak signal
Press TUNING MODE repeatedly until “MANUAL” appears in step 2, then press TUNING +/– to tune in the station.
To change the preset number
Start over from step 1.
Note
The preset stations are canceled when you disconnect the power cord or if a power failure occurs for half a day.
8
Connecting optional AV components
To enhance your system, you can connect optional components. Refer to the instructions included with each component for details.
Connecting audio components
Connecting a turntable
Be sure to match the color of the plugs and the connectors. To listen to the sound from the connected turntable, press FUNCTION repeatedly until “PHONO” appears.
To the audio output of the turntable
Note
Using the turntable at high volume may cause distortion or howling. This is often caused by the bass sound from the speakers. The bass sound may be picked up by the needle of the turntable, and produce the distortion or howling. To avoid this, do the following:
1 Keep some distance between the speakers and the turntable.
2 Stop using the surround effect.
3 Install the speakers or the turntable on a firm and
stable surface. |
|
4 Press DBFB repeatedly until “DBFB |
” |
disappears from the display (LBT-D390/G5500/ XB33/XB33K/XB50 only).
Press SUPER WOOFER repeatedly until the indicator on this button goes off (except for LBTD390/G5500/XB33/XB33K/XB50).
Connecting an MD deck for digital recording (except for LBT-D390/ D790/G5500)
You can record a CD to an MD digitally by connecting your MD deck using an optical cable.
To the digital input of the MD deck
Connecting an MD deck for analog recording (except for LBT-D390/ D790/G5500)
Be sure to match the color of the plugs and the connectors. To listen to the sound of the connected MD deck, press FUNCTION repeatedly until “MD” appears.
To the audio outputs |
To the audio inputs of |
|||||||
of the MD deck |
the MD deck |
|||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Note
If you cannot select “MD” by pressing FUNCTION, press 1/uwhile pressing FUNCTION when the power is turned off. “VIDEO” will be switched to “MD.” To return to “VIDEO,” do the same procedure.
Connecting surround speakers
(LBT-D790/XB33/XB33K/XB50/XB60 only)
You can connect optional surround speakers.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
To surround |
To surround |
||||
speaker (R) |
speaker (L) |
Note
You need to connect both left and right surround speakers. Otherwise, the sound will not be heard.
Connecting a VCR
Be sure to match the color of the plugs and the connectors. To listen to the sound from the connected VCR, press FUNCTION repeatedly until “VIDEO” appears.
To the audio output of the VCR
continued 9
Connecting optional AV components (continued)
Connecting outdoor antennas
Connect an outdoor antenna to improve the reception.
FM antenna
Connect an optional FM outdoor antenna. You can also use the TV antenna instead.
For European model
IEC standard socket |
|
(not supplied) |
Screw clamp |
AM antenna
Connect a 6 to 15 meter (20 to 50 feet) insulated wire to the AM antenna terminal. Leave the supplied AM loop antenna connected.
For European model
Screw clamp
Insulated wire (not supplied)
C |
|
|
||
F |
OA |
XIA |
L |
|
M |
||||
|
75 |
|||
|
|
|
AM
|
|
|
|
|
C |
|
|
|
|
|
|
|
|
F |
OA |
XIA |
L |
|
|
|
|
|
M |
|||
|
|
|
|
|
|
75 |
||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
AM
Ground wire (not supplied)
For other models
Screw clamp
75-ohm coaxial cable (not supplied)
FM75
AM
Ground wire (not supplied)
Ground wire (not supplied)
For other models
Screw clamp Insulated wire (not supplied)
FM75
AM
Ground wire (not supplied)
Important
If you connect an outdoor antenna, connect a ground wire to the yterminal with the screw clamp. To prevent a gas explosion, do not connect the ground wire to a gas pipe.
10
Basic Operations
Playing a CD
— Normal Play
You can play up to five CDs in a row.
1/u |
|
(Power) |
VOLUME · |
4 |
3 1 2 |
P p |
|||
1/ALL DISCS |
|
|
|
|
|
0 |
1 |
PL |
|
|
) |
|
CS |
AY |
|
||
|
DIS |
|
MO |
||
|
L |
|
|
||
|
/AL |
|
|
DE |
|
|
|
|
|
R |
|
|
TI |
|
|
E |
|
|
D |
|
|
P |
|
|
E |
|
|
E |
|
|
|
|
|
TR |
|
|
AMS |
|
|
|
|
|
Jog dial |
|
DISC SKIP
P p
AMS =/+
0/)
CD (
VOLUME +/–
1 Press 6OPEN and place a CD on the disc tray.
If the disc is not placed properly it will not be recognized.
With the label
side up. |
ª ª |
ª |
ª |
|
|
|
|
When you play |
|
|
|
a CD single, |
|
ª |
|
place it on the |
|
|
|
inner circle of |
|
|
|
the tray. |
|
|
|
2 Press DISC SKIP to place up to four more CDs on the tray.
The disc tray rotates so you can insert other CDs.
3 Close the front cover.
4 Press one of the DIRECT PLAY buttons.
Playback starts.
If you press · (or CD (on the remote), playback starts from the CD in the playing position.
LBT-D390/D790/G5500/XB33/XB33K/XB44/ XB44K/XB50/XB60
Disc number in the playing position Track number
DOLBY NR
OFF
ALL DISC S
Elapsed time
LBT-XB66/XB66K/XB660
Disc number in the playing position Track number
DOLBY NR |
OFF |
ALL DISC S
Elapsed time
continued
Operations Basic
11
Playing a CD (continued)
To |
Do this |
Stop playback |
Press p. |
|
|
Pause |
Press P. Press again to resume |
|
playback. |
|
|
Select a track |
During playback or pause, turn |
|
the jog dial clockwise (to go |
|
forward) or counterclockwise (to |
|
go backward) and release it when |
you reach the desired track. Or press AMS* + (to go forward) or AMS* = (to go backward) on the remote.
Find a point in Press and hold ) or 0 during a track playback, and release at the
desired point.
Select a CD |
Press one of the DIRECT PLAY |
|
buttons (or DISC SKIP). |
Play only the |
Press 1/ALL DISCS repeatedly |
CD you have |
until “1 DISC” appears. |
selected |
|
Play all CDs |
Press 1/ALL DISCS repeatedly |
|
until “ALL DISCS” appears. |
Remove or |
Press 6OPEN. |
change the |
|
CDs |
|
|
|
Adjust the |
Turn VOLUME (or press |
volume |
VOLUME +/– on the remote). |
|
|
* AMS: Automatic Music Sensor.
Tips
•Pressing · while the system power is off automatically turns on the system and starts CD playback if there is a CD on the tray (One Touch Play).
•You can switch from another source to the CD player and start playing a CD just by pressing · or one of the DIRECT PLAY buttons (Automatic Source Selection).
•If there is no CD in the player, “NO DISC” appears in the display.
•You can change the CD in the loading position during playback.
12
Recording a CD
— CD Synchro Recording
This function lets you record from a CD to a tape easily. You can use TYPE I (normal) or TYPE II (CrO2) tapes. The recording level is adjusted automatically.
1/u
(Power) SURROUND 7 p ª 5
6 DOLBY NR 3 |
2 4 |
p |
1 |
|
1 Press 6EJECT and insert a blank |
||||
tape into deck B. |
|
|
|
|
|
With the side you want to |
|||
|
record on facing forward |
|||
ª |
ª |
ª |
ª |
|
2 Press 6OPEN and place a CD. |
|
|||
With the label |
|
|
|
|
side up. |
ª ª |
|
ª |
ª |
When you play |
|
|
|
|
a CD single, |
|
ª |
|
|
place it on the |
|
|
|
inner circle of the tray.
3 Close the front cover.
4 Press DISC SKIP repeatedly until the disc number you want to record appears in the playing position indicator.
5 Press CD SYNC.
Deck B stands by for recording and the CD player stands by for playback, and the indicator on the · button (for the front side) lights up green.
6 Press DIRECTION repeatedly to select Ato record on one side or ß(or RELAY) to record on both sides.
7 Press P on deck B.
Recording starts.
To stop recording
Press pon deck B or on the CD player.
Tips
•If you want to record on the reverse side, press ª so the indicator on the ªbutton (for the reverse side) lights up green.
•When you record on both sides, be sure to start from the front side. If you start from the reverse side, recording stops at the end of the reverse side.
•When you want to reduce the hiss noise in lowlevel high-frequency signals, press DOLBY NR before step 7 so “DOLBY NR B” appears in the display.
•To record with the surround effect, press SURROUND so “SUR ” appears in the display.
The equalizer settings will not be recorded.
Note
You cannot listen to other sources while recording.
Operations Basic
13
Listening to the radio
— Preset Tuning
Before using this function, preset radio stations in the tuner’s memory (see “Step 3: Presetting radio stations”).
1/u |
STEREO/MONO |
3 2 1 |
|
||
(Power) VOLUME |
PRESET +/–
TUNER/BAND
VOLUME +/–
2 Press TUNING MODE repeatedly until “PRESET” appears in the display.
MANUAL nAUTO nPRESET
n
3 Press TUNING +/– (or PRESET +/– on the remote) to tune in the desired preset station.
LBT-D390/D790/G5500/XB33/XB33K/XB44/ XB44K/XB50/XB60
Preset number
DOLBY NR
OFF
TUNED
STEREO
PRESET ALL DISC S
MHz
Frequency
LBT-XB66/XB66K/XB660
Preset number
|
|
|
|
|
|
|
|
DOLBY NR |
|
|
|
||
|
OFF |
|
|
PRESET |
||
|
|
|
|
|
||
|
|
|
|
|
TUNED |
|
|
|
|
|
|
STEREO |
|
ALL DISC S |
|
|
|
|
MHz |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Frequency
To |
Do this |
Turn off the radio |
Press 1/u. |
Adjust the volume |
Turn VOLUME (or press |
|
VOLUME +/– on the |
|
remote). |
1 Press TUNER/BAND repeatedly until the band you want appears in the display.
Each time you press this button, the band changes as follows:
2 band model: FM ˜AM
3 band model:
FM nMW nLW n
4 band model:
FM nMW nLW nUKV* n
* When you select this band, “STEREO Plus” appears in the display.
To listen to non-preset radio stations
Press TUNING MODE repeatedly in step 2 until “MANUAL” appears, then press TUNING +/– to tune in the desired station.
Tips
•Pressing TUNER/BAND while the system power is off automatically turns on the system and tunes to the last received station (One Touch Play).
•You can switch from another source to the radio just by pressing TUNER/BAND (Automatic Source Selection).
•If an FM program is noisy, press STEREO/ MONO so “MONO” appears in the display. There will be no stereo effect, but the reception will improve. Press this button again to restore the stereo effect.
•To improve broadcast reception, move the supplied antennas.
14
Recording from the radio
You can record a radio program on a tape by tuning in a preset station. You can use TYPE I (normal) or TYPE II (CrO2) tapes. The recording level is automatically adjusted.
1/u
(Power) SURROUND 3 2 1
6 DOLBY NR ª p 7 4 5
1 Press TUNER/BAND repeatedly until the band you want appears in the display.
2 Press TUNING MODE repeatedly until “PRESET” appears in the display.
3 Press TUNING +/– to tune in a preset station.
LBT-D390/D790/G5500/XB33/XB33K/XB44/ XB44K/XB50/XB60
Preset number
DOLBY NR
OFF
TUNED
STEREO
PRESET
ALL DISC S
MHz
Frequency
LBT-XB66/XB66K/XB660
Preset number
DOLBY NR
OFF
PRESET
TUNED
STEREO
ALL DISC S |
MHz |
Frequency
4 Press 6EJECT and insert a blank tape into deck B.
With the side you want to record on facing forward
ª |
ª |
ª |
ª |
5 Press rREC.
Deck B stands by for recording, and the indicator on the ·button (for the front side) lights up green.
6 Press DIRECTION repeatedly to select Ato record on one side or ß(or RELAY) to record on both sides.
7 Press P on deck B.
Recording starts.
To stop recording
Press pon deck B.
continued
Operations Basic
15