DME PROCESSOR PACK
MVE-9000-C
MULTI FORMAT DME PROCESSOR
MVE-9000
HK-PSU04
MKE-9020M
MKE-9021M
MKE-9040M
INSTALLATION MANUAL 1st Edition
!WARNING
This manual is intended for qualified service personnel only.
To reduce the risk of electric shock, fire or injury, do not perform any servicing other than that contained in the operating instructions unless you are qualified to do so. Refer all servicing to qualified service personnel.
!WARNUNG
Die Anleitung ist nur für qualifiziertes Fachpersonal bestimmt.
Alle Wartungsarbeiten dürfen nur von qualifiziertem Fachpersonal ausgeführt werden. Um die Gefahr eines elektrischen Schlages, Feuergefahr und Verletzungen zu vermeiden, sind bei Wartungsarbeiten strikt die Angaben in der Anleitung zu befolgen. Andere als die angegeben Wartungsarbeiten dürfen nur von Personen ausgeführt werden, die eine spezielle Befähigung dazu besitzen.
!AVERTISSEMENT
Ce manual est destiné uniquement aux personnes compétentes en charge de l'entretien. Afin de réduire les risques de décharge électrique, d'incendie ou de blessure n'effectuer que les réparations indiquées dans le mode d'emploi à moins d'être qualifié pour en effectuer d'autres. Pour toute réparation faire appel à une personne compétente uniquement.
MVE-9000 |
Serial No. 10001 and Higher |
HK-PSU04 |
Serial No. 10001 and Higher |
MKE-9020M |
Serial No. 10001 and Higher |
MKE-9021M |
Serial No. 10001 and Higher |
MKE-9040M |
Serial No. 10001 and Higher |
MVE-9000 IM
For MVE-9000
Attention-when the product is installed in Rack:
1.Prevention against overloading of branch circuit
When this product is installed in a rack and is supplied power from an outlet on the rack, please make sure that the rack does not overload the supply circuit.
2.Providing protective earth
When this product is installed in a rack and is supplied power from an outlet on the rack, please confirm that the outlet is provided with a suitable protective earth connection.
3.Internal air ambient temperature of the rack
When this product is installed in a rack, please make sure that the internal air ambient temperature of the rack is within the specified limit of this product.
4.Prevention against achieving hazardous condition due to uneven mechanical loading
When this product is installed in a rack, please make sure that the rack does not achieve hazardous condition due to uneven mechanical loading.
5.Install the equipment while taking the operating temperature of the equipment into consideration
For the operating temperature of the equipment, refer to the specifications of the Operation Manual.
6.When performing the installation, keep the rear of the unit 10 cm (4 inches) or more away from walls in order to obtain proper exhaust and radiation of heat.
For MVE-9000
When using a LAN cable:
For safety,do not connect to the connector for peripheral device wiring that might have excessive voltage.
MVE-9000 IM |
1 (P) |
|
|
Table of Contents |
|
Manual Structure |
|
||
Purpose of this manual .............................................................................................. |
2 |
||
Related manuals |
......................................................................................................... |
2 |
|
Contents ..................................................................................................................... |
|
2 |
|
Trademark .................................................................................................................. |
|
2 |
|
1. |
Installation |
|
|
1-1. |
Operating ...............................................................................Environment |
1-1 |
|
1-2. |
Power Supply .............................................................................................. |
1-1 |
|
|
1-2-1. .................................................................. |
Power Specifications |
1-1 |
|
1-2-2. ........................................................ |
Recommended Power Cord |
1-2 |
1-3. Installation ....................................................Space (External dimensions) |
1-3 |
||
1-4. |
Installing ..................................................................................the Options |
1-4 |
|
|
1-4-1. ......................................................Installing the Plug-in Boards |
1-4 |
|
|
1-4-2. ..................................................Installing the Connector Board |
1-6 |
|
|
1-4-3. ........................................................... |
Installing the HK - PSU04 |
1-7 |
1-5. |
Rack Mounting ............................................................................................ |
1-8 |
|
1-6. Matching ..............................................................Connectors and Cables |
1-10 |
||
1-7. Input/Output ..........................................................Signals of Connectors |
1-11 |
||
1-8. Checks on .......................................................Completion of Installation |
1-12 |
||
|
1-8-1. ......................On-board Switches Setting and LED Functions |
1-12 |
|
1-9. |
System Connection.................................................................................... |
1-22 |
|
2. |
Service Overview |
|
|
2-1. |
Troubleshooting .......................................................................................... |
2-1 |
|
2-2. Periodic Inspection .........................................................and Maintenance |
2-2 |
||
|
2-2-1. .....................................................................................Cleaning |
2-2 |
|
2-3. About the ...............................................................Data Backup Capacitor |
2-2 |
MVE-9000 IM |
1 |
This manual is the installation manual of DME Processor Pack MVE-9000-C and their optional boards and units.
This manual is intended for use by trained system and service engineers, and describes the information on installing the MVE-9000-C system.
The following manuals are prepared for MVE-9000-C and their optional boards and units.
.Operation Manual (Supplied with MVE-9000-C)
This manual describes the application and operation of MVE-9000-C system.
.Maintenance Manual (Available on request)
This manual describes the detailed service information.
If this manual is required, please contact your local Sony Sales Office/Service Center.
This manual is organized by following sections.
Section 1 Installation
This section describes the operating environment, power supply, installation space, installation of optional boards and units, rack mounting, connectors, input and output signals of connectors, checking upon completion of installation, and system configuration.
Section 2 Service Overview
This section describes the troubleshooting and periodic inspection and maintenance.
Registered trademark used in this manual is follows.
.Ethernet is a registered trademark of Xerox Corporation.
2 |
MVE-9000 IM |
Section 1
Operating guaranteed temperature : +5 dC to +40 dC Performance guaranteed temperature : +10 dC to +35 dC
Operating humidity : |
10 % to 90 % |
(relative humidity) |
|
Storage temperature : |
_20 dC to +60 dC |
Mass (when all options are installed) : Approx. 27 kg
Prohibited locations for installation
.Areas where the unit will be exposed do direct sunlight or any other strong lights.
.Dusty areas
.Areas subject to vibration.
.Areas with strong electric or magnetic fields.
.Areas near heat sources.
.Areas subject to electrical noise.
.Areas subject where is subjected to static electricity.
Ventilation
The inside of the MVE-9000-C is cooled by a fan (both sides).
The power supply can be damaged if the exhaust vent (both sides) and air intake (front panel) are blocked or the fan is stopped.
Therefore, leave a blank space of more than 10 cm in the front and both sides of the MVE-9000-C.
A switching regulator is used for the power supply of this unit. The voltage within the range of 100 V to 240 V can be used without changing the supply voltage.
Power requirements : |
AC 100 to 240 V ± 10 % |
Power frequency : |
50/60 Hz |
Current consumption (when all options are installed) : 6.0 to 2.5 A
m
.As the inrush current at turn-on is a maximum 110 A (at 100 V)/220 A (at 240 V), the capacity of the AC power source must be commensurate with this load.
If the capacity of the AC power is not adequately large,
the AC power source braker will operate or the unit will abnormally operate.
.The MVE-9000 contains the single power supply unit as the standard configuration. A maximum of two power supply units may be installed. When starting up the MVE-9000, be sure to turn on the power of one or more power supply units.
MVE-9000 IM |
1-1 |
This unit does not come with a power cord.
To get a power cord, please contact your local Sony Sales Office/Service Center.
w
.Use the approved Power Cord (3-core mains lead)/ Appliance Connector/Plug with earthing-contacts that conforms to the safety regulations of each country if
applicable.
.Use the Power Cord (3-core mains lead)/Appliance Connector/Plug conforming to the proper ratings (Voltage, Ampere).
If you have questions on the use of the above Power Cord/ Appliance Connector/Plug, please contact your local Sony Sales Office/Service Center.
w
.Never use an injured power cord.
.Plugging the power cord in the AC inlet, push as far as it will go.
For customers in the U.S.A. and Canada
1Power cord, 125 V 10 A (2.4 m) : !1-557-377-11
1 AC inlet
For customers in the all European countries
1 Power cord, 250 V 10 A (2.4 m) : !1-782-929-21
1 |
AC inlet |
|
1-2 |
MVE-9000 IM |
|
|
520 |
|
|
|
|
7 |
|
|
|
|
|
|
35 |
|
|
|
482 |
|
|
|
|
|
465 |
37.2 |
|
|
|
|
440 |
|
|
|
|
|
|
101.6 |
176(4U) |
161 |
|
|
375 |
|
17.5 |
|
|
|
|
|
144.5 |
115.5 |
115.5 |
|
|
|
|
|||
|
|
|
61 |
380 |
|
|
|
|
|
|
Unit : mm |
MVE-9000 IM |
1-3 |
The MVE-9000-C is shipped from the factory with the necessary option (refer to the following table) already installed in the MVE-9000, in accordance with the specified system configuration.
MVE-9000-C options
Model name |
|
Board configuration |
|
|
|
|
|
|
|
Plug-in board |
Connector board |
|
|
|
|
MKE-9020M |
_ |
CN-2357A board |
|
MVS Interface Board Set |
|
|
CN-2357B board |
|
|
|
|
MKE-9021M |
_ |
CN-2355A board |
|
Input/Output Board Set |
|
|
CN-2355B board |
|
|
|
|
MKE-9040M |
DVP-24A board |
|
|
Advanced Effects Board |
|
|
|
|
|
|
|
HK-PSU04 |
_ |
_ |
|
Power Supply Unit |
|
|
|
|
|
|
|
c
Be sure to turn off the POWER switch and unplug the power cord from the wall outlet before starting the installation work.
If the installation work is started with the POWER switch left on, it may cause electrical shock or damage of printed circuit boards.
Installation procedure
1.Turn off the main power of the MVE-9000 and disconnect the AC power cord from the wall outlet.
2.Loosen the four screws (with drop-safe) and remove the front panel in the direction of the arrow.
Screws |
(with drop-safe) |
Front panel |
Screws |
(with drop-safe) |
3.Remove the four screws (B3 x5), and remove the “plug-in board loose-proof assembly”.
B3 x5 |
Plug-in board |
loose-proof assembly |
B3 x5 |
1-4 |
MVE-9000 IM |
4.While the eject levers are kept open as shown in the illustration, insert the plug-in board into the board guide rails.
Eject levers |
Name of option |
Name of board |
Slot on the front side |
MKE-9040M |
DVP-24A board*1 |
3, 4, 5, 6 |
*1 : The DVP-24A boards are assigned to the following channels in accordance with the slots to which the boards are inserted.
Slot |
Channel |
3 |
CH1 |
|
|
4 |
CH2 |
|
|
5 |
CH3 |
|
|
6 |
CH4 |
|
|
5.While closing the eject levers in the direction of arrow 1, push in the plug-in board.
1 |
1 |
Eject lever |
Eject lever |
6.Attach the plug-in board loose-proof assembly and the front panel by reversing the installation steps 2, 3.
MVE-9000 IM |
1-5 |