SOLTEK SL-63AV User Manual

Page 1

his User‘s Guide & Technical Reference is for assisting system

manufacturers and end-users in setting up and installing the mainboard. Every effort has been made to ensure that the information in this manual is accurate. Soltek Computer Inc. is not responsible for printing or clerical errors. Information in this document is subject to change without notice and does not represent a commitment on the part of Soltek Computer Inc. No part of this manual may be reproduced, transmitted, translated into any language in any form or by any means, electronic or mechanical, including photocopying and recording, for any purpose without the express written permission of Soltek Computer Inc. Companies and products mentioned in this manual are for identification purpose only. Product names appearing in this manual may or may not be registered trademarks or copyrights of their respective companies.

oltek computer inc. Provides this manual “As is “ without war

ranty of any kind, either express or implied, including but not limited to the implied warranties or conditions of merchantability or fitness for a particular purpose. In no event shall Soltek computer inc. Be liable for any loss or profits, loss of business, loss of use or data, interruption of business, or for indirect, special, incidental, or consequential damages of any kind, even if Soltek computer inc. Has been advised of the possibility of such damages arising from any defect or error in this manual or product.

Model : SL-63AV

Edition : March 2000 Version : 2.0

http://www.soltek.com.tw

e-mail: support@soltek.com.tw

Page 2

63AV

CONTENT

MOTHERBOARD DIAGRAM.................................................... 5

JP3 / JP4: Bus Clock Select .................................................. 9

STANDARD CMOS SETUP.................................................... 12

BIOS FEATURES SETUP ...................................................... 14

CHIPSET FEATURES SETUP ............................................... 18

POWER MANAGEMENT SETUP........................................... 21

PnP/PCI CONFIGURATION SETUP ...................................... 25

LOAD SETUP DEFAULTS ..................................................... 28

CPU SPEED SETTING .......................................................... 29

INTEGRA TED PERIPHERALS............................................... 31

SUPERVISOR/USER PASSWORD........................................ 35

IDE HDD AUTO DETECTION ................................................ 36

SAVE & EXIT SETUP............................................................. 36

EXIT WITHOUT SA VING........................................................ 36

Appendix A

FLASH MEMORY UPDATE INSTALLATION ......................... 37

Appendix B

DRIVER INST ALLATION........................................................ 38

Page 3

63AV

Appendix C

THERMAL SENSOR CONNECTOR ...................................... 40

Page 4

63AV

SL-63AV

VIA APOLLO PRO133 SOCKET-370

F E A T U R E

PROCESSOR

Supports Intel PPGA Celeron 370 CPUs 300 ~ 533MHz or higher. Supports Intel FC-PGA Pentium III (Coppermine) CPUs 500E ~ 750 MHz or higher. Supports Cyrix Joshua CPUs. Supports 66/ 75*/ 83*/ 100/ 103*/ 105*/ 124*/ 133/ 140*/ 150*MHz system bus speeds. Clock multipliers up to 8x.

CHIPSET

VIA APOLLO PRO133 VT82C693A chipset (FSB supports 133MHz).

SYSTEM MEMORY

3x 3.3V DIMM sockets. 8MB to 768MB DRAM size.

SLOT

1x AGP slot supports 1x / 2x mode bus; 4x PCI Bus Master slots; 2x ISA slots.

ONBOARD I/O

2x Ultra ATA33/66 Bus Master IDE ports. 2x USB ports. 1x PS/2 mouse connector and 1x PS/2 keyboard connector. 1x 2.88MB Floppy port, 2x High Speed 16550A UART ports and 1x IrDA TX / RX Header.

POWER

AT / ATX power supply connector . Power-On by LAN(WOL), RTC Alarm, Modem Ring.

BIOS

2MB FLASH BIOS. Licensed AWARD BIOS, supports SCSI / ZIP / LS-120 / CDROM boot and ACPI Power Management.

FORM FACTOR / PCB

AT, 4 layers PCB, 22.0cm x 24.0cm size.

Page 5

M O T H E R B O A R D D I A G R A M

FLASH BIOS

JWOL1

USB

1 2

COM1

Winbond

W83977AF /F

COM2

MS1

LPT1

KB1

ATX POWER

63AV

AT POWER

PFAN1

SPK RESET KEYLOCK SUSLED

ISA2

HDD/LED

IR PWR SUSPEND

JP20

PCI 4

PCI 3

15 16

JVGA1

PCI 2

SFAN1

3 1

JP11

JP12

PCI 1

AGP

JP13

1 3

JP14

1 3 1 3

JP15

ISA1

VIA

596B

JBAT1

1 3

JP16

1 3

Cyrix

Intel

JP18/JP19/JP20

1-2 SHORT

2-3 SHORT

VIA

693A

IDE 1

Battery

IDE 2

DIMM 1 DIMM 2 DIMM 3

Default setting: Intel Celeron 300A/66MHz.

FDD1

1 3

JP18

CFAN1

JP19

SOCKET 370

Clock Generator

JP3

1 3 1 3

JP4

NOTE: For 100/133MHz CPU environment, the SDRAM sepc must comply with PC-

100/PC-133 spec.

Page 6

63AV

CPU Type Configuration

CPU MODEL BUS RATIO BUS CLOCK

Pentium III 533EB/133

(133MHz * 4.0x)

Celeron 300/66

(66MHz * 4.5x)

Pentium III 600EB/133

(133MHz * 4.5x)

Celeron 333/66

(66MHz * 5.0x)

Pentium III 500E/100

(100MHz * 5.0x)

Pentium III 667B/133

(133MHz * 5.0x)

Celeron 366/66

(66MHz * 5.5x)

Pentium III 550E/100

(100MHz * 5.5x)

Pentium III 733B/133

(133MHz * 5.5x)

Celeron 400/66

(66MHz * 6.0x)

Pentium III 600E/100

(100MHz * 6.0x)

Celeron 433/66

(66MHz * 6.5x)

Pentium III 650/100

(100MHz * 6.5x)

Celeron 466/66

(66MHz * 7.0x)

Pentium III 700/100

(100MHz * 7.0x)

Celeron 500/66

(66MHz * 7.5x)

Pentium III 750/100

(100MHz * 7.5x)

Celeron 533/66

(66MHz * 8.0x)

NOTE 1: Use jumper(hardware) settings > set JP13/JP14 JP15/JP16 manually. NOTE 2: Use jumperless settings > JP13/JP14/JP15/JP16 must set to DEFAULT, that means all JP13/JP14/ JP15/JP16 are 1 & 2 short. NOTE 3: (#) Pentium III Coppermin FC-PGA CPUs.

C P U C L O C K S E T T I N G

JP13 JP14 JP15 JP16

1 3 1 3 1 3 1 3

JP3

JP4

JP3

JP4

JP3

JP4

JP3

JP4

JP3

JP4

JP3

JP4

JP3

JP4

JP3

JP4

JP3

JP4

1 3

Page 7

Bus Ratio Select

BUS RATIO

2.0x

3.0x

4.0x

5.0x

6.0x

7.0x

8.0x

JP13~JP16

JP13

1 3 1 3

JP14

1 3

JP15

1 3

JP16

JP13

1 3 1 3

JP14

1 3

JP15

1 3

JP16

JP13

1 3 1 3

JP14

1 3

JP15

1 3

JP16

JP13

1 3 1 3

JP14

1 3

JP15

1 3

JP16

JP13

1 3 1 3

JP14

1 3

JP15

1 3

JP16

JP13

1 3 1 3

JP14

1 3

JP15

1 3

JP16

JP13

1 3 1 3

JP14

1 3

JP15

1 3

JP16

BUS RATIO

2.5x

3.5x

4.5x

5.5x

6.5x

7.5x

By BIOS

(jumperless

setting)

(DEFAULT)

JP13~JP16

JP13

1 3 1 3

JP14

1 3

JP15

1 3

JP16

JP13

1 3 1 3

JP14

1 3

JP15

1 3

JP16

JP13

1 3 1 3

JP14

1 3

JP15

1 3

JP16

JP13

1 3 1 3

JP14

1 3

JP15

1 3

JP16

JP13

1 3 1 3

JP14

1 3

JP15

1 3

JP16

JP13

1 3 1 3

JP14

1 3

JP15

1 3

JP16

JP13

1 3 1 3

JP14

1 3

JP15

1 3

JP16

63AV

Page 8

63AV

J U M P E R S E T T I N G

A1 A2

A1: 1st HDD LED B. : INFRARED (IR) D. : SUSPEND CONNECTOR F. : RESET SWITCH H. : KEYLOCK

A2: 2nd HDD LED C. : POWER SWITCH E. : SPEAKER G. : POWER LED I. : SUSPEND LED

#FAN1: Onboard FAN (12V) Connector

#FAN1 FUNCTION CFAN1 CPU FAN SFAN1 CHASSIS FAN PFAN1 POWER FAN

JP3 / JP4: Bus Clock Select

Bus Clock JP3 / JP4

H I

100MHz

133MHz

Auto Select 66/100/133MHz

(default)

1 3

JP3 JP4

Page 9

JP11 / JP12: USB Port Select

USB Port JP11 / JP12

Redirect USB port1 to USB

connector (default)

Redirect USB port1 to AGP

port

JP18 / JP19 / JP20: Intel / Cyrix CPU Select

CPU TYPE

Intel CPU (Default)

Cyrix Joshua CPU

JP18

1 3

JP19

63AV

JP11

JP12

JP11

JP12

JP20

JVGA1: VGA Card

This jumper is set for the PCI VGA card only. Open this jumper when the system is not able to boot up. If you use AGP card, it is important to set default with JVGA1.

JVGA1

For PCI VGA card

Normal (default)

Page 10

63AV

JBAT1: Clear CMOS data

Clear the CMOS memory by shorting this jumper 2 & 3 momentarily, and then remove the cap back to 1 & 2 to retain original CMOS setting.

CMOS Status

JBAT1

Clear CMOS Data

Retain Data (default)

KB1: Keyboard Connector MS1: PS/2 mouse Connector USB: USB Connector JWOL1: Wake On LAN (WOL) Connector

This jumper is designed to use LAN to boot up the system. Connect the wake on signal from LAN card to this connector.

***For support WOL, the ATX power supply has to have at least 5V/720mA

standby current.***

NOTE: “VIA Patch Code”, “VIA AGP VxD Driver” & “VIA PCI IRQ Routing

Miniport” installation, please refer to Appendix B.

Page 11

63AV+ BIOS

This VIA82C693A chipset Apollo Pro-Plus comes with the AWARD BIOS from AWARD Software Inc. Enter the AWARD BIOS program Main Menu by:

1. Turn on or reboot the system. After a series of diagnostic checks, the following message will appear:

PRESS <DEL> TO ENTER SETUP

2. Press the <DEL> key and the main program screen will appear as follows:

3. Using the arrows on your keyboard, select an option, and press <Enter>.

Modify the system parameter to reflect the options installed in your system.

4. You may return to the Main Menu anytime be pressing <ESC>.

5. In the Main Menu, “SAVE AND EXIT SETUP” saves your changes and

reboots the system, and “EXIT WITHOUT SAVING” ignores your changes and exits the program.

ROM PCI / ISA BIOS (2A6LJSN9)

CMOS SETUP UTILITY

AWARD SOFTWARE, INC.

STANDARD CMOS SETUP

BIOS FEATURES SETUP

CHIPSET FEATURES SETUP

POWER MANAGEMENT SETUP

PNP/PCI CONFIGURATION

LOAD SETUP DEFAULTS

Esc : Quit F10 : Save & Exit Setup

CPU SPEED SETTING

INTEGRATED PERIPHERALS

SUPERVISOR PASSWORD

USER PASSWORD

IDE HDD AUTO DETECTION

SAVE & EXIT SETUP

EXIT WITHOUT SAVING

: Select Item (Shift) F2 : Change Color

Page 12

63AV+ BIOS

STANDARD CMOS SETUP

Standard CMOS Setup allows you to record some basic system hardware configuration and set the system clock and error handling. You only need to modify the configuration values of this option when you change your system hardware configuration or the configuration stored in the CMOS memory gets lost or damaged.

Run the Standard CMOS Setup as follows:

1. Choose “ST ANDARD CMOS SETUP” from the Main Menu and a screen

with a list of options will appear.

2. Use one of the arrow keys to move between options and modify the

selected options by using PgUp/PgDn/+/- keys.

ROM PCI/ISA BIOS (2A69KSNH)

STANDARD CMOS SETUP

AWARD SOFTWARE, INC.

Date (mm:dd:yy) : Tue, Oct 19 1999 Time (hh:mm:ss) : 15 : 6 : 26

HARD DISK TYPE SIZE CYLS HEAD PRECOMP LANDZ SECTOR MODE

Primary Master : Auto 0M 0 0 0 0 0 AUTO Primary Slave : Auto 0M 0 0 0 0 0 AUTO Secondary Master : Auto 0M 0 0 0 0 0 AUTO Secondary Slave : Auto 0M 0 0 0 0 0 AUTO

Drive A : 1.44, 3.5 in. Drive B : None

Video : EGA/VGA Halt On : All Errors

Esc : Quit F1 : Help

(Shift) F2 : Change Color

: Select Item

Base Memory : 640K

Extended Memory : 64512K

Other Memory : 384K

Total Memory : 65536K

PU/PD/+/- : Modify

Page 13

63AV+ BIOS

Date (mm:dd:yy) Time (hh:mm:ss)

Primary (Secondary)

Master / Slave

Drive A / B

Video

Halt On

Set the current date and time.

This field records the specification for all non-SCSI Hard Disk Drives installed in your system. Refer to the respective documentation on how to install the drives.

Set the field to the type(s) of Floppy Disk drive(s) installed in your system. The choice: 360KB, 5.25in.

1.2MB, 5.25in. 720KB, 3.5in.

1.44MB, 3.5in.

2.88MB, 3.5in.

Set the field to the type of video display card installed in your system. The choice: Monochrome, Color 40x25, EGA / VGA, (default) Color 80x25

Set this warning feature for the type of errors that will cause the system to halt. The choice: All Errors, (defaults) No Errors, All But Keyboard, All But Diskette, All But Disk / Key

3. Press <ESC> and follow the screen instructions to save or disregard

your setting.

Page 14

63AV+ BIOS

BIOS FEATURES SETUP

BIOS Features Setup allows you to improve your system performance or set up system features according to your preference.

Run the BIOS Features Setup as follows:

1. Choose “BIOS FEATURES SETUP” from the Main Menu and a screen

with a list of options will appear.

ROM PCI/ISA BIOS (2A6LJSN9)

BIOS FEATURES SETUP

AWARD SOFTWARE, INC.

Virus Warning : Disabled CPU Internal Cache : Enabled External Cache : Enabled CPU L2 Cache ECC Checking : Enabled

Quick Power On Self Test : Enabled Boot Sequence : A,C,SCSI Swap Floppy Drive : Disabled Boot Up Floppy Seek : Disabled Boot Up NumLock Status : On IDE HDD Block Mode : Enabled Gate A20 Option : Fast Memory Parity/ECC Check : Disabled Typematic Rate Setting : Disabled Typematic Rate (Chars/Sec) : 6 Typematic Delay (Msec) : 250 Security Option : Setup PCI/VGA Palette Snoop : Disabled OS Select For DRAM > 64MB : Non-OS2

Video BIOS Shadow : Enabled C8000-CBFFF Shadow : Disabled CC000-CFFFF Shadow : Disabled D0000-D3FFF Shadow : Disabled D4000-D7FFF Shadow : Disabled D8000-DBFFF Shadow : Disabled DC000-DFFFF Shadow : Disabled

ESC : Quit F1 : Help F5 : Old Value F7 : Load Setup Defaults

: Select Item PU/PD/+/- : Modify (Shift)F2 : Color

2. Use one of the arrow keys to move between options and modify the

selected options by using PgUp/PgDn/+/- keys. An explanation of the <F>keys follows:

<F1>: “Help” gives options available for each item. <Shift> + <F2>: Change BIOS screen color. <F5>: Get the previous values. These values are the values with the

user started in the current session. <F6>: Load all options with the BIOS default values. <F7>: Load all options with the Setup default values.

Page 15

63AV+ BIOS

Virus Warning

CPU Internal Cache

External Cache

CPU L2 Cache ECC

Checking

Quick Power On Self

Test

Enabled: Activates automatically when the system boots up

causing a warning message to appear if there is anything attempting to access the boot sector or Hard Disk partition table.

Disabled: No warning message will appear when there is

something attempting to access the boot sector or Hard Disk partition table.

Note: Many diagnostic (or boot manager) programs which

attempt to access the boot sector table can cause the above warning message. If you will be running such a program, we recommend that you disable the virus protection first.

Choose Enabled (default) or Disabled. This option allows user to enable or disable the CPU internal cache.

Choose Enabled (default) or Disabled. This option allows user to enable or disable the external cache memory.

Choose Enabled (default) or Disabled.

Choose Enabled (default) or Disabled. This option allows user to speed up the Power-On-Self-T est routine.

Boot Sequence

Swap Floppy Drive

Boot Up Floppy Seek

Default is “A , C, SCSI”. This option determines which drive to boot at first for an operating system.

This option swaps floppy driver assignments when it’s enabled. The choice: Enabled, Disabled (default).

Enabled (default): During POST, BIOS checks the track num-

ber for Floppy Disk drive to see whether it’s 40 or 80 tracks.

Disabled: During POST, BIOS will not check the track num-

ber for Floppy Disk drive.

Page 16

63AV+ BIOS

Boot Up NumLock

Status

IDE HDD Block Mode

Gate A20 Option

Memory Parity / ECC

Check

Typematic Rate Setting

Typematic Rate

(Char / Sec)

On (default): Activate the NumLock function at boot up. Off: Close the NumLock function at boot up.

Choose Enabled (default) or Disabled. If your Hard Disk size is larger than 540MB, choose Enabled, and if you are using the IDE HDD Auto Detection option, the BIOS will choose this option automatically.

Note: Some older model Hard Disk drives do not provide

this function.

Choose Normal or Fast (default): This option allows the RAM to access the memory above 1MB by using the fast gate A20 line.

Choose Enabled or Disabled.

Choose Enabled or Disabled (default): Enable this option to adjust the deystroke repeat rate.

Range between 6 (default) and 30 characters per second. This option controls the speed of repeating keystrokes.

Typematic Delay (Msec)

Security Option

PCI / VGA Palette

OS Select for DRAM >

64MB

Choose 250 (default), 500, 750 and 1000. This option sets the time interval for displaying the first and the second characters.

Choose System or Setup (default). This option prevents unauthorized system boot up or use of BIOS Setup.

Choose Enabled or Disabled (default). It determines whether or not the MPEG ISA cards can work with PCI / AGP.

Non-OS2 (default): For Non-OS/2 operating system. OS: For OS/2 operating system.

Page 17

63AV+ BIOS

Video BIOS Shadow

C8000-CBFFF to DC000-

DFFFF Shadow

Enabled (default): Map the VGA BIOS to system RAM. Disabled: Don’t map the VGA BIOS to system RAM.

These options are used to shadow other expansion card ROMs.

3. Press <ESC> and follow the screen instructions to save or disregard your setting.

Page 18

63AV+ BIOS

CHIPSET FEATURES SETUP

Chipset Features Setup changes the values of the chipset registers. These registers control the system options.

Run the Chipset Features Setup as follows:

1. Choose “CHIPSET FEATURES SETUP” from the Main Menu and a screen with a list of options will appear.

2. Use one of the arrow keys to move between options and modify the selected options by using PgUp/PgDn/+/- keys.

ROM PCI/ISA BIOS (2A6LJSN9)

CHIPSET FEATURES SETUP

AWARD SOFTWARE, INC.

Bank 0/1 DRAM Timing : SDRAM 10ns Bank 2/3 DRAM Timing : SDRAM 10ns Bank 4/5 DRAM Timing : SDRAM 10ns SDRAM Cycle Length : 3 DRAM Clock : Host CLK Memory Hole : Disabled Read Around Write : Enabled Concurrent PCI/Host : Disabled System BIOS Cacheable : Disabled Video RAM Cacheable : Disabled AGP Aperture Size : 64M AGP-2X Mode : Disabled OnChip USB : Enabled USB Keyboard Support : Disabled

ESC : Quit F1 : Help F5 : Old Value F7 : Load Setup Defaults

: Select Item PU/PD/+/- : Modify (Shift)F2 : Color

Page 19

63AV+ BIOS

Bank 0/1 2/3 4/5 DRAM

Timing

SDRAM Cycle Length

DRAM CLOCK

Memory Hole

Read Around Write

This item allows you to select the value in this field, depending on whether the board has paged DRAMs or EDO (extended data output) DRAMs. The choice: EDO 50ns, EDO 60ns, Slow, Medium, Fast, Turbo

Y ou can select CAS latency time in HCLKs of 2/2 or 3/3. The system board designer should have set the values in this field, depending on the DRAM installed. Do not change the values in this field unless you change specifications of the installed DRAM or the installed CPU.

The setting of this item must depend on the spec of PC100/ PC133. For example, if user chooses HCLK + 33M, that means not only the motherboard but also the SDRAM needs to comply with PC-133 spec. Choice: Host CLK(default), HCLK-33M or HCLK+33M.

Choose Enabled or Disabled (default). In order to improve performance, certain space in memory can be reserved for ISA cards. This memory must be mapped into the memory’s space below 16MB.

DRAM optimization feature: If a memory read is addressed to a location whose latest write is being held in a buffer before being written to memory, the read is satisfied through the buf fer contents, and the read is not sent to the DRAM. The choice: Enabled, Disabled

Concurrent PCI / Host

System BIOS

Cacheable

When disabled, CPU bus will be occupied during the entire PCI operation period. The choice: Enabled, Disabled

Choose Enabled or Disabled (default). When Enabled, the access to the system BIOS ROM addressed at F0000HFFFFFH is cached.

Page 20

63AV+ BIOS

Video RAM Cacheable

AGP Aperture Size (MB)

AGP-2X Mode

OnChip USB

USB Keyboard Support

Choose Enabled or Disabled (default). When enabled, the access to the VGA RAM addressed is cached.

Choose 4, 8, 16, 32, 64 (default), 128 or 256MB. Memory map and graphics data structures can reside in a Graphics Aperture. This area is like a linear buffer. BIOS will automatically report the starting address of this buffer to the O.S.

This item allows user to enable / disable the AGP-2x (133MHz clock) mode.

This should be enabled if your system has a USB installed on the system board and you wish to use it. Even when so equipped, if you add a higher performance controller, you will need to disable this feature. The choice: Enabled, Disabled

Enabled: Enables function when the USB keyboard is being

used.

Disabled (default): When the AT keboard is being used.

3. Press <ESC> and follow the screen instructions to save or disregard your setting.

Page 21

63AV+ BIOS

POWER MANAGEMENT SETUP

Power Management Setup changes the system power savings function.

Run the Power Management Setup as follows:

1. Choose “POWER MANAGEMENT SETUP” from the Main Menu and a screen with a list of options will appear.

2. Use one of the arrow keys to move between options and modify the selected options by using PgUp/PgDn/+/- keys.

ROM PCI/ISA BIOS (2A6LJSN9)

POWER MANAGEMENT SETUP

AWARD SOFTWARE, INC.

ACPI function : Disabled Power Management : User Define PM Control by APM : Yes Video Off After : Suspend Video Off Method : V/H SYNC+Blank MODEM Use IRQ : 3 Soft-Off by PWRBTN : Instant-Off HDD Power Down : Disabled Doze Mode : Disabled Suspend Mode : Disabled ** PM Events ** VGA : OFF LPT & COM : LPT/COM HDD & FDD : ON DMA Master : OFF Modem Ring Resume : Disabled Wake Up On LAN : Disabled RTC Alarm Resume : Disabled

Primary INTR : ON IRQ3 (COM 2) : Primary IRQ4 (COM 1) : Primary IRQ5 (LPT 2) : Primary IRQ6 (Floppy Disk) : Primary IRQ7 (LTP 1) : Primary IRQ8 (RTC Alarm) : Disabled IRQ9 (IRQ2 Redir) : Secondary IRQ10 (Reserved) : Secondary IRQ11 (Reserved) : Secondary IRQ12 (PS/2 Mouse) : Primary IRQ13 (Coprpcessor) : Primary IRQ14 (Hard Disk) : Primary IRQ15 (Reserved) : Disabled

ESC : Quit F1 : Help F5 : Old Value F7 : Load Setup Defaults

: Select Item PU/PD/+/- : Modify (Shift)F2 : Color

Page 22

63AV+ BIOS

ACPI Function

Power Management

PM Control By APM

Video Off After

Video Off Method

Modem Use IRQ

Soft-Off By PWR-BTTN

Enabled: Turn on ACPI function. Disabled (default): Turn off ACPI function.

Choose Max. Saving, User Define (default), Disabled, or Min. Saving.

Choose Y es (default) or No. You need to choose Yes when the operating system has the APM functions, otherwise choose No.

Choose NA, Suspend, Standby (default) or Doze.

Choose Blank, DPMS or V/H Sync+Blank (default). Y ou can choose either DPMS or V/H Sync+Blank when ther monitor has the Green function. Y ou need to choose Blank when the monitor has neither the Green function.

Assign the IRQ number to the modem which is being used so that the ring signal can wake up the system. The default setting is 3 (COM2).

Instant-Off (default): Turn of f the system power at once after

pushing the power button.

Delay 4 Sec: Turn off the system power 4 seconds after push-

ing the power button (to meet PC97/98 spec)

HDD Power Down

Doze Mode

Suspend Mode

Time is adjustable from 1 to 15 minutes. When the set time has elapsed, the BIOS sends a command to the HDD to power down which turns off the motor.

This mode sets the CPU speed down to 33MHz.

The option allows you to choose the mode for the different timer. The Suspend mode turns off the CPU and saves the energy of the system.

Page 23

63AV+ BIOS

VGA

LPT & COM

HDD & FDD

DMA / master

Modem Ring Resume

Wake On LAN Enabled: Wake on the system from the LAN card (LAN card

When On of VGA, any activity from one of the listed system peripheral devices or IRQs wakes up the system. Choice: On(default), Off.

When On of LPT&COM, any activity from one of the listed system peripheral devices or IRQs wakes up the system. Choice: LPT/COM(default), NONE, LPT or COM.

When On of HDD&FDD, any activity from one of the listed system peripheral devices wakes up the system. Choice: On(default), Off.

When On, any activity from one of the listed system peripheral devices wakes up the system. Choice: On, Off(default).

An input signal on the serial Ring Indicator (RI) Line (in other words, an incoming call on the modem) awakens the system from a soft off state.

must support wake on LAN function and the power supply must provide at least 5V/7750mA standby current)

Disabled(default): Disable Wake On LAN function.

RTC Alarm Rescume

Primary INTR

When Enabled, you can set the date and time at the which the RTC(Real Time Clock) alarm awakens the system from suspend mode. Choice: Disabled(default), Enabled.

When set to On, any event occurring at will awaken a system

which has been powered down.

On(default): The system can not enter the power saving mode

when I/O ports or IRQ# is activated.

Off: The system still can enter the power saving mode when

I/O ports or IRQ# is activated.

Page 24

63AV+ BIOS

The following is a list of IRQ’s(Interrupt ReQuests), which can be exempted much as the COM ports and LPT ports above can. When an I/O device wants to gain the attention of the operating system, it signals this by causing an IRQ to occur. When the operating system is ready to respond to the request, it interrupts itself and performs the service. When set On, activity will neither prevent the system from going into a power management mode nor awaken it.

IRQ3 (COM2) IRQ4 (COM1) IRQ5 (LPT2) IRQ6 (Floppy Disk) IRQ7 (LPT1) IRQ8 (RTC Alarm)

3. Press <ESC> and follow the screen instructions to save or disregard your setting.

Page 25

63AV+ BIOS

PnP/PCI CONFIGURA TION SETUP

PnP/PCI Configuration Setup defines PCI bus slots.

Run the PnP/PCI Configuration Setup as follows:

1. Choose “PnP/PCI CONFIGURATION SETUP” from the Main Menu and a screen with a list of options will appear.

2. Use one of the arrow keys to move between options and modify the selected options by using PgUp/PgDn/+/- keys.

ROM PCI/ISA BIOS (2A6LJSN9)

PNP/PCI CONFIGURATION

AWARD SOFTWARE, INC.

PNP OS Installed : No Resources Controlled By : Auto Reset Configuration Data : Disabled

CPU to PCI Write Buffer : Enabled PCI Dynamic Bursting : Enabled PCI Master 0 WS Write : Enabled PCI Delay Transaction : Enabled PCI#2 Access #1 Retry : Disabled AGP Master 1 WS Write : Disabled AGP Master 1 WS Read : Disabled

IRQ-x assigned to : PCI/ISA PnP DMA-x assigned to : PCI/ISA PnP Assign IRQ For USB : Enabled Assign IRQ For VGA : Enabled

ESC : Quit F1 : Help F5 : Old Value F7 : Load Setup Defaults

: Select Item PU/PD/+/- : Modify (Shift)F2 : Color

Page 26

63AV+ BIOS

Note: BIOS will automatically diable all PnP resources ex-

cept the boot device card when you select Yes on NonPnP O.S.

PNP OS Installed

Resources Controlled

Reset Configuration

Data

CPU to PCI Write Buffer

PCI Dynamic Bursting

PCI Master 0 WS Write

Y es: OS supportsss Plug and Play function. No (default): OS doesn’t support Plug and Play function.

Choose Manual (default) or Auto. The BIOS checks the IRQ/ DMA channel number on the ISA and PCI card manually if you choose Manual. And the IRQ/DMA channel number will be checked automatically if you choose Auto.

Choose Enabled or Disabled (default). Disable retains Enabled PnP configuration data in BIOS and resets the PnP configuration data in the BIOS.

Choose Enabled(default) or Disabled.

Choose Enabled(default) or Disabled .

PCI Delay Transaction

PCI #2 Access #1 Retry

AGP Master 1 WS Write

AGP Master 1 WS Read

Choose Enabled(default) or Disabled .

Choose Enabled or Disabled(default).

Choose Enabled(default) or Disabled.

Choose Enabled or Disabled(default).

Page 27

63AV+ BIOS

IRQ-x assigned to

DMA-x assigned to

Assign IRQ for USB

Assign IRQ for VGA

Legacy ISA: Manually assigns IRQ/DMA to device. PCI/ISA PnP: BIOS assigns IRQ/DMA to device

automatically.

Enabled (default): Add one IRQ to USB controller. Disabled: Remove IRQ from USB controller. The system will

have extra IRQ for other devices but the USB controller will still not be diabled (only IRQ was removed)

Enabled (default): Add one IRQ to VGA controller. Disabled: Remove IRQ from VGA controller. The system will

have extra IRQ for other devices but the VGA controller will still not be disabled (only IRQ will be removed)

3. Press <ESC> and follow the screen instructions to save or disregard your setting.

Page 28

63AV+ BIOS

LOAD SETUP DEFAULTS

Load Setup Defaults option loads the default system values to the system configuration fields. If the CMOS is corrupted the defaults are loaded automatically.

Choose this option and the following message will appear:

“Load Setup Defaults (Y/N)? N”

To use the Setup Defaults, change the prompt to “Y” and press <Enter>.

Page 29

63AV+ BIOS

CPU SPEED SETTING

CPU Speed Setting option allows user to adjust CPU’s settings and retain some informations inside computer when it is working.

Run the Integrated Peripherals as follows:

1. Choose “CPU SPEED SETTING” from the Main Menu and a screen with a list of options will appear.

2. Use one of the arrow keys to move between options and modify the selected options by using PgUp/PgDn/+/- keys.

ROM PCI/ISA BIOS (2A6LGSNI)

CPU SPEED SETUP

AWARD SOFTWARE, INC.

CPU RATIO : X3 Auto Detect DIMM/PCI Clk : Disabled Spread Spectrum : Disabled CPU Host Clock(CPU/PCI) : Default CPU Warning Temperature : Current System Temp. : Current CPU1 Temperature : Current CPU2 Temperature : Current CPUFAN1 Speed : Current CPUFAN2 Speed : Currnet CPUFAN3 Speed : IN0(V) : IN1(V) : IN2(V) : + 5 V : + 12 V : - 12 V :

- 5 V : ESC : Quit F1 : Help F5 : Old Value F7 : Load Setup Defaults

: Select Item PU/PD/+/- : Modify (Shift)F2 : Color

Page 30

63AV+ BIOS

CPU Ratio

Auto Detect DIMM/PCI

clk

Spread Spectrum

CPU Host Clock (CPU/

PCI)

Current System Temp.

Current CPU1/2

Temperature

Current CPUFAN1/2/3

Speed

Select the CPU Ratio. The choice: 3.0x (default), 3.5x, 4.0x, 4.5x, 5.0x, 5.5x, 6.0x,

6.5x, 7.0x, 7.5x, 8.0x.

Choose Disabled (default) or Enabled. The clock generator will turn off the DIMM clock if this slot is empty .

Choose Disabled (default) or Enabled. This function is designed to EMI test only.

Select the CPU Host Clock. The choice: default, 66/33MHz, 75/37MHz, 83/41MHz, 124/

31MHz, 133/33MHz, 140/35MHz, 150/37MHz.

Shows the temperature of the system.

Shows temperature of the CPU.

Shows current speed of the FAN. The fan must provide rotary pulse. (Normally these types of fan have a three-wire connector.)

Voltage

Shows power supply actual voltage value.

3. Press <ESC> and follow the screen instructions to save or disregard your setting.

Page 31

63AV+ BIOS

INTEGRA TED PERIPHERALS

Integrated Peripherals option changes the values of the chipset registers. These registers control system options in the computer.

Run the Integrated Peripherals as follows:

1. Choose “INTEGRATED PERIPHERALS” from the Main Menu and a screen with a list of options will appear.

2. Use one of the arrow keys to move between options and modify the selected options by using PgUp/PgDn/+/- keys.

ROM PCI/ISA BIOS (2A6LGSNI)

INTEGRATED PERPHERALS

AWARD SOFTWARE, INC.

OnChip IDE Channel0 : Enabled OnChip IDE Channel1 : Enabled IDE Prefetch Mode : Enabled Primary Master PIO : Auto Primary Slave PIO : Auto Secondary Master PIO : Auto Secondary Slave PIO : Auto Primary Master UDMA : Auto Primary Slave UDMA : Auto Secondary Master UDMA : Auto Secondary Slave UDMA : Auto Init Display First : PCI Slot KBC input clock : 8MHz Onboard FDC Controller : Enabled Onboard Serial Port 1 : 3F8/IRQ4 Onboard Serial Port 2 : 2F8/IRQ3 UART Mode Select : Standard UART2 Duplex Mode : Half RxD, TxD Active : Lo, Lo IR Transmission Delay : Disabled

Onboard Parallel Port : 378/IRQ7 Parallel Port Mode : ECP/EPP ECP Use DMA : 3 EPP Mode Select : EPP1.7

ESC : Quit F1 : Help F5 : Old Value F7 : Load Setup Defaults

: Select Item PU/PD/+/- : Modify (Shift)F2 : Color

Page 32

63AV+ BIOS

OnChip IDE Channel

0 / 1

IDE Prefetch Mode

Primary

Master/Slave PIO

Secondary

Master/Slave PIO

Primary Master/Slave

UDMA

Secondary Master/Slave

UDMA

Init Display First

KBC input clock

The chipset contains a PCI IDE interface with support from two IDE channels. Select Enabled to activate the first and/or the second IDE interface. Select Disabled to deactivate an interface, if you install a primary and/or second add-on IDE interface. The choice: Enabled(default), Disabled.

Choose Enable(default), Disabled.

Choose Auto (default) or Mode 0~4. The BIOS will detect the HDD mode type automatically when you choose Auto. Y ou need to set to a lower mode than Auto when your hard disk becomes unstable.

Enabled (default): Turn on the onboard IDE function. Disabled: Turn off the onboard IDE function.

This option allows you to decide to activate PCI Slot or AGP first. Choose PCI Slot(default), AGP.

Choose 6MHz, 8MHz(default), 12MHz or 16MHz. There might be a compatible problem when it is above 8MHz.

Onboard FDC

Onboard Serial Port1

Onboard Serial Port2

Controller

Choose Enabled (default) or Disabled. Choose Disabled when you use an ISA card with FDD function, or choose Enabled to use the onboard FDD connector.

Choose Auto (default), 3F8/IRQ4, 2F8/IRQ3, 3E8/IRQ4, 2E8/ IRQ3 or Disabled. Don’t set port 1 & 2 to the same value, except when setting at Disabled.

Choose Auto (default), 3F8/IRQ4, 2F8/IRQ3, 3E8/IRQ4, 2E8/ IRQ3 or Disabled.

Page 33

63AV+ BIOS

Note: This option will not be displayed unless the EPP/ECP

is selected.

Note: The above 2 options won’t work unless UART2 Mode

HPSIR/ASKIR is selected.

UART Mode Select

UART2 Duplex Mode

RxD, TxD Active

IR Transmission Delay

Onboard Paralle Port

Choose Standard (default), HPSIR or ASKIR.

Choose Half (default) or Full.

Choose Lo,Lo (default) / Lo,Hi / Hi,Hi / Hi,Lo.

Enabled: Enable delay when transferring data. Disabled (default): Disable delay when transferring data.

Choose the printer I/O address: 378H/IRQ7 (default), 3BCH/ IRQ7, 278H/IRQ5 or Disabled.

Parallel Port Mode

Choose Normal (default), ECP/EPP, SPP mode. The mode depends on the external device connected to this port.

ECP Mode Use DMA

Choose DMA3 (default) or DMA1. Most sound cards use DMA1. Check with your sound card configuration to make sure that there is no conflict with this function.

Page 34

63AV+ BIOS

Note: The above 2 options will not be displayed unless the

EPP/ECP is selected.

Parallel Port EPP Ty pe

Choose EPP1.7 (default) or EPP1.9. EPP1.9 supports hardware handshake. This setting is dependent upon your EPP device.

3. Press <ESC> and follow the screen instructions to save or disregard your setting.

Page 35

63AV+ BIOS

Note: If you forget or lose the password, the only way to

access the system is to clear the CMOS RAM by setting JBAT1. All setup information will be lost and back to default seting. You need to run the BIOS setup program and re-define all settings again.

SUPERVISOR/USER P ASSWORD

These two options allow you to set your system passwords. Normally, the supervisor has a higher ability to change the CMOS setup option than the user. The way to set up the passwords for both supervisor and user are as follows:

1. Choose “CHANGE PASSWORD” from the Main Menu and press <Enter>. The following message appears:

Enter Password:

2. The first time you run this option, enter your own password up to 8 characters and press <Enter>. The screen doesn’t display the entered characters.

3. After you entered the password, the following message appears prompting you to confirm the password:

Confirm Password:

4. Enter the same password “exactly” as you just typed again to confirm the password and press <Enter>.

5. Move the cursor to Save & Exit Setup to save the password.

6. If you need to delete the password you entered before, choose the Supervisor Password and press <Enter>. It will delete the password that you had before.

7. Move the cursor to Save & Exit Setup to save the option you did, otherwise the old password will still be there the next time you turn your machine on.

8. Press <ESC> to exit to the Main Menu.

Page 36

63AV+ BIOS

IDE HDD AUTO DETECTION

IDE HDD Auto Detection detects the parameters of an IDE Hard Disk drive and automatically enters them to the Standard CMOS Setup screen.

The screen will ask you to select a specific Hard Disk for Primary Master after you selected this option. If you accept a Hard Disk detected by the BIOS, you can enter “Y” to confirm and then press <Enter> to check next Hard Disk. This function allows you to check four Hard Disks and you may press the <ESC> after the <Enter> to skip this function and go back to the Main Menu.

SAVE & EXIT SETUP

Save & Exit Setup allows you to save all modifications you have specified into the CMOS memory. Highlight this option on the Main Menu and the following message appears:

SAVE to CMOS and EXIT (Y/N)? Y

Press <Enter> key to save the configuration changes.

EXIT WITHOUT SAVING

Exit Without Saving allows you to exit the Setup utility without saving the modifications that you have specified. Highlight this option on the Main Menu and following message appears:

Quit Without Saving (Y/N)? N

You may change the prompt to “Y” and press the <Enter> key to leave this option.

Page 37

Appendix A

APPENDIX A

FLASH MEMORY UPDATE INSTALLATION

1. Download BIOS files and flash utility from your board vendor. They are: awdflash.exe and .bin file.

2. Copy them to bootable diskette and boot from diskette.

3. The diskette cannot include memory manager e.g. emm386.exe,qemm and himem.sys, otherwise there will appear an error message “insufficient memory”.

4. Type “awdflash filename(XXXX.bin)”.

5. Next screen will ask you save current bios to file or not? Depend on your diskette capacity, choose Y or N for this option.

6. Then screen ask you programming the flash memory now? type Y for this option.

7. Programming finish,utility will ask you reboot system.

8. Reset system and press DEL key enter bios setup screen.

9. Select LOAD SETUP DEFAULTS, press ENTER, press Y, press F10, press Y

10. Finish update procedure.

Page 38

Appendix B

APPENDIX B DRIVER INSTALLATION

If you are using Windows 98 SE, you do not need to install the 4-in-1 driver as the IRQ Routing Driver and the ACPI Registry are already incorporated into the operating system. Users with Windows 98 SE may update the IDE Busmaster and AGP drivers by installing them individually.

PART 1:

1. Put the CD into your CD-ROM.

2. There appears a welcome window.

(If doesn’t, it means that your CD-ROM auto-run function does not enable, but you still can browser the CD via Windows Explorer and change the directory to where your CD-ROM directory is. Then run the autorun.exe)

3. Select “Install Driver”.

4. Select “Install VIA Chipsets Driver”.

5. Select “Install 4in1 Driver”.

6. Then the program will automatically setup all drivers your system needs.

7. Finally, the system will re-boot.

NOTE: AFTER INSTALLED “ 4in1 Driver”, USER DOESN’T NEED TO INSTALL ANY

OTHER PROGRAM IN PART 2.

PART 2:

CAUTION!! ALL THE VIA MAINBOARD MUST INSTALL FOLLOWING 3 DRIVERS!!!

VIA Patch Code Installation

Windows95/Windows98:

1. Go to the CD-ROM disk, we suggest the CD-ROM title is D:\.

2. Find and run D:\Patch\Via\patch9x\Setup\Setup.exe

3. Select “Install VIA Chipset Functions’ Registry”, then it will automatically install this program.

Note! This program should be installed before any other VIA’s drivers.

VIA AGP VxD Driver for Windows 9x Installation

Windows95/Windows98:

1. Go to the CD-ROM disk, we suggest the CD-ROM title is D:\.

2. Find and run D:\Driver\Via\Agp\Setup\Setup.exe

3. Select “Install VIA AGP VxD in turbo mode” or “Install VIA AGP VxD normal mode”, then it will automatically install this program.

Page 39

Appendix B

VIA PCI IRQ Routing Miniport for Windows 9x Installation

Windows95/Windows98:

1. Go to the CD-ROM disk, we suggest the CD-ROM title is D:\.

2. Find and run D:\Patch\Via\Virq9x\Setup.exe

Note: Before install Windows98, user must enable two functions for this miniport driver

in the BIOS menu, one is “OnChip USB” in the “Chipset Features Setup” and another is “Assign IRQ for USB” in the “PNP/PCI Configuration Setup”.

Page 40

Appendix C

APPENDIX C THERMAL SENSOR

Thermal Sensor Connector

a: Connect to RT2. b: Connect this thermal sensor to

particular device which generates lots of heat such as Hard Disk, VGA chip, etc. When connected, user could observe the temperature change from the BIOS program.

VIA Hardware Monitor Setup

1. Make sure that the CD is in the CD-ROM.

2. There will appear a welcome window, please use the mouse to choose “Install Driver” item.

(If not, that means user’s CD-ROM autorun function is disabled, but user

could still install the program via Windows Explorer. )

3. Choose “Install VIA Chipset Driver” item, then choose “Install VIA Hardware Monitor” item.

4. The setup program will install Hardware Monitor software automatically.

SOLTEK SL-63AV User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual

M O T H E R B O A R D D I A G R A M

C P U C L O C K S E T T I N G

J U M P E R S E T T I N G

STANDARD CMOS SETUP

BIOS FEATURES SETUP

CHIPSET FEATURES SETUP

POWER MANAGEMENT SETUP

PnP/PCI CONFIGURA TION SETUP

LOAD SETUP DEFAULTS

CPU SPEED SETTING

INTEGRA TED PERIPHERALS

SUPERVISOR/USER P ASSWORD

IDE HDD AUTO DETECTION

SAVE & EXIT SETUP

EXIT WITHOUT SAVING

APPENDIX B DRIVER INSTALLATION