SMC Networks Gateway TTTM5800X, Gateway TTTM2400X User Manual

Size:
6.67 Mb
Download

TT™5800X/TT™2400X

Gateway

User Manual

802.11a

802.11b/g

All Rights Reserved. Copyright 2006 Teletronics International, Inc.

2 Choke Cherry Road, Rockville, MD 20850 Tel: 301.309.8500 Fax: 301.309.8851

Table of Contents

Disclaimers ………………………….………….….…….……….….………........3 Introduction ……………………………………………………………………….4 Product Features ………………………………………………………………...5 Product Specifications ………………………………………………………….5 Installation ………………………………………………………………..………10 Configuring windows for IP Networking ……………………………………11 Web Configuration Interface …………………………………………………..15 Appendix A: Warranty Policy …………………………………………………..50 Appendix B: RMA Policy ………………………………………………………..51 Appendix C: Regulatory Information …………………………………………52 Appendix D: Contact Information ……………………………………………..54 Appendix E: WDS Explained ……………………………………….…………..55 Appendix F: Antenna Diversity …………………………………….…………..57 Appendix G: Troubleshooting ………………………………………………….58 Appendix H: Glossary ……………………………………………………………59

All Rights Reserved. Copyright 2006 Teletronics International, Inc.

2 Choke Cherry Road, Rockville, MD 20850 Tel: 301.309.8500 Fax: 301.309.8851

Disclaimers

No part of this documentation may be reproduced in any form or by any means or used to make any derivative work (such as translation, transformation, or adaptation) without written permission from the copyright owner.

All the other trademarks and registered trademarks are the property of their respective owners.

Statement of Conditions

We may make improvements or changes in the product described in this documentation at any time. The information regarding to the product in this manual are subject to change without notice.

We assumes no responsibility for errors contained herein or for direct, indirect, special, incidental, or consequential damages with the furnishing, performance, or use of this manual or equipment supplied with it, even if the suppliers have been advised of the possibility of such damages.

Electronic Emission Notices

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1)This device may not cause harmful interference.

(2)This device must accept any interference received, including interference that may cause undesired operation.

FCC INFORMATION

The Federal Communication Commission Radio Frequency Interference Statement includes the following paragraph:

The equipment has been tested and found to comply with the limits for a Class B Digital Device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment usage generates radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communication. However, there is no grantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

Consult the dealer or an experienced radio/TV technician for help.

The equipment is for home or office use.

IMPORTANT NOTE

FCC RF Radiation Exposure Statement: This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the antenna and your body and must not be co-locatedor operating in conjunction with any other antenna or transmitter.

Caution: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

All Rights Reserved. Copyright 2006 Teletronics International, Inc.

2 Choke Cherry Road, Rockville, MD 20850 Tel: 301.309.8500 Fax: 301.309.8851

Introduction

The TTª5800X gateway is TeletronicsÕs answer to the ever growing demand for higher bandwidth and security in a wireless network environment. It is based on a brand new redesigned platform that not only offers faster performance and capacity but also the support all current pre IEEE 802.11i wireless security standards. The TTª5800X is the IEEE 802.11a version of the platform that directly targets the need to those that requires the more secure, less crowded 5.8 GHz frequency spectrum.

TTª5800X Product Photos

TTª5800X PCB

IEEE 802.11a miniPCI Card

 

TTª5800X Enclosure (NEMA4 Box)

All Rights Reserved. Copyright 2006 Teletronics International, Inc.

2 Choke Cherry Road, Rockville, MD 20850 Tel: 301.309.8500 Fax: 301.309.8851

Product Features

Compact size for small enterprise or system integrate service market

Compliant with IEEE 802.11a specifications

Supports 64/128-bitWEP, WPA and IEEE802.1x

Supports Atheros Super A (up to 108Mbps)

Intelligent firmware upgrade via Web browser

Built-inWeb-basedutility for easy configuration from any Web browser

Support POE (IEEE 802.3af) function

Supports wireless bridging and MAC address filtering

Super bright LED indicating status and signal level (RSSI)

Provide 10/100M, auto sensing MDI/MDI-XEthernet port

EzManager Support

*Atheros Super G (Proprietary technology of Atheros Communication Inc.) would only work in situations where both ends of the communication link are using the Atheros radio chipset.

Product Specifications

Main Chips

CPU: Ubicom IP3023

Radio: Supports 802.11a Atheros AR5213+AR5112

Mechanical

Chassis Dimension (W x D x L): 161mm x 30mm x 119mm

Board Spec

Specification

Description

Network Standard

IEEE 802.11 a, IEEE 802.3, IEEE802.3x

 

 

Ethernet

10/100BaseT Ethernet, Auto MDI/MDI-X

 

 

Network Architecture

Infrastructure; Ad-Hoc;AP

 

 

MAC

CSMA/CA

 

 

Status Indicators

POWER, Wireless LAN, and Ethernet LAN

 

 

Push Button

Reset to Default Button

 

 

Radio Spec

IEEE 802.11a 5 GHz mini-PCIcard

Specification

Description

 

 

Chipset

MAC/BB Processor Atheros AR5213 RF Chip Atheros AR5112

 

 

Power Consumption

IEEE 802.11a TX: ~1000 mA RX: ~400 mA

 

 

Antenna Connector

N-typeFemale

 

 

All Rights Reserved. Copyright 2006 Teletronics International, Inc.

2 Choke Cherry Road, Rockville, MD 20850 Tel: 301.309.8500 Fax: 301.309.8851

 

16dBm (± 2dB) @ 54Mbps

Output Power

17dBm (± 2dB) @ 48Mbps

18dBm (± 2dB) @ 36Mbps

 

 

19dBm (± 2dB) @ 6 Mbps

 

 

 

IEEE 802.11a Sensitivity @ 10% Packet Error Rate

 

54Mbps: -70dBm

 

48Mbps: -71dBm

Receiver Sensitivity

36Mbps: -75dBm

24Mbps: -79dBm

 

 

18Mbps: -82dBm

 

12Mbps: -84dBm

 

9Mbps: -86dBm

 

6Mbps: -87dBm

 

 

 

IEEE 802.11a (OFDM)

Modulation

48/54 Mbps (QAM-64)

24/36 Mbps (QAM-16)

 

 

12/18 Mbps (QPSK)

 

6/9 Mbps (BPSK)

 

 

 

USA(FCC): 5.15GHz ~ 5.25GHz, 5.25GHz ~ 5.35GHz, 5.47

 

 

GHz ~ 5.725 GHz, 5.725 GHz ~ 5.825 GHz

Operating Frequency

Europe(ETSI): 5.15 GHz ~ 5.35 GHz, 5.47 GHz ~ 5.725

 

GHz

 

 

 

Japan(TELEC): 5.15 GHz ~ 5.25 GHz

 

 

 

IEEE 802.11b/g 2.4 GHz mini-PCIcard

 

Specification

 

Description

 

 

 

 

 

Chipset

 

MAC/BB Processor Atheros AR5213 RF Chip Atheros AR5112

 

 

 

 

 

Power Consumption

 

IEEE 802.11b TX: ~1500 mA RX: ~400 mA

 

 

IEEE 802.11g TX: ~1500 mA RX: ~400 mA

 

 

 

 

 

 

 

 

Antenna Connector

 

U.Fl R-SMT(Inside),N-typeFemale (Outside)

 

 

 

 

 

 

 

IEEE 802.11b:

 

 

 

22dBm (± 3dB) @ 1Mbps

 

 

 

22dBm (± 3dB) @ 2Mbps

 

 

 

22dBm (± 3dB) @ 5.5Mbps

 

 

 

22dBm (± 3dB) @ 11Mbps

 

Output Power

 

IEEE 802.11g:

 

 

 

 

 

 

21dBm (±3dB) @ 54Mbps

 

 

 

22dBm (±3dB) @ 48Mbps

 

 

 

22dBm (±3dB) @ 36Mbps

 

 

 

22dBm (±3dB) @ 6 Mbps

 

 

 

 

 

 

 

IEEE 802.11b

All Rights Reserved. Copyright 2006 Teletronics International, Inc.

2 Choke Cherry Road, Rockville, MD 20850 Tel: 301.309.8500 Fax: 301.309.8851

 

Sensitivity @ 8% Packet Error Rate

 

IEEE 802.11g

 

Sensitivity @10% Packet Error Rate

 

54Mbps:-72dBm

Receiver Sensitivity

48Mbps:-73dBm

 

36Mbps:-77dBm

 

24Mbps:-81dBm

 

18Mbps:-84dBm

 

12Mbps:-86dBm

 

9Mbps:-88dBm

 

6Mbps:-89dBm

 

11Mbps:-88dBm

 

5.5Mbps:-90dBm

 

2Mbps:-92dBm

 

1Mbps:-95dBm

 

11Mbps:-88dBm

 

5.5Mbps:-90dBm

 

2Mbps:-92dBm

 

1Mbps:-95dBm

 

 

 

IEEE 802.11b (DSSS)

 

5.5/11 Mbps (CCK)

 

2 Mbps (DQPSK)

 

1 Mbps (DBPSK)

 

IEEE 802.11g (OFDM/DSSS)

Modulation

 

 

 

48/54 Mbps (QAM-64)

 

24/36 Mbps (QAM-16)

 

12/18 Mbps (QPSK)

 

6/9 Mbps (BPSK)

 

5.5/11Mbps (CCK)

 

2Mbps (DQPSK)

 

1Mbps (DBPSK)

 

 

 

USA(FCC): 2.412GHz ~ 2.462 GHz (CH1 ~ CH11)

Operating Frequency

Europe(ETSI): 2.412 GHz ~ 2.472 GHz (CH1 ~ CH13)

Japan(TELEC) : 11b: 2.412 GHz ~ 2.484 GHz (CH1 ~ CH14)

 

 

 

11g: 2.412 GHz ~ 2.472 GHz (CH1 ~ CH13)

 

 

 

LED Definition

All Rights Reserved. Copyright 2006 Teletronics International, Inc.

2 Choke Cherry Road, Rockville, MD 20850 Tel: 301.309.8500 Fax: 301.309.8851

 

 

Item

Color

 

Status

Specification

 

 

 

 

 

 

 

 

 

PWR

Red

 

ON

Power on

 

 

 

 

 

 

 

Off

No power

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

** ON

Connected

 

RF

Yellow

 

OFF

Not connected

 

 

 

 

Blinking

Connected and transmitting

 

 

 

 

 

 

 

 

 

 

 

 

 

ON

Connected

 

 

 

 

 

 

 

 

 

LAN

Green

 

OFF

Not connected

 

 

 

 

 

Blinking

Connected and transmitting

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Received Signal Level

Red

 

** Blinking left to right

Not connected (Scanning for AP)

 

 

 

 

 

 

 

** ON

Connected, indicating RSSI

 

(5 LEDs)

 

 

 

 

 

 

 

 

 

 

 

 

 

* All ON

 

 

 

 

 

 

 

 

 

 

 

* AP mode.

 

 

 

 

 

 

** SU mode.

 

 

 

 

 

Software Specification

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Item

 

Specification

 

 

 

 

WAN Features

 

 

Static IP, DHCP Client, PPPoE Client

 

 

 

 

 

MAC Cloning

 

 

 

 

 

 

 

 

 

 

 

 

 

 

WAN Ping Inbound Filter

 

 

 

 

 

 

 

 

 

 

 

LAN Features

 

 

RIP Support

 

 

 

 

 

 

DNS Relay

 

 

 

 

 

 

 

 

 

 

 

 

 

 

DHCP Server including IP-MACReservation

 

 

 

 

 

 

 

 

 

 

 

 

 

 

SSID Hiding

 

 

 

 

 

 

 

WEP/WPA/WPA2 Enterprise

 

 

 

 

 

 

MAC Filtering

 

 

 

 

 

 

 

WDS

 

 

 

 

Wireless Features

 

802.11d

 

 

 

 

 

 

 

RTS/Fragmentation Threshold

 

 

 

 

 

 

Ack Timeout

 

 

 

 

 

 

 

Transmit Power

 

 

 

 

 

 

 

Auto Channel Select

 

 

 

 

 

 

 

NAT

 

 

 

 

Gateway Features

 

UPNP NAT Pass-through

 

 

 

 

 

 

Firewall/DMZ (Demilitarized Zone)

 

 

 

 

 

 

Quality of Service

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Syslog

 

 

 

 

 

 

 

PingWatchdog

 

 

 

 

Management Features

 

Firmware upgradeable

 

 

 

 

 

 

 

Configuration import/export

 

 

 

 

 

 

EZ-Manager

 

 

 

 

 

 

 

 

 

 

External AC Power Adapter

All Rights Reserved. Copyright 2006 Teletronics International, Inc.

2 Choke Cherry Road, Rockville, MD 20850 Tel: 301.309.8500 Fax: 301.309.8851

Item

Specification

Input Voltage

110-240VAC

 

 

Line Frequency

50/60Hz

 

 

Power Output to M/B

48VDC, 1A

 

 

Environmental

Item

Specification

Operating Temperature

-20C to 40 C(-4F to 104 F),

10 to 90% (non-condensing)

 

 

 

Storage Temperature

-25C to 70 C(-13F to 158 F),

10 to 90% (non-condensing)

 

 

 

Standards / Regulatory Compliance

CE, FCC

Product Kit Part Listing

1.TT™5800X 802.11a PCBA or TT™2400X 802.11b/g PCBA (1)

2.IEEE 802.11a o r IEEE 802.11b/g mini-PCIradio card (1)

3.Power over Ethernet Injector (1)

4.48VDC Power Adapter (1)

5.Ethernet Cable (2)

6.Waterproof RJ-45Connector (1)

7.Mounting Hardware (1)

8.User Manual

Note: If any item listed above is damaged or missing, please contact your dealer immediately.

System Requirements

Any desktop or laptop with an Ethernet interface

TCP/IP protocol suite installed

Standard CAT5 Ethernet cables with RJ45 connectors

Internet Explorer 5.0 or later / Firefox 1.0 or higher

Installation

All Rights Reserved. Copyright 2006 Teletronics International, Inc.

2 Choke Cherry Road, Rockville, MD 20850 Tel: 301.309.8500 Fax: 301.309.8851

Preparation for Installation

Always double check for any missing parts from the kit you received before deployment.

Next step is to set up the computer Ethernet interface for configuring the TT™5800X/TT™2400X. you’ll need to set the computer Ethernet interface within the same IP range as your TT™5800X/TT™2400X.

Check the following section - “Hardware Installation” and the next chapter - “Configuring Windows for IP Networking” to obtain complete details.

Hardware Installation

Follow the procedure below to install your TT™5800X/TT™2400X device:

1.Select a suitable place on the network to install the TT™5800X/TT™2400X. For best wireless reception and performance the external antenna should be positioned within Line of Sight from the AP with proper alignment.

2.Connect the TT™5800X/TT™2400X to the ODU side of the PoE Injector, via a straight Ethernet cable (Cat-5),and then connect the NET side of the PoE Injector to either a computer or an Ethernet Switch.Note: The TT™5800X/TT™2400X now fully supports the MDI/MDI-X standard and no longer requires the use of cross over cable to connect directly with a computer.

3.Connect the 48VDC power adapter to the power jack on the PoE injector to power on the TT™5800X/TT™2400X.

4.Check the LEDs on the TT™5800X/TT™2400X to confirm if the status is okay. At this point the Power LED should be on in Red and Ethernet should be on in Green. The RF light should light up once the unit is associated wirelessly with another wireless device. However at this point the unit is still in factory default setting so do not alarm if the RF light doesn’t light up.

5.Now the hardware installation is complete, and you may proceed to the next chapter –“ConfiguringWindows for IP Networking” for instruction on setting up network configurations.

Configuring Windows for IP Networking

All Rights Reserved. Copyright 2006 Teletronics International, Inc.

2 Choke Cherry Road, Rockville, MD 20850 Tel: 301.309.8500 Fax: 301.309.8851