Silvercrest 10-IN-1 User Manual [en, pl, de]

KOMPERNASS GMBH

Burgstraße 21

D-44867 Bochum

www.kompernass.com

Last Information Update · Stan informacji Stav informácií · Stand der Informationen:

12 / 2012 · Ident.-No.: SFB 10.1B2102012-3

IAN 86342

10-IN-1 REMOTE CONTROL SFB 10.1 B2

10-IN-1 REMOTE CONTROL

Operating instructions

PILOT UNIWERSALNY

Instrukcja obsługi

UNIVERZÁLNY DIAL'KOVÝ OVLÁDAČ

Návod na obsluhu

UNIVERSALFERNBEDIENUNG

Bedienungsanleitung

IAN 86342

Before reading, unfold the page containing the illustrations and familiarise yourself with all functions of the device.

Przed przeczytaniem proszę rozłożyć stronę z ilustracjami, a następnie proszę zapoznać się z wszystkimi funkcjami urządzenia.

Pred čítaním si odklopte stranu s obrázkami a potom sa oboznámte so všetkými funkciami prístroja.

Klappen Sie vor dem Lesen die Seite mit den Abbildungen aus und machen Sie sich anschließend mit allen Funktionen des Gerätes vertraut.

GB	Operating instructions	Page	1
PL	Instrukcja obsługi	Strona 29
SK	Návod na obsluhu	Strana 59
DE / AT / CH	Bedienungsanleitung	Seite	87

INDEX		PAGE
Important safety instructions		2
Device summary		3
Initial use		4
	Unpacking the device/checking the package contents 4
	Inserting the batteries	4
Operating components		5
	LCD display	5
	Buttons	6
The configuration menu		9
Menu language configuration		11
Code configuration (Programming the remote control) 11
	Programming by brand code search	11
	Programming by manual code input	12
	Programming by automatic code search	13
System configuration		14
	Setting the time	14
	Setting the date	14
	Adjust contrast	15
	Background Illumination	15
	Setting the global volume/mute switching	15
	Select a Tape-/Disc device for direct operation	16
	Setting the lock function	17
	System reset	17
Timer configuration		18
	Sleep timer	18
	Event timer	18
	Delete Timer	19
Learn configuration		19
	Code learn function	20
Macro configuration		21
Favourites channel		22
Volume control		24
	Vol +/—, (Mute switching)	24
For operation		24
	All OFF	24
Cleaning and storage		25
Faults / Remedies		25
Disposal		26
Technical data		26
Note regarding conformity		27
Importer		27
Warranty & Service		27
	- 1 -

10-IN-1 REMOTE CONTROL SFB 10.1 B2

Introduction

Congratulations on the purchase of your new appliance. You have clearly decided in favour of a quality product. These operating instructions are a part of this product. They contain important information in regard to safety, use and disposal. Before using the product, familiarise yourself with all of these operating and safety instructions. Use the product only as described and only for the specified areas of application. Retain these instructions for future reference. In addition, pass these documents on, together with the product, to any future owner.

Copyright

This documentation is copyright protected. All rights including those of photographic reproduction, duplication and distribution by means of particular methods (for example data processing, data carriers and data networks), wholly or partially as well as substantive and technical changes are reserved.

Important safety instructions

Proper use

Children may only operate the remote control under adult supervision.

The universal remote control can replace a maximum of ten remote controls. It can only be used for entertainment electronics with infrared receivers. The functions of the Universal remote control essentially correspond to those of the original remote control. The universal remote control is intended for private use. It is not suitable for commercial use.

Any other use is considered improper use. The manufacturer accepts no responsibility for damage caused by improper handling or unauthorized reconstruction.

Warning

A warning of this danger level signifies a possible dangerous situation. If the dangerous situation is not avoided it can lead to injuries. The directives in this warning are there to avoid personal injuries.

Important

A warning of this danger level signifies possible property damage. If the situation is not avoided it can lead to property damage. The directives in this warning are there to avoid property damage.

Note

A note signifies additional information that assists in the handling of the device.

- 2 -

Warning of injury danger as a result of

improper handling of batteries!

Batteries must be handled with special care. Take note of the following safety instructions:

•Keep batteries well away from children. Children can put batteries into their mouths and swallow them. If a battery is swallowed medical assistance must be sought IMMEDIATELY.

•Do not throw batteries into a fire. Never subject batteries to high temperatures.

•Explosion hazard! Non-rechargeable batteries must never be recharged.

•Do not open the batteries or short-circuit them.

•Battery acid leaking from a battery can cause inflammation of the skin. In event of contact with the skin, rinse with large amounts of water. If the liquid comes into contact with your eyes, rinse thoroughly with water, do not rub and immediately consult a doctor.

Attention!

The Universal remote control contains an infrared diode of laser class 1. In order to avoid eye injuries do not look at the diode with optical devices.

Damage to the device

•If the device is defective, do not attempt to repair it yourself. In case of damage, contact the manufacturer or the manufacturer's service hotline (see Warranty information).

•If liquid escapes from the device or if the device has been otherwise damaged, it must be inspected by the manufacturer or the manufacturer's service hotline. Contact the manufacturer or the manufacturer's service hotline (see Warranty information).

•Take the batteries out of the battery compartment as soon as they are depleted.

•If you will not be using the device for a long period of time, remove the batteries to prevent them from discharging.

•Always change all batteries at the same time and always use batteries of the same type.

Device summary

q LCD display

w /ALL OFF button e Device buttons r S button

t Arrow buttons y EXIT button u P +/— buttons i MACRO button

o Number buttons

a Button for one or two digit programme numbers

- 3 -

s Teletext function buttons d Illumination button

f Playback buttons g AV button

h Mute switching j VOL +/— buttons k MENU button l OK button

1( FAV / EPG button

2) Infrared sender/receiver 2! Battery compartment cover

Tips:

•The functions described here pertain to the theoretically ideal circumstance that the button structure of the respective original remote control is identical to this universal remote control. This only occurs, however, in rare cases. If, therefore, not all of the original remote control's functions can be reproduced it is not due to a dificiency in the Universal remote control.

•All the brand names used in these instructions or in the accompanying code list are trademarks of the corresponding companies.

Initial use

Unpacking the device/checking the package contents

Warning!

Keep the plastic packaging well away from small children. There is a risk of suffocation!

•Unpack the device and accessories.

•Check the package contents

-Universal remote control (URC),

-Operating instructions,

-Manufacturers directory with device code list:

-2 x 1,5 V Batteries, type AAA/LR03 (Micro)

Note: Transport damage

Ifyounoticeanytransportdamagecontactthemanufactureror themanufacturer'sService-Hotline(seewarrantyinformation).

Inserting the batteries

Attention!

The Universal remote control must only be operated with 1.5 Volt batteries (Type AAA, LR03).

Carry out the battery change as quickly as possible. Preset settings will remain saved for approx. 1 minute. If new batteries have not been installed within this time all of the settings will have to be carried out again. The time of day and date will, however, be lost in either case.

- 4 -

1.Open the battery compartment cover 2! in the direction of the arrow.

2.Insert the batteries as shown in the diagram and close the battery compartment.

The LCD display q is activated as long as batteries are installed. The following diagram shows the LCD display q after the batteries have been installed or changed.

Note:

If no LCD display q is visible check the polarity of the batteries or install new ones.

Operating components

LCD display

The LCD display q is divided into fields.

Text field 2@

Here is shown the currently selected device, for example DVD, TV VCR etc.

Infrared symbol 2#

Every time a button is pressed, with which an infrared signal is to be sent the Infrared symbol illuminates.

- 5 -

Code/Time field 2$

Here is shown the device code of the relevent selected device or the time of day. With the time of day indicator ":" the numbers blink in the middle. For time displays in the 12-hour format, the period of the day code is shown to the left of the time.

Day of the week field 2%

Here you can read the shortened form of the current day of the week after you have entered the date.

Standard display:

The standard readout of the LCD display q consists of the details for the relevent device, for example, "TV", the initial for the day of the week and the time of day indicator.

Buttons

Note:

All the functions described here can, of course, only be used if they are supported by the device being controlled.

/ALL OFF button. w

To switch the device on/off; press and hold for a few seconds to switch all devices on/off.

Device buttons e

The device buttons are used to select the device that should be operated.

Television

Video recorder

Accessory unit 1

Cable receiver

CD player

BluRay Disc Player

Audio amplifier

DVD player

Digital satellite receiver Accessory unit 2

The mentioned button allocation is not compulsory. You can, for example, also save the code for the video recorder on the TV slot.

"S" button r

Press and hold for 3 seconds to access the configuration menu or press briefly to show the date.

- 6 -

To access the target device’s electronic programme guide (EPG) first press briefly the S button r and then the FAV/EPG button 1(.

To control the “PIP” function (picture in picture) of your television set, first press the S button r followed by the - button of the Videotext function buttons s.

Arrow buttons t

Move up, right, left and down in menus.

EXIT button y

Move a level backward in the menu.

P +/— buttons u

Changing the reception channel.

In the DVD and CD-mode these buttons control the SKIP function

MACRO button i

MACRO button i followed by a number button o 1-6 activates a previously saved chain of commands.

Number buttons o

Enter programme and device code numbers.

Button for one/two digit programme numbers a

For two digit programme numbers (depending on the device type) first press

the a button then via the number buttons o enter the programme number.

When pressed again the display becomes single digit once more.

Teletext function buttons s

In teletext operation the buttons have the following functions:

Access the teletext function.

Stop automatic paging forward for

multi-page teletexts.

Enlarge page presentation

Screen text and TV image one upon the other

To end the teletext function.

- 7 -

To access the SWAP function of the target device briefly press the S button r, followed by the -button.

Note:

•The teletext function is only available in the European TV mode and your reception device must be teletext ready.

•In addition the P +/- buttons u control the following teletext functions:

P + Leaf one page forward

P — Leaf one page backwards

Playback buttons f

The playback buttons f control devices such as DVD/CD players and video recorders:

Start playback

Image format switching with TV operation.

Record

Stop Playback/Record/Wind

Pause playback

Rewind

Wind forward

The coloured marking of the playback buttons refer to the coloured fields in the video text, over which the Toptext functions can be controlled.

AV button g

Switch to the AV input.

Mute switching h

Switch sound on/off.

VOL+/— buttons j

Set volume (Volume).

MENU button k

Access the menu of the controlled device.

OK button l

You can confirm a menu selection with the OK button.

FAV/EPG button 1(

Press the FAV/EPG button to access your previously programmed favourite station.

To access the EPG function of the target device first press briefly the S button r.

- 8 -

The configuration menu

In the system settings you undertake the following:

•Programming the remote control to the devices to be controlled

•Settings for the menu language, time of day, date, display contrast, background illumination, volume, lock function as well as system reset.

•Timer settings

•The "learning" of designated button commands

•Setting up Macros

•Assigning favourites

On the following page you can see a summary of the menu structure.

- 9 -

- 10 -

Menu language configuration

For the device menu display you can select from 5 languages: English, German, Spanish, French and Italian.

1.Hold down the S button r for a little longer than 3 seconds. Carry out entries in the menu quickly because after approx. 15 seconds without an entry the menu will end.

2.“LANGUAGE SETUP” appears in the LCD display q. Press the OK button l.

3.“ENGLISH” now appears in the LCD display q. With thebuttons t select the desired language and confirm with the OK button l.

4.With the EXIT button y you exit the menu.

The device menu is now displayed in the selected language. For the following instructions we are assuming that you have selected your own language.

Code configuration

(Programming the remote control)

3 Programming methods are available for the remote control: Programming by brand code search, by automatic code search and by direct code input (manual).

First you should use the brand code search since this method is the fastest way of programming if the manufacturer of your device is itemized in the code list. As second is recommended the direct code input followed by the automatic code search.

Programming by brand code search

With this method you select the brand and code direct via the LCD display q.

Observe the following operational references to programme the remote control:

1.Press the device button e for the device that you want to programme the remote control.

2.Hold down the S button r for a little longer than 3 seconds. “LANGUAGE SETUP” appears in the LCD display q. With the or button t select “CODE SETUP” and confirm with the OK button l.

3."ENTER CODE" now appears in the LCD display q. With the buttons t select "BRAND CODE" and confirm with the OK button l.

4.Now appears the alphabetical first brand name from the list of pre-programmed devices.

5.With the 34 buttons t select the various brand names.

6.To make access easier you can skip directly to specific letters of the alphabet with the number buttons o:

2	=> A	3	=> D	4	=> G	5	=> J
6	=> M	7	=> P	8	=> T	9	=> W

Example for the search of a TV brand code: With button

- 11 -

number 5 the display skips to the letter "J". The first brand is "JEC"*. If, for example, you own a "Kenwood"* brand device, continue leafing with the 4 button t until this brand name appears. (* All brand names used here are trademarks of the corresponding manufacturer.)

7.The majority of manufacturers use several different codes for the remote control. You must now ascertain which of the available codes is best suited to your device. On the right underneath the brand name the relevent code will be shown in the LCD display q.

8.To test the code, point the remote control at the actual device and press the buttons that correspond to the functions of this device (except t, OK l, EXIT y, the device buttons e or the numeric buttons o).

9.If most of the buttons function press the OK button l to save the setting. In the LCD display q "OK" appears.

Subsequently the menu will close automatically.

10.If, however, none or only a few of the buttons function select with the 5 or 6 button t the next code and test again as described in step 8.

11.With the EXIT button y you move back one level in the

menu.

Repeat these operational steps for all devices that you would like to control with the remote control.

Programming by manual code input

In this mode the remote control can be programmed by direct input of a code number. You can obtain the necessary code number from the enclosed manufacturers directory with device code list. In the event that the new code is invalid the last valid programmed code will be restored.

1.Press the device button e for the device that you want to programme the remote control.

2.Hold down the S button r for a little longer than 3 seconds. “LANGUAGE SETUP” appears in the LCD display q. With the or button t select “CODE SETUP” and confirm with the OK button l.

3."ENTER CODE" now appears in the LCD display q. To access this function press the OK button l.

4.In the LCD display q appears the presently used code for the selected device. Now the first digit of the code blinks and waits for your code input. Enter the new four digit code via the number buttons o. After entering the fourth digit the whole code flashes. You can now test if the URC can control the device you want with this code. Press those keys that correspond to the functions of the device, with a TV set for example, PROG +/–. If the device reacts as required, confirm the code input with the OK button l. If it does not, enter the next possible code from the list and try again.

5.If the entered CODE is valid the code will be saved. In the LCD display q "OK" appears briefly. Subsequently

- 12 -

the menu will close automatically. In the event of failure the LCD display q shows briefly "ERROR" and waits for a new code entry. Then you repeat step 4.

6.With the EXIT button y you move back one level in the menu.

Programming by automatic code search

This process can take several minutes per device since all codes for the selected device have to be gone through. Therefore this method should only be used when the device cannot be programmed via brand code search or direct code input or if your device is not listed at all in the manufacturers directory with device code list.

Follow the steps listed below to carry out programming by means of the automatic code search.

1.Press the device button e for the device that is to be controlled (i.e. VCR).

2.Switch the device that is to be controlled with the remote control on. With VCR/DVD/CD devices please insert a tape and/or disc.

3.Hold down the S button r for a little longer than 3 seconds. “LANGUAGE SETUP” appears in the LCD display q. With the or button t select “CODE SETUP” and confirm with the OK button l.

4."ENTER CODE" now appears in the LCD display q. Press the or button t until "SEARCH CODE" is shown in the LCD display q. Point the remote control to the device and then press the OK button l to access the mode "automatic code search".

5.The search begins. Thereby the device sends, one after the other, the code numbers in ascending order. The infrared symbol 2# indicates this. Every search starts with the currently programmed code.

6.When the device reacts by switching off press immediately the OK button l to save the relevent code. The LCD display q shows briefly "OK".

7.Check to see if the majority of your device's functions can now be controlled with the remote contol. If yes you have most probably found the correct code. In the event that a few functions are not working you can start the automatic code search again beginning with step 1.

8.However if the device does not react any more you probably did not press the OK button l quick enough in step 6. Then press repeatedly the EXIT button y to exit the menu and return to the standard display.

9.Now hold down the device button e of the device for which you have just sought the relevent code. Below on the right in the LCD display q will thereby be shown the relevent code. Make a note of this number.

- 13 -

10.Then proceed as described in the preceding chapter "Programming by manual code entry" and check to see if the code with the next lowest number combination will function.

Tips:

1.While the code search is activated none of the buttons will function apart from OK l and EXIT y.

2.If the automatic search has reached the end of the code list it stops there. The display then returns to "SEARCH CODE".

System configuration

Setting the time

The LCD display q shows you the time of day. You set this as follows:

1.Hold down the S button r for a little longer than 3 seconds. The notice "LANGUAGE SETUP" appears. If appox. 15 seconds passes without an entry the device exits the menu and returns to the standard display.

2.With the or button t select "SYSTEM SETUP" and confirm with the OK button l.

3.In the LCD display q "TIME SETUP" appears. Confirm with the OK button l. The LCD display q now shows "TIME" and the time format (24 HR) blinks.

4.With the or button t you can switch to the other time format (12 HR). After which the time display for the time of day will show an “AM” or “PM” before the time.

„AM“ stands fpr “AM” = “ante meridium” (Morning, 0:00 o’clock midnight to 12:00 o’clock midday). „PM“ stands for “PM” = “post meridium” (Afternoon and evening, 12:00 o’clock midday to 0:00 o’clock midnight). Press the OK button l to confirm.

5.Now the hour indicator blinks. With the or button t select the hour number for the present time of day and press the OK button l.

6.Now the minute indicator blinks. With the or button t select the minute number for the present time of day and press the OK button l to save. The "TIME SETUP" notice appears again.

7.To exit this or the following menus press repeatedly the EXIT button y until the standard display appears in the LCD display q.

Setting the date

The LCD display q shows you the date when you press the S button r. You set the date in this way:

1.Hold down the S button r for a little longer than 3 seconds. The notice "LANGUAGE SETUP" appears.

2.With the or button t select "SYSTEM SETUP" and confirm with the OK button l.

- 14 -

3.In the LCD display q "TIME SETUP" appears. Press the button t to change to "DATE SETUP". Confirm with the OK button l.

4.In the display the year "2011" blinks. With the orbutton t you can change the year and confirm with the OK button l. With the or button t you can change the now blinking month and confirm with the OK button l. Now the day indicator blinks which you can also change with the or button t.

5.To save press the OK button l. The "DATE SETUP" notice appears again.

Adjust contrast

You can set the display's contrast as follows:

1.Hold down the S button r for a little longer than 3 seconds. The notice "LANGUAGE SETUP" appears.

2.With the or button t select "SYSTEM SETUP" and confirm with the OK button l.

3.With the or button t select "CONTRAST SETUP" and confirm with the OK button l.

4.In the LCD display q the contrast value now blinks which you can set with the or button t.

Display readout:

0 = highest contrast:

15 = lowest contrast

5.With the OK button l you can save the desired setting. The notice "CONTRAST SETUP" appears again.

Background Illumination

You can set how long the LCD display’s q background and the button illuminations remain alight after completion of the operation.. Thereby taking into account that the longer the illumination remains lit the shorter the battery life will be.

1.Hold down the S button r for a little longer than 3 seconds. The notice "LANGUAGE SETUP" appears.

2.With the or button t select "SYSTEM SETUP" and confirm with the OK button l.

3.With the or button t select "BACKLIT SETUP" and confirm with the OK button l.

4.In the LCD display q now blinks the second count for the length of time that the light is to be left on which you can set with the buttons t from 0 to 60. If you select "0" the background illumination will shut off completely.

5.With the OK button l you can save the desired setting. The notice "BACKLIT SETUP" appears again.

Setting the global volume/mute switching

So that you don’t always have to first press a device button for the volume control and mute switching, for these functions the URC always only responds to an individual device. You can determine this target device yourself.

- 15 -

1.Hold the S button r down for a little longer than

3 seconds. The notice „LANGUAGE SETUP“ appears.

2.With the or button t select “SYSTEM SETUP” and confirm with the OK button l.

3.With the or button t select “VOL/MUTE SETUP” and confirm with the OK button l.

4.The LCD display q shows “ALL VOL SET”. Press the OK button l, the display changes to „ALL VOL MODE“.

5.Now press the device button e for the device that is to be controlled by the global volume control.

6.If the specified device is equipped with a volume control, “SUCCESS” will be displayed briefly and the menu will close. From now on the volume control functions on the device just specified.

7.If this device is not equipped with its own volume control the URC will not allow this selection and shows “VOLUME ERROR”. Even then the menu will close. The volume control will then continue to function on the former device.

You can also deactivate the global volume control for specific devices.

1.For this select in the menu “VOL/MUTE SETUP” with theor button t the function “MODE VOL SET” and confirm with the OK button l. In the LCD display q appears „MODE VOL MODE”.

2.Now press the device button e for the device that is to be excluded from the global volume control. The LCD display q shows „SUCCESS“ and the global volume control is deactivated if the URC is working in the operational mode of one of the selected devices.

You can again override the settings in the “VOL/MUTE SETUP” menu.

1.For this select in the menu “VOL/MUTE CONF” with theor button t the function “VOL/MUTE RESET” and confirm with the OK button l.

2.The LCD display q prompts you, with CONFIRM RESET, to a confirmation which is done by pressing the OK button l. Press the OK button l if you want to delete the setting, the displayed “SUCCESS” then confirms the deletion of the device assignment to global volume control. Otherwise you press the EXIT button y to abort the deletion.

Select a Tape-/Disc device for direct operation

You can select a tape or disk device that you can control with the playback buttons f without first having to press the corresponding device button e.

1.Hold down the S button r for a little longer than 3 seconds. The notice “LANGUAGE SETUP” appears.

2.With the or button t select “SYSTEM SETUP” and confirm it with the OK button l.

- 16 -

3.In the LCD display q “TIME SETUP” appears. Press thebutton t to switch to “PLAYBACK SETUP”. Confirm with the OK button l.

4.With the or buttons t now select the device that should respond to the URC when you use the playback buttons f. Confirm with the OK button l.

5.If instead of a device you select “OFF” and confirm it with the OK button l, you switch the direct operation off. If you select “RESET” and confirm with the OK button l you activate the pre-programmed default settings (DVD) for this function.

6.The LCD display q shows “SUCCESS” and the selected device can now be directly controlled using the playback buttons f.

Setting the lock function

With the lock function you can block access to all configuration menus.

1.Hold down the S button r for a little longer than 3 seconds.

2.With the or button t select „SYSTEM SETUP“ and confirm with the OK button l.

3.With the or button t select “LOCK SETUP and confirm with the OK button l. The LCD display q shows the current settings.

4.With the or button t now select between „LOCK“ (Block) or „UNLOCK“ (Unblock).

5.With the OK button l you save the setting. In the LCD display q „LOCK SETUP“ then appears again.

System reset

With this function you can delete the assignment of all or individual device buttons.

1.Hold down the S button r for a little longer than 3 seconds. The notice "LANGUAGE SETUP" appears.

2.With the or button t select "SYSTEM SETUP" and confirm with the OK button l.

3.With the or button t select "SYSTEM RESET" and confirm with the OK button l.

4.With the or buttons t you can now select the desired function. To delete the assignments (Code) of all device buttons e, as well as all data to macros, timer and learned functions, select “ALL RESET” and confirm it with the OK button l.

5.In the LCD display q there now appears “CONFIRM RESET”. Confirm the deletion with the OK button l. Then the LCD display q shows “SUCCESS RESET”. The detailed information is now deleted and the menu is terminated.

6.To delete only the assignments of individual device keys e, select “MODE RESET” and then press the OK button l. The LCD display q now shows MODE” and asks you to

- 17 -

press the device button e whose assignment you want to delete. To conclude, “SUCCESS” briefly appears, then you will again read “MODE” in the LCD display. Now press any other further desired device buttons e to also delete their assignment.

7.Otherwise, you can exit the menu by pressing the EXIT button y.

Timer configuration

The URC offers 2 timer modes, sleep timer and event timer.

Sleep timer

1.Press the device button e for the device that is to be controlled (i.e. VCR).

2.Hold down the S button r for a little longer than 3 seconds. The notice "LANGUAGE SETUP" appears.

3.Press the or button t until "TIMER SETUP" is shown. Press the OK button l "TIMER SLEEP" appears in the LCD display q. Confirm the selection of this function with the OK button l.

4.Now, below to the right in the LCD display q blinks the minutes for the remaining time of the selected device. Set with the or button t the desired value from 1

to 99 minutes. Press the OK button l to confirm. With programmed sleep-timer the LCD display q shows “zz” on the right next to the time.

5.Position the remote control in such a way that your infrared signal can reach the device to be switched off. After expiration of the set time the remote control will switch the device off.

6.If you now press the S button r “SL” is shown in the display q below on the left.

Event timer

The remote control has 4 event timers available via which you are allowed to send out specific series of button combinations at designated times.

1.Hold down the S button r for a little longer than 3 seconds. The notice "LANGUAGE SETUP" appears.

2.With the or button t select "TIMER SETUP" and confirm with the OK button l. "TIMER SLEEP" appears in the LCD display q. With the or button t select the desired memory slot "TIMER SETUP 1" to "TIMER SETUP 4" and confirm with the OK button l.

3.Now the hour of the time of day, to which the desired button combinations are to be carried out, blinks. Set with the or button t the desired hour and press for confirmation the OK button l.

4.Now the minutes of the time of day, to which the desired button combinations are to be carried out, blinks. Set with the or button t the desired minutes and press for confirmation the OK button l.

- 18 -

5.In the LCD display q you will see "TIMER X KEY" (X stands for the desired timer). Now press the desired device button e followed by the desired sequence of the button commands.

6.By default, the timer commands are sent at intervals of 1 second. Since many devices react sluggishly, it is possible that the sequences of the timer commands are sent to the device too quickly. Then you have the option of programming, before a button command, a pause of between 5 to 21 seconds. For this press, if necessary repeatedly, on the MACRO button i. Below and to the right the LCD display q shows the current pause length in seconds.

7.Press the S button r to save your entry and to return to the timer menu.

8.Procede in a similar manner in order to, if required, programme the other timer memory slots also.

9.With programmed event timer the LCD display q shows the timer symbol „” on the right next to the time.

Tips:

1.Per timer memory slot a maximum of 14 buttons can be programmed. After entry of the 14th button the sequence will be automatically saved and "FULL" is shown in the LCD display q.

2.In this menu also the device will return to the standard display after approx. 15 seconds without an entry.

Delete Timer

You can delete a programmed sleep or event timer as follows:

1.Select the timer that you wish to delete (see chapter Sleep-Timer/Event-Timer) and then press the OK button l. In the LCD display q you will read „TIMER CLEAR“.

2.Press the OK button l. The LCD display q changes to „CONFIRM CLEAR“.

3.Press the OK button l once again to delete the timer. The LCD display q confirms the successful deletion with the message „SUCCESS“.

Learn configuration

The Universal remote control (URC) can learn and save button signals of an original remote control. If the URC does not work after applying the programming methods already described or cannot carry out all commands please attempt to teach the URC with the help of the original remote control.

•Use new batteries for the URC and the original remote control.

•Maintain a distance of at least one metre from other light sources. The light sources could disrupt the infrared transmission.

•Place the URC and the original remote control at a distance of 20 to 50 mm from each other on an even surface so that the infrared diodes 2) are facing each other.

- 19 -

Tips:

1.Do not use the following buttons for the learn function: all device buttons e, MACRO i, S button r, EXIT y.

2.If when teaching, during the notice "LEARNING", no button is pressed on the original RC after 25 seconds the learn menu will end. This mode can not be ended

by pressing a button on the URC.

3.The memory can accommodate 150 button commands.

If the memory is full the LCD display q shows "LEARN FULL" and the learn mode will end.

4.With the EXIT button y you return to the previous status (except with a notice of "LEARN KEY" and/or "LEARNING").

Code learn function

1.Press the device button e for the device that the URC should learn a button code.

2.Hold down the S button r for a little longer than 3 seconds. The notice "LANGUAGE SETUP" appears.

3.With the or button t select the menu "LEARN SETUP" and then press the OK button l.

4.In the LCD display q "LEARN SET" appears. Then press the OK button l. In the LCD display q "LEARN KEY" appears.

5.First press the button on the URC that is to be taught. In the LCD display q "LEARNING" appears. The URC now waits for the infrared signal from the original remote control.

Note:

Should the notice not change to "LEARNING" you have selected a button for which no button code can be taught.

6.Point the infrared sensors 2) of both remote controls towards each other.

7.Now hold down the desired button of the original remote control until "SUCCESS" or "LEARN ERROR" appears in the display q of the URC.

8.If in the LCD display q "SUCCESS" appears (process successful), you can teach further buttons begining with step 5. If "LEARN ERROR" appears (process unsuccessful) repeat the process in any case from step 5.

9.To stop/end the learn process press the S button and subsequently, while “LEARN KEY” is displayed, repeatedly the EXIT button y until the normal indicator appears in the LCD display q. During the displayed “LEARNING” simply allow 30 seconds to pass without any operation and the device will then exit the menu.

Delete all programmed buttons of all devices

1.Hold down the S button r for a little longer than 3 seconds. The notice "LANGUAGE SETUP" appears.

2.With the or button t select the menu "LEARN SETUP" and then press the OK button l. In the LCD display q "LEARN SET" appears.

- 20 -

3.With the or button t select "LEARN CLEAR" (taught delete) and confirm with the OK button l. In the LCD display q "CONFIRM CLEAR" (confirm delete) appears.

4.Confirm with the OK button l. In the LCD display q

"SUCCESS" appears. All programmed buttons are deleted. Finally the menu will automatically end.

Note:

When the LCD display shows “CONFIRM CLEAR” you can stop the deletion with the EXIT button y.

Macro configuration

With the MACRO function up to 16 button commands can be carried out with the press of a single button, that is to say, several previously saved control commands can be deleted with one MACRO button. There are 6 Macro memory slots available for you.

To programme a Macro

For Macro programming proceed as follows:

1.Hold down the S button r for a little longer than 3 seconds. The notice "LANGUAGE SETUP" appears.

2.With the or button t select "MACRO SETUP" and confirm with the OK button l. In the display "MACRO SETUP 1" appears.

3.With the or button t select the memory slot to be programmed (MACRO SETUP 1 - 6) and confirm with the OK button l.

4.In the LCD display q "MACRO STEP" appears. Now press, one after the other, the desired buttons (max. 16). The sequence should begin with a device button e.

5.By default the Macro commands are sent in intervals of 1 every second. Since many devices react sluggishly it is possible that the sequence of the Macro commands are sent too quickly to the device. Then you have the option of programming, before a button command, a pause

of between 5 - 21 seconds. For this purpose press, if necessary repeatedly, the MACRO button i. Below

and to the right the LCD display q shows the current pause length in seconds.

6.When the maximum number of button commands is reached the LCD display q shows "FULL".

7.Save the entry with the S button r. In the LCD display q "MACRO SETUP" appears.

8.If, with the selection of the Macros to be programmed (step 3), you select a memory slot that is already occupied the existing Macro will be overwritten.

9.Repeat the process from step 3 to create further Macros.

10.With the EXIT button y you move back a level in the menu, except during the input of the button commands.

- 21 -

Tips:

1.A maximum of 16 button commands can be saved in a Macro. After input of the 16th button command, “FULL” appears in the LCD display q.

2.To exit the mode without saving allow approx. 15 seconds to pass without an entry.

3.In the mode "MACRO STEP" you can only return to the previous status with the S button r.

Example: You want to save a command chain in a Macro. We begin in the mode "MACRO STEP".

Desired command chain: Switch on TV => PAUSE => switch to the AV input => switch on DVD => PAUSE => Playback DVD.

In the mode "MACRO STEP", for this you enter the following button commands:

=> => (Pause time) => => =>

=> (Pause time) =>

Execute a Macro

To execute a pre-programmed Macro proceed as follows:

1.Press the MACRO button i.

2.With the corresponding number button o you access the desired Macro (1-6). Example: If Macro 3 is to be implemented press first the Macro button i and then, within 5 seconds, the number button "".

To delete all Macros

To delete all pre-programmed Macros proceed as follows:

1.Hold down the S button r for a little longer than 3 seconds. The notice "LANGUAGE SETUP" appears.

2.With the or button t select "MACRO SETUP" and confirm with the OK button l. In the display "MACRO SETUP 1" appears.

3.With the or button t select "MACRO CLEAR" and confirm with the OK button l.

4.In the LCD display q "CONFIRM CLEAR" (confirm delete) appears. Confirm the delete process with the OK button l. The LCD display q shows "SUCCESS". All Macros are now deleted and the menu will end.

Tips:

1.When the LCD display q shows "CONFIRM CLEAR" you can stop the delete process with the EXIT button y.

2.Individual Macros can not be deleted they can only be overwritten.

Favourites channel

Note:

With this function you can save your preferred stations as favourites.

- 22 -

To programme favourites

Your favourite stations are saved as follows:

1.Press the device button e for the device that you want to save a favourite.

2.Hold down the S button r for a little longer than 3 seconds. The notice "LANGUAGE SETUP" appears.

3.With the or button t select "FAV CH SETUP" and confirm with the OK button l. In the display "FAV CH 1 SETUP" appears.

4.With the or button t select the memory slot to be programmed (FAV CH 1 - 4 SETUP) and confirm with the OK button l.

5.In the LCD display q "FAV CH STEP" appears. Now press, one after the other, the buttons (max. 4) for access to your desired favourite stations.

6.When the maximum number of button commands is reached the LCD display q shows "FULL".

7.Save the entry with the S button r. In the LCD display q "FAV CH SETUP 1 - 4" appears.

8.If, with the selection of the favourites to be programmed (step 4), you select a memory slot that is already occupied the existing favourite will be overwritten.

9.Repeat the steps to apply further favourites.

10.With the EXIT button y you move a level backwards in the menu except during the entry of the button commands.

Note:

The input of the channel numbers can vary according to the model and brand of the selected devices. If necessary, with multi-digit channel numbers you must first press the button a.

To access favourites

To access a pre-programmed favourite press the FAV/EPG button 1( followed by the corresponding number button for the desired memory slot (1 - 4).

Delete All FAV channels

To delete all pre-programmed favourites proceed as follows:

1.Hold down the S button r for a little longer than 3 seconds.

2.With the or button t select "FAV CH SETUP" and confirm with the OK button l. In the display "FAV CH 1 SETUP" appears.

3.With the or button t select "FAV CH CLEAR" and confirm with the OK button l.

4.In the LCD display q "CONFIRM CLEAR" (confirm delete) appears. Confirm the delete process with the OK button l. The LCD display q shows "SUCCESS". All favourites are now deleted and the menu will end.

Tips:

1. When the LCD display q shows "CONFIRM CLEAR" you can stop the delete process with the EXIT button y.

- 23 -

2.Individual favourites can not be deleted they can only be overwritten.

Volume control

Vol +/—, (Mute switching)

Press the "VOL+" button to increase the volume. With the "VOL —" button you reduce the volume. To mute the sound press the -button h. A further press of this button turns the sound back on.

If you have not set any other device as the target for the global volume control, when you press the VOL +/- buttons j on the URC the volume control of the TV set is addressed by default, regardless of which device button e was previously pressed. However, this does not apply to the following devices: “AMP”, “DVD”, and “DSAT” since it can be assumed that these devices are equipped with their own volume control.

For operation

>>To operate one of the programmed devices with the URC first press the corresponding device button e. Then point the URC to this device and press the desired button.

>>Put the number buttons o exactly as you do with the original remote control. Before you make a two digit entry press, if necessary, the button a.

>>Press the S button r and subsequently the FAV/EPG button 1( to start the electronic programme guide of a device equipped with this function.

>>If you press the S button r the date is superimposed for 10 seconds in the LCD display q below and on the right.

>>Whilst you hold down one of the device buttons e the active code for this device will be superimposed below to the right in the LCD display q.

>>Via the MENU button k you access the dialogue for the setting of the respective target device.

>>Press the illumination button d to switch the display and button illuminations on and/or off.

All OFF

Tips:
With the button	ALL OFF (all off) w all devices that

are switched on can be automatically switched off. This function can switch on again devices that have already been switched off (depending on the device). For this, press and hold the ALL OFF button w for a few seconds. It may take up to 10 seconds before all devices are switched off. This will only function under the following circumstances:

1.A visible connection exists between all the devices and the URC.

- 24 -

2.Automatic code search, brand code search and MACRO function are not active.

3.All target devices must be suitable for remote control switch off.

To again switch on all devices automatically hold down once more the button w until all devices are switched on.

Cleaning and storage

Attention!

Ensure that moisture cannot permeate into the device during cleaning! Otherwise there is the danger of causing irreparable damage to the device!

>>Clean the housing of the device exclusively with a soft moist cloth and a mild dishwashing detergent.

>>Store the device exclusively in an environment that complies with the specifications given in the technical data.

>>Before storing remove the batteries so that they will not cause damage to the device if, during storage, they happen to leak.

Faults / Remedies

Your device does not react to the URC.

>>Check the batteries. They must have enough voltage and be properly installed.

>>Firstly have you pressed the correct device button e for the desired target device?

>>Check to see that the correct code is programmed in for the target device (see section "Code Setup").

The URC is transmitting the commands incorrectly.

>>Press the corresponding device button e to set the URC to the correct mode.

>>The batteries must have enough voltage and be properly installed.

>>It is possible that you are using the wrong code. Start the brand code search, the automatic code search or the direct code input (manual).

The URC does not change the station on the device.

>>Press the corresponding device button e to set the URC to the correct mode.

>>In the event that the original RC does not have a "-/- -" button, change the programme with the P +/— buttons u or the number buttons o.

>>If this also does not work the child protection for the target device could be activated.

Some buttons on the URC do not function properly.

>>It is possible that your URC does not have all of the functions that are on the device's original remote control.

- 25 -

>>It is possible that you have not programmed in the optimal code. Search for a code that supports more of the target device's functions.

The URC stops reacting after a button is pressed.

>>The batteries must have enough voltage and be properly installed.

>>Point the URC towards your device.

The LCD display q shows nothing.

>>The batteries must have enough voltage and be properly installed.

>>The contrast could be set too low. Increase the contrast setting.

Disposal

Do not dispose of the device in your normal domestic waste. This product is subject to the European directive 2002/96/EC.

Universal remote control

•Have the universal remote control or parts of it disposed of by a professional disposal company or by your communal disposal facility.

•Observe the currently applicable regulations. In case of doubt contact your disposal facility.

Batteries/rechargeable batteries

•Used batteries/rechargeable batteries may not be disposed of in household waste.

•Batteries can contain poisons which are damaging to the environment. Therefore, dispose of the batteries/rechargeable batteries in accordance with statutory regulations.

•Every consumer is legally obliged to surrender batteries/ rechargeable batteries to a community collection centre in their district or to a dealer. The purpose of this obligation is to ensure that batteries are disposed of in a nonpolluting manner.

•Only dispose of batteries when they are fully discharged.

Packaging

• Dispose of packaging materials in an environmentally responsible manner.

Technical data

Controllable devices:	10
Dimensions
L x W x H:	217 x 50 x 22 mm
Weight :	133 g (incl. batteries)
Infrared LED:	Laser class 1
Power supply
Batteries:	2 x 1.5 V, type AAA/LR03 (micro)
	(supplied)
	- 26 -

Operating temperature: +15 – +35 °C

Storage temperature : —0 – +50 °C

Humidity:

≤ 75 % (No condensation)

Note regarding conformity

This device satisfies the fundamental requirements and other relevant regulations of the EMC Directive 2004/108/EC and the RoHS Directive 2011/65/EU.

Importer

KOMPERNASS GMBH

BURGSTRASSE 21

44867 BOCHUM, GERMANY www.kompernass.com

Warranty & Service

You receive a 3-year warranty for this appliance as of the purchase date. This appliance has been manufactured with care and meticulously examined before delivery.

Please retain your receipt as proof of purchase. In the case of a warranty claim, please make contact by telephone with our service department. Only in this way can a post-free despatch for your goods be assured.

The warranty covers only claims for material and manufacturing defects, but not for transport damage, wearing parts or for damage to fragile components, e.g. buttons or batteries.

This product is for private use only and is not intended for commercial use. The warranty is void in the case of abusive and improper handling, use of force and internal modifications not carried out by our authorized Service Centre.

Your statutory rights are not restricted in any way by this warranty.

The warranty period is not extended through repairs made under warranty. This applies also for replaced or repaired parts. Any damages or deficiencies found on purchase must be reported as soon as possible after unpacking, at the latest two days after purchase. On expiry of the warranty, all repairs carried out are subject to payment.

Service Great Britain

Tel.: [phone] (£ 0.10/Min.)

E-Mail: [e-mail]

IAN 86342

Service Ireland

Tel.: [phone]

(0,08 EUR/Min., (peak))

(0,06 EUR/Min., (off peak)) E-Mail: [e-mail]

IAN 86342

- 27 -

- 28 -