Side-Power PJC211, PJC212, PJC221, PJC222 Installation And User Manual

Keep this

manual onboard !

Installation and user's manual

EN

Made in Norway

©

Sleipner Motor AS 2013

SLEIPNER MOTOR AS

P.O. Box 519
N-1612 Fredrikstad
Norway
Tel: [phone]
Fax: [phone]

www.side-power.com
[e-mail]

PJC211/212/221/222
S-link Control Panel

SIDE-POWER

Thruster Systems

v 2.0.2

2

PJC211/212/221/222 2.0.2 - 2013

DO NOT connect any other control equipment to the S-link controlled products except
Side-Power original S-link products or via a Side-Power supplied interface product made
for interfacing with other controls. Any attempt to directly control or at all connect into
the S-link control system without the designated and approved interface, will render all
warranties and responsibilities for the complete line of Side-Power products connected
void and null. If you are interfacing by agreement with Sleipner and through a designated
and approved interface, you are still required to also install an original Sidepower control

panel to enable efcient troubleshooting if necessary

DECLARATION OF CONFORMITY

We, Sleipner Motor AS
P.O. Box 519
N-1612 Fredrikstad, Norway
declare that this product with accompanying
standard remote control systems complies with
the essential health and safety requirements
according to the Directive 89/336/EEC of 23
May 1989 amended by 92/31/EEC and
93/68/EEC.

Product Features ................................................................................................................................................................................. 3

Panel layout ........................................................................................................................................................................................ 4

Panel layout ........................................................................................................................................................................................ 5

Display in normal use ......................................................................................................................................................................... 6

Display when alarms ........................................................................................................................................................................... 7

Setup procedure .................................................................................................................................................................................. 8

Menu system ....................................................................................................................................................................................... 9

Alarm descriptions ............................................................................................................................................................................ 16

S-link system example....................................................................................................................................................................... 18

Measurements / Cut-out template ..................................................................................................................................................... 19

Connections for external buzzer ........................................................................................................................................................ 19

CONTENTS

3

PJC211/212/221/222 2.0.2 - 2013

PJC-211/212/221/222

Control panel with S-link™ CAN-bus connection

Product features

• For proportional thruster control with DC, AC and Hydraulic Thrusters (Hydraulic thrusters PJC-221/222 only).

• Finger tip control speed control with purpose designed joysticks

• Hold - function for easy docking, runs thrusters at selected power (Dual joysticks PJC-212/222 only)

• Back-lit LCD display with instant feedback

- System status / alarms

- Amount of thrust & direction of thrust

• Interactive multi-language menus

• CAN-Bus communication with thrusters and accessories

• Plug & play cables with compact connectors

• Diagnostics and system setup via panel

• Built-in audible alarm “buzzer”

• Connector for external “buzzer”/loud audible alarms

• Supports Side-Power retractable thrusters with or
without Speed Control

4

PJC211/212/221/222 2.0.2 - 2013

MENU

Speed control joystick for

bow thruster

Speed control joystick for

stern thruster

Information display, see
following pages for
details.

Press both “ON” buttons
simultaneously to
activate control panel.

Press to change
between day and
night light

Press and hold for 3
seconds to access
menu system and
choose items in menus

Press to de-activate
control panel or cancel or
go back in menu system
or mute internal alarm

buzzer

MENU

Speed control joystick for

thruster

Information display, see fol­lowing pages for
details.

Press both “ON” buttons

simultanously to activate
control panel.

Press to change
between day and
night light

Press and hold for 3
seconds to access menu
system and choose items
in menus

Press to de-activate
control panel or cancel or
go back in menu system
or mute internal alarm

buzzer

Panel Layout, PJC-211

Panel Layout, PJC-212

Holding function for auto-

running of bow and stern
thrusters together in the
direction of the arrows at
selected power

Press “+” for more and “-”
for less power (6 steps).

If any control unit are
running the thruster in op­posite direction to the hold
function, the hold function
will be deactivated.

5

PJC211/212/221/222 2.0.2 - 2013

STOP

front s_v strek_PJC222.pdf 1 04.11.2010 11:05:34

Speed control joystick for

thruster

Information display, see fol­lowing pages for details.

Press and hold “ON”
button for 1 second to

activate control panel.

Press to change
between day and
night light.

Press and hold for
3 seconds to enter
menu system

Emergency stop
button

Press to de-activate
control panel or cancel or
go back in menu system.

Mute buzzer alarm

STOP

front s_v strek_PJC222.pdf 1 04.11.2010 11:05:34

Speed control joystick for

bow thruster

Speed control joystick for

stern thruster

Holding function for auto-

running of bow and stern
thrusters together in the
direction of the arrows at
selected power

Press “+” for more and “-”
for less power (6 steps).

If any control unit are
running the thruster in op­posite direction to the hold
function, the hold function
will be deactivated.

Information display, see
following pages for details.

Press and hold “ON” button

for 3 seconds to activate
control panel.

Press to change
between day and
night light.
Press and hold for
3 seconds to enter
menu system

Emergency stop
button

Press to de-activate
control panel or cancel or
go back in menu system

Panel Layout, PJC-221

Panel Layout, PJC-222

6

PJC211/212/221/222 2.0.2 - 2013

Status indicators for bow

thruster. (Port bow thruster in

a dual bow thruster setup)

Runtime indicator will be

shown here in a single DC

electric bow thruster setup

Status indicators for stern

thruster. (Port bow thruster in

a dual stern thruster setup)

Runtime indicator will be

shown here in a single DC

electric stern thruster setup

Status indicators for starboard
bow thruster. Only shown in a
dual bow thruster setup.

Battery indicator will be shown
here in a single DC electric bow

thruster setup

Status indicators for starboard
stern thruster. Only shown in a
dual stern thruster setup.

Battery indicator will be shown
here in a single DC electric stern

thruster setup.

DISPLAY IN NORMAL USE:

BOW

STERN

BOW-STB

STERN-STB

Examples of display for different panel applications:

PJC211/221:
DC Electric Bow thruster

PJC221:
Hydraulic Bow thruster

PJC221:
AC Electric Bow thruster

PJC212/222:
DC Electric Bow thruster
DC Electric Stern Thruster

PJC222:
Hydraulic Bow thruster
Hydraulic Stern Thruster

PJC222:
AC Electric Bow thruster
Hydraulic Stern Thruster

PJC211/221:
DC Electric Stern thruster

PJC212/222:
Dual DC Electric Bow thrusters
Dual DC Electric Stern thrusters

PJC222:
Dual Hydraulic Bow thrusters
Dual Hydraulic Stern thrusters

PJC222:
Dual AC Electric Bow thrusters
Dual AC Electric Bow thrusters

PJC221:
Dual AC Electric Bow thrusters

PJC221:
Dual Hydraulic bow thrusters

7

PJC211/212/221/222 2.0.2 - 2013

Battery indicator.
From 8.5V to 12V for 12V thrusters,
15V to 24V for 24V thrusters

Motor temperature indicator.

From 70°C to 130°C

INDICATORS FOR DC Thrusters:

INDICATORS FOR AC Thrusters:

INDICATORS FOR Hydraulic Thrusters:

Motor temperature indicator.

Hydraulic oil temperature indicator.

INDICATORS FOR Retractable Thrusters:

Symbol shown when the thruster deploys

Symbol shown when the thruster retracts

Symbol shown when the thruster is in
position OUT

When the thruster is deployed and no

input is given via the joysticks/buttons
over a 10 second period, the panel will
give a audible signal every 10th second

to tell that the truster is still deployed.

Thrust power and direction, Bow thruster(s)

Input from bow joystick on this panel.

The thrust indicator will be shown in this position on a single

joystick panel if the thruster is dened as a bow thruster

Indicating amount of thrust set by other control units in the

system, i.e additonal PJC panels, 8700 Retract panel, input
via 8730 S-link external switch interface, S-link remote con-

trol etc.

If two or more units is set to run the thruster in
opposite direction, this information will not be shown.

FIRST TIME SETUP

After installation of a S-link thrusters system, a System Setup procedure to setup control panels, thrusters and

additional equipment must be completed (ref. procedure on page 10) before the system can be used.

Thrust power and direction, Stern thruster(s)

Input from stern joystick on this panel

The thrust indicator will be shown in this position on a single

joystick panel if the thruster is dened as a stern thruster.

Battery indicator.
From 8.5V to 12V for 12V thrusters,
15V to 24V for 24V thrusters

Motor temperature indicator.

From 70°C to 130°C

Symbol shown when a DC Thruster is
used in a dual bow or dual stern setup:

INDICATORS showing thrust direction and amount:

8

PJC211/212/221/222 2.0.2 - 2013

DISPLAY WHEN ALARMS:

When there is a problem or a fault, the panel will show this alarm situation by changing LCD display backlight to

red color.

The panel will also change to show “Alarm Info” on the bottom of the screen, indicating that by press­ing the corresponding button below, you will get information about what the problem is (examples below).

MENU

Voltage below 9.3V/17.5V (12V/24V system) or temperature above 85oC (80oC for PPC800 FW V1.013 or
older/ SR150000 FW V1.006 or older): Single short beep every 2.4 seconds

Voltage below 8.9V/16.3V (12V/24V system) or temperature above 100oC (90oC for PPC800 FW V1.013 or
older/ SR150000 FW V1.006 or older): Two short beeps every 2.4 seconds

Voltage below 8.5V/15V (12V/24V system) or temperature above 115oC (100oC for PPC800 FW V1.013 or
older/ SR150000 FW V1.006 or older): Red backlight in display and continous short beeps.

If one or more of the thrusters enters an alarm state - Voltage below 8 Volts (both 12 and 24 Volt sys­tems) or temperature above 130oC (110oC for PPC800 FW V1.013 or older/ SR150000 FW V1.006 or older):

Continuous beeps, and the “HOLD” function will be cancelled and both thrusters will stop. Temperature must drop
below 115oC (100oC for PPC800 FW V1.013 or older) before the thruster can be operated again.

STOP

front s_v strek_PJC222.pdf 1 04.11.2010 11:05:34

(Button below this
symbol pressed)

No. of alarms

Alarm code

Alarm description

Reset alarm
and Return

Use joystick to scroll if

more than two alarms

Scroll bar

Name and
location of
device

Refer to Alarm code overview/table on pages 18-19 for

full description on the different alarm codes.

When using the “HOLD” function,

the internal and external (if tted) buzzer will give the following warning signals:

9

PJC211/212/221/222 2.0.2 - 2013

STOP BUTTON

Pressing the STOP button on a hydraulic panel will operate the dump valve and

the thruster will stop. NB: FOR EMERGENCY USE ONLY

Panel will not run thrusters.
Pressing button below will mute buzzer alarm at all panels and show

the alarm info screen.

SPECIFIC ALARMS

WARNING! HIGH SPEED. STABILIZER NOT ACTIVE!

(Only for yachts equipped with a Side-Power Stabilizer system)
Warning will show when yacht is driven at high speed with stabilizer system inac-

tive. Please refer to the Stabilizer ECU manual for speed settings.

Pressing button below will mute buzzer alarm at all panels and show
the alarm info screen.

ALARMS (AC & HYDRAULIC THRUSTERS):

When there is a problem or a fault, the panel will show this alarm situation by the LCD display in red color.
All alarms will show in display when panel is turned OFF. This requires the S-link and other system devices has
power. Critical alarms are also trigging internal and external buzzer (a long beep every 2 seconds). The buzzer can

be silenced by pushing the button below , this will also silence all other panels in the system

Critical alarms: LOW OIL LEVEL, HIGH OIL TEMPERATURE, EMERGENCY STOP, HIGH SPEED STABILIZER NOT AC­TIVE and HYDRAULIC AC MOTOR POWER PACK OVERTEMP, AC THRUSTER OVERTEMP, AC THRUSTER FAIL, STABI­LIZER FAULT

For safety!
When oil pressure goes below 10bar, the HOLD function are deactivated.

ALARM SHOWN ON INACTIVE PANELS!

This screen will be shown on inactive panels if any of the following critical alarms

occur:
LOW OIL LEVEL, HIGH OIL TEMPERATURE, HYDRAULIC AC MOTOR POWER PACK
OVERTEMP, AC THRUSTER OVERTEMP, AC THRUSTER FAIL

Pressing button below will mute buzzer alarm at all panels and show
the alarm info screen.

10

PJC211/212/221/222 2.0.2 - 2013

SETUP PROCEDURE

RUN SETUP! DEVICES IN CONFLICT!

Detectet devices in conict. Two or more thrusters dened as same instance
(bow/stern/bow STB/Stern STB). Run Setup procedure to correct.

Thrusters can not be operated until seup is completed.

SETUP DO NOT MATCH SYSTEM. FOR AUTO SETUP

New devices found. Not in conict with other devices.

Press button below the -symbol to auto setup.

Thrusters can not be operated to auto setup is completed.

The setup procedure requires knowledge of the serial numer and location of all the S-link
devices.

Write this down in the form on the last page to have the information at hand when doing a
manual setup.

Press and hold the button marked “MENU” for 3 seconds to enter the menu sys­tem. Use the (stern) joystick to select “SETUP”, Press button below the

-symbol to enter the”SETUP”-menu.

Use the (stern) joystick to select “SYSTEM DEVICES”,
Press button below the -symbol to enter the”SYSTEM DEVICES”-menu.

Use the (stern) joystick to set the pin code one number at the time,
press button below the -symbol to jump to next number and conrm.
The pin code is “9 9 9 9”.

NOTE: Re-entering the SYSTEM DEVICES menu within 15 minutes does not
require entering PIN code

The devices found in the system is now displayed with their instance and serial
number.

Go through all devices and make sure that they are set to the correct instance
and function (refer to detailed instructions in the SETUP section of “Menu
System”-chapter).

Press button below the -symbol to save setting and return to “Setup”-
Menu.

At the rst startup of a new system, one of the two screens below will be shown:

11

PJC211/212/221/222 2.0.2 - 2013

MENU SYSTEM:

Access menu system by press and hold
Menu button for 3 seconds

Move around in menus by using joysticks

Follow instructions on the screen and
press the buttons below the symbols indi­cated on LCD screen

LANGUAGE

STOP

front s_v strek_PJC222.pdf 1 04.11.2010 11:05:34

MENU

LANGUAGE

Choose language by moving joystick:
English, Norwegian, German, French, Spanish and Italian.

Press the button below to set the language to the highlighted

menu entry. A star (*) on each side indicated the laguage set.

BUTTON SYMBOLS

On the bottom line of the display, a symbol will be shown over the buttons below.
These symbols will show what function each corresponding button have in the selected menu entry.

: Return to previous menu.
: Select highlighted menu text / Save edited parameter.
: Edit highlighted parameter.
: Cancel editing without saving.

: This symbol indicates that the (stern) joystick is used to move between menu items /parameters.

MAIN MENU ITEMS:

Move between main menu items with the (stern) joystick.

STABILIZER

STABILIZER

(Shown only for yachts equipped with a Side-Power Stabilizer system)

Press the button below to edit the selected parameter.

ON/OFF will start to blink, use joystick to alter value.

Press the button below to save edited parameter to device.

STABILIZER:
Values: ON/OFF

Switches the stabilizer ON or OFF.

AnySpeed:

Values: ON/OFF

Switches the zero speed/at anchor stabilization ON or OFF.

(Default in systems

with stabilizers)

12

PJC211/212/221/222 2.0.2 - 2013

SETUP

SETUP

Move between menu items with the (stern) joystick.

Press the button below to select the highlighted menu entry.
Press the button below to return to the previous menu.

Setting done under SETUP will be sent to all other panels in the
system.

SYSTEM DEVICES

View all devices (except PDC1001) connected to S-Link and manu­ally change setup values.

1

PDC100 must be setup by authorized personnel.

A PIN code is required to enter the SYSTEM DEVICES menu.
Use the (stern) joystick to set the pin code one number at the time,
press button below the -symbol to jump to next number and
conrm. The pin code is “9 9 9 9”.

The number of devices found is shown in the upper right corner of
the display.

Use (stern) joystick to move between the installed devices.

The list of devices found can ll more than one screeen. A scroll

bar indicates the position of the selected item.

NOTE: Re-entering the SYSTEM DEVICES menu within 15 minutes

does not require entering PIN code

(Default in systems

without stabilizers)

PHC 024 (Controller for hydraulic thrusters)

Most functions requires PHC 024 with rmware V.1.101 or

newer!

Move between PHC-024 parameters with the (stern) joystick.

Press the button below to return to the previous menu.
Press the button below to edit the selected parameter.

Parameter value will start to blink, use joystick to alter value.

Press the button below to save edited parameter to device
Press the button below to cancel editing without saving.

Bow/Stern Direction:

Values: Normal (default)/Inverted

Switches between Normal and Inverted running direction for the
thruster

Pump Control (PTO Mounted Pump)
Values: Auto(default)/Always ON

When «Pump Control» is set to «Power save», the system will auto-

matically control load sharing between two PTO pumps by deactivat-

ing the second PTO pump when not needed (two PTO pumps/control
valves required) to reduce heat generation in the system and save
fuel/energy.

When any thruster is running, both PTO pumps will be active to en-

sure good performance. When a SPS stabilizer system is active, one
PTO pump will be deactivated to save power. If stabilizers are active
and the system pressure drop below 80bar, the system will activate
the second PTO pump for 15 minutes to increase the ow capacity
and maintain required pressure. After 15 minutes the second pump
will be deactivated unless the pressure is still below 80 bar.

NB: “Pump Control: Power Save” must only be used on PHC

024 with rmware V.1.008 or newer!

13

PJC211/212/221/222 2.0.2 - 2013

Cooling Signal Output

Values: Normal (default)/Inverted

Set to Normal when using a hydraulic cooling pump.
Should be set to Inverted when using an electrical cooling pump with

a 10 2380A-12/24V relay box

SETUP cont.

Cooling Power Save

Values: ON (default)/OFF

ON sets the Cooling Pump into power save mode,which means the
Cooling Pump output is dropping to 0 volt when the oil pressure is be­low 10 bar for more than 10 seconds (Cooling Pump are turned OFF).

Tank Monitor

Values: ON (default)/OFF

ON is when you have a tank monitor, oil level and Oil temp sensor.

OFF is when you do not have a tank monitor and the display will show
0°C and no alarm for high temperature or low level will not be trans-

mitted on the S-link.

Instance

Values: --(default)/PORT/STARBOARD

Setting the PHC024 tank controller instance. For a mono hull boat
the instance should be ”--“. If you have an catamaran with two
PHC024 controllers then the one in the port hull should be set as
“PORT” and the one in the starboard hull as “STARBOARD”. This

way the two controllers are shown in the panel display as two
different oil tanks to monitor.

Main Switch

Press the button below to return to the previous menu.
Press the button below to edit the selected parameter.

Parameter value will start to blink, use joystick to alter value.

Press the button below to save edited parameter to device
Press the button below to cancel editing without saving.

Location

Values: BOW/STERN/BOW-STB/STERN-STB

Set the location for selected device. Use BOW or STERN in a conven-

tional thruster system. In a system with two bow or stern thrusters

(i.e a catamaran), use BOW or STERN for port thruster, BOW-STB or
STERN-STB for starboard thruster

Cooling Pump

Values: Always Running/Temp Controlled(default)

When the option “Temp Controlled” is selected, the cooling pump will
start when oil temperature exceeds 50°C and stop when the oil tem­perature goes below 40°C.

On systems with two oil tanks, this setting will apply to both tanks.

14

PJC211/212/221/222 2.0.2 - 2013

PPC800 (DC Speed Control)
SR150000 (Control unit for SRV80/SRV100/SRV130/SRV170/SRV210/SRH)
SR61242 (Control unit for SR80/SR100)

Move between parameters with the (stern) joystick.

Press the button below to return to the previous menu.
Press the button below to edit the selected parameter.

Parameter value will start to blink, use joystick to alter value.

Press the button below to save edited parameter to device
Press the button below to cancel editing without saving.

Location

Values: BOW/STERN/BOW-STB/STERN-STB

Set the location for selected device. Use BOW or STERN in a conven-

tional thruster system. In a system with two bow or stern thrusters

(i.e a catamaran), use BOW or STERN for port thruster, BOW-STB or
STERN-STB for starboard thruster

SETUP cont.

Function

Values: SR(V) ON/OFF, SRP 80/100, SRVP 130-210, SEP 30-240,
SRVP 80/100, SRH, SRHP

Setup the control unit behaviour

SR(V) ON/OFF: Retract thruster without speed controller

(PPC800/PHC-024), SR61242 or SR150000.

SEP 30-240: Tunnel speed thruster, PPC800 without retract.

SRP 80/100: Retract SR61242 with PPC800, both devices

needs to be set to SRP 80/100.

SRVP 130-210: Retract SR150000 with PPC800, both de-

vices needs to be set to SRVP 130-210.

SRH: On/Off Hydraulic retract with crossover and no
need for PHC024 controller.

SRHP: Proportional Hydraulic retract. This needs the
PHC024 controller.

SRVP 80/100: Retract SR150000 with PPC800, both devices

needs to be set to SRVP 80/100.

Direction

Values: Normal (default)/Inverted

Switches between Normal and Inverted running direction for the
thruster

PPC800 SR150000 SR61242 PHC 024
SR(V) ON/OFF x x
SRP 80/100 x x
SRVP 130-210 x x
SEP 30-240 x
SRVP 80/100 x x
SRH x
SRHP x x

15

PJC211/212/221/222 2.0.2 - 2013

SETUP cont.

RCRS-1 (S-Link Radio Remote Receiver)
Move between parameters with the (stern) joystick.

Press the button below to return to the previous menu.
Press the button below to edit the selected parameter.

Parameter value will start to blink, use joystick to alter value.

Press the button below to save edited parameter to device
Press the button below to cancel editing without saving.

BOW/STERN Thrust

Values: 0-100% (Default 75%)

Set the amount of thrust given by the remote control.

In a bow/stern conguration, try to balance the thrust so that the

boat moves straight sideways when both thrusters are operated
simultanously with input from the remote only.

MSI8730 (S-Link Interface)
Move between parameters with the (stern) joystick.

Press the button below to return to the previous menu.
Press the button below to edit the selected parameter.

Parameter value will start to blink, use joystick to alter value.

Press the button below to save edited parameter to device
Press the button below to cancel editing without saving.

Thrust

Values: 0-100% (Default 75%)

Set the amount of thrust given by the remote control.

In a bow/stern conguration, try to balance the thrust so that the

boat moves straight sideways when both thrusters are operated
simultanously with input from the remote only.

Location

Values: BOW/STERN/BOW-STB/STERN-STB

Set the location for selected device. Use BOW or STERN in a conven-

tional thruster system. In a system with two bow or stern thrusters

(i.e a catamaran), use BOW or STERN for port thruster, BOW-STB or
STERN-STB for starboard thruster

HOLD CALIBRATION

Calibrates the HOLD-function to get balanced thrust from the bow

and stern thruster.

To start calibration, press the “+”-Hold button in the desired direc­tion. For a rst time calibration, the thrusters will start at 70%.

A system previously calibrated will start with the last amount of
thrust set.

One step on the Hold-button represents 1/6 if the calibrated value.

Adjust power with the joystick.

Press the button below to save the calibration values.
Press the button below to cancel calibration without saving.

16

PJC211/212/221/222 2.0.2 - 2013

INFO

INFO

Move between menu items with the (stern) joystick.

Press the button below to select the highlighted menu entry.
Press the button below to return to the previous menu.

THRUSTER INFO

Display info about the thusters in the system

The number of thrusters/controllers found is shown in the upper

right corner of the display.

Use (stern) joystick to move between the installed devices.

Press the button below to select the highlighted menu entry.
Press the button below to return to the previous menu.

The list of devices found can ll more than one screeen. A scroll bar

indicates the position of the selected item.
The joystick(s) operates the thrusters as normal while info is dis­played, this will be useful for troubleshooting, service and general
system diagnostics.

Panel INFO

Display info about the control panel

FW: Version number, Firmware
HW: Version number, Hardware
S/N: Serial number of the control panel
Voltage: S-link system voltage measured at the panel

Press the button below to return to the previous menu.

PPC800 (DC Speed Control)
SR150000 (Control unit for SRV80/SRV100/SRV130/SRV170/SRV210/SRH)
SR61242 (Control unit for SR80/SR100)

Motor Temp: Temperature measured at the electric motor brushes
(Not implemented in SR61242)
Contr. Temp: Temperature measured inside the controller
(Not implemented in SR61242)
Voltage: Motor Voltage measured at the controller
Thrust: Thrust level from joystick/hold buttons
A/kW: Motor Current and Effect reading measured at the
controller (PPC800 only)

Press the button below to return to the previous menu.

PHC024 (Controller for hydraulic thrusters)
Oil Pressure: Oil pressure measured at system oil tank
Oil Temp: Temperature measured inside the oil tank
Bow Thrust: Thrust level from joystick/hold buttons
Stern Thrust: Thrust level from joystick/hold buttons
FW: Version number, Firmware
S/N: Serial number of the PHC 024

Press the button below to return to the previous menu.

PDC100 (Controller for AC electric thrusters)
Motor Speed: RPM on motor output shaft
Motor Temp: Temperature measured in motor
Thrust: Thrust level from joystick/hold buttons

Press the button below to return to the previous menu.

17

PJC211/212/221/222 2.0.2 - 2013

DEFAULT

DEFAULT SETTINGS

Reset all settings to factory default - follow instructions on screen

Press the button below to conrm reset

The following parameters/values will be set to the factory settings:

Language = English

Backlight Level = 5
Backlight Night Color = Green
Backlight Nightlevel =1
Timer Auto-Off = 05 min

Hold Calibration =70% Bow and Stern

All system devices will be erased from memory.

(Setup procedure must be followed to recongure the system)

PANEL

PANEL SETUP

Move between parameters with the (stern) joystick.

Press the button below to return to the previous menu.
Press the button below to edit the selected parameter.

Parameter value will start to blink, use joystick to alter value.

Press the button below to save the edited parameter.
Press the button below to cancel editing without saving.

BACKLIGHT LEVEL

Values: 1-5

Set level of panel backlight in daylight mode. 1 is lowest inten­sity, 5 is the highest.

BACKLIGHT NIGHT COLOR

Values: GREEN, BLUE, RED, WHITE

Select color of backlight in nightlight mode

BACKLIGHT NIGHT LEVEL

Values: 1-3

Set level of panel backlight in daylight mode, 1 is lowest inten-

sity, 3 is the highest.

TIMER AUTO-OFF

Values: OFF, 01-60 min

Set the time from last use to auto panel shutdown.

Set from 1-60 minutes in 5 minute steps (1 minute steps from 1
to 5 minutes) or OFF (panel will not turn off automatically)

UNIT TEMPERATURE

Values: CELSIUS, FAHRENHEIT

Set the panel temperature displaying unit

18

PJC211/212/221/222 2.0.2 - 2013

ALARM DESCRIPTIONS

Errors shown in

display

Err.

No.

PPC

800

AMS

8977

SR80/100

SRV130-210

SRV80/100

SRH

PHC

024

SAC

Stabilizer

ECU

Descripon Acon

Motor Overcur-

rent

1 X Motorcurrent over 1400A Thruster must be serviced by au-

thorized personel, reset or PPC800

power OFF/ON

Motor Overtemp 2 X X Motortemp have been over 130°C

(110°C for PPC800 FW V1.013 or

older

and SR150000 FW V1.006 or older.)

Motor cool down below 115°C

(100°C for PPC800 FW V1.013 and

older and SR150000 FW V1.006 and

older)

Controller Over-

temp

3 X PPC800 temp have been over 80°C PPC800 cool down below 45°C

Controller Over-

temp

4 X SR150000 temp have been over

80°C

SR150000 cool down below 45°C

Low Voltage 5 X X X Low voltage on Motor Recharge battery, reset or device

power OFF/ON

Thermoswitch 6 X Motortemp have been over 110°C Motor cool down below 100°C

IPC Error 7 X X X Motor relay fault Turn off thruster battery main switch.

Thruster must be serviced by author-

ized personel, power OFF resets

alarm.

Critical Error 8 X PPC800 output fail PPC800 must be sendt for service

Low Motor Cur-

rent

9 X Thruster uses no power Check thruster connections or motor

dead!

Motor Contactor 10 X X No current on motor relay coil. Check motor relay connections, short

circuit or relay dead!

System Error 11 X X X X Fatal error Device must be serviced by author-

ized personel

No S-Link

Comm

12 X X X X X X No communication with device Check S-Link or power connections

Motor Temp

Sensor

13 X X X Motor temperature sensor fail Check for an open circiut on the

temp sensor on the motor

Supply Voltage

Fault

14 X No power Check power connections

Fuse Blown 15 X Fuse blown Replace fuse or check if main ca-

ble from battery and main cable to

thruster has been switched

Manual Over-

ride

16 X Main switch manually overridden Pull main switch

Motion OUT

Fault

17 X X Retract obstructed while deploying Turn off all panels. Go for lower

speed/deeper water and retry.

19

PJC211/212/221/222 2.0.2 - 2013

Errors shown in

display

Err.

No.

PPC

800

AMS

8977

SR80/100

SRV130-210

SRV80/100

SRH

PHC

024

SAC

Stabilizer

ECU

Descripon Acon

Motion IN Fault 18 X X Retract obstructed while retracting Turn panel on and manually override

main switch. Remove obstruction

and try again.

Actuator Fault 19 X X Actuator not getting any power Check actuator connection or power

to actuator. Reset alarm in alarm

menu on PJC 2xx or recycle power

Pos.Sensor

Fault

20 X Retract position sensor fail Check position sensor cables and for

sensor damage.

In Service Mode 21 X Retract controller in service mode Check dipswitch setting on retract

control box.

High Oil Temp 22 X Hydraulic oil temperature is higher

than 75°C

Stop running and wait for tempera-

ture to drop.

Check if cooling pump is running.

Low Oil Level 23 X Hydraulic oil lewel is to low Fill more hydraulic oil to the hydraulic

tank.

Warning Return

Filter

24 X Return lter element requiered

replacing

Warning Pres-

sure Filter

25 X Pressure lter element requiered

replacing

Warning High

Speed

26 X WARNING! High Speed.

Stabilizer not active!

Stabilizer Fault 27 X Any Stabilizer alarm. Se stabilizer panel for more info.

AC Motor Over-

temp

28 X Hydraulic AC motor power pack

overtemp. Higher than 120°C

AC Motor Sen-

sor Fail

29 X Hydraulic AC motor power pack

temp sensor open curicuit

Temperature

Warning

30 X X X High temperature warning.

Se manual for more details.

Motor Overtemp 31 X High temperature Alarm.

Se SAC manual for more details.

VFD Warning 32 X There is an warning from VFD.

Check VFD for more details.

VFD Not Ready 33 X The VFD is not ready.

Check VFD for more details.

VFD Fault 34 X VFD has an Alarm.

Check VFD for more details.

Warning Low

Voltage

35 X X Low voltage Warning!

Not Calibrated 36 X Drive shaft not aligned Calibrate drive shaft alignment, see

retract manual

20

PJC211/212/221/222 2.0.2 - 2013

+12/24V

-

5A

S-link on/off

switch

red

yellow

black

12/24V12/24V

Stern thruster

battery

Bow thruster

battery

Bow thruster

(SEP model)

Stern thruster

(SEP model)

-

black

+

red

B+

-

black

+

red

B+

Fixed multicable 5m

Fixed multicable 5m

5A

+12/24

5A

+12/24

PPC

PPC

Proportional

Power Controller

Proportional

Power Controller

PJC 212

Proportional

joystick

control panel

Bow and stern

Station 1

Automatic Main Switch

8977 12 / 8977 24

or

Manual main switch

w/ANL fuse

Automatic Main Switch

8977 12 / 8977 24

or

Manual main switch

w/ANL fuse

S-link control system

End terminator

End terminator

PJC 212

Observe PPC battery

terminal polarity !

S-link supply

S-link external

switch interface

and remote

(optional)

S-link external

switch interface

and remote

(optional)

Proportional

joystick

control panel

Bow and stern

Station 2

8730

8730

Sample S-link system

21

PJC211/212/221/222 2.0.2 - 2013









 













































































































Measurements

22

PJC211/212/221/222 2.0.2 - 2013

Supply

+12V / 24V DC

(S-link)

+

-

External alarm buzzer

12V / 24V DC - max 0,5A

Internal

fuse/relay

External alarm/buzzer connection

Re

a

r

s

i

d

e

o

f

p

a

n

e

l

Connections for optional
external buzzer/audible alarm

23

PJC211/212/221/222 2.0.2 - 2013

S-link device Location Serial number

(ie Thruster, AMS, PPC800 etc) (Bow, Bow-STB, Stern, Stern-STB)

Fill in the type, location and serial numbers of the S-link devices installed.
Keeping this as a reference will make the setup procedure easier!

Argentina

Trimer SA
Buenos Aires
Tel:[phone]
Fax:[phone]
www.trimer.com.ar
[e-mail]

Australia

AMI Sales
Freemantle, WA
Tel:[phone]
Fax:[phone]
[e-mail]

Austria

G. Ascherl GmbH
Hard, Bregenz
Tel:[phone]
Fax:[phone]
www.ascherl.at

of[e-mail]

Benelux

ASA Boot Electro
Watergang
Tel:[phone]
Fax:[phone]
www.asabootelectro.nl
[e-mail]

Brazil

Electra Service Ltda.
Guaruja
Tel:[phone]
Fax:[phone]
www.electraservice.com.br
[e-mail]

Bulgaria

Yachting BG
Burgas
tel: [phone]
fax: [phone]
www.yachting.bg
[e-mail]

China/Hong Kong

Storm Force Marine Ltd.
Wanchai, Hong Kong
Tel:[phone]
Fax:[phone]
www.stormforcemarine.com
[e-mail]

Croatia

Yacht Supplier
Icici
Tel:[phone]
Fax:[phone]
[e-mail]

Cyprus

Ocean Marine Equipment Ltd

Limassol
Tel: [phone]
Fax: [phone]
[e-mail]

Denmark

Side-Power Europe
Tel: [phone]
www.side-power.com
[e-mail]

Estonia/Latvia/Lithuania

Miltec Systems OÜ
Tallin
Tel: [phone]
Fax: [phone]
www.miltec.ee
[e-mail]

Finland

Side-Power Europe
Vaasa
Tel: [phone]
Fax: [phone]

kalle@engbo.

France

Kent Marine Equipment

Nantes
Tel:[phone]
Fax:[phone]
www.kent-marine.com
[e-mail]

Germany

Side-Power Europe
Tel:[phone]
www.side-power.com
[e-mail]

Greece

Amaltheia Marine
Athens
Tel:[phone]
Fax:[phone]
www.amaltheiamarine.com
[e-mail]

Iceland

Maras EHF
Reykjavik
Tel:[phone]
Fax:[phone]
www.maras.is
[e-mail]

India

Indo Marine Engineering Co. Pvt. Ltd
Pune, Maharashtra
Tel:[phone]
Fax:[phone]
[e-mail]

Israel

Atlantis Marine Ltd.
Tel Aviv
Tel:[phone]
Fax:[phone]
www.atlantis-marine.com
[e-mail]

Italy

Saim S.P.A.
Assago-Milan
Tel:[phone]
Fax:[phone]
www.saim-group.com

Japan

Turtle Marine Inc.
Nagasaki
Tel:[phone]
Fax:[phone]
www.turtle-marine.com
[e-mail]

Malta

S & D Yachts Ltd.
Cali
Tel:[phone]
Fax:[phone]
www.sdyachts.com
[e-mail]

New Zealand

Advance Trident Ltd.
Auckland
Tel:[phone]
Fax:[phone]
www.advancetrident.com
[e-mail]

Norway

Sleipner Motor AS
Fredrikstad
Tel:[phone]
Fax:[phone]
www.sleipner.no
[e-mail]

Poland

Taurus Sea Power SP. Z.O.O
Gdansk
Tel:[phone]
Fax:[phone]
www.taurus.gda.pl

Portugal

Riesnautica Lda.
Alhos Vedros
Tel:[phone]
www.riesnautica.pt
[e-mail]

Russia

Standarte
Starbeyevo
Tel:[phone]
Fax:[phone]
www.standarte.ru
[e-mail]

South Africa

PowerSol
Cape Town
Tel: [phone]
Fax: [phone]
[e-mail]

South Korea

D-I Iindustrial Co Ltd
Jinju-si, Kyungnam-do
Tel: [phone]
Fax: [phone]
www.d-i.co.kr
[e-mail]

Spain

Imnasa Marine Products
Girona
Tel:[phone]
Fax:[phone]
www.imnasa.com
[e-mail]

Sweden

Sleipner AB
Strömstad
Tel:[phone]
Fax:[phone]
www.sleipnerab.se
[e-mail]

Switzerland

Senero AG
Winterthur
Tel:[phone]
Fax:[phone]
www.senero.ch
[e-mail]

Singapore/Malaysia/ Indonesia/
Vietnam/Phillipines/Thailand

Island Marine Services Pte Ltd
Singapore
Tel:[phone]
Fax:[phone]
www.island-marine.com
[e-mail]

Taiwan

Mercury Marine Supply
Kaohsiung
Tel:[phone]
Fax:[phone]

Turkey

Denpar Ltd.
Istanbul
Tel:[phone]
Fax:[phone]
[e-mail]

UK/Ireland

Sleipner Motor Ltd.
South Brent
Tel:[phone]
Fax:[phone]
[e-mail]

Ukraine

Yachtglanz Marine Equipment

Tel:[phone]
Fax:[phone]
www.yachtglanz.com
[e-mail]

United Arab Emirates

Teignbridge Propellers & Marine

Equipment Co. Ltd.

Dubai
Tel:[phone]
Fax:[phone]
[e-mail]

USA/Canada/Carribean

Imtra Corporation
New Bedford, MA
Tel:[phone]
Fax:[phone]
www.imtra.com
[e-mail]

SIDE-POWER SERVICE CENTRES

Sleipner Motor AS • P.O. Box 591, N1612 Fredrikstad • Norway

Tel: [phone] • Fax: [phone]

[e-mail] • www.side-power.com