ShoreLand'r LUV28BXXL User Manual V.1
®
LUV28BXXL
LUV28BXXL (All Colors) Bundles Required:
ST215/75R14C TSilver Dir Rim ................................ 2
66520 Bag with Chains, No Coupler .................................. 1
69082 Literature Bag - Brake Trailers.................................. 1
80543-- Frame Bundle - LUV28BXXL .................................... 1
ShoreLand’r offers their product line a painted nish. When
ordering parts it is important that you specify the nish or color you
have on your product. The ve (5) digit number along with a two (2)
digit space _ _, note the parts which can be purchased with various
nishes. When ordering these items use the ve (5) digit number
along with a two (2) digit sufx for the proper nish.
03..........Black
39..........Galvanized w/Silver Plastic Components
LUV28BXXL Specications
Capacity 2800 lbs.
GVWR: 3740 lbs.
GAWR: 3740 lbs.
Ship Wt: 730 lbs.
Frm Size: 2X4 (11 Ga)
Tire Size: ST215X75R14-C
Rim Size: 14 X 6 “J”
Brake Size: 10” Disc Standard
Coupler: 2” UFP Model A70
Suspension: 5 Leaf Hook Springs
Tongue Size: 3x5x65” Swing Tongue
Table of Contents
Frame Drawing & Bill of Materials .........................................2-3
Swing Tongue, Actuator, Safety Chain ..................................4
Prole 2000 Winch / Jack Drawing & BOM ..........................5-6
V-Bunk Assembly ..................................................................
Tire Size & Carrying Capapcity Chart ...................................8
Chassis / Axle Assembly Dwg / BOM (Disc) .........................8-9
More Information ...................................................................10
Trailer Adjustments ...............................................................10
Midwest Industries, Inc. Ida Grove, IA 51445 800.859.3028 www.shorelandr.com 0003837
REV B 02/05/2009
Page 1
7
Diagram A
Midwest Industries, Inc. Ida Grove, IA 51445 800.859.3028 www.shorelandr.com 0003837
REV B 02/05/2009
Page 2
matching colors and ends. Push the extra wire provided into the
rear of the tongue. The wire should be positioned so the only thing
exposed to the outside of the tongue and side frame is the black
wire loom.
SAFETY CHAINS
Locate the 1/2” x 5” hex bolt. Slip the bolt through a 1/2” at washer,
then place through the last link of one of the safety chains.
Place the bolt with chain attached through the hole provided in the
bottom front of the actuator mount on the tongue. Place the second
chain on the portion of the bolt extending through the other side
of the tongue. Place on another 1/2” at washer and hex lock nut.
Tighten.
RETRACTABLE TIE DOWNS
Locate the two retractable tie downs. Next locate one of the 7/16”
x 1 ½” ne threaded bolts supplied with the retractable tie down.
Insert it into the bottom hole on the retractable tie down so the bolt
is pointing through the back side of the tie down. Insert the bolt
through the hole provided in the taillight bracket just inside the side
frame. Secure with the 7/16” ange lock nut. Tighten.
Repeat the above process on the other tie down.
WINCH POST ASSEMBLY
Your trailer may have come with the jack already installed on the
winch base. However, in the event that it did not, use the following
instructions to attach the jack to the winch base before it is installed
on the tongue.
ASSEMBLY AND MOUNTING INSTRUCTIONS:
JACK ON A PROFILE 2000 WINCH BASE
The Prole 2000 winch base used on the 2” x 4” and 2” x 5” frame
trailers is formed so that the jack can be mounted directly to it eliminating the need for other mounting hardware for attaching the jack
to the tongue. The jack required for mounting does not require the
mounting base or any of the original mounting hardware components.
Assemble as follows:
The jack must be mounted to the winch base before it is installed
on the trailer tongue. If the winch base is already mounted on the
tongue, it will have to be removed for the jack installation.
Locate the hardware bag and sort all items by size.
FINAL ASSEMBLY INSTRUCTIONS
Remove all banded items and the hardware bag from the frame.
Remove the parts and sort by size.
TONGUE
Locate the tongue and install by sliding it in the front of the tongue
channel. Line the holes in the tongue with the holes in the tongue
channel. Install the 1/2” x 4” hex bolt in the front cross hole and
secure with a 1/2” ange lock nut.
Remove the wire harness from the rear of the tongue. Place the
wire harness and the brake hose through the hole provided in the
tongue cover plate. Secure the tongue cover plate in position with
the same 1/2” x 1-1/2” hex bolt that secures the back on the tongue
to the tongue channel of the frame. Secure with a 1/2” lock nut.
Tighten both bolts just installed.
Plug the tongue wire harness ends into the frame harnesses by
Lay the Prole 2000 winch base on its side so the side that the jack
is going to be mounted on is up.
Place the inside jack spacer on the winch base so the center protrusion ts down into the indent in the winch base.
Position the jack mounting plate so it is centered around the inside
jack spacer just positioned.
Lay the jack retainer plate on top of the jack mounting plate aligning
the holes in it with the holes in the winch base.
Insert the two ½” and 1 ¼” carriage bolts into the holes just aligned
in the jack retainer plate and the winch base. Secure in place with
½” lock washers and hex nuts. Tighten.
Once tightened, rotate the jack through its normal pivoting range to
make sure it is free to travel and is not binding up.
Midwest Industries, Inc. Ida Grove, IA 51445 800.859.3028 www.shorelandr.com 0003837
REV B 02/05/2009
Page 3
Loading...