Shogun Motorsports CBR600F4, CBR600F4I User Manual

Honda CBR600F4/F4I (99-06) Frame Slider
Installation Instructions
Part Numbers: 750-3209, 750-3200 & 850-3200

MADE IN THE USA!
Carefully read instructions in their entirety before the install

Professional installation is recommended. Always use proper safety measures during the install of this
product. Do not try to install this product without proper tools, recently calibrated torque wrench,
correct torque specifications from factory service manual, safety goggles and gloves. The motorcycle
must be in a fixed secure position before the install process begins. DO NOT remove both engine studs
at the same time. Shogun is not responsible for any part of your motorcycle for any reason. Precisely
measure location of cut and if in doubt at any point please call us before the install process has begun.

Replacement Parts List: Left Side Components (as if you were sitting on the bike)
QTY Price each Part Numbers Descriptions

1 $20.00 99-FS-750-3209-L Black Left Side Puck
1 $20.00 99-FS-750-3200-L White Left Side Puck
1 $25.00 99-FS-850-3200-L Chrome Left Side Puck
1 $3.50 99-HB-SH10125090 Socket Cap 10 X 1.25 X 90 Main Engine Stud

Replacement Parts List: Right Side Components (as if you were sitting on the bike)
1 $20.00 99-FS-750-3209-R Black Right Side Puck
1 $20.00 99-FS-750-3200-R White Right Side Puck
1 $25.00 99-FS-850-3200-R Chrome Right Side Puck
1 $3.50 99-HB-SH101250110 Socket Cap 10 X 1.25 X 110 Main Engine Stud

Frame Sliders: Left frame slider is longer than right.

Installation Steps:

1. Some photos in this section are used for illustration examples only. It is up to you how you
decide to cut your motorcycles bodywork to accept the frame slider there are many different
ways customers go through this process. Shogun is not responsible for any part of your

motorcycle for any reason. Precisely measure location of cut and if in doubt at any point please

call us before the install process has begun. Professional installation is recommended. Always
use proper safety measures during the install of this product. Do not try to install this product
without proper tools, recently calibrated torque wrench, correct torque specifications from
factory service manual, safety goggles and gloves.

2. Body Prep. Use masking tape to completely mask off the area on the body where you will be
working. We usually will tape off approximately 6 to 8 inches around the though hole area and
any other edges that could get bumped or scratched while working. Tip: In some locations you
may want to double up the thickness of the masking take to give extra protection.

3. Locating and cutting the body. This is a simple illustration of how most of us install the product
here. It takes a bit longer but our end results have been more consistent with a better overall fit
and finish. We start with (99-SPOT-1012560) Shogun Spot tool. It’s nothing special just a 10mm
socket cap bolt with a 1.25 pitch that we cut the head off of and sharpen to a point. You can
purchase the tool for $12.99 or go to your local hardware store and make your own. Keep in
mind Metric 10 or 12mm X 1.25 pitch bolts (most common sportbike engine studs) are fairly
hard to find. Make sure you know the size and that the bolt you’re buying is a 1.25 pitch bolt.

With the body removed, thread in by hand your spot tool. Make sure you have the spot tool
screwed in enough to clear the body on the inside.

4. Loosely mount your bodywork and adjust the spot tool out to lightly touch the inside of the
body. Make sure you have at least 15mm of thread engagement, without that the spot tool will

tend to sag down giving you a false location. With the body mounted in the correct location use

a soft micro fiber cloth over the spot tool location and softly tap to leave a spot mark on the
inside of the body. Be careful not to scratch or chip the body.

5. Remove the bodywork and double check location of spot mark the tool has created.