Sharp PN-60TA3, PN-60TB3, PN-70TA3, PN-L603A, PN-L603B User Manual

...
0 (0)

LCD MONITOR

TOUCH PANEL DRIVER 2

 

 

 

for Mac

Version 1.0

OPERATION MANUAL

 

Applicable models

PN-L703A/PN-70TA3/PN-L703B/PN-70TB3/PN-L603A/PN-60TA3/PN-L603B/PN-60TB3

 

Contents

Introduction......................................................................

3

System Requirements..................................................

3

Setting up the Computer.................................................

4

Install............................................................................

4

Touch Panel Settings.......................................................

5

How to configure settings.............................................

5

Calibration.....................................................................

7

Properties.....................................................................

8

Uninstall..........................................................................

10

Touch Action...................................................................

11

Important Information

This software has been shipped after strict quality control and product inspection. If, however, you find any failure or malfunction, contact your product dealer.

Please understand that SHARP CORPORATION bears no responsibility for errors made during use by the customer or a third party, nor for any other malfunctions or damage to this software arising during use, except where indemnity liability is recognized under law.

Transcribing or duplicating part or all of this manual and/or this software without permission from our company is not permitted.

As a part of our policy of continuous improvement, SHARP reserves the right to make design and specification changes for product improvement without prior notice.

The contents or details may vary depending on the screen configuration and OS version, etc.

This manual does not contain basic operating instructions for Mac OS.

Trademarks

Apple, Mac and Mac OS are registered trademarks of Apple Inc.

Intel is a trademark or registered trademark of Intel Corporation or its subsidiaries in the U.S.A. and other countries.

All other brand and product names are trademarks or registered trademarks of their respective holders.

E 2

Introduction

System Requirements

The touch panel driver 2 is a program that enables you to use the touch panel to operate the computer that is connected to the touch panel.

To use the touch panel, the touch panel must be connected to a computer, and the touch panel driver 2 must be installed on the computer.

OS

Mac OS X v10.7, Mac OS X v10.8, Mac OS X v10.9

CPU

Intel processor

Memory

At least 2 GB

Free space on hard drive

At least 5 MB

TIPS

Depending on the application software, touch operation may not be possible (for example, if the application processes mouse and other operations independently).

3 E

Setting up the Computer

Install

Caution

To install, an administrator name (user name) and password are required.

If an older version of the touch panel driver 2 is installed, remove (uninstall) the old version before installing the touch panel driver 2. (See page 10.)

Do not touch the touch panel when connecting the USB cable.

If you touch the touch panel, it will lead to a malfunction. In this case, disconnect and then reconnect the USB cable.

1.Start your computer.

2.Exit all applications that are running.

3.Connect the USB cable for the touch panel to the computer.

 

USB 1 port*

To the USB terminal

USB 2 port*

of the PC

 

USB cable

*To use a touch panel with a computer connected to the bottom, connect to the USB 1 port. To use a touch panel with a computer connected to the side, connect to the USB 2 port. (Factory setting. Can be changed in TOUCH INPUT SELECT in the SETUP menu.)

4.Run the setup program.

(1)Double-click the “TouchPanel” folder, and then double-click the “Mac” folder.

(2)Double-click “SharpTouchPanel2.pkg”.

5.Click “Continue”.

Follow the on-screen instructions to install the driver.

If a screen prompting you to enter the name and password appears, enter the name and password of the administrator and click “Install Software” (or “OK”).

If the “When this software finishes installing, you must restart your computer. Are you sure you want to install the software now?” screen appears, click “Continue Installation”.

6.When the installation finished screen appears, click “Restart”.

This completes the installation of the touch panel driver 2.

Each time the computer is started, the touch panel driver 2 will start automatically to enable the touch panel to be used.

E 4

Sharp PN-60TA3, PN-60TB3, PN-70TA3, PN-L603A, PN-L603B User Manual

Touch Panel Settings

The touch panel driver 2 starts automatically and the icon () appears on the menu bar.

TIPS

If PN-L703A/PN-70TA3 (or PN-L703B/PN-70TB3) and PN-L603A/PN-60TA3 (or PN-L603B/PN-60TB3) are connected at the same time, selecting a setting item will display the screen where you can select the model to apply the setting to.

How to configure settings nConfiguring settings from the menu bar

1.

Click the touch panel driver 2 icon ( ) on the menu bar.

2.

Click a menu to change a setting.

Current Resolution: The model currently being used and the current screen resolution appear.

Calibration: See page 7.

Properties: See page 8.

Hardware Information: Hardware information appears.

Version Information: Shows the version of the touch panel driver 2.

Disable TP Driver:

Select to disable the touch panel function.

To disable a single touch panel function, see “Function Setting”. (See page 9.)

nConfiguring settings from System Preferences

1.Click “System Preferences” from the Apple menu ().

2.Click “SharpTouchPanel2”.

3.Click the menu and select settings.

Menu

 

TIPS

 

• If the “Show Setting Utility in menu bar” checkmark is removed, the touch panel driver 2 icon (

) does not appear on the

 

menu bar.

 

5 E

Loading...
+ 10 hidden pages