Loading...
PN-L802B PN-L702B PN-L602B
LCD MONITOR
TOUCH PANEL DRIVER OPERATION MANUAL
Version 2.2
Contents
Setting up the PC............................................................. |
3 |
Installing the touch panel driver.................................... |
3 |
Touch Panel Settings....................................................... |
4 |
How to configure settings............................................. |
4 |
Calibration..................................................................... |
5 |
Properties..................................................................... |
6 |
Uninstalling the Driver Software..................................... |
8 |
This manual explains the installation and configuration of the touch panel driver
Important Information
•This software has been shipped after strict quality control and product inspection. If, however, you find any failure or malfunction, contact your product dealer.
•Please understand that SHARP CORPORATION bears no responsibility for errors made during use by the customer or a third party, nor for any other malfunctions or damage to this software arising during use, except where indemnity liability is recognized under law.
•Transcribing or duplicating part or all of this manual and/or this software without permission from our company is not permitted.
•As a part of our policy of continuous improvement, SHARP reserves the right to make design and specification changes for product improvement without prior notice. The performance specification figures indicated are nominal values of production units. There may be some deviations from these values in individual units.
•The contents or details may vary depending on the screen configuration and OS version, etc.
•Only an English version of the touch panel driver is provided. The screens shown in the manual are the screens that appear in the English OS.
•This manual does not contain basic operating instructions for Windows.
Trademarks
•Microsoft, Windows, and Windows Vista are either registered trademarks or trademarks of Microsoft Corporation in the United States and/or other countries.
•All other brand and product names are trademarks or registered trademarks of their respective holders.
E 2
Setting up the PC
To use the touch panel, the touch panel driver must be installed from the supplied CD-ROM and the touch panel must be connected to your PC.
Installing the touch panel driver
The touch panel driver is a program that enables you to use the touch panel to operate the PC that is connected to the touch panel.
Caution
•This can only be done by a user with administrator authority.
•If an older version of the touch panel driver is installed, remove (uninstall) the old version before installing the touch panel driver. (See page 8.)
•If you are using a USB hub, use a self-powered hub (a hub capable of supplying a 500 mA current). The touch panel will not operate correctly if a bus-powered USB hub is used.
•Do not touch the touch panel when connecting the USB cable.
If you touch the touch panel, this may be detected as an element failure in the infrared transmitter/receiver and malfunctioning will result. In this case, disconnect and then reconnect the USB cable.
1.Start your PC.
2.Exit all applications that are running.
3.Connect the USB cable for the touch panel to the PC.
After it has been connected, the touch panel will be automatically recognized.
To the USB terminal of the PC
USB port
USB cable (Supplied)
PN-L802B
USB port
4.Insert the supplied CD-ROM into the CD-ROM drive of your PC.
5.Open the CD-ROM drive in “Computer” or “My Computer”.
6.Double-click the “TouchPanel” folder.
7.Double-click the install file.
•If you are using a 32-bit operating system, double-click “TPDriverSetup32.exe”.
•If you are using a 64-bit operating system, double-click “TPDriverSetup64.exe”.
•When the “User Account Control” screen appears, click “Yes” (or “Allow”).
8.Click “Next”.
Follow the on-screen instructions to install the driver.
•If the “Windows Security” screen appears, click “Install” (or “Install this driver software anyway”).
•If the “Software Installation” screen appears, click “Continue Anyway”.
•If the “Touch Panel Driver Files in Use” screen appears, click “Continue”.
9.When the installation finished screen appears, click “Close”.
10.If a screen appears prompting you to restart your PC, click “Yes”.
This completes the installation of the touch panel driver.
Each time the PC is started, the touch panel driver will start automatically to enable the touch panel to be used. The first time you use the touch panel, perform calibration (position adjustment). (See page 5.)
3 E
Loading...